Author SHA1 Message Date
Alan SterembergandClaude Opus 5.5 9e70212e87 Sim: follow the 20260927 release
- sim.v: the coco3fpga ports changed (RED_O/GREEN_O/BLUE_O, PROBE_O/PROBE_I,
  Display_Debug) and so did the switch word (rs_swap, UART_INPUT, and the cart
  interrupt option on SWITCH[9]); mirror CoCo3.sv. SNAC inputs idle high.
- rtl/ovo.v: Verilog translation of the new rtl/OVO.vhd overlay; the
  Makefile drops the removed Mister_Video_GIMEX.v.
- PIX_CLK is now a clk_sys enable, high 2 of every 4 cycles, fed to the
  mixer's ce_pix. Capture video as video_mixer.sv does: on a clk_sys rising
  edge, one pixel per rising edge of the enable.
- New reference screenshots: the release's video timing moves the picture
  about 2 pixels; text checks unchanged.
- Commit tests/dw_boot.sh, which the dw_boot* ignore pattern was hiding.

Co-Authored-By: Claude Opus 5.5 (1M context) <[email protected]>
2026-10-02 07:29:18 -04:00
Alan SterembergandClaude Opus 5.5 50d76dd489 OSD: move "Cart Interrupt Disabled" to status[19] / SWITCH[9]
The 20260927 release reused status[16] / SWITCH[4] for "Swap MiSTer Uart"
(rs_swap) and dropped the "Cart Interrupt Disabled" item that the cart
start-up change wires into the slot 3 CART interrupt. Bring the item back in
the Debug menu on a free status bit (OJ, status[19]) and pass it through the
unused SWITCH[9].

Co-Authored-By: Claude Opus 5.5 (1M context) <[email protected]>
2026-10-02 07:29:18 -04:00
Alan SterembergandClaude Opus 5.5 4afcebf22a Video fetch: register the end-of-line test before the SDRAM ack
coco_mem_fetch.sv compared read_count against WORD_END_COUNT on the same
114 MHz edge that took SDRAM_VID_ACK and updated VID_READ_OFFSET, the fetch
address; that path missed timing (-0.7 ns). read_count only changes on the
ack, so the compare is now registered in state_start with identical results.

Co-Authored-By: Claude Opus 5.5 (1M context) <[email protected]>
2026-10-02 07:15:44 -04:00
Alan SterembergandClaude Opus 5.5 72a50a16bb Cart start-up: cold boot "DK" carts; wire up "Cart Interrupt Disabled"
A cart loaded after boot in Multi-Pak slot 3 made CART toggle every CPU cycle
forever -- the autostart of a program pak, whose CART pin is tied to Q. A
disk-style ROM (HDB-DOS, Disk BASIC) never drives CART; BASIC starts it from
the "DK" signature at power-on. Under the toggling, FujiNet's CFGLOAD.BIN
(which re-enables the CART interrupt) hung in an endless FIRQ after 17
DriveWire reads; an OSD reset cleared it.

- A cart whose first two bytes are "DK" now gets a cold boot (the existing
  AMW/EE_Cold_Bt path) instead of the autostart interrupt.
- OSD "Cart Interrupt Disabled" (status[16] -> SWITCH[4]) was not connected;
  it now suppresses the slot-3 autostart interrupt.
- Program paks are unchanged: Arkanoid loaded after boot still autostarts.

Verified in the Verilator sim with the hardware sequence (cart loaded after
boot, slot 3, no reset): the FujiNet S3 cart now reads all 98 sectors of
CONFIG, matching the MiSTer after a manual reset. Regression tests unchanged.

The sim gains --cart-frame N to load the cart after boot, as the OSD and MGL
do; loading it before reset had hidden the problem.

Co-Authored-By: Claude Opus 5.5 (1M context) <[email protected]>
2026-10-02 07:15:44 -04:00
Alan SterembergandClaude Opus 5.5 874f4f3083 Add Verilator simulation (ImGui + headless)
verilator/ runs the core on the host with the shared FM-7 / Apple-IIgs sim
framework: windowed (ImGui/SDL2) or --headless, typing on a frame schedule,
screenshots, text-screen dump, 6809 disassembly trace, floppy/SDC/cart/cassette,
and RS-232 Pak serial debugging (TXD decoder, RXD driver, pty bridge, ACIA
trace) with a minimal DriveWire server and a script to run the real FujiNet
daemon against the sim. See verilator/README.md.

- The VHDL the build uses (ROMs, RAMs, font) is converted to Verilog in
  verilator/rtl/; the VHDL CPU is not instantiated (CoCo3_CYC_ACC_6809).
- sdram2.sv is simulated with its own controller logic and an SDR chip model.
- run_tests.sh: boot, keyboard, disk, WIDTH 80 and HSCREEN tests, judged on
  the text screen and byte-for-byte against test-ref/ screenshots.

rtl/wd1793.sv: spt_addr and buff_wr are declared at module scope instead of
inside generate blocks. They are assigned outside those blocks; Quartus
accepted it, Verilator rejected spt_addr and silently split buff_wr into a
separate net. No change on the FPGA (FM-7 made the same fix).

Co-Authored-By: Claude Opus 5.5 (1M context) <[email protected]>
2026-10-02 07:15:44 -04:00
Alan SterembergandClaude Opus 5.5 aae1ceabf1 RS-232 Pak: decode in any MPI slot; clock the receiver from the baud generator
Two bugs kept the FujiNet HDB-DOS SY6551 carts from working:

- $FF68-$FF6B were decoded only when the Multi-Pak I/O select was slot 1
  (MPI_SCS == 0), which the OSD cannot select. With the cart in slot 3 the
  6551 was unreachable: HDB-DOS polled status forever and sent nothing. On a
  real CoCo the SCS line covers only $FF40-$FF5F and the RS-232 Pak decodes
  $FF68 itself, so it now answers in any slot.

- With CTL bit 4 = 0 ("external receive clock") the receiver ran off the fixed
  1.8475 MHz enable, i.e. 115,200 baud. HDBDW3L3_19200.CCC writes CTL=$0F, so
  it transmitted at 19,200 and received at 115,200 -- every DriveWire sector
  failed its checksum. The receiver now uses the baud generator (RX_CLK =
  TX_CLK); unchanged for CTL=$1x and for baud select 0.

Verified in the Verilator sim against the real FujiNet daemon (FujiNet-PC):
the L3 cart at 19,200 loads FujiNet CONFIG with no checksum errors.

Co-Authored-By: Claude Opus 5.5 (1M context) <[email protected]>
2026-10-02 07:15:44 -04:00
shodge12 8b8cf72d1f Release Compiled Version 20260927
Release Compiled Version 20260927
2026-10-02 01:05:24 -04:00
shodge12 ede23da6b0 Timing fixes, Video mode fixes, Sound cleanup, and enabling RS-232 to physical SNAC pins.
1.	Overlay support for the detection of no rom loading on power up AND misc
    debugging. [done]
2.	Fix video HSCREEN 4 mode which is used in some demos and rs-232 terminal
	programs. [done]
3.	Reworked sound output to faithfully emulate the analog muxing in the coco.
	[done]
4.	Routing RS-232 tx/rx lines to the SNAC port for initial serial debugging
	of Fuji-Net interface. [done - untested]
2026-10-02 00:49:54 -04:00
shodge12 77ee8b8c8c First Stage Timing Updates
Changed generation of PIX_CLK.  It is no longer CLK_14, instead it is created in coco3video_mister and pushed outward. (as it should be).  Video1.stp is for watching the video signals.
The ability of using a old GIMEX video file has been removed as a feature.
2026-01-13 23:54:33 -05:00
jackyangantelope 0cc97c86d9 Update sys (#17) 2025-12-09 21:57:03 +08:00
shodge12 1da70a7929 Core changes and CSAVE support.
1.	Added support for cassette save.  To use: A) You have to have a file [anyname.cas]
	which is larger than needed.  B) Select the file through the UI Menu 'Save
	Cassette'.  C)Set 'Cass Rwd=0 / Rec=1' to 1. D) Issue your 'CSAVE "NAME"'
	E) When done, set 'Cass Rwd=0 / Rec=1' to 0 to complete the write.  The file can
	now be loaded or copied.  Note a dummy file of a specific size can be created in
	the MiSTer SSH shell in the /media/fat/games/coco3 with the command:
	'truncate -s 65536 tapefileame.cas'. [Note do NOT use over 65536 file length]
2.	Fixed serial interrupt [6551] to not be functional on slot 3 [carts].
3.	Modification of sys_top.v to override use of USER_IO for HDMI - so it can be used
	for logic analyzer debug.  This will only occur when `define	Config_Debug is
	enabled in config.v.
4.	Fixed MUGS of powerup issue occurring on some MiSTer units.
5.	Fixed incorrect application of GIME_IRQ on legacy interrupts.  Fixed race condition
	on reading IRQ status vs clearing the interrupt.
6.	Improved Castle of Tharoggad.  App now loads but locks as the graphics animate.  This
	change improved mmu usage through to CARTS.
7.	Builds now keep track of multiple builds in the same date.  It shows as V240512-001 in
	the menus.  Its also exposed to BASIC and a boot.vhd which can be enabled to autorun is
	supplied in the archive to show how it works.
8.	Additionally, on the boot.vhd disk, is a program which demonstrated how to load a font -
	IBMFONT.BAS. Run it and it maps a font much like the IBM font to the 80 column format.
	Also, a file called TESTRTC.BAS pulls the MiSTer RTC values exposed in BASIC to display
	a clock.
9.	Large improvement in the Timer function.  Code closer emulates COCO3 Timer. Fixes
	Sliphead cart.
10.	In the 20231023 release the wd1773 instances were reduced to 1 for the FDC and one for
	the FDC.  This saved space but introduced a bug when using multiple drives at the same
	time - like a copy command.  This change was removed and the copy command works again.

To Do...
1.	Add Speech / Music cart
2.	Fix Castle of Tharoggad
2024-05-14 23:00:16 -04:00
shodge12 a3373d34b9 First working csave version...
Note output files do not expand.  Therefore you need a large output file before you select it, turn on record and save.
2024-03-24 17:19:52 -04:00
shodge12 06e91ee2ae Initial Baseline for feature Cassette Write
Fix 1 bit time...
2024-03-23 00:25:55 -04:00
shodge12 f940be1a2b Release 20240318
1. Changed PIA 2 addressing to align with real CoCo3 hardware and end at FF2F.
2. Re-arranged MiSTer drive LUNs to support future auto-boot from SDC drive 0.
3. Added 'Auto Run' feature. You must use slot 2 [SDC]. Take your floopy or HD
   and copy it to a file name of 'boot.vhd'. This will be auto mounted to drive 0
   on the SDC. In the menu, find a new item Auto Run:. It can be set to No, DOS or
   AUTO.BAS. Choosing dos causes the 'DOS' command to be executed on power up. Setting
   the option to 'AUTO.BAS' will cause a 'RUN"AUTO' command to be executed upon powerup.
   Save your settings to cause the changes to be remembered. The Auto Run system re-arms
   upon using the 'Cold Boot' menu item.
4.	Fixed MiSTer / CoCo3 interface preventing the joysticks ever reaching the
	max value of 63. Specifically '>' was changed to '>=' the DTOA values.
	This fixes DonPan and is verified in Diagnostics 2.0.
5.	HiRES[3] is used to enable some of the higher resolution graphics modes
	Gary Becker designed into CoCo3FPGA, and while these are not fully
	supported, the control signals such as HiRES[3] at $FF98 bit 6 affectt
	the graphics engine.  For some reason Color File II manipultes this bit
	and was causing it not to work.  This change requires the SG6 extensions
	to be enabled to set HiRES[3].  So specifically in the Video Settings
	insure CoCo3 LC is set to Yes.  Color File II now works properly.
2024-03-18 18:22:32 -04:00
142 changed files with 85971 additions and 3922 deletions

No files matched your search

+1
View File
@@ -10,3 +10,4 @@ jtag.cdf
greybox_tmp/cbx_args.txt greybox_tmp/cbx_args.txt
*/greybox_tmp/cbx_args.txt */greybox_tmp/cbx_args.txt
changes.txt changes.txt
rtl/config_inc.sv
BIN
View File
Binary file not shown.
+118 -272
View File
@@ -28,7 +28,7 @@ set_global_assignment -name TIMEQUEST_MULTICORNER_ANALYSIS OFF
set_global_assignment -name OPTIMIZE_POWER_DURING_FITTING OFF set_global_assignment -name OPTIMIZE_POWER_DURING_FITTING OFF
set_global_assignment -name FINAL_PLACEMENT_OPTIMIZATION ALWAYS set_global_assignment -name FINAL_PLACEMENT_OPTIMIZATION ALWAYS
set_global_assignment -name FITTER_EFFORT "STANDARD FIT" set_global_assignment -name FITTER_EFFORT "STANDARD FIT"
set_global_assignment -name OPTIMIZATION_MODE "AGGRESSIVE PERFORMANCE" set_global_assignment -name OPTIMIZATION_MODE "HIGH PERFORMANCE EFFORT"
set_global_assignment -name ALLOW_POWER_UP_DONT_CARE ON set_global_assignment -name ALLOW_POWER_UP_DONT_CARE ON
set_global_assignment -name QII_AUTO_PACKED_REGISTERS NORMAL set_global_assignment -name QII_AUTO_PACKED_REGISTERS NORMAL
set_global_assignment -name ROUTER_LCELL_INSERTION_AND_LOGIC_DUPLICATION ON set_global_assignment -name ROUTER_LCELL_INSERTION_AND_LOGIC_DUPLICATION ON
@@ -55,280 +55,126 @@ set_global_assignment -name SEED 1
#enable it only if 8bit indexed mode is used in core #enable it only if 8bit indexed mode is used in core
#set_global_assignment -name VERILOG_MACRO "MISTER_FB_PALETTE=1" #set_global_assignment -name VERILOG_MACRO "MISTER_FB_PALETTE=1"
#set_global_assignment -name VERILOG_MACRO "MISTER_DUAL_SDRAM=1"
#do not enable DEBUG_NOHDMI in release! #do not enable DEBUG_NOHDMI in release!
#set_global_assignment -name VERILOG_MACRO "MISTER_DEBUG_NOHDMI=1" #set_global_assignment -name VERILOG_MACRO "MISTER_DEBUG_NOHDMI=1"
source sys/sys.tcl # disable bilinear filtering when downscaling
set_global_assignment -name FAMILY "Cyclone V" #set_global_assignment -name VERILOG_MACRO "MISTER_DOWNSCALE_NN=1"
set_global_assignment -name DEVICE 5CSEBA6U23I7
set_global_assignment -name DEVICE_FILTER_PACKAGE UFBGA
set_global_assignment -name DEVICE_FILTER_PIN_COUNT 672
set_global_assignment -name DEVICE_FILTER_SPEED_GRADE 7
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to ADC_CONVST
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to ADC_SCK
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to ADC_SDI
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to ADC_SDO
set_location_assignment PIN_U9 -to ADC_CONVST
set_location_assignment PIN_V10 -to ADC_SCK
set_location_assignment PIN_AC4 -to ADC_SDI
set_location_assignment PIN_AD4 -to ADC_SDO
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to ARDUINO_IO[*]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to ARDUINO_IO[*]
set_instance_assignment -name CURRENT_STRENGTH_NEW "MAXIMUM CURRENT" -to ARDUINO_IO[*]
set_location_assignment PIN_U14 -to IO_SCL
set_location_assignment PIN_AG9 -to IO_SDA
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to IO_S*
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to IO_S*
set_instance_assignment -name CURRENT_STRENGTH_NEW "MAXIMUM CURRENT" -to IO_S*
set_location_assignment PIN_AF17 -to USER_IO[6]
set_location_assignment PIN_AF15 -to USER_IO[5]
set_location_assignment PIN_AG16 -to USER_IO[4]
set_location_assignment PIN_AH11 -to USER_IO[3]
set_location_assignment PIN_AH12 -to USER_IO[2]
set_location_assignment PIN_AH9 -to USER_IO[1]
set_location_assignment PIN_AG11 -to USER_IO[0]
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to USER_IO[*]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to USER_IO[*]
set_instance_assignment -name CURRENT_STRENGTH_NEW "MAXIMUM CURRENT" -to USER_IO[*]
set_location_assignment PIN_AH7 -to SDCD_SPDIF
set_instance_assignment -name CURRENT_STRENGTH_NEW "MAXIMUM CURRENT" -to SDCD_SPDIF
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to SDCD_SPDIF
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to SDCD_SPDIF
set_location_assignment PIN_Y11 -to SDRAM_A[0]
set_location_assignment PIN_AA26 -to SDRAM_A[1]
set_location_assignment PIN_AA13 -to SDRAM_A[2]
set_location_assignment PIN_AA11 -to SDRAM_A[3]
set_location_assignment PIN_W11 -to SDRAM_A[4]
set_location_assignment PIN_Y19 -to SDRAM_A[5]
set_location_assignment PIN_AB23 -to SDRAM_A[6]
set_location_assignment PIN_AC23 -to SDRAM_A[7]
set_location_assignment PIN_AC22 -to SDRAM_A[8]
set_location_assignment PIN_C12 -to SDRAM_A[9]
set_location_assignment PIN_AB26 -to SDRAM_A[10]
set_location_assignment PIN_AD17 -to SDRAM_A[11]
set_location_assignment PIN_D12 -to SDRAM_A[12]
set_location_assignment PIN_Y17 -to SDRAM_BA[0]
set_location_assignment PIN_AB25 -to SDRAM_BA[1]
set_location_assignment PIN_E8 -to SDRAM_DQ[0]
set_location_assignment PIN_V12 -to SDRAM_DQ[1]
set_location_assignment PIN_D11 -to SDRAM_DQ[2]
set_location_assignment PIN_W12 -to SDRAM_DQ[3]
set_location_assignment PIN_AH13 -to SDRAM_DQ[4]
set_location_assignment PIN_D8 -to SDRAM_DQ[5]
set_location_assignment PIN_AH14 -to SDRAM_DQ[6]
set_location_assignment PIN_AF7 -to SDRAM_DQ[7]
set_location_assignment PIN_AE24 -to SDRAM_DQ[8]
set_location_assignment PIN_AD23 -to SDRAM_DQ[9]
set_location_assignment PIN_AE6 -to SDRAM_DQ[10]
set_location_assignment PIN_AE23 -to SDRAM_DQ[11]
set_location_assignment PIN_AG14 -to SDRAM_DQ[12]
set_location_assignment PIN_AD5 -to SDRAM_DQ[13]
set_location_assignment PIN_AF4 -to SDRAM_DQ[14]
set_location_assignment PIN_AH3 -to SDRAM_DQ[15]
set_location_assignment PIN_AG13 -to SDRAM_DQML
set_location_assignment PIN_AF13 -to SDRAM_DQMH
set_location_assignment PIN_AD20 -to SDRAM_CLK
set_location_assignment PIN_AG10 -to SDRAM_CKE
set_location_assignment PIN_AA19 -to SDRAM_nWE
set_location_assignment PIN_AA18 -to SDRAM_nCAS
set_location_assignment PIN_Y18 -to SDRAM_nCS
set_location_assignment PIN_W14 -to SDRAM_nRAS
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to SDRAM_*
set_instance_assignment -name CURRENT_STRENGTH_NEW "MAXIMUM CURRENT" -to SDRAM_*
set_instance_assignment -name FAST_OUTPUT_REGISTER ON -to SDRAM_*
set_instance_assignment -name FAST_OUTPUT_ENABLE_REGISTER ON -to SDRAM_DQ[*]
set_instance_assignment -name FAST_INPUT_REGISTER ON -to SDRAM_DQ[*]
set_instance_assignment -name ALLOW_SYNCH_CTRL_USAGE OFF -to *|SDRAM_*
set_location_assignment PIN_AE15 -to SD_SPI_CS
set_location_assignment PIN_AH8 -to SD_SPI_MISO
set_location_assignment PIN_AG8 -to SD_SPI_CLK
set_location_assignment PIN_U13 -to SD_SPI_MOSI
set_instance_assignment -name CURRENT_STRENGTH_NEW "MAXIMUM CURRENT" -to SD_SPI*
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to SD_SPI*
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to SD_SPI*
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to FPGA_CLK1_50
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to FPGA_CLK2_50
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to FPGA_CLK3_50
set_location_assignment PIN_V11 -to FPGA_CLK1_50
set_location_assignment PIN_Y13 -to FPGA_CLK2_50
set_location_assignment PIN_E11 -to FPGA_CLK3_50
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to HDMI_I2C_*
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to HDMI_I2S
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to HDMI_LRCLK
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to HDMI_MCLK
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to HDMI_SCLK
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to HDMI_TX_*
set_instance_assignment -name FAST_OUTPUT_REGISTER ON -to HDMI_TX_D[*]
set_instance_assignment -name FAST_OUTPUT_REGISTER ON -to HDMI_TX_DE
set_instance_assignment -name FAST_OUTPUT_REGISTER ON -to HDMI_TX_HS
set_instance_assignment -name FAST_OUTPUT_REGISTER ON -to HDMI_TX_VS
set_instance_assignment -name FAST_OUTPUT_REGISTER ON -to HDMI_TX_CLK
set_location_assignment PIN_U10 -to HDMI_I2C_SCL
set_location_assignment PIN_AA4 -to HDMI_I2C_SDA
set_location_assignment PIN_T13 -to HDMI_I2S
set_location_assignment PIN_T11 -to HDMI_LRCLK
set_location_assignment PIN_U11 -to HDMI_MCLK
set_location_assignment PIN_T12 -to HDMI_SCLK
set_location_assignment PIN_AG5 -to HDMI_TX_CLK
set_location_assignment PIN_AD19 -to HDMI_TX_DE
set_location_assignment PIN_AD12 -to HDMI_TX_D[0]
set_location_assignment PIN_AE12 -to HDMI_TX_D[1]
set_location_assignment PIN_W8 -to HDMI_TX_D[2]
set_location_assignment PIN_Y8 -to HDMI_TX_D[3]
set_location_assignment PIN_AD11 -to HDMI_TX_D[4]
set_location_assignment PIN_AD10 -to HDMI_TX_D[5]
set_location_assignment PIN_AE11 -to HDMI_TX_D[6]
set_location_assignment PIN_Y5 -to HDMI_TX_D[7]
set_location_assignment PIN_AF10 -to HDMI_TX_D[8]
set_location_assignment PIN_Y4 -to HDMI_TX_D[9]
set_location_assignment PIN_AE9 -to HDMI_TX_D[10]
set_location_assignment PIN_AB4 -to HDMI_TX_D[11]
set_location_assignment PIN_AE7 -to HDMI_TX_D[12]
set_location_assignment PIN_AF6 -to HDMI_TX_D[13]
set_location_assignment PIN_AF8 -to HDMI_TX_D[14]
set_location_assignment PIN_AF5 -to HDMI_TX_D[15]
set_location_assignment PIN_AE4 -to HDMI_TX_D[16]
set_location_assignment PIN_AH2 -to HDMI_TX_D[17]
set_location_assignment PIN_AH4 -to HDMI_TX_D[18]
set_location_assignment PIN_AH5 -to HDMI_TX_D[19]
set_location_assignment PIN_AH6 -to HDMI_TX_D[20]
set_location_assignment PIN_AG6 -to HDMI_TX_D[21]
set_location_assignment PIN_AF9 -to HDMI_TX_D[22]
set_location_assignment PIN_AE8 -to HDMI_TX_D[23]
set_location_assignment PIN_T8 -to HDMI_TX_HS
set_location_assignment PIN_AF11 -to HDMI_TX_INT
set_location_assignment PIN_V13 -to HDMI_TX_VS
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to KEY[0]
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to KEY[1]
set_location_assignment PIN_AH17 -to KEY[0]
set_location_assignment PIN_AH16 -to KEY[1]
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to LED[0]
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to LED[1]
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to LED[2]
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to LED[3]
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to LED[4]
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to LED[5]
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to LED[6]
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to LED[7]
set_location_assignment PIN_W15 -to LED[0]
set_location_assignment PIN_AA24 -to LED[1]
set_location_assignment PIN_V16 -to LED[2]
set_location_assignment PIN_V15 -to LED[3]
set_location_assignment PIN_AF26 -to LED[4]
set_location_assignment PIN_AE26 -to LED[5]
set_location_assignment PIN_Y16 -to LED[6]
set_location_assignment PIN_AA23 -to LED[7]
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to SW[0]
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to SW[1]
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to SW[2]
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to SW[3]
set_location_assignment PIN_Y24 -to SW[0]
set_location_assignment PIN_W24 -to SW[1]
set_location_assignment PIN_W21 -to SW[2]
set_location_assignment PIN_W20 -to SW[3]
set_hps_location_assignment HPSINTERFACEPERIPHERALSPIMASTER_X52_Y72_N111 -to spi
set_hps_location_assignment HPSINTERFACEPERIPHERALUART_X52_Y67_N111 -to uart
set_hps_location_assignment HPSINTERFACEPERIPHERALI2C_X52_Y60_N111 -to hdmi_i2c
set_global_assignment -name PRE_FLOW_SCRIPT_FILE "quartus_sh:sys/build_id.tcl"
set_global_assignment -name CDF_FILE jtag.cdf
set_global_assignment -name QIP_FILE sys/sys.qip
source sys/sys_analog.tcl
set_location_assignment PIN_AF25 -to SDIO_DAT[0]
set_location_assignment PIN_AF23 -to SDIO_DAT[1]
set_location_assignment PIN_AD26 -to SDIO_DAT[2]
set_location_assignment PIN_AF28 -to SDIO_DAT[3]
set_location_assignment PIN_AF27 -to SDIO_CMD
set_location_assignment PIN_AH26 -to SDIO_CLK
set_instance_assignment -name CURRENT_STRENGTH_NEW "MAXIMUM CURRENT" -to SDIO_*
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to SDIO_*
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to SDIO_DAT[*]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to SDIO_CMD
set_location_assignment PIN_AE17 -to VGA_R[0]
set_location_assignment PIN_AE20 -to VGA_R[1]
set_location_assignment PIN_AF20 -to VGA_R[2]
set_location_assignment PIN_AH18 -to VGA_R[3]
set_location_assignment PIN_AH19 -to VGA_R[4]
set_location_assignment PIN_AF21 -to VGA_R[5]
set_location_assignment PIN_AE19 -to VGA_G[0]
set_location_assignment PIN_AG15 -to VGA_G[1]
set_location_assignment PIN_AF18 -to VGA_G[2]
set_location_assignment PIN_AG18 -to VGA_G[3]
set_location_assignment PIN_AG19 -to VGA_G[4]
set_location_assignment PIN_AG20 -to VGA_G[5]
set_location_assignment PIN_AG21 -to VGA_B[0]
set_location_assignment PIN_AA20 -to VGA_B[1]
set_location_assignment PIN_AE22 -to VGA_B[2]
set_location_assignment PIN_AF22 -to VGA_B[3]
set_location_assignment PIN_AH23 -to VGA_B[4]
set_location_assignment PIN_AH21 -to VGA_B[5]
set_location_assignment PIN_AH22 -to VGA_HS
set_location_assignment PIN_AG24 -to VGA_VS
set_location_assignment PIN_AH27 -to VGA_EN
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to VGA_EN
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to VGA_*
set_instance_assignment -name CURRENT_STRENGTH_NEW 8MA -to VGA_*
set_location_assignment PIN_AC24 -to AUDIO_L
set_location_assignment PIN_AE25 -to AUDIO_R
set_location_assignment PIN_AG26 -to AUDIO_SPDIF
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to AUDIO_*
set_instance_assignment -name CURRENT_STRENGTH_NEW 8MA -to AUDIO_*
set_location_assignment PIN_Y15 -to LED_USER
set_location_assignment PIN_AA15 -to LED_HDD
set_location_assignment PIN_AG28 -to LED_POWER
set_location_assignment PIN_AH24 -to BTN_USER
set_location_assignment PIN_AG25 -to BTN_OSD
set_location_assignment PIN_AG23 -to BTN_RESET
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to LED_*
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to BTN_*
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to BTN_*
source files.qip
set_global_assignment -name VHDL_FILE rtl/sram/coco_ram.vhd
set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_cart.vhd
set_global_assignment -name VHDL_FILE rtl/rom/coco3_char_rom.vhd
set_global_assignment -name VERILOG_FILE rtl/PS2_Key/ps2_keyboard.v
set_global_assignment -name MIF_FILE rtl/VDAC.mif
set_global_assignment -name VERILOG_FILE rtl/VDAC.v
set_global_assignment -name VERILOG_FILE rtl/Mister_Video.v
set_global_assignment -name VERILOG_FILE rtl/cocokey.v
set_global_assignment -name VERILOG_FILE rtl/UART_6551/uart_6551.v
set_global_assignment -name VERILOG_FILE rtl/UART_6551/6551tx.v
set_global_assignment -name VERILOG_FILE rtl/UART_6551/6551rx.v
set_global_assignment -name VHDL_FILE rtl/CPU09/cpu09l_128a.vhd
set_global_assignment -name SYSTEMVERILOG_FILE rtl/coco3fpga.sv
set_global_assignment -name VERILOG_FILE rtl/cassette.v
set_global_assignment -name VERILOG_FILE rtl/rtc.sv
set_global_assignment -name VERILOG_FILE rtl/AMW.v
set_global_assignment -name VERILOG_FILE rtl/square_gen.v
set_global_assignment -name VERILOG_FILE rtl/config.v
set_global_assignment -name SYSTEMVERILOG_FILE rtl/fdc.sv
set_global_assignment -name SYSTEMVERILOG_FILE rtl/sdc.sv
set_global_assignment -name SYSTEMVERILOG_FILE rtl/sdc_top.sv
set_global_assignment -name SYSTEMVERILOG_FILE rtl/ps2_mouse.v
set_global_assignment -name SYSTEMVERILOG_FILE rtl/sdram/sdram2.sv
set_global_assignment -name SYSTEMVERILOG_FILE rtl/wd1793.sv
set_global_assignment -name SYSTEMVERILOG_FILE CoCo3.sv
set_global_assignment -name VHDL_FILE rtl/sram/coco_vid_ram_buf.vhd
set_global_assignment -name SYSTEMVERILOG_FILE rtl/coco_mem_fetch.sv
set_global_assignment -name VERILOG_FILE rtl/EE_Cold_Bt.v
set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_32K.vhd
set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_8K.vhd
set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_16.vhd
set_global_assignment -name SDC_FILE rtl/CoCo3FPGA.sdc
# disable adaptive scanline filtering
#set_global_assignment -name VERILOG_MACRO "MISTER_DISABLE_ADAPTIVE=1"
#use only 1MB per frame for scaler to free ~21MB DDR3 RAM
#set_global_assignment -name VERILOG_MACRO "MISTER_SMALL_VBUF=1"
# Disable YC / Composite output to save some resources
#set_global_assignment -name VERILOG_MACRO "MISTER_DISABLE_YC=1"
# Disable ALSA audio output to save some resources
#set_global_assignment -name VERILOG_MACRO "MISTER_DISABLE_ALSA=1"
source sys/sys.tcl
source sys/sys_analog.tcl
source files.qip
set_global_assignment -name ENABLE_SIGNALTAP ON set_global_assignment -name ENABLE_SIGNALTAP ON
set_global_assignment -name SIGNALTAP_FILE Video_Explorer.stp set_global_assignment -name USE_SIGNALTAP_FILE Video1.stp
set_global_assignment -name SIGNALTAP_FILE rom_Exploror.stp1 set_global_assignment -name SLD_NODE_CREATOR_ID 110 -section_id Video1
set_global_assignment -name SOURCE_FILE rom_Exploror.stp1 set_global_assignment -name SLD_NODE_ENTITY_NAME sld_signaltap -section_id Video1
set_global_assignment -name SIGNALTAP_FILE Serial.stp set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_clk -to "emu:emu|video_mixer:video_mixer|CLK_VIDEO" -section_id Video1
set_global_assignment -name SIGNALTAP_FILE AMW.stp set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[0] -to "emu:emu|VGA_DE" -section_id Video1
set_global_assignment -name SIGNALTAP_FILE HD.stp set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[1] -to "emu:emu|VGA_F1" -section_id Video1
set_global_assignment -name SIGNALTAP_FILE reset.stp set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[2] -to "emu:emu|VGA_G[7]" -section_id Video1
set_global_assignment -name SIGNALTAP_FILE Vsync.stp set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[3] -to "emu:emu|VGA_HS" -section_id Video1
set_global_assignment -name ENABLE_SIGNALTAP OFF set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[4] -to "emu:emu|VGA_VS" -section_id Video1
set_global_assignment -name OPTIMIZATION_MODE "HIGH PERFORMANCE EFFORT" set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[5] -to "emu:emu|video_mixer:video_mixer|HBlank" -section_id Video1
set_global_assignment -name USE_SIGNALTAP_FILE Video_Explorer2.stp set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[6] -to "emu:emu|video_mixer:video_mixer|HSync" -section_id Video1
set_global_assignment -name VERILOG_FILE rtl/mc6809glb/mc6809glb.v set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[7] -to "emu:emu|video_mixer:video_mixer|VBlank" -section_id Video1
set_global_assignment -name SIGNALTAP_FILE Video_Explorer2.stp set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[8] -to "emu:emu|video_mixer:video_mixer|VSync" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[9] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ce_pix" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[10] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[0]" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[11] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[1]" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[12] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hb" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[13] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hs" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[14] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|old_ce" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[15] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vb" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[16] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vs" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[17] -to "emu:emu|video_mixer:video_mixer|video_freezer:freezer|hs_out" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_trigger_in[18] -to "emu:emu|video_mixer:video_mixer|video_freezer:freezer|vs_out" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[0] -to "emu:emu|VGA_DE" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[1] -to "emu:emu|VGA_F1" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[2] -to "emu:emu|VGA_G[7]" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[3] -to "emu:emu|VGA_HS" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[4] -to "emu:emu|VGA_VS" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[5] -to "emu:emu|video_mixer:video_mixer|HBlank" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[6] -to "emu:emu|video_mixer:video_mixer|HSync" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[7] -to "emu:emu|video_mixer:video_mixer|VBlank" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[8] -to "emu:emu|video_mixer:video_mixer|VSync" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[9] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ce_pix" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[10] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[0]" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[11] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[1]" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[12] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hb" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[13] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hs" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[14] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|old_ce" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[15] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vb" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[16] -to "emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vs" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[17] -to "emu:emu|video_mixer:video_mixer|video_freezer:freezer|hs_out" -section_id Video1
set_instance_assignment -name CONNECT_TO_SLD_NODE_ENTITY_PORT acq_data_in[18] -to "emu:emu|video_mixer:video_mixer|video_freezer:freezer|vs_out" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_RAM_BLOCK_TYPE=AUTO" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_DATA_BITS=19" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_TRIGGER_BITS=19" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_STORAGE_QUALIFIER_BITS=19" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_NODE_INFO=805334528" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_POWER_UP_TRIGGER=0" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_INVERSION_MASK=000000000000000000000000000000000000000000000000000000000000000000000000000000000000" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_INVERSION_MASK_LENGTH=84" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_STORAGE_QUALIFIER_INVERSION_MASK_LENGTH=0" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_SEGMENT_SIZE=8192" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_ATTRIBUTE_MEM_MODE=OFF" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_STATE_FLOW_USE_GENERATED=0" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_STATE_BITS=11" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_BUFFER_FULL_STOP=1" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_CURRENT_RESOURCE_WIDTH=1" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_INCREMENTAL_ROUTING=1" -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[0] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[1] -to Video1|gnd -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[2] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[3] -to Video1|gnd -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[4] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[5] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[6] -to Video1|gnd -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[7] -to Video1|gnd -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[8] -to Video1|gnd -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[9] -to Video1|gnd -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[10] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[11] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[12] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[13] -to Video1|gnd -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[14] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[15] -to Video1|gnd -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[16] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[17] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[18] -to Video1|gnd -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[19] -to Video1|gnd -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[20] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[21] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[22] -to Video1|gnd -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[23] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[24] -to Video1|gnd -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[25] -to Video1|gnd -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[26] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[27] -to Video1|gnd -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[28] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[29] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[30] -to Video1|vcc -section_id Video1
set_instance_assignment -name POST_FIT_CONNECT_TO_SLD_NODE_ENTITY_PORT crc[31] -to Video1|gnd -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_TRIGGER_LEVEL=1" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_SAMPLE_DEPTH=8192" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_TRIGGER_IN_ENABLED=0" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_TRIGGER_PIPELINE=0" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_RAM_PIPELINE=0" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_COUNTER_PIPELINE=0" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_ADVANCED_TRIGGER_ENTITY=basic,1," -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_TRIGGER_LEVEL_PIPELINE=1" -section_id Video1
set_global_assignment -name SLD_NODE_PARAMETER_ASSIGNMENT "SLD_ENABLE_ADVANCED_TRIGGER=0" -section_id Video1
set_global_assignment -name SLD_FILE db/Video1_auto_stripped.stp
set_instance_assignment -name PARTITION_HIERARCHY root_partition -to | -section_id Top set_instance_assignment -name PARTITION_HIERARCHY root_partition -to | -section_id Top
+65 -31
View File
@@ -1,6 +1,6 @@
//============================================================================ //============================================================================
// CoCo3 port to MiSTer // CoCo3 port to MiSTer
// Copyright (c) 2019 Alan Steremberg - alanswx // Copyright (c) 2019 Alan Steremberg - alanswx, Stan Hodge - MasterS3263827
// //
// //
//============================================================================ //============================================================================
@@ -43,6 +43,8 @@ module emu
input [11:0] HDMI_WIDTH, input [11:0] HDMI_WIDTH,
input [11:0] HDMI_HEIGHT, input [11:0] HDMI_HEIGHT,
output HDMI_FREEZE, output HDMI_FREEZE,
output HDMI_BLACKOUT,
output HDMI_BOB_DEINT,
`ifdef MISTER_FB `ifdef MISTER_FB
// Use framebuffer in DDRAM // Use framebuffer in DDRAM
@@ -180,6 +182,8 @@ assign LED_POWER = 0;
assign VGA_SCALER = 0; assign VGA_SCALER = 0;
assign HDMI_FREEZE = 0; assign HDMI_FREEZE = 0;
assign HDMI_BLACKOUT = 0;
assign HDMI_BOB_DEINT = 0;
wire [1:0] ar = status[9:8]; wire [1:0] ar = status[9:8];
@@ -189,6 +193,8 @@ assign VIDEO_ARY = (!ar) ? 12'd3 : 12'd0;
`include "build_id.v" `include "build_id.v"
`include "build_id_num.v"
localparam CONF_STR = { localparam CONF_STR = {
"COCO3;UART19200:9600:4800:2400:1200:300;", "COCO3;UART19200:9600:4800:2400:1200:300;",
"-;", "-;",
@@ -213,8 +219,11 @@ localparam CONF_STR = {
"F2,CAS,Load Cassette;", "F2,CAS,Load Cassette;",
"TF,Stop & Rewind;", "TF,Stop & Rewind;",
"OH,Monitor Tape Sound,No,Yes;", "OH,Monitor Tape Sound,No,Yes;",
"-;", "-;",
"S6,CAS,Save Cassette;",
"OE,Cass Rwd=0 / Rec=1,0,1;",
"-;",
"P1,Video Settings;", "P1,Video Settings;",
"P1-;", "P1-;",
"P1-, -= Video Settings =-;", "P1-, -= Video Settings =-;",
@@ -232,7 +241,10 @@ localparam CONF_STR = {
"P2-, -= Debug Menu =-;", "P2-, -= Debug Menu =-;",
"P2-;", "P2-;",
"P2F3,BIN,Load COCO Font;", "P2F3,BIN,Load COCO Font;",
"P2OG,Cart Interrupt Disabled,OFF,ON;", "P2OG,Swap MiSTer Uart,RS CART,Default;",
"P2OU,Swap Uart to IO,RS IO,MiSTer;",
"P2OT,Display Debug,Off,On;",
"P2OJ,Cart Interrupt Disabled,OFF,ON;",
"-;", "-;",
"ON,D-Pad Joystick emu,No,Yes;", "ON,D-Pad Joystick emu,No,Yes;",
"O6,Swap Joysticks,Off,On;", "O6,Swap Joysticks,Off,On;",
@@ -249,7 +261,7 @@ localparam CONF_STR = {
"J,Button1,Button2;", "J,Button1,Button2;",
"jn,A,B;", "jn,A,B;",
"v,51;", "v,51;",
"V,v",`BUILD_DATE "V,v",{`BUILD_DATE,"-",`BUILD_NUMBER}
}; };
// Status bits Directory // Status bits Directory
@@ -261,9 +273,9 @@ localparam CONF_STR = {
// 0123456789ABCDEFGHIJKLMNOPQRSTUV 0123456789ABCDEFGHIJKLMNOPQRSTUV // 0123456789ABCDEFGHIJKLMNOPQRSTUV 0123456789ABCDEFGHIJKLMNOPQRSTUV
// //
// R OOOO OOR OO TOOOOOOROOOOOO ooo oo oo // R OOOO OOR OOOTOOOOOOROOOOOOOO ooo oo oo
//F FF //F FF
//S SSSSSS //S SSSSSSS
//////////////////// CLOCKS /////////////////// //////////////////// CLOCKS ///////////////////
@@ -274,7 +286,7 @@ assign clk_sys=CLK_57;
wire pll_locked, pll2_locked; wire pll_locked, pll2_locked;
wire CLK_114, CLK_57, CLK_28, CLK_14; wire CLK_114, CLK_57, CLK_28, CLK_14;
assign VGA_DISABLE = 1'b0;
pll pll pll pll
( (
@@ -314,9 +326,10 @@ wire [21:0] gamma_bus;
assign CLK_VIDEO = clk_sys; assign CLK_VIDEO = clk_sys;
wire [64:0] RTC; wire [64:0] RTC;
wire [15:0] sdram_sz;
// SD - 6 drives [4 fdc and 2 sdc] 512 size blocks [the wd1793 translates to a 256 byte sector size] // SD - 7 drives [4 fdc, 2 sdc and 1 cass_wr] 512 size blocks [the wd1793 translates to a 256 byte sector size]
hps_io #(.CONF_STR(CONF_STR),.PS2DIV(2400), .VDNUM(6), .BLKSZ(2)) hps_io hps_io #(.CONF_STR(CONF_STR),.PS2DIV(2400), .VDNUM(7), .BLKSZ(2)) hps_io
( (
.clk_sys(clk_sys), .clk_sys(clk_sys),
.HPS_BUS(HPS_BUS), .HPS_BUS(HPS_BUS),
@@ -339,6 +352,8 @@ hps_io #(.CONF_STR(CONF_STR),.PS2DIV(2400), .VDNUM(6), .BLKSZ(2)) hps_io
.ioctl_dout(ioctl_data), .ioctl_dout(ioctl_data),
.ioctl_index(ioctl_index), .ioctl_index(ioctl_index),
.sdram_sz(sdram_sz),
// SD block level interface // SD block level interface
.img_mounted(img_mounted), // signaling that new image has been mounted .img_mounted(img_mounted), // signaling that new image has been mounted
@@ -373,21 +388,21 @@ hps_io #(.CONF_STR(CONF_STR),.PS2DIV(2400), .VDNUM(6), .BLKSZ(2)) hps_io
); );
// SD block level interface // SD block level interface
wire [5:0] img_mounted; wire [6:0] img_mounted;
wire img_readonly; wire img_readonly;
wire [63:0] img_size; wire [63:0] img_size;
wire [31:0] sd_lba[6]; wire [31:0] sd_lba[7];
wire [5:0] sd_blk_cnt[6]; wire [5:0] sd_blk_cnt[7];
wire [5:0] sd_rd; wire [6:0] sd_rd;
wire [5:0] sd_wr; wire [6:0] sd_wr;
wire [5:0] sd_ack; wire [6:0] sd_ack;
// SD byte level access. Signals for 2-PORT altsyncram. // SD byte level access. Signals for 2-PORT altsyncram.
wire [8:0] sd_buff_addr; wire [8:0] sd_buff_addr;
wire [7:0] sd_buff_dout; wire [7:0] sd_buff_dout;
wire [7:0] sd_buff_din[6]; wire [7:0] sd_buff_din[7];
wire sd_buff_wr; wire sd_buff_wr;
@@ -452,7 +467,9 @@ wire Programmed_EE;
EE_Cold_Bt COCO3_EE_Cold_Bt ( EE_Cold_Bt COCO3_EE_Cold_Bt (
.CLK(CLK_14), .CLK(CLK_14),
.RESET(1'b0),
// .Display_EE(1'b0), // from MISTer subsystem
.Display_EE(easter_egg), // from MISTer subsystem .Display_EE(easter_egg), // from MISTer subsystem
.Cold_Boot(AMW_ACK), // from AMW system .Cold_Boot(AMW_ACK), // from AMW system
@@ -471,10 +488,16 @@ wire [7:0] r;
wire [7:0] g; wire [7:0] g;
wire [7:0] b; wire [7:0] b;
wire easter_egg = ~status[10]; wire easter_egg = status[10];
wire [31:0] probe; wire [6:0] probe_o;
wire [6:0] probe_i;
assign USER_OUT[6:0] = probe[6:0]; assign USER_OUT[6:0] = probe_o[6:0];
assign probe_i[6:0] = USER_IN[6:0];
wire [71:0] Config_Data;
assign Config_Data = {`BUILD_DATE, `BUILD_NUMBER};
coco3fpga coco3 ( coco3fpga coco3 (
// CLOCKS // CLOCKS
@@ -488,9 +511,9 @@ coco3fpga coco3 (
// Reset // Reset
.COCO_RESET_N((~reset & Programmed_RESET_N)), .COCO_RESET_N((~reset & Programmed_RESET_N)),
.RED(r), .RED_O(r),
.GREEN(g), .GREEN_O(g),
.BLUE(b), .BLUE_O(b),
.EE_N(Programmed_EE), .EE_N(Programmed_EE),
.PHASE(PHASE), .PHASE(PHASE),
@@ -519,7 +542,7 @@ coco3fpga coco3 (
// R1, L2, R2, L1 // R1, L2, R2, L1
.P_SWITCH(~{coco_joy2[4],coco_joy1[5],coco_joy2[5],coco_joy1[4]}), .P_SWITCH(~{coco_joy2[4],coco_joy1[5],coco_joy2[5],coco_joy1[4]}),
.SWITCH(switch), .SWITCH(switch),
.SOUND_OUT(cocosound), // .SOUND_OUT(cocosound),
.SOUND_LEFT(audio_left), .SOUND_LEFT(audio_left),
.SOUND_RIGHT(AUDIO_R), .SOUND_RIGHT(AUDIO_R),
@@ -530,6 +553,9 @@ coco3fpga coco3 (
.ioctl_index(ioctl_index), .ioctl_index(ioctl_index),
.ioctl_wr(ioctl_wr), .ioctl_wr(ioctl_wr),
// SDRAM Info
.sdram_sz(sdram_sz),
// SD block level interface // SD block level interface
.img_mounted(img_mounted), // signaling that new image has been mounted .img_mounted(img_mounted), // signaling that new image has been mounted
@@ -549,7 +575,8 @@ coco3fpga coco3 (
.sd_buff_din(sd_buff_din), .sd_buff_din(sd_buff_din),
.sd_buff_wr(sd_buff_wr), .sd_buff_wr(sd_buff_wr),
.PROBE(probe[31:0]), .PROBE_O(probe_o),
.PROBE_I(probe_i),
.clk_Q_out(clk_Q_out), .clk_Q_out(clk_Q_out),
.casdout( casdout), .casdout( casdout),
.cas_relay(cas_relay), .cas_relay(cas_relay),
@@ -577,6 +604,7 @@ coco3fpga coco3 (
.RTC(RTC), .RTC(RTC),
.AMW_Trigger(coldboot | mpi_reset | mem_reset), .AMW_Trigger(coldboot | mpi_reset | mem_reset),
// .AMW_Trigger(coldboot),
.AMW_ACK(AMW_ACK), .AMW_ACK(AMW_ACK),
.F_Turbo(F_Turbo), .F_Turbo(F_Turbo),
@@ -585,6 +613,9 @@ coco3fpga coco3 (
.AUTO_MODE(Auto_Mode), .AUTO_MODE(Auto_Mode),
.Config_Data(Config_Data),
.Display_Debug(display_debug),
.UART_TXD(UART_TXD), .UART_TXD(UART_TXD),
.UART_RXD(UART_RXD), .UART_RXD(UART_RXD),
.UART_RTS(UART_RTS), .UART_RTS(UART_RTS),
@@ -595,7 +626,7 @@ coco3fpga coco3 (
assign status_set = 1'b0; assign status_set = 1'b0;
wire [5:0] cocosound; //wire [5:0] cocosound;
wire [2:0] turbo_speed = status[34:32]; wire [2:0] turbo_speed = status[34:32];
wire [2:0] assigned_turbo_speed; wire [2:0] assigned_turbo_speed;
@@ -604,11 +635,12 @@ wire [1:0] Auto_Mode = status[41:40];
wire AMW_ACK; wire AMW_ACK;
wire cpu_speed = status[11]; //wire cpu_speed = status[11];
wire [1:0] mpi = status[13:12] + 1'b1; wire [1:0] mpi = status[13:12] + 1'b1;
wire video=status[14]; //wire video=status[14];
wire cartint=status[16]; wire CASS_REW_RECORD=status[14];
wire rs_swap=status[16];
wire sg4v6 = status[21]; wire sg4v6 = status[21];
wire PHASE = status[18]; wire PHASE = status[18];
@@ -618,7 +650,9 @@ wire coldboot = status[22];
wire F_Turbo = status[24]; wire F_Turbo = status[24];
wire [2:0] Mem_Size = status[27:25]; wire [2:0] Mem_Size = status[27:25];
wire SWAP_M_J = status[28]; wire SWAP_M_J = status[28];
wire display_debug = status[29];
wire UART_INPUT = status[30];
wire cartint = status[19];
wire digitalJoy = status[23]; wire digitalJoy = status[23];
reg [2:0] mpi_d = 2'b00; reg [2:0] mpi_d = 2'b00;
reg first_mpi_chg = 1'b0; reg first_mpi_chg = 1'b0;
@@ -655,7 +689,7 @@ begin
end end
// Set bit 9 to swap serial ports... // Set bit 9 to swap serial ports...
wire [9:0] switch = { 2'b10,art,sg4v6,cartint,video,mpi,cpu_speed} ; wire [9:0] switch = { cartint,UART_INPUT,art,sg4v6,rs_swap,CASS_REW_RECORD,mpi,1'b0};
wire reset = RESET | status[0] | buttons[1]; wire reset = RESET | status[0] | buttons[1];
@@ -737,7 +771,7 @@ cassette cassette(
.sdram_addr(ram_addr), .sdram_addr(ram_addr),
.sdram_data(ram_data_o), .sdram_data(ram_data_o),
.sdram_rd(ram_rd), // Not connected for sram // .sdram_rd(ram_rd), // Not connected for sram
.data(casdout) .data(casdout)
); );
+214
View File
@@ -0,0 +1,214 @@
<session jtag_chain="DE-SoC on yoda [USB-1]" jtag_device="@2: 5CSEBA6(.|ES)/5CSEMA6/.. (0x02D020DD)" sof_file="">
<display_tree gui_logging_enabled="0">
<display_branch instance="Video1" log="USE_GLOBAL_TEMP" signal_set="USE_GLOBAL_TEMP" trigger="USE_GLOBAL_TEMP"/>
</display_tree>
<instance enabled="true" entity_name="sld_signaltap" is_auto_node="yes" is_expanded="true" name="Video1" source_file="sld_signaltap.vhd">
<node_ip_info instance_id="0" mfg_id="110" node_id="0" version="6"/>
<signal_set global_temp="1" is_expanded="true" name="signal_set: 2026/01/10 19:34:25 #0">
<clock name="emu:emu|video_mixer:video_mixer|CLK_VIDEO" polarity="posedge" tap_mode="classic"/>
<config pipeline_level="0" ram_type="AUTO" reserved_data_nodes="0" reserved_storage_qualifier_nodes="0" reserved_trigger_nodes="0" sample_depth="8192" trigger_in_enable="no" trigger_out_enable="no"/>
<top_entity/>
<signal_vec>
<trigger_input_vec>
<wire name="emu:emu|VGA_DE" tap_mode="classic"/>
<wire name="emu:emu|VGA_F1" tap_mode="classic"/>
<wire name="emu:emu|VGA_G[7]" tap_mode="classic"/>
<wire name="emu:emu|VGA_HS" tap_mode="classic"/>
<wire name="emu:emu|VGA_VS" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|HBlank" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|HSync" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|VBlank" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|VSync" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ce_pix" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[0]" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[1]" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hb" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hs" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|old_ce" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vb" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vs" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|video_freezer:freezer|hs_out" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|video_freezer:freezer|vs_out" tap_mode="classic"/>
</trigger_input_vec>
<data_input_vec>
<wire name="emu:emu|VGA_DE" tap_mode="classic"/>
<wire name="emu:emu|VGA_F1" tap_mode="classic"/>
<wire name="emu:emu|VGA_G[7]" tap_mode="classic"/>
<wire name="emu:emu|VGA_HS" tap_mode="classic"/>
<wire name="emu:emu|VGA_VS" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|HBlank" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|HSync" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|VBlank" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|VSync" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ce_pix" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[0]" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[1]" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hb" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hs" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|old_ce" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vb" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vs" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|video_freezer:freezer|hs_out" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|video_freezer:freezer|vs_out" tap_mode="classic"/>
</data_input_vec>
<storage_qualifier_input_vec>
<wire name="emu:emu|VGA_DE" tap_mode="classic"/>
<wire name="emu:emu|VGA_F1" tap_mode="classic"/>
<wire name="emu:emu|VGA_G[7]" tap_mode="classic"/>
<wire name="emu:emu|VGA_HS" tap_mode="classic"/>
<wire name="emu:emu|VGA_VS" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|HBlank" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|HSync" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|VBlank" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|VSync" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ce_pix" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[0]" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[1]" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hb" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hs" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|old_ce" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vb" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vs" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|video_freezer:freezer|hs_out" tap_mode="classic"/>
<wire name="emu:emu|video_mixer:video_mixer|video_freezer:freezer|vs_out" tap_mode="classic"/>
</storage_qualifier_input_vec>
</signal_vec>
<presentation>
<unified_setup_data_view>
<node data_index="2" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="rising edge" name="emu:emu|VGA_G[7]" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="2" tap_mode="classic" trigger_index="2" type="unknown"/>
<node data_index="4" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|VGA_VS" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="4" tap_mode="classic" trigger_index="4" type="unknown"/>
<node data_index="3" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|VGA_HS" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="3" tap_mode="classic" trigger_index="3" type="unknown"/>
<node data_index="0" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|VGA_DE" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="0" tap_mode="classic" trigger_index="0" type="unknown"/>
<node data_index="1" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|VGA_F1" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="1" tap_mode="classic" trigger_index="1" type="unknown"/>
<node data_index="8" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|VSync" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="8" tap_mode="classic" trigger_index="8" type="unknown"/>
<node data_index="6" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|HSync" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="6" tap_mode="classic" trigger_index="6" type="unknown"/>
<node data_index="7" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|VBlank" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="7" tap_mode="classic" trigger_index="7" type="unknown"/>
<node data_index="5" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|HBlank" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="5" tap_mode="classic" trigger_index="5" type="unknown"/>
<node data_index="17" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|video_freezer:freezer|hs_out" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="17" tap_mode="classic" trigger_index="17" type="unknown"/>
<node data_index="18" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|video_freezer:freezer|vs_out" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="18" tap_mode="classic" trigger_index="18" type="unknown"/>
<node data_index="14" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|old_ce" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="14" tap_mode="classic" trigger_index="14" type="unknown"/>
<node data_index="13" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hs" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="13" tap_mode="classic" trigger_index="13" type="unknown"/>
<node data_index="16" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vs" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="16" tap_mode="classic" trigger_index="16" type="unknown"/>
<node data_index="12" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hb" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="12" tap_mode="classic" trigger_index="12" type="unknown"/>
<node data_index="15" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vb" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="15" tap_mode="classic" trigger_index="15" type="unknown"/>
<node data_index="9" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ce_pix" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="9" tap_mode="classic" trigger_index="9" type="unknown"/>
<node is_selected="false" level-0="alt_or" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[1..0]" order="msb_to_lsb" storage-0="alt_or" storage-1="alt_or" storage-2="alt_or" type="register">
<node data_index="11" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[1]" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="11" tap_mode="classic" trigger_index="11" type="unknown"/>
<node data_index="10" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[0]" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="10" tap_mode="classic" trigger_index="10" type="unknown"/>
</node>
</unified_setup_data_view>
<data_view>
<net data_index="2" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="rising edge" name="emu:emu|VGA_G[7]" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="2" tap_mode="classic" trigger_index="2" type="unknown"/>
<net data_index="4" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|VGA_VS" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="4" tap_mode="classic" trigger_index="4" type="unknown"/>
<net data_index="3" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|VGA_HS" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="3" tap_mode="classic" trigger_index="3" type="unknown"/>
<net data_index="0" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|VGA_DE" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="0" tap_mode="classic" trigger_index="0" type="unknown"/>
<net data_index="1" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|VGA_F1" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="1" tap_mode="classic" trigger_index="1" type="unknown"/>
<net data_index="8" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|VSync" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="8" tap_mode="classic" trigger_index="8" type="unknown"/>
<net data_index="6" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|HSync" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="6" tap_mode="classic" trigger_index="6" type="unknown"/>
<net data_index="7" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|VBlank" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="7" tap_mode="classic" trigger_index="7" type="unknown"/>
<net data_index="5" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|HBlank" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="5" tap_mode="classic" trigger_index="5" type="unknown"/>
<net data_index="17" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|video_freezer:freezer|hs_out" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="17" tap_mode="classic" trigger_index="17" type="unknown"/>
<net data_index="18" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|video_freezer:freezer|vs_out" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="18" tap_mode="classic" trigger_index="18" type="unknown"/>
<net data_index="14" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|old_ce" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="14" tap_mode="classic" trigger_index="14" type="unknown"/>
<net data_index="13" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hs" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="13" tap_mode="classic" trigger_index="13" type="unknown"/>
<net data_index="16" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vs" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="16" tap_mode="classic" trigger_index="16" type="unknown"/>
<net data_index="12" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hb" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="12" tap_mode="classic" trigger_index="12" type="unknown"/>
<net data_index="15" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vb" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="15" tap_mode="classic" trigger_index="15" type="unknown"/>
<net data_index="9" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ce_pix" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="9" tap_mode="classic" trigger_index="9" type="unknown"/>
<bus is_selected="false" level-0="alt_or" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[1..0]" order="msb_to_lsb" storage-0="alt_or" storage-1="alt_or" storage-2="alt_or" type="register">
<net data_index="11" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[1]" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="11" tap_mode="classic" trigger_index="11" type="unknown"/>
<net data_index="10" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[0]" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="10" tap_mode="classic" trigger_index="10" type="unknown"/>
</bus>
</data_view>
<setup_view>
<net data_index="2" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="rising edge" name="emu:emu|VGA_G[7]" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="2" tap_mode="classic" trigger_index="2" type="unknown"/>
<net data_index="4" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|VGA_VS" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="4" tap_mode="classic" trigger_index="4" type="unknown"/>
<net data_index="3" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|VGA_HS" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="3" tap_mode="classic" trigger_index="3" type="unknown"/>
<net data_index="0" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|VGA_DE" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="0" tap_mode="classic" trigger_index="0" type="unknown"/>
<net data_index="1" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|VGA_F1" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="1" tap_mode="classic" trigger_index="1" type="unknown"/>
<net data_index="8" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|VSync" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="8" tap_mode="classic" trigger_index="8" type="unknown"/>
<net data_index="6" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|HSync" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="6" tap_mode="classic" trigger_index="6" type="unknown"/>
<net data_index="7" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|VBlank" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="7" tap_mode="classic" trigger_index="7" type="unknown"/>
<net data_index="5" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|HBlank" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="5" tap_mode="classic" trigger_index="5" type="unknown"/>
<net data_index="17" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|video_freezer:freezer|hs_out" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="17" tap_mode="classic" trigger_index="17" type="unknown"/>
<net data_index="18" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|video_freezer:freezer|vs_out" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="18" tap_mode="classic" trigger_index="18" type="unknown"/>
<net data_index="14" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|old_ce" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="14" tap_mode="classic" trigger_index="14" type="unknown"/>
<net data_index="13" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hs" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="13" tap_mode="classic" trigger_index="13" type="unknown"/>
<net data_index="16" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vs" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="16" tap_mode="classic" trigger_index="16" type="unknown"/>
<net data_index="12" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|hb" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="12" tap_mode="classic" trigger_index="12" type="unknown"/>
<net data_index="15" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|vb" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="15" tap_mode="classic" trigger_index="15" type="unknown"/>
<net data_index="9" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ce_pix" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="9" tap_mode="classic" trigger_index="9" type="unknown"/>
<bus is_selected="false" level-0="alt_or" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[1..0]" order="msb_to_lsb" storage-0="alt_or" storage-1="alt_or" storage-2="alt_or" type="register">
<net data_index="11" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[1]" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="11" tap_mode="classic" trigger_index="11" type="unknown"/>
<net data_index="10" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" name="emu:emu|video_mixer:video_mixer|gamma_corr:gamma|ctr[0]" pwr_level-0="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="10" tap_mode="classic" trigger_index="10" type="unknown"/>
</bus>
</setup_view>
<trigger_in_editor/>
<trigger_out_editor/>
</presentation>
<trigger CRC="74B35C35" attribute_mem_mode="false" gap_record="true" global_temp="1" name="trigger: 2026/01/13 02:01:16 #0" position="pre" power_up_trigger_mode="false" record_data_gap="true" segment_size="2048" storage_mode="off" storage_qualifier_disabled="no" storage_qualifier_port_is_pin="true" storage_qualifier_port_name="auto_stp_external_storage_qualifier" storage_qualifier_port_tap_mode="classic" trigger_type="circular">
<power_up_trigger position="pre" storage_qualifier_disabled="no"/>
<events use_custom_flow_control="no">
<level enabled="yes" name="condition1" type="basic">'emu:emu|VGA_G[7]' == rising edge
<power_up enabled="yes">
</power_up>
<op_node>
<op_node left="452" top="174" type="Advanced Trigger Level Result"/>
</op_node>
</level>
</events>
<storage_qualifier_events>
<transitional>1111111111111111111
<pwr_up_transitional>1111111111111111111</pwr_up_transitional>
</transitional>
<storage_qualifier_level type="basic">
<power_up>
</power_up>
<op_node/>
</storage_qualifier_level>
<storage_qualifier_level type="basic">
<power_up>
</power_up>
<op_node/>
</storage_qualifier_level>
<storage_qualifier_level type="basic">
<power_up>
</power_up>
<op_node/>
</storage_qualifier_level>
</storage_qualifier_events>
<log>
<data global_temp="1" name="log: Trig @ 2026/01/13 02:05:12 (0:0:0.2 elapsed)" power_up_mode="false" sample_depth="8192" trigger_position="1024">10000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000000010000000001000000001100010000100000000001001000010000000001100000001000000001000000000100000000110001000010000000000100100001000000000110000000100000000100000000010000000011000100001000000000010010000100000000011000000010000100010000000001000010001101010000100001000001101000010000100001110000001000010001001000000100001000110101000010000100000110100001000010000111000000100001000100100000010000100011010100000000010000011010000000001000011100000000000100010010000000000010001101010000000001000001101000000000100001110000000000010001001000000000001000110101000000000100000110100000000010000111000000000001000100100000000000100011010100000000010000011010000000001000011100000000000100010010000000000010001101010000000001000001101000000000100001110000000000010001001000000000001000110101000000000100000110100000000010000111000000000001000100100000000000100011010100000000010000011010000000001000011100000000000100010010000000000010001101010000000001000001101000000000100001110000000000010001001000000000001000110101000000000100000110100000000010000111000000000001000100100000000000100011010100000000010000011010000000001000011100000000000100010010000000000010001101010000000001000001101000000000100001110000000000010001001000000000001000110101000000000100000110100000000010000111000000000001000100100000Line truncated
<extradata>1111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111T11111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111Line truncated
</log>
</trigger>
</signal_set>
<position_info>
<single attribute="active tab" value="0"/>
<single attribute="data horizontal scroll position" value="0"/>
<single attribute="data vertical scroll position" value="0"/>
<single attribute="setup horizontal scroll position" value="0"/>
<single attribute="setup vertical scroll position" value="0"/>
<single attribute="zoom level denominator" value="1"/>
<single attribute="zoom level numerator" value="1"/>
<single attribute="zoom offset denominator" value="1"/>
<single attribute="zoom offset numerator" value="122880"/>
<multi attribute="timebars" size="2" value="1626,4678"/>
</position_info>
</instance>
<mnemonics/>
<static_plugin_mnemonics/>
<global_info>
<single attribute="active instance" value="0"/>
<single attribute="config widget visible" value="1"/>
<single attribute="data log widget visible" value="0"/>
<single attribute="hierarchy widget height" value="96"/>
<single attribute="hierarchy widget visible" value="0"/>
<single attribute="instance widget visible" value="1"/>
<single attribute="jtag widget visible" value="1"/>
<single attribute="lock mode" value="0"/>
<multi attribute="column width" size="23" value="34,34,443,74,68,78,95,96,98,98,88,88,110,101,101,101,101,101,101,101,101,107,66"/>
<multi attribute="frame size" size="2" value="1204,686"/>
<multi attribute="jtag widget size" size="2" value="348,135"/>
</global_info>
</session>
+229 -101
View File
@@ -1,130 +1,264 @@
<session jtag_chain="DE-SoC on 192.168.2.129 [USB-1]" jtag_device="@2: 5CSEBA6(.|ES)/5CSEMA6/.. (0x02D020DD)" sof_file=""> <session jtag_chain="DE-SoC on 192.168.2.129 [USB-1]" jtag_device="@2: 5CSEBA6(.|ES)/5CSEMA6/.. (0x02D020DD)" sof_file="">
<display_tree gui_logging_enabled="0"> <display_tree gui_logging_enabled="0">
<display_branch instance="auto_signaltap_0" signal_set="USE_GLOBAL_TEMP" trigger="USE_GLOBAL_TEMP"/> <display_branch instance="auto_signaltap_0" log="USE_GLOBAL_TEMP" signal_set="USE_GLOBAL_TEMP" trigger="USE_GLOBAL_TEMP"/>
</display_tree> </display_tree>
<instance enabled="false" entity_name="sld_signaltap" is_auto_node="yes" is_expanded="true" name="auto_signaltap_0" source_file="sld_signaltap.vhd"> <instance enabled="true" entity_name="sld_signaltap" is_auto_node="yes" is_expanded="true" name="auto_signaltap_0" source_file="sld_signaltap.vhd">
<node_ip_info instance_id="0" mfg_id="110" node_id="0" version="6"/> <node_ip_info instance_id="0" mfg_id="110" node_id="0" version="6"/>
<signal_set global_temp="1" is_expanded="true" name="signal_set: 2024/02/02 23:05:26 #0"> <position_info>
<clock name="emu:emu|coco3fpga:coco3|CLK_14" polarity="posedge" tap_mode="classic"/> <single attribute="active tab" value="0"/>
<config pipeline_level="0" ram_type="AUTO" reserved_data_nodes="0" reserved_storage_qualifier_nodes="0" reserved_trigger_nodes="0" sample_depth="256" trigger_in_enable="no" trigger_out_enable="no"/> <single attribute="data horizontal scroll position" value="0"/>
<single attribute="data vertical scroll position" value="0"/>
<single attribute="setup horizontal scroll position" value="296"/>
<single attribute="setup vertical scroll position" value="2"/>
<single attribute="zoom level denominator" value="1"/>
<single attribute="zoom level numerator" value="1"/>
<single attribute="zoom offset denominator" value="1"/>
<single attribute="zoom offset numerator" value="129024"/>
<multi attribute="timebars" size="0" value=""/>
</position_info>
<signal_set global_temp="1" name="signal_set: 2024/03/24 14:53:29 #0">
<clock name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|clk_sample" polarity="posedge" tap_mode="classic"/>
<config pipeline_level="1" ram_type="AUTO" reserved_data_nodes="0" reserved_storage_qualifier_nodes="0" reserved_trigger_nodes="0" sample_depth="2048" trigger_in_enable="no" trigger_out_enable="no"/>
<top_entity/> <top_entity/>
<signal_vec> <signal_vec>
<trigger_input_vec> <trigger_input_vec>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[0]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|CASS_REWIND_RECORD" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[1]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|MOTOR_ON" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[2]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[0]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[3]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[1]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[4]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[2]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[5]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[3]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[6]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[4]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[7]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[5]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[8]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[6]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[9]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[7]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|HBLANKING" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[0]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|VBLANKING" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[1]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[2]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[3]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[4]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[5]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[6]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[7]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[8]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[0]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[1]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[2]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[3]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[4]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[5]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[6]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[7]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|look_for_sync" tap_mode="classic"/>
</trigger_input_vec> </trigger_input_vec>
<data_input_vec> <data_input_vec>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[0]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|CASS_REWIND_RECORD" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[1]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|MOTOR_ON" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[2]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[0]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[3]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[1]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[4]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[2]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[5]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[3]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[6]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[4]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[7]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[5]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[8]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[6]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[9]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[7]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|HBLANKING" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[0]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|VBLANKING" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[1]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[2]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[3]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[4]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[5]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[6]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[7]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[8]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[0]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[1]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[2]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[3]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[4]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[5]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[6]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[7]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|look_for_sync" tap_mode="classic"/>
</data_input_vec> </data_input_vec>
<storage_qualifier_input_vec> <storage_qualifier_input_vec>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[0]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|CASS_REWIND_RECORD" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[1]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|MOTOR_ON" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[2]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[0]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[3]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[1]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[4]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[2]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[5]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[3]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[6]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[4]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[7]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[5]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[8]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[6]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[9]" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[7]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|HBLANKING" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[0]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|VBLANKING" tap_mode="classic"/> <wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[1]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[2]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[3]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[4]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[5]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[6]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[7]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[8]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[0]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[1]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[2]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[3]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[4]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[5]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[6]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[7]" tap_mode="classic"/>
<wire name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|look_for_sync" tap_mode="classic"/>
</storage_qualifier_input_vec> </storage_qualifier_input_vec>
</signal_vec> </signal_vec>
<presentation> <presentation>
<unified_setup_data_view> <unified_setup_data_view>
<node is_selected="false" level-0="alt_or" level-1="alt_or" level-2="alt_or" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[9..0]" order="msb_to_lsb" storage-0="alt_or" storage-1="alt_or" storage-2="alt_or" type="combinatorial"> <node data_index="1" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|MOTOR_ON" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="1" tap_mode="classic" trigger_index="1" type="unknown"/>
<node data_index="9" duplicate_name_allowed="false" is_data_input="true" is_node_valid="false" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[9]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="9" tap_mode="classic" trigger_index="9" type="unknown"/> <node data_index="0" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|CASS_REWIND_RECORD" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="0" tap_mode="classic" trigger_index="0" type="unknown"/>
<node data_index="8" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[8]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="8" tap_mode="classic" trigger_index="8" type="unknown"/> <node is_selected="false" level-0="alt_or" level-1="alt_or" level-2="alt_or" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[7..0]" order="msb_to_lsb" storage-0="alt_or" storage-1="alt_or" storage-2="alt_or" type="register">
<node data_index="7" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[7]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="7" tap_mode="classic" trigger_index="7" type="unknown"/> <node data_index="26" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[7]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="26" tap_mode="classic" trigger_index="26" type="unknown"/>
<node data_index="6" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[6]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="6" tap_mode="classic" trigger_index="6" type="unknown"/> <node data_index="25" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[6]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="25" tap_mode="classic" trigger_index="25" type="unknown"/>
<node data_index="5" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[5]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="5" tap_mode="classic" trigger_index="5" type="unknown"/> <node data_index="24" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[5]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="24" tap_mode="classic" trigger_index="24" type="unknown"/>
<node data_index="4" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[4]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="4" tap_mode="classic" trigger_index="4" type="unknown"/> <node data_index="23" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[4]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="23" tap_mode="classic" trigger_index="23" type="unknown"/>
<node data_index="3" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[3]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="3" tap_mode="classic" trigger_index="3" type="unknown"/> <node data_index="22" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[3]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="22" tap_mode="classic" trigger_index="22" type="unknown"/>
<node data_index="2" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[2]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="2" tap_mode="classic" trigger_index="2" type="unknown"/> <node data_index="21" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[2]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="21" tap_mode="classic" trigger_index="21" type="unknown"/>
<node data_index="1" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[1]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="1" tap_mode="classic" trigger_index="1" type="unknown"/> <node data_index="20" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[1]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="20" tap_mode="classic" trigger_index="20" type="unknown"/>
<node data_index="0" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[0]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="0" tap_mode="classic" trigger_index="0" type="unknown"/> <node data_index="19" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[0]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="19" tap_mode="classic" trigger_index="19" type="unknown"/>
</node>
<node data_index="27" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="falling edge" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|look_for_sync" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="27" tap_mode="classic" trigger_index="27" type="unknown"/>
<node is_selected="false" level-0="alt_or" level-1="alt_or" level-2="alt_or" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[8..0]" order="msb_to_lsb" type="register">
<node data_index="18" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[8]" storage_index="18" tap_mode="classic" trigger_index="18" type="unknown"/>
<node data_index="17" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[7]" storage_index="17" tap_mode="classic" trigger_index="17" type="unknown"/>
<node data_index="16" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[6]" storage_index="16" tap_mode="classic" trigger_index="16" type="unknown"/>
<node data_index="15" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[5]" storage_index="15" tap_mode="classic" trigger_index="15" type="unknown"/>
<node data_index="14" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[4]" storage_index="14" tap_mode="classic" trigger_index="14" type="unknown"/>
<node data_index="13" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[3]" storage_index="13" tap_mode="classic" trigger_index="13" type="unknown"/>
<node data_index="12" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[2]" storage_index="12" tap_mode="classic" trigger_index="12" type="unknown"/>
<node data_index="11" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[1]" storage_index="11" tap_mode="classic" trigger_index="11" type="unknown"/>
<node data_index="10" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[0]" storage_index="10" tap_mode="classic" trigger_index="10" type="unknown"/>
</node>
<node is_selected="false" level-0="alt_or" level-1="alt_or" level-2="alt_or" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[7..0]" order="msb_to_lsb" type="register">
<node data_index="9" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[7]" storage_index="9" tap_mode="classic" trigger_index="9" type="unknown"/>
<node data_index="8" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[6]" storage_index="8" tap_mode="classic" trigger_index="8" type="unknown"/>
<node data_index="7" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[5]" storage_index="7" tap_mode="classic" trigger_index="7" type="unknown"/>
<node data_index="6" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[4]" storage_index="6" tap_mode="classic" trigger_index="6" type="unknown"/>
<node data_index="5" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[3]" storage_index="5" tap_mode="classic" trigger_index="5" type="unknown"/>
<node data_index="4" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[2]" storage_index="4" tap_mode="classic" trigger_index="4" type="unknown"/>
<node data_index="3" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[1]" storage_index="3" tap_mode="classic" trigger_index="3" type="unknown"/>
<node data_index="2" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[0]" storage_index="2" tap_mode="classic" trigger_index="2" type="unknown"/>
</node> </node>
<node data_index="10" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="falling edge" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|HBLANKING" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="10" tap_mode="classic" trigger_index="10" type="unknown"/>
<node data_index="11" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="falling edge" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|VBLANKING" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="11" tap_mode="classic" trigger_index="11" type="unknown"/>
</unified_setup_data_view> </unified_setup_data_view>
<data_view> <data_view>
<bus is_selected="false" level-0="alt_or" level-1="alt_or" level-2="alt_or" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[9..0]" order="msb_to_lsb" storage-0="alt_or" storage-1="alt_or" storage-2="alt_or" type="combinatorial"> <net data_index="1" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|MOTOR_ON" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="1" tap_mode="classic" trigger_index="1" type="unknown"/>
<net data_index="9" duplicate_name_allowed="false" is_data_input="true" is_node_valid="false" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[9]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="9" tap_mode="classic" trigger_index="9" type="unknown"/> <net data_index="0" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|CASS_REWIND_RECORD" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="0" tap_mode="classic" trigger_index="0" type="unknown"/>
<net data_index="8" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[8]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="8" tap_mode="classic" trigger_index="8" type="unknown"/> <bus is_selected="false" level-0="alt_or" level-1="alt_or" level-2="alt_or" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[7..0]" order="msb_to_lsb" storage-0="alt_or" storage-1="alt_or" storage-2="alt_or" type="register">
<net data_index="7" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[7]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="7" tap_mode="classic" trigger_index="7" type="unknown"/> <net data_index="26" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[7]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="26" tap_mode="classic" trigger_index="26" type="unknown"/>
<net data_index="6" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[6]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="6" tap_mode="classic" trigger_index="6" type="unknown"/> <net data_index="25" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[6]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="25" tap_mode="classic" trigger_index="25" type="unknown"/>
<net data_index="5" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[5]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="5" tap_mode="classic" trigger_index="5" type="unknown"/> <net data_index="24" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[5]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="24" tap_mode="classic" trigger_index="24" type="unknown"/>
<net data_index="4" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[4]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="4" tap_mode="classic" trigger_index="4" type="unknown"/> <net data_index="23" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[4]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="23" tap_mode="classic" trigger_index="23" type="unknown"/>
<net data_index="3" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[3]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="3" tap_mode="classic" trigger_index="3" type="unknown"/> <net data_index="22" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[3]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="22" tap_mode="classic" trigger_index="22" type="unknown"/>
<net data_index="2" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[2]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="2" tap_mode="classic" trigger_index="2" type="unknown"/> <net data_index="21" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[2]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="21" tap_mode="classic" trigger_index="21" type="unknown"/>
<net data_index="1" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[1]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="1" tap_mode="classic" trigger_index="1" type="unknown"/> <net data_index="20" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[1]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="20" tap_mode="classic" trigger_index="20" type="unknown"/>
<net data_index="0" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[0]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="0" tap_mode="classic" trigger_index="0" type="unknown"/> <net data_index="19" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[0]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="19" tap_mode="classic" trigger_index="19" type="unknown"/>
</bus>
<net data_index="27" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="falling edge" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|look_for_sync" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="27" tap_mode="classic" trigger_index="27" type="unknown"/>
<bus is_selected="false" level-0="alt_or" level-1="alt_or" level-2="alt_or" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[8..0]" order="msb_to_lsb" type="register">
<net data_index="18" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[8]" storage_index="18" tap_mode="classic" trigger_index="18" type="unknown"/>
<net data_index="17" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[7]" storage_index="17" tap_mode="classic" trigger_index="17" type="unknown"/>
<net data_index="16" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[6]" storage_index="16" tap_mode="classic" trigger_index="16" type="unknown"/>
<net data_index="15" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[5]" storage_index="15" tap_mode="classic" trigger_index="15" type="unknown"/>
<net data_index="14" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[4]" storage_index="14" tap_mode="classic" trigger_index="14" type="unknown"/>
<net data_index="13" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[3]" storage_index="13" tap_mode="classic" trigger_index="13" type="unknown"/>
<net data_index="12" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[2]" storage_index="12" tap_mode="classic" trigger_index="12" type="unknown"/>
<net data_index="11" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[1]" storage_index="11" tap_mode="classic" trigger_index="11" type="unknown"/>
<net data_index="10" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[0]" storage_index="10" tap_mode="classic" trigger_index="10" type="unknown"/>
</bus>
<bus is_selected="false" level-0="alt_or" level-1="alt_or" level-2="alt_or" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[7..0]" order="msb_to_lsb" type="register">
<net data_index="9" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[7]" storage_index="9" tap_mode="classic" trigger_index="9" type="unknown"/>
<net data_index="8" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[6]" storage_index="8" tap_mode="classic" trigger_index="8" type="unknown"/>
<net data_index="7" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[5]" storage_index="7" tap_mode="classic" trigger_index="7" type="unknown"/>
<net data_index="6" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[4]" storage_index="6" tap_mode="classic" trigger_index="6" type="unknown"/>
<net data_index="5" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[3]" storage_index="5" tap_mode="classic" trigger_index="5" type="unknown"/>
<net data_index="4" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[2]" storage_index="4" tap_mode="classic" trigger_index="4" type="unknown"/>
<net data_index="3" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[1]" storage_index="3" tap_mode="classic" trigger_index="3" type="unknown"/>
<net data_index="2" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[0]" storage_index="2" tap_mode="classic" trigger_index="2" type="unknown"/>
</bus> </bus>
<net data_index="10" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="falling edge" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|HBLANKING" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="10" tap_mode="classic" trigger_index="10" type="unknown"/>
<net data_index="11" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="falling edge" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|VBLANKING" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="11" tap_mode="classic" trigger_index="11" type="unknown"/>
</data_view> </data_view>
<setup_view> <setup_view>
<bus is_selected="false" level-0="alt_or" level-1="alt_or" level-2="alt_or" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[9..0]" order="msb_to_lsb" storage-0="alt_or" storage-1="alt_or" storage-2="alt_or" type="combinatorial"> <net data_index="1" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|MOTOR_ON" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="1" tap_mode="classic" trigger_index="1" type="unknown"/>
<net data_index="9" duplicate_name_allowed="false" is_data_input="true" is_node_valid="false" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[9]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="9" tap_mode="classic" trigger_index="9" type="unknown"/> <net data_index="0" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|CASS_REWIND_RECORD" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="0" tap_mode="classic" trigger_index="0" type="unknown"/>
<net data_index="8" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[8]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="8" tap_mode="classic" trigger_index="8" type="unknown"/> <bus is_selected="false" level-0="alt_or" level-1="alt_or" level-2="alt_or" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[7..0]" order="msb_to_lsb" storage-0="alt_or" storage-1="alt_or" storage-2="alt_or" type="register">
<net data_index="7" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[7]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="7" tap_mode="classic" trigger_index="7" type="unknown"/> <net data_index="26" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[7]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="26" tap_mode="classic" trigger_index="26" type="unknown"/>
<net data_index="6" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[6]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="6" tap_mode="classic" trigger_index="6" type="unknown"/> <net data_index="25" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[6]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="25" tap_mode="classic" trigger_index="25" type="unknown"/>
<net data_index="5" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[5]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="5" tap_mode="classic" trigger_index="5" type="unknown"/> <net data_index="24" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[5]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="24" tap_mode="classic" trigger_index="24" type="unknown"/>
<net data_index="4" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[4]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="4" tap_mode="classic" trigger_index="4" type="unknown"/> <net data_index="23" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[4]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="23" tap_mode="classic" trigger_index="23" type="unknown"/>
<net data_index="3" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[3]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="3" tap_mode="classic" trigger_index="3" type="unknown"/> <net data_index="22" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[3]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="22" tap_mode="classic" trigger_index="22" type="unknown"/>
<net data_index="2" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[2]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="2" tap_mode="classic" trigger_index="2" type="unknown"/> <net data_index="21" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[2]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="21" tap_mode="classic" trigger_index="21" type="unknown"/>
<net data_index="1" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[1]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="1" tap_mode="classic" trigger_index="1" type="unknown"/> <net data_index="20" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[1]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="20" tap_mode="classic" trigger_index="20" type="unknown"/>
<net data_index="0" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|CCOLOR[0]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="0" tap_mode="classic" trigger_index="0" type="unknown"/> <net data_index="19" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="dont_care" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_data_in[0]" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="19" tap_mode="classic" trigger_index="19" type="unknown"/>
</bus>
<net data_index="27" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="falling edge" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|look_for_sync" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="27" tap_mode="classic" trigger_index="27" type="unknown"/>
<bus is_selected="false" level-0="alt_or" level-1="alt_or" level-2="alt_or" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[8..0]" order="msb_to_lsb" type="register">
<net data_index="18" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[8]" storage_index="18" tap_mode="classic" trigger_index="18" type="unknown"/>
<net data_index="17" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[7]" storage_index="17" tap_mode="classic" trigger_index="17" type="unknown"/>
<net data_index="16" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[6]" storage_index="16" tap_mode="classic" trigger_index="16" type="unknown"/>
<net data_index="15" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[5]" storage_index="15" tap_mode="classic" trigger_index="15" type="unknown"/>
<net data_index="14" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[4]" storage_index="14" tap_mode="classic" trigger_index="14" type="unknown"/>
<net data_index="13" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[3]" storage_index="13" tap_mode="classic" trigger_index="13" type="unknown"/>
<net data_index="12" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[2]" storage_index="12" tap_mode="classic" trigger_index="12" type="unknown"/>
<net data_index="11" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[1]" storage_index="11" tap_mode="classic" trigger_index="11" type="unknown"/>
<net data_index="10" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|buf_address[0]" storage_index="10" tap_mode="classic" trigger_index="10" type="unknown"/>
</bus>
<bus is_selected="false" level-0="alt_or" level-1="alt_or" level-2="alt_or" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[7..0]" order="msb_to_lsb" type="register">
<net data_index="9" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[7]" storage_index="9" tap_mode="classic" trigger_index="9" type="unknown"/>
<net data_index="8" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[6]" storage_index="8" tap_mode="classic" trigger_index="8" type="unknown"/>
<net data_index="7" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[5]" storage_index="7" tap_mode="classic" trigger_index="7" type="unknown"/>
<net data_index="6" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[4]" storage_index="6" tap_mode="classic" trigger_index="6" type="unknown"/>
<net data_index="5" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[3]" storage_index="5" tap_mode="classic" trigger_index="5" type="unknown"/>
<net data_index="4" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[2]" storage_index="4" tap_mode="classic" trigger_index="4" type="unknown"/>
<net data_index="3" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[1]" storage_index="3" tap_mode="classic" trigger_index="3" type="unknown"/>
<net data_index="2" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-1="low" level-2="high" name="emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[0]" storage_index="2" tap_mode="classic" trigger_index="2" type="unknown"/>
</bus> </bus>
<net data_index="10" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="falling edge" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|HBLANKING" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="10" tap_mode="classic" trigger_index="10" type="unknown"/>
<net data_index="11" duplicate_name_allowed="false" is_data_input="true" is_node_valid="true" is_selected="false" is_storage_input="true" is_trigger_input="true" level-0="falling edge" level-1="dont_care" level-2="dont_care" name="emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|VBLANKING" pwr_level-0="dont_care" pwr_level-1="dont_care" pwr_level-2="dont_care" pwr_storage-0="dont_care" pwr_storage-1="dont_care" pwr_storage-2="dont_care" storage-0="dont_care" storage-1="dont_care" storage-2="dont_care" storage_index="11" tap_mode="classic" trigger_index="11" type="unknown"/>
</setup_view> </setup_view>
<trigger_in_editor/> <trigger_in_editor/>
<trigger_out_editor/> <trigger_out_editor/>
</presentation> </presentation>
<trigger CRC="EA9E4B56" attribute_mem_mode="false" gap_record="true" global_temp="1" is_expanded="true" name="trigger: 2024/02/03 00:21:54 #0" position="center" power_up_trigger_mode="false" record_data_gap="true" segment_size="64" storage_mode="off" storage_qualifier_disabled="no" storage_qualifier_port_is_pin="false" storage_qualifier_port_name="auto_stp_external_storage_qualifier" storage_qualifier_port_tap_mode="classic" trigger_type="circular"> <trigger CRC="3B99A6F0" attribute_mem_mode="false" gap_record="true" global_temp="1" name="trigger: 2024/03/24 15:44:31 #0" position="pre" power_up_trigger_mode="false" record_data_gap="true" segment_size="512" storage_mode="off" storage_qualifier_disabled="no" storage_qualifier_port_is_pin="false" storage_qualifier_port_name="auto_stp_external_storage_qualifier" storage_qualifier_port_tap_mode="classic" trigger_type="circular">
<power_up_trigger position="pre" storage_qualifier_disabled="no"/> <power_up_trigger position="pre" storage_qualifier_disabled="no"/>
<events use_custom_flow_control="no"> <events use_custom_flow_control="no">
<level enabled="yes" name="condition1" type="basic">'emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|HBLANKING' == falling edge &amp;&amp; 'emu:emu|coco3fpga:coco3|COCO3VIDEO:MISTER_COCOVID|VBLANKING' == falling edge <level enabled="yes" name="condition1" type="basic">'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|look_for_sync' == falling edge
<power_up enabled="yes"> <power_up enabled="yes">
</power_up><op_node> </power_up>
<op_node>
<op_node left="608" selected="1" top="80" type="Advanced Trigger Level Result"/> <op_node left="608" selected="1" top="80" type="Advanced Trigger Level Result"/>
</op_node> </op_node>
</level> </level>
<level enabled="yes" name="condition2" type="basic"> <level enabled="yes" name="condition2" type="basic">'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[0]' == low &amp;&amp; 'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[1]' == low &amp;&amp; 'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[2]' == low &amp;&amp; 'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[3]' == low &amp;&amp; 'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[4]' == low &amp;&amp; 'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[5]' == low &amp;&amp; 'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[6]' == low &amp;&amp; 'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[7]' == low
<power_up enabled="yes"> <power_up enabled="yes">
</power_up><op_node/> </power_up>
<op_node>
<op_node left="362" top="95" type="Advanced Trigger Level Result"/>
</op_node>
</level> </level>
<level enabled="yes" name="condition3" type="basic"> <level enabled="yes" name="condition3" type="basic">'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[0]' == high &amp;&amp; 'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[1]' == high &amp;&amp; 'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[2]' == high &amp;&amp; 'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[3]' == high &amp;&amp; 'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[4]' == high &amp;&amp; 'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[5]' == high &amp;&amp; 'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[6]' == high &amp;&amp; 'emu:emu|coco3fpga:coco3|Cassette_Write:CoCo3_Cassette_Write|blk_type[7]' == high
<power_up enabled="yes"> <power_up enabled="yes">
</power_up><op_node/> </power_up>
<op_node/>
</level> </level>
<custom_flow_control>
<runtime_configurable comparison_operator="yes" counter_action="no" flag_action="no" logical_operator="yes" numerical_value="yes" state_transition="yes"/>
<flow_expression><![CDATA[state ST1:
trigger;]]>
</flow_expression>
<power_up_flow_expression><![CDATA[state ST1:
trigger;]]>
</power_up_flow_expression>
</custom_flow_control>
</events> </events>
<storage_qualifier_events> <storage_qualifier_events>
<transitional>111111111111 <transitional>1111111111111111111111111111
<pwr_up_transitional>111111111111</pwr_up_transitional> <pwr_up_transitional>1111111111111111111111111111</pwr_up_transitional>
</transitional> </transitional>
<storage_qualifier_level type="basic"> <storage_qualifier_level type="basic">
<power_up> <power_up>
@@ -142,19 +276,12 @@
<op_node/> <op_node/>
</storage_qualifier_level> </storage_qualifier_level>
</storage_qualifier_events> </storage_qualifier_events>
<log>
<data global_temp="1" name="log: Trig @ 2024/03/24 16:48:19 (0:0:12.7 elapsed)" power_up_mode="false" sample_depth="2048" trigger_position="256">11100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000101101001101010101111000000010110100110101010111100000001011010011010101011110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000111000000001110100100111100011100000000111010010011110001110000000011101001001111000Line truncated
<extradata>1111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111T111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111</extradata>
</log>
</trigger> </trigger>
</signal_set> </signal_set>
<position_info>
<single attribute="active tab" value="1"/>
<single attribute="data horizontal scroll position" value="0"/>
<single attribute="data vertical scroll position" value="0"/>
<single attribute="setup horizontal scroll position" value="0"/>
<single attribute="setup vertical scroll position" value="0"/>
<single attribute="zoom level denominator" value="2"/>
<single attribute="zoom level numerator" value="1"/>
<single attribute="zoom offset denominator" value="1"/>
<single attribute="zoom offset numerator" value="261888"/>
</position_info>
</instance> </instance>
<mnemonics/> <mnemonics/>
<static_plugin_mnemonics/> <static_plugin_mnemonics/>
@@ -162,11 +289,12 @@
<single attribute="active instance" value="0"/> <single attribute="active instance" value="0"/>
<single attribute="config widget visible" value="1"/> <single attribute="config widget visible" value="1"/>
<single attribute="data log widget visible" value="1"/> <single attribute="data log widget visible" value="1"/>
<single attribute="hierarchy widget height" value="96"/>
<single attribute="hierarchy widget visible" value="1"/> <single attribute="hierarchy widget visible" value="1"/>
<single attribute="instance widget visible" value="1"/> <single attribute="instance widget visible" value="1"/>
<single attribute="jtag widget visible" value="1"/> <single attribute="jtag widget visible" value="1"/>
<single attribute="lock mode" value="0"/> <single attribute="lock mode" value="0"/>
<multi attribute="column width" size="23" value="34,34,192,74,68,78,95,96,98,98,88,88,110,101,101,101,101,101,101,101,101,107,78"/> <multi attribute="column width" size="23" value="34,34,323,74,68,78,95,96,98,98,88,88,110,101,101,101,101,101,101,101,101,107,78"/>
<multi attribute="frame size" size="2" value="1024,705"/> <multi attribute="frame size" size="2" value="1024,705"/>
<multi attribute="jtag widget size" size="2" value="348,135"/> <multi attribute="jtag widget size" size="2" value="348,135"/>
</global_info> </global_info>
+1
View File
@@ -0,0 +1 @@
`define BUILD_NUMBER "001"
+84
View File
@@ -1,3 +1,87 @@
1. Overlay support for the detection of no rom loading on power up AND misc
debugging. [done]
2. Fix video HSCREEN 4 mode which is used in some demos and rs-232 terminal
programs. [done]
3. Reworked sound output to faithfully emulate the analog muxing in the coco.
[done]
4. Routing RS-232 tx/rx lines to the SNAC port for initial serial debugging
of Fuji-Net interface. [done - untested]
To Do...
1. Add Fuji-Net port.
2. Add Speech / Music cart
3. Fix Castle of Tharoggad
1. Added support for cassette save. To use: A) You have to have a file [anyname.cas]
which is larger than needed. B) Select the file through the UI Menu 'Save
Cassette'. C)Set 'Cass Rwd=0 / Rec=1' to 1. D) Issue your 'CSAVE "NAME"'
E) When done, set 'Cass Rwd=0 / Rec=1' to 0 to complete the write. The file can
now be loaded or copied. Note a dummy file of a specific size can be created in
the MiSTer SSH shell in the /media/fat/games/coco3 with the command:
'truncate -s 65536 tapefileame.cas'. [Note do NOT use over 65536 file length]
2. Fixed serial interrupt [6551] to not be functional on slot 3 [carts].
3. Modification of sys_top.v to override use of USER_IO for HDMI - so it can be used
for logic analyzer debug. This will only occur when `define Config_Debug is
enabled in config.v.
4. Fixed MUGS of powerup issue occurring on some MiSTer units.
5. Fixed incorrect application of GIME_IRQ on legacy interrupts. Fixed race condition
on reading IRQ status vs clearing the interrupt.
6. Improved Castle of Tharoggad. App now loads but locks as the graphics animate. This
change improved mmu usage through to CARTS.
7. Builds now keep track of multiple builds in the same date. It shows as V240512-001 in
the menus. Its also exposed to BASIC and a boot.vhd which can be enabled to autorun is
supplied in the archive to show how it works.
8. Additionally, on the boot.vhd disk, is a program which demonstrated how to load a font -
IBMFONT.BAS. Run it and it maps a font much like the IBM font to the 80 column format.
Also, a file called TESTRTC.BAS pulls the MiSTer RTC values exposed in BASIC to display
a clock.
9. Large improvement in the Timer function. Code closer emulates COCO3 Timer. Fixes
Sliphead cart.
10. In the 20231023 release the wd1773 instances were reduced to 1 for the FDC and one for
the FDC. This saved space but introduced a bug when using multiple drives at the same
time - like a copy command. This change was removed and the copy command works again.
To Do...
1. Add Speech / Music cart
2. Fix Castle of Tharoggad
1. Changed PIA 2 addressing to align with real CoCo3 hardware and end at FF2F.
2. Re-arranged MiSTer drive LUNs to support future auto-boot from SDC drive 0.
3. Added 'Auto Run' feature. You must use slot 2 [SDC]. Take your floppy or HD
and copy it to a file name of 'boot.vhd'. This will be auto mounted to drive 0
on the SDC. In the menu, find a new item Auto Run:. It can be set to No, DOS or
AUTO.BAS. Choosing dos causes the 'DOS' command to be executed on power up. Setting
the option to 'AUTO.BAS' will cause a 'RUN"AUTO' command to be executed upon powerup.
Save your settings to cause the changes to be remembered. The Auto Run system re-arms
upon using the 'Cold Boot' menu item.
4. Fixed MiSTer / CoCo3 interface preventing the joysticks ever reaching the
max value of 63. Specifically '>' was changed to '>=' the DTOA values.
This fixes DonPan and is verified in Diagnostics 2.0.
5. HiRES[3] is used to enable some of the higher resolution graphics modes
Gary Becker designed into CoCo3FPGA, and while these are not fully
supported, the control signals such as HiRES[3] at $FF98 bit 6 affectt
the graphics engine. For some reason Color File II manipulates this bit
and was causing it not to work. This change requires the SG6 extensions
to be enabled to set HiRES[3]. So specifically in the Video Settings
insure CoCo3 LC is set to Yes. Color File II now works properly.
To Do...
1. Add support for cassette save.
2. Add Speech / Music cart
3. Fix Castle of Tharoggod
FYI - If you plan on playing with the build process - there is a new compile time feature
in config.v called CoCo3_Select_GIMEX_RAST. It is inactive and I suggest you leave
it as its is a upcoming change which is not ready.
1. Changed PIA 2 addressing to align with real CoCo3 hardware and end at FF2F. 1. Changed PIA 2 addressing to align with real CoCo3 hardware and end at FF2F.
2. Removal of 16 bit sound extentions as they overlap speach / sound cart. This is 2. Removal of 16 bit sound extentions as they overlap speach / sound cart. This is
accompanied by a rework of the sound mixing to be more correct. accompanied by a rework of the sound mixing to be more correct.
BIN
View File
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
+3 -6
View File
@@ -16,10 +16,11 @@ set_global_assignment -name SYSTEMVERILOG_FILE rtl/coco3fpga.sv
set_global_assignment -name VERILOG_FILE rtl/pll.v set_global_assignment -name VERILOG_FILE rtl/pll.v
set_global_assignment -name VERILOG_FILE rtl/pll/pll_0002.v set_global_assignment -name VERILOG_FILE rtl/pll/pll_0002.v
set_global_assignment -name VERILOG_FILE rtl/cassette.v set_global_assignment -name VERILOG_FILE rtl/cassette.v
set_global_assignment -name SYSTEMVERILOG_FILE rtl/Cassette_Write.sv
set_global_assignment -name VERILOG_FILE rtl/rtc.sv set_global_assignment -name VERILOG_FILE rtl/rtc.sv
set_global_assignment -name VERILOG_FILE rtl/AMW.v set_global_assignment -name VERILOG_FILE rtl/AMW.v
set_global_assignment -name VERILOG_FILE rtl/square_gen.v set_global_assignment -name VERILOG_FILE rtl/square_gen.v
set_global_assignment -name VERILOG_FILE rtl/config.v set_global_assignment -name SYSTEMVERILOG_FILE rtl/config.sv
set_global_assignment -name SYSTEMVERILOG_FILE rtl/fdc.sv set_global_assignment -name SYSTEMVERILOG_FILE rtl/fdc.sv
set_global_assignment -name SYSTEMVERILOG_FILE rtl/sdc.sv set_global_assignment -name SYSTEMVERILOG_FILE rtl/sdc.sv
set_global_assignment -name SYSTEMVERILOG_FILE rtl/sdc_top.sv set_global_assignment -name SYSTEMVERILOG_FILE rtl/sdc_top.sv
@@ -27,16 +28,12 @@ set_global_assignment -name SYSTEMVERILOG_FILE rtl/Auto_Run.sv
set_global_assignment -name SYSTEMVERILOG_FILE rtl/ps2_mouse.v set_global_assignment -name SYSTEMVERILOG_FILE rtl/ps2_mouse.v
set_global_assignment -name SYSTEMVERILOG_FILE rtl/sdram/sdram2.sv set_global_assignment -name SYSTEMVERILOG_FILE rtl/sdram/sdram2.sv
set_global_assignment -name SYSTEMVERILOG_FILE rtl/wd1793.sv set_global_assignment -name SYSTEMVERILOG_FILE rtl/wd1793.sv
set_global_assignment -name SYSTEMVERILOG_FILE rtl/music_speech.sv
set_global_assignment -name SYSTEMVERILOG_FILE rtl/sp0256.vhd
set_global_assignment -name SYSTEMVERILOG_FILE rtl/ym2149_audio.vhd
set_global_assignment -name SYSTEMVERILOG_FILE rtl/Music_Speech_SOC.sv
set_global_assignment -name SYSTEMVERILOG_FILE CoCo3.sv set_global_assignment -name SYSTEMVERILOG_FILE CoCo3.sv
set_global_assignment -name VHDL_FILE rtl/sram/CoCo_ram_6116.vhd
set_global_assignment -name VHDL_FILE rtl/sram/coco_vid_ram_buf.vhd set_global_assignment -name VHDL_FILE rtl/sram/coco_vid_ram_buf.vhd
set_global_assignment -name SYSTEMVERILOG_FILE rtl/coco_mem_fetch.sv set_global_assignment -name SYSTEMVERILOG_FILE rtl/coco_mem_fetch.sv
set_global_assignment -name VERILOG_FILE rtl/EE_Cold_Bt.v set_global_assignment -name VERILOG_FILE rtl/EE_Cold_Bt.v
set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_32K.vhd set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_32K.vhd
set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_8K.vhd set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_8K.vhd
set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_16.vhd set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_16.vhd
set_global_assignment -name VHDL_FILE rtl/OVO.vhd
set_global_assignment -name SDC_FILE rtl/CoCo3FPGA.sdc set_global_assignment -name SDC_FILE rtl/CoCo3FPGA.sdc
+204
View File
@@ -0,0 +1,204 @@
<?xml version="1.0"?>
<instance entity-name="altera_pll" version="17.0" >
<generic name="debug_print_output" value="false" />
<generic name="debug_use_rbc_taf_method" value="false" />
<generic name="device_family" value="Cyclone V" />
<generic name="device" value="5CEBA2F17A7" />
<generic name="gui_device_speed_grade" value="1" />
<generic name="gui_pll_mode" value="Integer-N PLL" />
<generic name="gui_reference_clock_frequency" value="50.0" />
<generic name="gui_channel_spacing" value="0.0" />
<generic name="gui_operation_mode" value="direct" />
<generic name="gui_feedback_clock" value="Global Clock" />
<generic name="gui_fractional_cout" value="32" />
<generic name="gui_dsm_out_sel" value="1st_order" />
<generic name="gui_use_locked" value="true" />
<generic name="gui_en_adv_params" value="false" />
<generic name="gui_number_of_clocks" value="4" />
<generic name="gui_multiply_factor" value="1" />
<generic name="gui_frac_multiply_factor" value="1" />
<generic name="gui_divide_factor_n" value="1" />
<generic name="gui_cascade_counter0" value="false" />
<generic name="gui_output_clock_frequency0" value="114.545454" />
<generic name="gui_divide_factor_c0" value="1" />
<generic name="gui_actual_output_clock_frequency0" value="0 MHz" />
<generic name="gui_ps_units0" value="ps" />
<generic name="gui_phase_shift0" value="0" />
<generic name="gui_phase_shift_deg0" value="0.0" />
<generic name="gui_actual_phase_shift0" value="0" />
<generic name="gui_duty_cycle0" value="50" />
<generic name="gui_cascade_counter1" value="false" />
<generic name="gui_output_clock_frequency1" value="57.272727" />
<generic name="gui_divide_factor_c1" value="1" />
<generic name="gui_actual_output_clock_frequency1" value="0 MHz" />
<generic name="gui_ps_units1" value="ps" />
<generic name="gui_phase_shift1" value="0" />
<generic name="gui_phase_shift_deg1" value="0.0" />
<generic name="gui_actual_phase_shift1" value="0" />
<generic name="gui_duty_cycle1" value="50" />
<generic name="gui_cascade_counter2" value="false" />
<generic name="gui_output_clock_frequency2" value="28.636363" />
<generic name="gui_divide_factor_c2" value="1" />
<generic name="gui_actual_output_clock_frequency2" value="0 MHz" />
<generic name="gui_ps_units2" value="ps" />
<generic name="gui_phase_shift2" value="0" />
<generic name="gui_phase_shift_deg2" value="0.0" />
<generic name="gui_actual_phase_shift2" value="0" />
<generic name="gui_duty_cycle2" value="50" />
<generic name="gui_cascade_counter3" value="false" />
<generic name="gui_output_clock_frequency3" value="14.318181" />
<generic name="gui_divide_factor_c3" value="1" />
<generic name="gui_actual_output_clock_frequency3" value="0 MHz" />
<generic name="gui_ps_units3" value="ps" />
<generic name="gui_phase_shift3" value="0" />
<generic name="gui_phase_shift_deg3" value="0.0" />
<generic name="gui_actual_phase_shift3" value="0" />
<generic name="gui_duty_cycle3" value="50" />
<generic name="gui_cascade_counter4" value="false" />
<generic name="gui_output_clock_frequency4" value="100.0" />
<generic name="gui_divide_factor_c4" value="1" />
<generic name="gui_actual_output_clock_frequency4" value="0 MHz" />
<generic name="gui_ps_units4" value="ps" />
<generic name="gui_phase_shift4" value="0" />
<generic name="gui_phase_shift_deg4" value="0.0" />
<generic name="gui_actual_phase_shift4" value="0" />
<generic name="gui_duty_cycle4" value="50" />
<generic name="gui_cascade_counter5" value="false" />
<generic name="gui_output_clock_frequency5" value="100.0" />
<generic name="gui_divide_factor_c5" value="1" />
<generic name="gui_actual_output_clock_frequency5" value="0 MHz" />
<generic name="gui_ps_units5" value="ps" />
<generic name="gui_phase_shift5" value="0" />
<generic name="gui_phase_shift_deg5" value="0.0" />
<generic name="gui_actual_phase_shift5" value="0" />
<generic name="gui_duty_cycle5" value="50" />
<generic name="gui_cascade_counter6" value="false" />
<generic name="gui_output_clock_frequency6" value="100.0" />
<generic name="gui_divide_factor_c6" value="1" />
<generic name="gui_actual_output_clock_frequency6" value="0 MHz" />
<generic name="gui_ps_units6" value="ps" />
<generic name="gui_phase_shift6" value="0" />
<generic name="gui_phase_shift_deg6" value="0.0" />
<generic name="gui_actual_phase_shift6" value="0" />
<generic name="gui_duty_cycle6" value="50" />
<generic name="gui_cascade_counter7" value="false" />
<generic name="gui_output_clock_frequency7" value="100.0" />
<generic name="gui_divide_factor_c7" value="1" />
<generic name="gui_actual_output_clock_frequency7" value="0 MHz" />
<generic name="gui_ps_units7" value="ps" />
<generic name="gui_phase_shift7" value="0" />
<generic name="gui_phase_shift_deg7" value="0.0" />
<generic name="gui_actual_phase_shift7" value="0" />
<generic name="gui_duty_cycle7" value="50" />
<generic name="gui_cascade_counter8" value="false" />
<generic name="gui_output_clock_frequency8" value="100.0" />
<generic name="gui_divide_factor_c8" value="1" />
<generic name="gui_actual_output_clock_frequency8" value="0 MHz" />
<generic name="gui_ps_units8" value="ps" />
<generic name="gui_phase_shift8" value="0" />
<generic name="gui_phase_shift_deg8" value="0.0" />
<generic name="gui_actual_phase_shift8" value="0" />
<generic name="gui_duty_cycle8" value="50" />
<generic name="gui_cascade_counter9" value="false" />
<generic name="gui_output_clock_frequency9" value="100.0" />
<generic name="gui_divide_factor_c9" value="1" />
<generic name="gui_actual_output_clock_frequency9" value="0 MHz" />
<generic name="gui_ps_units9" value="ps" />
<generic name="gui_phase_shift9" value="0" />
<generic name="gui_phase_shift_deg9" value="0.0" />
<generic name="gui_actual_phase_shift9" value="0" />
<generic name="gui_duty_cycle9" value="50" />
<generic name="gui_cascade_counter10" value="false" />
<generic name="gui_output_clock_frequency10" value="100.0" />
<generic name="gui_divide_factor_c10" value="1" />
<generic name="gui_actual_output_clock_frequency10" value="0 MHz" />
<generic name="gui_ps_units10" value="ps" />
<generic name="gui_phase_shift10" value="0" />
<generic name="gui_phase_shift_deg10" value="0.0" />
<generic name="gui_actual_phase_shift10" value="0" />
<generic name="gui_duty_cycle10" value="50" />
<generic name="gui_cascade_counter11" value="false" />
<generic name="gui_output_clock_frequency11" value="100.0" />
<generic name="gui_divide_factor_c11" value="1" />
<generic name="gui_actual_output_clock_frequency11" value="0 MHz" />
<generic name="gui_ps_units11" value="ps" />
<generic name="gui_phase_shift11" value="0" />
<generic name="gui_phase_shift_deg11" value="0.0" />
<generic name="gui_actual_phase_shift11" value="0" />
<generic name="gui_duty_cycle11" value="50" />
<generic name="gui_cascade_counter12" value="false" />
<generic name="gui_output_clock_frequency12" value="100.0" />
<generic name="gui_divide_factor_c12" value="1" />
<generic name="gui_actual_output_clock_frequency12" value="0 MHz" />
<generic name="gui_ps_units12" value="ps" />
<generic name="gui_phase_shift12" value="0" />
<generic name="gui_phase_shift_deg12" value="0.0" />
<generic name="gui_actual_phase_shift12" value="0" />
<generic name="gui_duty_cycle12" value="50" />
<generic name="gui_cascade_counter13" value="false" />
<generic name="gui_output_clock_frequency13" value="100.0" />
<generic name="gui_divide_factor_c13" value="1" />
<generic name="gui_actual_output_clock_frequency13" value="0 MHz" />
<generic name="gui_ps_units13" value="ps" />
<generic name="gui_phase_shift13" value="0" />
<generic name="gui_phase_shift_deg13" value="0.0" />
<generic name="gui_actual_phase_shift13" value="0" />
<generic name="gui_duty_cycle13" value="50" />
<generic name="gui_cascade_counter14" value="false" />
<generic name="gui_output_clock_frequency14" value="100.0" />
<generic name="gui_divide_factor_c14" value="1" />
<generic name="gui_actual_output_clock_frequency14" value="0 MHz" />
<generic name="gui_ps_units14" value="ps" />
<generic name="gui_phase_shift14" value="0" />
<generic name="gui_phase_shift_deg14" value="0.0" />
<generic name="gui_actual_phase_shift14" value="0" />
<generic name="gui_duty_cycle14" value="50" />
<generic name="gui_cascade_counter15" value="false" />
<generic name="gui_output_clock_frequency15" value="100.0" />
<generic name="gui_divide_factor_c15" value="1" />
<generic name="gui_actual_output_clock_frequency15" value="0 MHz" />
<generic name="gui_ps_units15" value="ps" />
<generic name="gui_phase_shift15" value="0" />
<generic name="gui_phase_shift_deg15" value="0.0" />
<generic name="gui_actual_phase_shift15" value="0" />
<generic name="gui_duty_cycle15" value="50" />
<generic name="gui_cascade_counter16" value="false" />
<generic name="gui_output_clock_frequency16" value="100.0" />
<generic name="gui_divide_factor_c16" value="1" />
<generic name="gui_actual_output_clock_frequency16" value="0 MHz" />
<generic name="gui_ps_units16" value="ps" />
<generic name="gui_phase_shift16" value="0" />
<generic name="gui_phase_shift_deg16" value="0.0" />
<generic name="gui_actual_phase_shift16" value="0" />
<generic name="gui_duty_cycle16" value="50" />
<generic name="gui_cascade_counter17" value="false" />
<generic name="gui_output_clock_frequency17" value="100.0" />
<generic name="gui_divide_factor_c17" value="1" />
<generic name="gui_actual_output_clock_frequency17" value="0 MHz" />
<generic name="gui_ps_units17" value="ps" />
<generic name="gui_phase_shift17" value="0" />
<generic name="gui_phase_shift_deg17" value="0.0" />
<generic name="gui_actual_phase_shift17" value="0" />
<generic name="gui_duty_cycle17" value="50" />
<generic name="gui_pll_auto_reset" value="Off" />
<generic name="gui_pll_bandwidth_preset" value="Auto" />
<generic name="gui_en_reconf" value="false" />
<generic name="gui_en_dps_ports" value="false" />
<generic name="gui_en_phout_ports" value="false" />
<generic name="gui_phout_division" value="1" />
<generic name="gui_mif_generate" value="false" />
<generic name="gui_enable_mif_dps" value="false" />
<generic name="gui_dps_cntr" value="C0" />
<generic name="gui_dps_num" value="1" />
<generic name="gui_dps_dir" value="Positive" />
<generic name="gui_refclk_switch" value="false" />
<generic name="gui_refclk1_frequency" value="100.0" />
<generic name="gui_switchover_mode" value="Automatic Switchover" />
<generic name="gui_switchover_delay" value="0" />
<generic name="gui_active_clk" value="false" />
<generic name="gui_clk_bad" value="false" />
<generic name="gui_enable_cascade_out" value="false" />
<generic name="gui_cascade_outclk_index" value="0" />
<generic name="gui_enable_cascade_in" value="false" />
<generic name="gui_pll_cascading_mode" value="Create an adjpllin signal to connect with an upstream PLL" />
</instance>
Binary file not shown.
Binary file not shown.
Binary file not shown.
+2 -2
View File
@@ -233,7 +233,7 @@ begin
st_2: st_2:
begin begin
if (timer[18] == 1'b1) // 300ms time passed if (timer[17] == 1'b1) // 300ms time passed
begin begin
key_up_down <= RELEASE_KEY; key_up_down <= RELEASE_KEY;
state <= st_3; state <= st_3;
@@ -242,7 +242,7 @@ begin
st_3: st_3:
begin begin
if (timer[18] == 1'b0) // 300ms time passed if (timer[17] == 1'b0) // 300ms time passed
begin begin
shift <= 1'b0; shift <= 1'b0;
timer_enable <= 1'b0; timer_enable <= 1'b0;
+533
View File
@@ -0,0 +1,533 @@
////////////////////////////////////////////////////////////////////////////////
// Project Name: CoCo3FPGA Version 5.x.x
// File Name: Cassette_Write.sv
//
// CoCo3 in an FPGA
//
////////////////////////////////////////////////////////////////////////////////
//
////////////////////////////////////////////////////////////////////////////////
//
// Color Computer 3 compatible system on a chip
//
//
// Copyright (c) 2008 Gary Becker ([email protected])
//
// All rights reserved
//
// Redistribution and use in source and synthezised forms, with or without
// modification, are permitted provided that the following conditions are met:
//
// Redistributions of source code must retain the above copyright notice,
// this list of conditions and the following disclaimer.
//
// Redistributions in synthesized form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the distribution.
//
// Neither the name of the author nor the names of other contributors may
// be used to endorse or promote products derived from this software without
// specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
// THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
// PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
// CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
// POSSIBILITY OF SUCH DAMAGE.
//
// Please report bugs to the author, but before you do so, please
// make sure that this is not a derivative work and that
// you have the latest version of this file.
//
//
////////////////////////////////////////////////////////////////////////////////
// Stan Hodge
//
// Cassette_Write by Stan Hodge 03/18/24
////////////////////////////////////////////////////////////////////////////////
module Cassette_Write(
input RESET_N,
input CLK,
input CLK_1_78,
input CASS_REWIND_RECORD,
input MOTOR_ON,
input [5:0] DTOA_CODE,
// SD block level interface
input img_mounted, // signaling that new image has been mounted
input img_readonly, // mounted as read only. valid only for active bit in img_mounted
input [63:0] img_size, // size of image in bytes.
output [31:0] sd_lba,
output [5:0] sd_blk_cnt, // number of blocks-1, total size ((sd_blk_cnt+1)*(1<<(BLKSZ+7))) must be <= 16384!
output reg sd_rd,
output reg sd_wr,
input sd_ack,
// SD byte level access. Signals for 2-PORT altsyncram.
input [8:0] sd_buff_addr,
input [7:0] sd_buff_dout,
output [7:0] sd_buff_din,
input sd_buff_wr
);
// Create 16x sample clock for the 2400 Baud rate...
// ~26us based on 1.78Mhz [562 ns]- divide by 46....
// Generate 1.78 Mhz [enable] GP clk
reg clk_sample;
reg [5:0] clk_sample_ctr;
localparam Divide_Rate = 6'd45;
always @ (negedge CLK or negedge RESET_N)
begin
if(!RESET_N)
begin
clk_sample <= 1'b0;
clk_sample_ctr <= 6'b000000;
end
else
begin
clk_sample <= 1'b0;
if (CLK_1_78)
begin
clk_sample_ctr <= clk_sample_ctr + 1'b1;
if (clk_sample_ctr == Divide_Rate)
begin
clk_sample <= 1'b1;
clk_sample_ctr <= 6'b000000;
end
end
end
end
// Mounted SD Image [for the cass]
// This is not used and only here for completeness
//reg drive_wp;
//reg [31:0] drive_size;
//always @(negedge img_mounted)
//begin
// drive_wp <= img_readonly;
// drive_size <= img_size[31:0]; //Size / 256 on [31:8]
//end
// Set to 1 512 byte block per r/w
assign sd_blk_cnt = 6'd0;
// Byte Receiver
reg [15:0] incomming_reg;
reg [5:0] bit_time;
reg [2:0] bit_count;
reg wave_negative;
localparam time_out = 6'h3f;
localparam wave_zero_level = 6'd32;
localparam bit_time_1 = 6'd22;
localparam sync = 15'b0111_1000_1010_101; // Pre shift $553C [L -> R]
localparam sync_proper = 8'h3C;
localparam leader = 8'h55;
localparam pre_rollover = 9'h1FF;
localparam rollover = 9'h000;
reg byte_clk;
reg look_for_sync;
reg flush_end, flush_end_que;
reg sd_hold;
reg pre_roll;
reg [7:0] blk_type;
reg [7:0] protocol_data_count;
reg gap;
// Buffer interface
wire [8:0] buf_address;
wire [7:0] buf_data_in;
wire [7:0] buf_data_out;
wire buf_write;
// State Mach states
localparam st_beg0 = 4'd0;
localparam st_start = 4'd1;
localparam st_st1 = 4'd2;
localparam st_st2 = 4'd3;
localparam st_wr = 4'd4;
localparam st_wr1 = 4'd5;
reg [3:0] st_state;
reg [3:0] state_stack;
localparam p_sync = 3'd0;
localparam p_blk_type = 3'd1;
localparam p_len = 3'd2;
localparam p_dta = 3'd3;
localparam p_cksum = 3'd4;
reg [2:0] p_state;
localparam sd_wr_st = 2'd0;
localparam sd_wr_st1 = 2'd1;
localparam sd_wr_st2 = 2'd2;
reg [1:0] sd_wr_state;
always @ (negedge CLK or negedge RESET_N)
begin
if(!RESET_N)
begin
buf_address <= 9'b000000000;
byte_clk <= 1'b0;
bit_count <= 3'b000;
incomming_reg <= 16'h0000;
bit_time <= 6'b000000;
wave_negative <= 1'b0;
look_for_sync <= 1'b1;
buf_write <= 1'b0;
st_state <= st_beg0;
p_state <= p_sync;
flush_end <= 1'b0;
flush_end_que <= 1'b0;
sd_lba <= 32'd0;
sd_wr <= 1'b0;
sd_rd <= 1'b0;
sd_wr_state <= sd_wr_st;
sd_hold <= 1'b0;
pre_roll <= 1'b0;
gap <= 1'b0;
end
else
begin
// Synchronus Clears
if (!MOTOR_ON)
begin
// Receiver Resets
byte_clk <= 1'b0;
bit_count <= 3'b000;
incomming_reg <= 16'h0000;
bit_time <= 6'b000000;
wave_negative <= 1'b0;
look_for_sync <= 1'b1;
end
if (!CASS_REWIND_RECORD)
begin
// Eject Tape
byte_clk <= 1'b0;
bit_count <= 3'b000;
incomming_reg <= 16'h0000;
bit_time <= 6'b000000;
wave_negative <= 1'b0;
look_for_sync <= 1'b1;
st_state <= st_beg0;
p_state <= p_sync;
buf_write <= 1'b0;
flush_end <= 1'b0;
flush_end_que <= 1'b0;
sd_lba <= 32'd0;
sd_wr <= 1'b0;
sd_rd <= 1'b0;
sd_wr_state <= sd_wr_st;
sd_hold <= 1'b0;
pre_roll <= 1'b0;
gap <= 1'b0;
end
byte_clk <= 1'b0;
// 2400/1200 baud receiver
if (clk_sample)
begin
if (DTOA_CODE < wave_zero_level)
wave_negative <= 1'b1;
else
wave_negative <= 1'b0;
bit_time <= bit_time + 1'b1;
// Zero crossing detect
if ((DTOA_CODE >= wave_zero_level) && wave_negative)
begin
// Initially we are not collecting the leader bytes just collecting them and
// waiting for the sync $3C55. The write to file stage will automatically
// write the 128 leader bytes befor we start transfering data.
if (!look_for_sync)
begin
bit_count <= bit_count + 1'b1;
if (bit_count == 3'b111)
byte_clk <= 1'b1;
end
// Shift
incomming_reg[14:0] <= incomming_reg[15:1];
if (bit_time < bit_time_1)
incomming_reg[15] <= 1'b1;
else
begin
incomming_reg[15] <= 1'b0;
if (incomming_reg[15:1] == sync)
begin
look_for_sync <= 1'b0;
byte_clk <= 1'b1;
end
end
bit_time <= 6'b000000;
end
end
// Normal clocking starts here
case(st_state)
st_beg0:
begin
// When we start we write 128 bytes of leader to the buffer
// before we start with the protocol stuff
if (MOTOR_ON)
begin
buf_address <= 9'b000000000;
buf_data_in <= leader;
protocol_data_count <= 8'h80; // We will use this to count the 128 bytes
st_state <= st_start;
end
end
st_start:
begin
state_stack <= st_start; // We come back here
st_state <= st_wr; // Write a byte
protocol_data_count <= protocol_data_count - 1'b1;
if (protocol_data_count == 8'h00) // 128 bytes
begin
st_state <= st_st1; // No, don't write any more - were done
end
end
st_st1:
begin
if (byte_clk)
begin
case(p_state)
p_sync:
begin
if (incomming_reg[15:8] == sync_proper)
begin
buf_data_in <= incomming_reg[15:8];
state_stack <= st_st1; // We come back here
st_state <= st_wr; // Write a byte
p_state <= p_blk_type;
end
end
p_blk_type:
begin
buf_data_in <= incomming_reg[15:8];
blk_type <= incomming_reg[15:8];
state_stack <= st_st1; // We come back here
st_state <= st_wr; // Write a byte
p_state <= p_len;
end
p_len:
begin
buf_data_in <= incomming_reg[15:8];
protocol_data_count <= incomming_reg[15:8];
state_stack <= st_st1; // We come back here
st_state <= st_wr; // Write a byte
if (incomming_reg[15:8] == 8'h00)
p_state <= p_cksum;
else
p_state <= p_dta;
end
p_dta:
begin
buf_data_in <= incomming_reg[15:8];
protocol_data_count <= protocol_data_count - 1'b1;
state_stack <= st_st1; // We come back here
st_state <= st_wr; // Write a byte
p_state <= p_dta;
if ((blk_type == 8'h00) & (protocol_data_count == 8'h05) & (incomming_reg[15:8] == 8'hff))
gap <= 1'b1;
if (protocol_data_count == 8'h01)
p_state <= p_cksum;
end
p_cksum:
begin
buf_data_in <= incomming_reg[15:8];
look_for_sync <= 1'b1;
if (blk_type == 8'hff)
begin
flush_end_que <= 1'b1;
state_stack <= st_st1; // We come back here [close it]
end
else
state_stack <= st_st2; // We come back here [next block]
st_state <= st_wr; // Write a byte
p_state <= p_sync;
end
default:;
endcase
end
end
st_st2:
begin
buf_data_in <= leader;
if ((blk_type == 8'h00) || gap)
protocol_data_count <= 8'h80; // We will use this to count the 128 bytes
else
protocol_data_count <= 8'h02; // We will use this to count the 2 bytes
st_state <= st_start; // No, don't write any more - were done
end
// Perform the byte writes to the buffer
// This acts like a sub routine....
st_wr:
begin
if (!sd_hold)
begin
buf_write <= 1'b1;
st_state <= st_wr1;
end
end
st_wr1:
begin
buf_address <= buf_address + 1'b1;
buf_write <= 1'b0;
flush_end <= flush_end_que;
flush_end_que <= 1'b0;
st_state <= state_stack;
end
default:;
endcase
// Handle SD buf clear
case(sd_wr_state)
sd_wr_st:
begin
if (buf_address == pre_rollover)
pre_roll <= 1'b1; // Stop writing to buffer
if ((buf_address == rollover) & pre_roll) // If buffer full - write it to SD
begin
pre_roll <= 1'b0;
sd_wr <= 1'b1;
sd_wr_state <= sd_wr_st1;
sd_hold <= 1'b1; // Hold writes
end
if (flush_end) // Write remainder of the buffer at th end...
begin
sd_wr <= 1'b1;
flush_end <= 1'b0;
sd_hold <= 1'b1;
sd_wr_state <= sd_wr_st1;
end
end
sd_wr_st1:
begin
if (sd_ack)
begin
sd_wr <= 1'b0;
sd_wr_state <= sd_wr_st2;
end
end
sd_wr_st2:
begin
if (!sd_ack)
begin
sd_hold <= 1'b0;
sd_lba <= sd_lba + 1'b1;
sd_wr_state <= sd_wr_st;
end
end
default:;
endcase
end
end
cass_dpram cas_wr_buff
(
.clock(CLK),
.address_a(sd_buff_addr),
.data_a(sd_buff_dout),
.wren_a(sd_buff_wr),
.q_a(sd_buff_din),
.address_b(buf_address),
.data_b(buf_data_in),
.wren_b(buf_write),
.q_b(buf_data_out)
);
endmodule
module cass_dpram
(
input clock,
input [8:0] address_a,
input [7:0] data_a,
input wren_a,
output reg [7:0] q_a,
input [8:0] address_b,
input [7:0] data_b,
input wren_b,
output reg [7:0] q_b
);
logic [7:0] ram[0:511];
always_ff@(posedge clock) begin
if(wren_a) begin
ram[address_a] <= data_a;
q_a <= data_a;
end else begin
q_a <= ram[address_a];
end
end
always_ff@(posedge clock) begin
if(wren_b) begin
ram[address_b] <= data_b;
q_b <= data_b;
end else begin
q_b <= ram[address_b];
end
end
endmodule
+1
View File
@@ -5,6 +5,7 @@ create_clock -period 1000.000 -name img_mounted[2] [get_nodes emu:emu|hps_io:hps
create_clock -period 1000.000 -name img_mounted[1] [get_nodes emu:emu|hps_io:hps_io|img_mounted[1]] create_clock -period 1000.000 -name img_mounted[1] [get_nodes emu:emu|hps_io:hps_io|img_mounted[1]]
create_clock -period 1000.000 -name img_mounted[0] [get_nodes emu:emu|hps_io:hps_io|img_mounted[0]] create_clock -period 1000.000 -name img_mounted[0] [get_nodes emu:emu|hps_io:hps_io|img_mounted[0]]
create_clock -period 1000.000 -name RESET_N [get_nodes emu:emu|coco3fpga:coco3|RESET_N] create_clock -period 1000.000 -name RESET_N [get_nodes emu:emu|coco3fpga:coco3|RESET_N]
create_clock -period 1000.000 -name NMISample2 [get_nodes emu:emu|coco3fpga:coco3|mc6809x:GLBCPU09|NMISample2]
#set_false_path -from [get_nodes sysmem_lite:sysmem|sysmem_HPS_fpga_interfaces:fpga_interfaces|clocks_resets~FF_4365] #set_false_path -from [get_nodes sysmem_lite:sysmem|sysmem_HPS_fpga_interfaces:fpga_interfaces|clocks_resets~FF_4365]
#create_clock -period 17.46 -name PH_2 [get_nodes emu:emu|coco3fpga:coco3|PH_2_RAW] #create_clock -period 17.46 -name PH_2 [get_nodes emu:emu|coco3fpga:coco3|PH_2_RAW]
#create_clock -period 1000.000 -name CLK_6551[4] [get_nodes emu:emu|coco3fpga:coco3|CLK_6551[4]] #create_clock -period 1000.000 -name CLK_6551[4] [get_nodes emu:emu|coco3fpga:coco3|CLK_6551[4]]
+15 -2
View File
@@ -55,6 +55,7 @@
module EE_Cold_Bt( module EE_Cold_Bt(
input CLK, input CLK,
input RESET,
input Display_EE, // from MISTer subsystem input Display_EE, // from MISTer subsystem
input Cold_Boot, // from MISTer subsystem input Cold_Boot, // from MISTer subsystem
@@ -106,9 +107,20 @@ assign Start_Display_EE = ((Display_EE == 1'b1) & (Display_EE_D == 1'b0));
assign Start_Cold_Boot = ((Cold_Boot == 1'b1) & (Cold_Boot_D == 1'b0)); assign Start_Cold_Boot = ((Cold_Boot == 1'b1) & (Cold_Boot_D == 1'b0));
always @(posedge CLK) always @ (posedge CLK or posedge RESET)
begin
if(RESET)
begin
Display_EE_D <= 1'b0;
Cold_Boot_D <= 1'b0;
EE <= 1'b1;
N_RESET <= 1'b1;
prog <= 48'h000000000000;
next_instruction <= 1'b0;
timer <= 24'h000000;
end
else
begin begin
Display_EE_D <= Display_EE; Display_EE_D <= Display_EE;
Cold_Boot_D <= Cold_Boot; Cold_Boot_D <= Cold_Boot;
@@ -206,5 +218,6 @@ begin
endcase endcase
end end
end
endmodule endmodule
+82 -29
View File
@@ -88,6 +88,7 @@ HSYNC_N,
VSYNC_N, VSYNC_N,
HBLANKING, HBLANKING,
VBLANKING, VBLANKING,
VBLANK_PRIME,
// RAM / Buffer // RAM / Buffer
RAM_ADDRESS, RAM_ADDRESS,
@@ -124,13 +125,21 @@ HBORDER,
VBORDER, VBORDER,
HBORDER_INT, HBORDER_INT,
VBORDER_INT, VBORDER_INT,
art art,
PIXEL_COUNT,
LINE
); );
input MASTER_CLK; input MASTER_CLK;
input PIX_CLK; output PIX_CLK;
reg PIX_CLK;
input RESET_N; input RESET_N;
output [10:0] PIXEL_COUNT;
reg [10:0] PIXEL_COUNT;
output [9:0] LINE;
reg [9:0] LINE;
output [9:0] COLOR; output [9:0] COLOR;
reg [9:0] COLOR; reg [9:0] COLOR;
output HSYNC_N; output HSYNC_N;
@@ -138,6 +147,8 @@ reg HSYNC_N;
output VSYNC_N; output VSYNC_N;
output HBLANKING; output HBLANKING;
reg HBLANKING; reg HBLANKING;
output VBLANK_PRIME;
reg VBLANK_PRIME;
output VBLANKING; output VBLANKING;
reg VBLANKING; reg VBLANKING;
@@ -180,10 +191,8 @@ reg VBORDER_INT;
input [1:0] art; input [1:0] art;
//reg HBLANKING; //reg HBLANKING;
reg [9:0] LINE;
reg [3:0] VLPR; reg [3:0] VLPR;
//reg [3:0] COCO_VLPR; //reg [3:0] COCO_VLPR;
reg [10:0] PIXEL_COUNT;
reg [15:0] CHAR_LATCH_0_TMP; reg [15:0] CHAR_LATCH_0_TMP;
reg [15:0] CHAR_LATCH_1_TMP; reg [15:0] CHAR_LATCH_1_TMP;
reg [15:0] CHAR_LATCH_2_TMP; reg [15:0] CHAR_LATCH_2_TMP;
@@ -237,7 +246,7 @@ wire [8:0] BUF_ADD_BASE;
//reg [353:0] VSYNC_DELAY; //reg [353:0] VSYNC_DELAY;
//reg VBLANKING; //reg VBLANKING;
//wire [3:0] SG_VLPR; //wire [3:0] SG_VLPR;
reg [139:0] VSYNC_DELAY; //reg [139:0] VSYNC_DELAY;
reg VBORDER; reg VBORDER;
reg VSYNC_FLAG; reg VSYNC_FLAG;
reg HBORDER_DELAY; reg HBORDER_DELAY;
@@ -1504,21 +1513,40 @@ assign PIXEL_X =
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b11110101001) ? {6'h00,CHAR_LATCH_0[9:8]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b11110101001) ? {6'h00,CHAR_LATCH_0[9:8]}:
//4 Color 512/640 = 640/4 = 160 //4 Color 512/640 = 640/4 = 160
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b00000101101) ? {6'h00,CHAR_LATCH_0[7:6]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b00010101101) ? {6'h00,CHAR_LATCH_0[7:6]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b00100101101) ? {6'h00,CHAR_LATCH_0[5:4]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b00110101101) ? {6'h00,CHAR_LATCH_0[5:4]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b01000101101) ? {6'h00,CHAR_LATCH_0[3:2]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b01010101101) ? {6'h00,CHAR_LATCH_0[3:2]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b01100101101) ? {6'h00,CHAR_LATCH_0[1:0]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b01110101101) ? {6'h00,CHAR_LATCH_0[1:0]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b10000101101) ? {6'h00,CHAR_LATCH_0[15:14]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b10010101101) ? {6'h00,CHAR_LATCH_0[15:14]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b10100101101) ? {6'h00,CHAR_LATCH_0[13:12]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b10110101101) ? {6'h00,CHAR_LATCH_0[13:12]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b11000101101) ? {6'h00,CHAR_LATCH_0[11:10]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b11010101101) ? {6'h00,CHAR_LATCH_0[11:10]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b11100101101) ? {6'h00,CHAR_LATCH_0[9:8]}:
//({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b11110101101) ? {6'h00,CHAR_LATCH_1[9:8]}:
// Update by G. Becker on 4/18/26 to fix HSCREEN 4 mode (640 x 192) 4 color mode.
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b00000101101) ? {6'h00,CHAR_LATCH_0[7:6]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b00000101101) ? {6'h00,CHAR_LATCH_0[7:6]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b00010101101) ? {6'h00,CHAR_LATCH_0[7:6]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b00010101101) ? {6'h00,CHAR_LATCH_0[5:4]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b00100101101) ? {6'h00,CHAR_LATCH_0[5:4]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b00100101101) ? {6'h00,CHAR_LATCH_0[3:2]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b00110101101) ? {6'h00,CHAR_LATCH_0[5:4]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b00110101101) ? {6'h00,CHAR_LATCH_0[1:0]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b01000101101) ? {6'h00,CHAR_LATCH_0[3:2]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b01000101101) ? {6'h00,CHAR_LATCH_0[15:14]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b01010101101) ? {6'h00,CHAR_LATCH_0[3:2]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b01010101101) ? {6'h00,CHAR_LATCH_0[13:12]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b01100101101) ? {6'h00,CHAR_LATCH_0[1:0]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b01100101101) ? {6'h00,CHAR_LATCH_0[11:10]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b01110101101) ? {6'h00,CHAR_LATCH_0[1:0]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b01110101101) ? {6'h00,CHAR_LATCH_0[9:8]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b10000101101) ? {6'h00,CHAR_LATCH_0[15:14]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b10000101101) ? {6'h00,CHAR_LATCH_1[7:6]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b10010101101) ? {6'h00,CHAR_LATCH_0[15:14]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b10010101101) ? {6'h00,CHAR_LATCH_1[5:4]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b10100101101) ? {6'h00,CHAR_LATCH_0[13:12]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b10100101101) ? {6'h00,CHAR_LATCH_1[3:2]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b10110101101) ? {6'h00,CHAR_LATCH_0[13:12]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b10110101101) ? {6'h00,CHAR_LATCH_1[1:0]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b11000101101) ? {6'h00,CHAR_LATCH_0[11:10]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b11000101101) ? {6'h00,CHAR_LATCH_1[15:14]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b11010101101) ? {6'h00,CHAR_LATCH_0[11:10]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b11010101101) ? {6'h00,CHAR_LATCH_1[13:12]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b11100101101) ? {6'h00,CHAR_LATCH_0[9:8]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b11100101101) ? {6'h00,CHAR_LATCH_1[11:10]}:
({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b11110101101) ? {6'h00,CHAR_LATCH_1[9:8]}: ({PIXEL_COUNT[3:0],COCO1,BP,HRES[3:1],CRES} == 11'b11110101101) ? {6'h00,CHAR_LATCH_1[9:8]}:
//16 Color 32/40 = 40/2 = 20 //16 Color 32/40 = 40/2 = 20
@@ -1785,6 +1813,15 @@ HBlanking has to be 1 for border
HBORDER has to be 1 for main display HBORDER has to be 1 for main display
HBlanking has to be 0 for main display HBlanking has to be 0 for main display
******************************************************************************/ ******************************************************************************/
always @ (posedge MASTER_CLK)
begin
reg [1:0] div;
PIX_CLK <= 1'b0;
div <= div + 1'b1;
if ((div == 2'd1) || (div == 2'd2))
PIX_CLK <= 1'b1;
end
always @ (negedge MASTER_CLK) always @ (negedge MASTER_CLK)
if(PIX_CLK == 1'b0 && PIX_CLK_DELAY == 1'b1) if(PIX_CLK == 1'b0 && PIX_CLK_DELAY == 1'b1)
begin begin
@@ -1820,6 +1857,10 @@ always @ (negedge MASTER_CLK)
11'd724: // End of right border 720 + 44 - 1 (+ 64) start of back porch 11'd724: // End of right border 720 + 44 - 1 (+ 64) start of back porch
begin begin
HBORDER <= 1'b0; // 736 - 28 HBORDER <= 1'b0; // 736 - 28
if (LINE == 9'd262)
VBLANK_PRIME <= 1'b0;
if (LINE == 9'd5)
VBLANK_PRIME <= 1'b1;
PIXEL_COUNT <= 11'd725; PIXEL_COUNT <= 11'd725;
end end
@@ -1827,15 +1868,25 @@ always @ (negedge MASTER_CLK)
// Adjust HSYNC here // Adjust HSYNC here
**************************************************************************************/ **************************************************************************************/
// Width from 87 GIME 5.08 uS = 73 clocks // Width from 87 GIME 5.08 uS = 73 clocks
11'd751: // 824 - 751 = 73 (approx 5.09 uS) // 11'd751: // 824 - 751 = 73 (approx 5.09 uS)
// begin
// HSYNC_N <= 1'b0; // Turn on Sync
// PIXEL_COUNT <= 11'd752;
// end
// 11'd810: // End of SYNC start of front porch 804 + 80 - 1, End of Sync to Video = 167 816 + 167 =
// begin
// HSYNC_N <= 1'b1; // SYNC OFF
// PIXEL_COUNT <= 11'd811;
// end
11'd752: // 824 - 751 = 73 (approx 5.09 uS)
begin begin
HSYNC_N <= 1'b0; // Turn on Sync HSYNC_N <= 1'b0; // Turn on Sync
PIXEL_COUNT <= 11'd752; PIXEL_COUNT <= 11'd753;
end end
11'd810: // End of SYNC start of front porch 804 + 80 - 1, End of Sync to Video = 167 816 + 167 = 11'd811: // End of SYNC start of front porch 804 + 80 - 1, End of Sync to Video = 167 816 + 167 =
begin begin
HSYNC_N <= 1'b1; // SYNC OFF HSYNC_N <= 1'b1; // SYNC OFF
PIXEL_COUNT <= 11'd811; PIXEL_COUNT <= 11'd812;
end end
/************************************************************************************** /**************************************************************************************
* End of HSYNC adjustment * End of HSYNC adjustment
@@ -1917,12 +1968,14 @@ assign SG6 = VLPR[3:2];
* Generate clock for VSYNC_N by * Generate clock for VSYNC_N by
* Delaying VSYNC_FLAG by 137 pixels * Delaying VSYNC_FLAG by 137 pixels
*************************************/ *************************************/
assign VSYNC_N = VSYNC_DELAY[137]; //assign VSYNC_N = VSYNC_DELAY[137];
always @ (negedge MASTER_CLK) //always @ (negedge MASTER_CLK)
if(PIX_CLK == 1'b0 && PIX_CLK_DELAY == 1'b1) // if(PIX_CLK == 1'b0 && PIX_CLK_DELAY == 1'b1)
begin // begin
VSYNC_DELAY <= {VSYNC_DELAY[138:0], VSYNC_FLAG}; // VSYNC_DELAY <= {VSYNC_DELAY[138:0], VSYNC_FLAG};
end // end
assign VSYNC_N = VSYNC_FLAG;
/***************************************************************************** /*****************************************************************************
* Keeps track of how many lines are in each row. * Keeps track of how many lines are in each row.
-112
View File
@@ -1,112 +0,0 @@
////////////////////////////////////////////////////////////////////////////////
// Project Name: CoCo3FPGA Version 5.x.x
// File Name: Music_Speech.sv
//
// CoCo3 in an FPGA
//
////////////////////////////////////////////////////////////////////////////////
//
////////////////////////////////////////////////////////////////////////////////
//
// Color Computer 3 compatible system on a chip
//
//
// Copyright (c) 2008 Gary Becker ([email protected])
//
// All rights reserved
//
// Redistribution and use in source and synthezised forms, with or without
// modification, are permitted provided that the following conditions are met:
//
// Redistributions of source code must retain the above copyright notice,
// this list of conditions and the following disclaimer.
//
// Redistributions in synthesized form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the distribution.
//
// Neither the name of the author nor the names of other contributors may
// be used to endorse or promote products derived from this software without
// specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
// THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
// PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
// CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
// POSSIBILITY OF SUCH DAMAGE.
//
// Please report bugs to the author, but before you do so, please
// make sure that this is not a derivative work and that
// you have the latest version of this file.
//
//
////////////////////////////////////////////////////////////////////////////////
// Stan Hodge
//
// Music_Speech.sv by Stan Hodge 02/16/24
////////////////////////////////////////////////////////////////////////////////
module Music_Speech_SOC(
input RESET_N,
input CLKIN,
input CLK_1_78,
input INT1_N,
input INT3_N,
output [7:0] PORT_A,
output [7:0] PORT_B,
output [7:0] PORT_C,
output [7:0] PORT_D_OUT,
input [7:0] PORT_D_IN
);
//////////////////////////////////////////////////////////////////////////////////
// 09 Processor
wire VMA, RW_N, HALT, CPU_IRQ_N, CPU_FIRQ_N, NMI_09;
wire [15:0] ADDRESS;
wire [7:0] DATA_IN, DATA_OUT;
// CPU section copyrighted by John Kent
cpu09 GLBCPU09(
.clk(CLKIN),
.rst(!RESET_N),
.vma(VMA),
.addr(ADDRESS),
.rw(RW_N),
.data_in(DATA_IN),
.data_out(DATA_OUT),
.halt(HALT),
.hold(hold | ~cpu_ena), // ???
.irq(!CPU_IRQ_N),
.firq(!CPU_FIRQ_N),
.nmi(NMI_09)
);
assign DATA_IN = (ADDRESS[15:7] == 8'b00000000) ? ram_data_out:
/////////////////////////////////////////////////////////////////////////////
// SRAM Chip
wire [7:0] ram_data_out;
wire sram_write_enable;
COCO_SRAM_128x8 CoCo3_SRAM_128x8(
.CLK(CLK),
.ENA(sram_write_enable),
.ADDR(ADDRESS[6:0]),
.R_N(RW_N),
.DATA_O(ram_data_out),
.DATA_I(DATA_OUT)
);
endmodule
+195
View File
@@ -0,0 +1,195 @@
--------------------------------------------------------------------------------
-- Overlay
--------------------------------------------------------------------------------
-- DO 10/2017
-- SH 5/15/26 Modified for COCO3
--------------------------------------------------------------------------------
LIBRARY ieee;
USE ieee.std_logic_1164.ALL;
USE ieee.numeric_std.ALL;
ENTITY ovo IS
GENERIC (
COLS : natural :=32;
LINES : natural :=2;
RGB : unsigned(23 DOWNTO 0) :=x"FFFFFF";
H_OFFSET : natural :=4;
V_OFFSET : natural :=45
);
PORT (
-- VGA IN
i_r : IN unsigned(7 DOWNTO 0);
i_g : IN unsigned(7 DOWNTO 0);
i_b : IN unsigned(7 DOWNTO 0);
-- i_hs : IN std_logic;
-- i_vs : IN std_logic;
-- i_de : IN std_logic;
-- i_en : IN std_logic;
i_clk : IN std_logic;
i_Hcount : IN unsigned(10 DOWNTO 0);
i_VCount : IN unsigned(9 DOWNTO 0);
-- VGA_OUT
o_r : OUT unsigned(7 DOWNTO 0);
o_g : OUT unsigned(7 DOWNTO 0);
o_b : OUT unsigned(7 DOWNTO 0);
-- o_hs : OUT std_logic;
-- o_vs : OUT std_logic;
-- o_de : OUT std_logic;
-- Control
ena : IN std_logic; -- Overlay ON/OFF
-- Probes
in0 : IN unsigned(COLS*5-1 downto 0);
in1 : IN unsigned(COLS*5-1 downto 0)
);
END ENTITY ovo;
--##############################################################################
ARCHITECTURE rtl OF ovo IS
TYPE arr_slv8 IS ARRAY (natural RANGE <>) OF unsigned(7 DOWNTO 0);
CONSTANT chars : arr_slv8 :=(
x"3E", x"63", x"73", x"7B", x"6F", x"67", x"3E", x"00", -- 0
x"0C", x"0E", x"0C", x"0C", x"0C", x"0C", x"3F", x"00", -- 1
x"1E", x"33", x"30", x"1C", x"06", x"33", x"3F", x"00", -- 2
x"1E", x"33", x"30", x"1C", x"30", x"33", x"1E", x"00", -- 3
x"38", x"3C", x"36", x"33", x"7F", x"30", x"78", x"00", -- 4
x"3F", x"03", x"1F", x"30", x"30", x"33", x"1E", x"00", -- 5
x"1C", x"06", x"03", x"1F", x"33", x"33", x"1E", x"00", -- 6
x"3F", x"33", x"30", x"18", x"0C", x"0C", x"0C", x"00", -- 7
x"1E", x"33", x"33", x"1E", x"33", x"33", x"1E", x"00", -- 8
x"1E", x"33", x"33", x"3E", x"30", x"18", x"0E", x"00", -- 9
x"0C", x"1E", x"33", x"33", x"3F", x"33", x"33", x"00", -- A
x"3F", x"66", x"66", x"3E", x"66", x"66", x"3F", x"00", -- B
x"3C", x"66", x"03", x"03", x"03", x"66", x"3C", x"00", -- C
x"1F", x"36", x"66", x"66", x"66", x"36", x"1F", x"00", -- D
x"7F", x"46", x"16", x"1E", x"16", x"46", x"7F", x"00", -- E
x"7F", x"46", x"16", x"1E", x"16", x"06", x"0F", x"00", -- F
x"00", x"00", x"00", x"00", x"00", x"00", x"00", x"00", --' ' 10
x"00", x"00", x"3F", x"00", x"00", x"3F", x"00", x"00", -- = 11
x"00", x"0C", x"0C", x"3F", x"0C", x"0C", x"00", x"00", -- + 12
x"00", x"00", x"00", x"3F", x"00", x"00", x"00", x"00", -- - 13
x"18", x"0C", x"06", x"03", x"06", x"0C", x"18", x"00", -- < 14
x"06", x"0C", x"18", x"30", x"18", x"0C", x"06", x"00", -- > 15
x"08", x"1C", x"36", x"63", x"41", x"00", x"00", x"00", -- ^ 16
x"08", x"1C", x"36", x"63", x"41", x"00", x"00", x"00", -- v 17
x"18", x"0C", x"06", x"06", x"06", x"0C", x"18", x"00", -- ( 18
x"06", x"0C", x"18", x"18", x"18", x"0C", x"06", x"00", -- ) 19
x"00", x"0C", x"0C", x"00", x"00", x"0C", x"0C", x"00", -- : 1A
-- x"00", x"00", x"00", x"00", x"00", x"0C", x"0C", x"00", -- . 1B
-- x"00", x"00", x"00", x"00", x"00", x"0C", x"0C", x"06", -- , 1C
-- x"1E", x"33", x"30", x"18", x"0C", x"00", x"0C", x"00", -- ? 1D
-- x"18", x"18", x"18", x"00", x"18", x"18", x"18", x"00", -- | 1E
x"41", x"43", x"45", x"49", x"51", x"61", x"41", x"00", -- N 1B
x"3E", x"41", x"41", x"41", x"41", x"41", x"3E", x"00", -- O 1C
x"3F", x"41", x"41", x"3F", x"11", x"21", x"41", x"00", -- R 1D
x"41", x"63", x"55", x"49", x"41", x"41", x"41", x"00", -- M 1E
x"36", x"36", x"7F", x"36", x"7F", x"36", x"36", x"00"); -- # 1F
SIGNAL vcpt,hcpt,hcpt2 : natural RANGE 0 TO 4095;
SIGNAL vin0,vin1 : unsigned(0 TO COLS*5-1);
SIGNAL t_r,t_g,t_b : unsigned(7 DOWNTO 0);
SIGNAL t_hs,t_vs,t_de : std_logic;
SIGNAL col : unsigned(7 DOWNTO 0);
SIGNAL de : std_logic;
SIGNAL in0s,in1s : unsigned(in0'range);
BEGIN
in0s<=in0 WHEN rising_edge(i_clk);
in1s<=in1 WHEN rising_edge(i_clk);
----------------------------------------------------------
Megamix:PROCESS(i_clk) IS
VARIABLE vin_v : unsigned(0 TO 32*5-1);
VARIABLE char_v : unsigned(4 DOWNTO 0);
BEGIN
IF rising_edge(i_clk) THEN
--IF i_en='1' THEN
----------------------------------
-- Propagate VGA signals. 2 cycles delay
t_r<=i_r;
t_g<=i_g;
t_b<=i_b;
-- t_hs<=i_hs;
-- t_vs<=i_vs;
-- t_de<=i_de;
o_r<=t_r;
o_g<=t_g;
o_b<=t_b;
-- o_hs<=t_hs;
-- o_vs<=t_vs;
-- o_de<=t_de;
----------------------------------
-- Latch sampled values during vertical sync
-- IF i_vs='1' THEN
IF (i_Hcount="000000000" and i_VCount="000000000") THEN
vin0<=in0s;
vin1<=in1s;
END IF;
----------------------------------
-- IF i_vs='1' THEN
-- vcpt<=0;
-- de<='0';
-- ELSIF i_hs='1' AND t_hs='0' AND de='1' THEN
-- vcpt<=(vcpt+1) MOD 4096;
-- END IF;
-- if (i_Hcount < 148) then -- 148 = video left border
-- if (i_Hcount < 148) then -- 148 = video left border
if (i_Hcount < H_OFFSET) then -- 4 = video left border
hcpt <= COLS*8;
else
hcpt <= to_integer(i_Hcount)-H_OFFSET;
end if;
-- if (i_Vcount < 16) then
-- if (i_Vcount < 16) then
if (i_Vcount < V_OFFSET) then
vcpt <= 512;
else
vcpt <= to_integer(i_Vcount)-V_OFFSET;
end if;
----------------------------------
IF (vcpt/8) MOD 2=0 THEN
vin_v:=vin0;
ELSE
vin_v:=vin1;
END IF;
-- IF i_hs='1' THEN
-- hcpt<=0;
-- ELSIF i_de='1' THEN
-- hcpt<=(hcpt+1) MOD 4096;
-- de<='1';
-- END IF;
hcpt2<=hcpt;
----------------------------------
-- Pick characters
IF hcpt<COLS * 8 AND vcpt<LINES * 8 THEN
-- no=> need to reverse string so 0-4 is left (not right!)
char_v:=vin_v((hcpt/8)*5 TO (hcpt/8)*5+4);
-- char_v:=vin_v(((COLS-1) - (hcpt/8))*5 TO ((COLS-1) - (hcpt/8))*5+4);
ELSE
char_v:="10000"; -- " " : Blank character
END IF;
col<=chars(to_integer(char_v)*8+(vcpt MOD 8));
----------------------------------
-- Insert Overlay
IF ena='1' THEN
IF col(hcpt2 MOD 8)='1' THEN
o_r<=RGB(23 DOWNTO 16);
o_g<=RGB(15 DOWNTO 8);
o_b<=RGB( 7 DOWNTO 0);
END IF;
END IF;
--END IF;
END IF;
END PROCESS Megamix;
END ARCHITECTURE rtl;
-66
View File
@@ -1,66 +0,0 @@
//============================================================================
// Audio compressor (signed samples)
//
// Copyright (C) 2018 Sorgelig
//
// This program is free software; you can redistribute it and/or modify it
// under the terms of the GNU General Public License as published by the Free
// Software Foundation; either version 2 of the License, or (at your option)
// any later version.
//
// This program is distributed in the hope that it will be useful, but WITHOUT
// ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
// FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
// more details.
//
// You should have received a copy of the GNU General Public License along
// with this program; if not, write to the Free Software Foundation, Inc.,
// 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
//============================================================================
module compressor
(
input clk,
input [9:0] din,
output [8:0] dout
);
always @(posedge clk) dout <= {din[9], din[9] ? ~tbl[~din[8:0]] : tbl[din[8:0]]};
wire [7:0] tbl[0:511] =
'{
8'h00, 8'h01, 8'h02, 8'h03, 8'h04, 8'h06, 8'h07, 8'h08, 8'h09, 8'h0B, 8'h0C, 8'h0D, 8'h0E, 8'h0F, 8'h11, 8'h12,
8'h13, 8'h14, 8'h16, 8'h17, 8'h18, 8'h19, 8'h1B, 8'h1C, 8'h1D, 8'h1E, 8'h1F, 8'h21, 8'h22, 8'h23, 8'h24, 8'h25,
8'h27, 8'h28, 8'h29, 8'h2A, 8'h2C, 8'h2D, 8'h2E, 8'h2F, 8'h30, 8'h32, 8'h33, 8'h34, 8'h35, 8'h36, 8'h37, 8'h39,
8'h3A, 8'h3B, 8'h3C, 8'h3D, 8'h3F, 8'h40, 8'h41, 8'h42, 8'h43, 8'h44, 8'h46, 8'h47, 8'h48, 8'h49, 8'h4A, 8'h4B,
8'h4D, 8'h4E, 8'h4F, 8'h50, 8'h51, 8'h52, 8'h53, 8'h55, 8'h56, 8'h57, 8'h58, 8'h59, 8'h5A, 8'h5B, 8'h5C, 8'h5E,
8'h5F, 8'h60, 8'h61, 8'h62, 8'h63, 8'h64, 8'h65, 8'h66, 8'h67, 8'h69, 8'h6A, 8'h6B, 8'h6C, 8'h6D, 8'h6E, 8'h6F,
8'h70, 8'h71, 8'h72, 8'h73, 8'h74, 8'h75, 8'h76, 8'h77, 8'h78, 8'h79, 8'h7A, 8'h7B, 8'h7C, 8'h7D, 8'h7E, 8'h7F,
8'h80, 8'h81, 8'h82, 8'h83, 8'h84, 8'h85, 8'h86, 8'h87, 8'h88, 8'h89, 8'h8A, 8'h8B, 8'h8C, 8'h8D, 8'h8E, 8'h8F,
8'h90, 8'h91, 8'h92, 8'h93, 8'h94, 8'h95, 8'h96, 8'h96, 8'h97, 8'h98, 8'h99, 8'h9A, 8'h9B, 8'h9C, 8'h9D, 8'h9E,
8'h9E, 8'h9F, 8'hA0, 8'hA1, 8'hA2, 8'hA3, 8'hA4, 8'hA4, 8'hA5, 8'hA6, 8'hA7, 8'hA8, 8'hA9, 8'hA9, 8'hAA, 8'hAB,
8'hAC, 8'hAD, 8'hAD, 8'hAE, 8'hAF, 8'hB0, 8'hB1, 8'hB1, 8'hB2, 8'hB3, 8'hB4, 8'hB4, 8'hB5, 8'hB6, 8'hB7, 8'hB7,
8'hB8, 8'hB9, 8'hB9, 8'hBA, 8'hBB, 8'hBC, 8'hBC, 8'hBD, 8'hBE, 8'hBE, 8'hBF, 8'hC0, 8'hC0, 8'hC1, 8'hC2, 8'hC2,
8'hC3, 8'hC4, 8'hC4, 8'hC5, 8'hC6, 8'hC6, 8'hC7, 8'hC8, 8'hC8, 8'hC9, 8'hC9, 8'hCA, 8'hCB, 8'hCB, 8'hCC, 8'hCC,
8'hCD, 8'hCE, 8'hCE, 8'hCF, 8'hCF, 8'hD0, 8'hD0, 8'hD1, 8'hD2, 8'hD2, 8'hD3, 8'hD3, 8'hD4, 8'hD4, 8'hD5, 8'hD5,
8'hD6, 8'hD6, 8'hD7, 8'hD7, 8'hD8, 8'hD8, 8'hD9, 8'hD9, 8'hDA, 8'hDA, 8'hDB, 8'hDB, 8'hDC, 8'hDC, 8'hDD, 8'hDD,
8'hDE, 8'hDE, 8'hDE, 8'hDF, 8'hDF, 8'hE0, 8'hE0, 8'hE1, 8'hE1, 8'hE1, 8'hE2, 8'hE2, 8'hE3, 8'hE3, 8'hE3, 8'hE4,
8'hE4, 8'hE5, 8'hE5, 8'hE5, 8'hE6, 8'hE6, 8'hE6, 8'hE7, 8'hE7, 8'hE7, 8'hE8, 8'hE8, 8'hE9, 8'hE9, 8'hE9, 8'hEA,
8'hEA, 8'hEA, 8'hEA, 8'hEB, 8'hEB, 8'hEB, 8'hEC, 8'hEC, 8'hEC, 8'hED, 8'hED, 8'hED, 8'hEE, 8'hEE, 8'hEE, 8'hEE,
8'hEF, 8'hEF, 8'hEF, 8'hEF, 8'hF0, 8'hF0, 8'hF0, 8'hF0, 8'hF1, 8'hF1, 8'hF1, 8'hF1, 8'hF2, 8'hF2, 8'hF2, 8'hF2,
8'hF3, 8'hF3, 8'hF3, 8'hF3, 8'hF3, 8'hF4, 8'hF4, 8'hF4, 8'hF4, 8'hF4, 8'hF5, 8'hF5, 8'hF5, 8'hF5, 8'hF5, 8'hF6,
8'hF6, 8'hF6, 8'hF6, 8'hF6, 8'hF6, 8'hF7, 8'hF7, 8'hF7, 8'hF7, 8'hF7, 8'hF7, 8'hF8, 8'hF8, 8'hF8, 8'hF8, 8'hF8,
8'hF8, 8'hF8, 8'hF9, 8'hF9, 8'hF9, 8'hF9, 8'hF9, 8'hF9, 8'hF9, 8'hF9, 8'hFA, 8'hFA, 8'hFA, 8'hFA, 8'hFA, 8'hFA,
8'hFA, 8'hFA, 8'hFA, 8'hFB, 8'hFB, 8'hFB, 8'hFB, 8'hFB, 8'hFB, 8'hFB, 8'hFB, 8'hFB, 8'hFB, 8'hFB, 8'hFC, 8'hFC,
8'hFC, 8'hFC, 8'hFC, 8'hFC, 8'hFC, 8'hFC, 8'hFC, 8'hFC, 8'hFC, 8'hFC, 8'hFC, 8'hFC, 8'hFC, 8'hFD, 8'hFD, 8'hFD,
8'hFD, 8'hFD, 8'hFD, 8'hFD, 8'hFD, 8'hFD, 8'hFD, 8'hFD, 8'hFD, 8'hFD, 8'hFD, 8'hFD, 8'hFD, 8'hFD, 8'hFD, 8'hFD,
8'hFD, 8'hFD, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE,
8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE,
8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE,
8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE,
8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE,
8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE,
8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFE, 8'hFF
};
endmodule
-444
View File
@@ -1,444 +0,0 @@
---------------------------------------------------------------------------------
-- sp0256 by Dar ([email protected]) (14/04/2018)
-- http://darfpga.blogspot.fr
---------------------------------------------------------------------------------
-- Educational use only
-- Do not redistribute synthetized file with roms
-- Do not redistribute roms whatever the form
-- Use at your own risk
---------------------------------------------------------------------------------
--
-- SP0256-al2 prom decoding scheme and speech synthesis algorithm are from :
--
-- Copyright Joseph Zbiciak, all rights reserved.
-- Copyright tim lindner, all rights reserved.
--
-- See C source code and license in sp0256.c from MAME source
--
-- VHDL code is by Dar.
--
---------------------------------------------------------------------------------
--
-- One allophone is made of N parts (called here after lines), each part has a
-- 16 bytes descriptor. One descriptor (for one part) contains one repeat value
-- one amplitude value, one period value and 2x6 filtering coefficients.
--
-- for line_cnt from 0 to nb_line-1 (part)
-- for line_rpt from 0 to line_rpt-1 (repeat)
-- for per_cnt from 0 to line_per-1 (period)
-- produce 1 sample
--
-- One sample is the output of the 6 stages filter. Each filter stage is fed by
-- the output of the previous stage, the first stage is fed by the source sample
--
-- when line_per != 0 source sample is set to amplitude value only once at the
-- begin of each repeat (per_cnt==0) then source sample is set to 0
--
-- when line_per == 0 source sample is set to amplitude value only at the begin
-- of each repeat (per_cnt==0) then source sample sign is toggled (+/-) when then
-- random noise generator lsb equal 1. In that case actual line_per is set to 64
--
--
-- Sound sample frequency is 10kHz. I make a 25 stages linear state machine
-- running at 250kHz that produce one sound sample per cycle.
--
-- As long as one allophones is available the state machine runs permanently and
-- there is zero latency between allophones.
--
-- During one (each) cycle the state machine:
--
-- - fetch new allophone or go on with current one if not finished
-- - get allophone first line descriptor address from rom entry table
-- - get allophone nb_line from rom entry table and jump to first line address
-- - get allophone line_rpt from rom current line descriptor
-- - get allophone amplitude from rom current line descriptor
-- manage source amplitude, reset filter if needed
-- - get allophone line_per from rom current line descriptor
-- - address filter coefficients F/B within rom current line descriptor,
-- feed filter input, update filter state with computation output
-- - rescale last filter stage output to audio output
-- - manage per_cnt, rpt_cnt, line_cnt and random noise generator
--
-- Filter computation:
--
-- Filter coefficients F or B index is get from rom current line descriptor
-- (address managed by state machine), value is converted thru coeff_array
-- table. Coefficient index has a sign bit to be managed:
--
-- if index sign bit = 0, filter coefficient <= -coeff_array(index)
-- if index sign bit = 1, filter coefficient <= coeff_array(-index)
--
-- During one state machine cycle each filter is updated once.
-- One filter update require two state machine steps:
--
-- step 1
-- sum_in1 <= filter input
-- sum_in2 <= filter coefficient F * filter state z1 / 256
-- sum_out <= sum_in1 + sum_in2
-- step 2
-- sum_in1 <= sum_out
-- sum_in2 <= filter coefficient B * filter state z2 / 512
-- sum_out <= sum_in1 + sum_in2
-- filter state z1 <= sum_in1 + sum_in2
-- filter state z2 <= filter state z1
--
-- (sum_out will be limited to -32768/+32767)
--
-- Audio output scaling to 10bits unsigned:
--
-- what :
-- Last filter output is limited to -8192/+8191
-- Then divided by 16 => -512/+511
-- Then offset by 512 => 0/1023
--
-- how:
-- if X > 8191, Y <= 1023
-- elsif X < -8192, Y <= 0
-- else Y <= (X/16)+512
--
---------------------------------------------------------------------------------
library ieee;
use ieee.std_logic_1164.ALL;
use ieee.std_logic_unsigned.all;
use ieee.numeric_std.all;
entity sp0256 is
port
(
clock : in std_logic;
ce : in std_logic;
reset : in std_logic;
input_rdy : out std_logic;
allophone : in std_logic_vector(5 downto 0);
trig_allophone : in std_logic;
audio_out : out signed(9 downto 0)
);
end sp0256;
architecture syn of sp0256 is
signal rom_addr : std_logic_vector(11 downto 0);
signal rom_do : std_logic_vector( 7 downto 0);
signal stage : integer range 0 to 24; -- stage counter 0-24;
signal allo_entry : std_logic_vector(7 downto 0);
signal allo_addr_lsb, allo_addr_msb : std_logic_vector(7 downto 0);
signal allo_nb_line : std_logic_vector(7 downto 0);
signal line_rpt, line_per : std_logic_vector(7 downto 0);
signal line_amp_lsb, line_amp_msb : std_logic_vector(7 downto 0);
signal amp, filter, coeff : signed(15 downto 0);
signal sum_in2 : signed(31 downto 0);
signal sum_in1,sum_out_ul : signed(15 downto 0);
signal sum_out : signed(15 downto 0);
signal divider : std_logic;
signal audio : signed(9 downto 0);
signal audio_int : signed(8 downto 0);
signal is_noise : std_logic;
signal noise_rng : std_logic_vector(15 downto 0) := X"0001";
signal f0_z1,f0_z2 : signed(15 downto 0);
signal f1_z1,f1_z2 : signed(15 downto 0);
signal f2_z1,f2_z2 : signed(15 downto 0);
signal f3_z1,f3_z2 : signed(15 downto 0);
signal f4_z1,f4_z2 : signed(15 downto 0);
signal f5_z1,f5_z2 : signed(15 downto 0);
signal input_rdy_in : std_logic;
signal sound_on : std_logic := '0';
signal trig_allophone_r : std_logic;
signal line_cnt, rpt_cnt, per_cnt : std_logic_vector(7 downto 0);
signal coeff_idx : std_logic_vector(6 downto 0);
type coeff_array_t is array(0 to 127) of integer range 0 to 511;
constant coeff_array : coeff_array_t := (
0, 9, 17, 25, 33, 41, 49, 57,
65, 73, 81, 89, 97, 105, 113, 121,
129, 137, 145, 153, 161, 169, 177, 185,
193, 201, 209, 217, 225, 233, 241, 249,
257, 265, 273, 281, 289, 297, 301, 305,
309, 313, 317, 321, 325, 329, 333, 337,
341, 345, 349, 353, 357, 361, 365, 369,
373, 377, 381, 385, 389, 393, 397, 401,
405, 409, 413, 417, 421, 425, 427, 429,
431, 433, 435, 437, 439, 441, 443, 445,
447, 449, 451, 453, 455, 457, 459, 461,
463, 465, 467, 469, 471, 473, 475, 477,
479, 481, 482, 483, 484, 485, 486, 487,
488, 489, 490, 491, 492, 493, 494, 495,
496, 497, 498, 499, 500, 501, 502, 503,
504, 505, 506, 507, 508, 509, 510, 511);
component compressor is port
(
clk : in std_logic;
din : in signed(9 downto 0);
dout : out signed(8 downto 0)
);
end component;
begin
input_rdy <= input_rdy_in;
-- stage counter : Fs=250k/25 = 10kHz
process (clock, reset)
begin
if reset='1' then
stage <= 0;
else
if rising_edge(clock) then
if ce = '1' then
if stage >= 24 then
stage <= 0;
else
stage <= stage + 1;
end if;
end if;
end if;
end if;
end process;
process (clock, reset)
begin
if reset='1' then
input_rdy_in <= '1';
sound_on <= '0';
noise_rng <= X"0001";
else
if rising_edge(clock) then if ce = '1' then
trig_allophone_r <= trig_allophone;
if trig_allophone = '1' and trig_allophone_r = '0' then
input_rdy_in <= '0';
end if;
if sound_on = '0' then
if stage = 0 and input_rdy_in = '0' then
allo_entry <= allophone*"11";
rom_addr <= X"0"&(allophone*"11");
line_cnt <= (others => '0');
rpt_cnt <= (others => '0');
per_cnt <= (others => '0');
sound_on <= '1';
input_rdy_in <= '1';
end if;
else -- sound is on
case stage is
when 0 =>
rom_addr <= X"0"&allo_entry;
when 1 =>
--allo_addr_msb <= rom_do;
rom_addr <= rom_addr + '1';
when 2 =>
allo_addr_lsb <= rom_do;
rom_addr <= rom_addr + '1';
when 3 =>
allo_nb_line <= rom_do - '1';
rom_addr <= (allo_addr_lsb +line_cnt) & X"0";
when 4 =>
line_rpt <= rom_do - '1';
rom_addr <= rom_addr + '1';
when 5 =>
line_amp_msb <= rom_do;
rom_addr <= rom_addr + '1';
when 6 =>
if per_cnt = X"00" then
amp <= signed(line_amp_msb & rom_do);
else
if is_noise = '1' then
if noise_rng(0) = '1' then
amp <= -amp;
end if;
else
amp <= (others => '0');
end if;
end if;
if per_cnt = X"00"then
f0_z1 <= (others => '0'); f0_z2 <= (others => '0');
f1_z1 <= (others => '0'); f1_z2 <= (others => '0');
f2_z1 <= (others => '0'); f2_z2 <= (others => '0');
f3_z1 <= (others => '0'); f3_z2 <= (others => '0');
f4_z1 <= (others => '0'); f4_z2 <= (others => '0');
f5_z1 <= (others => '0'); f5_z2 <= (others => '0');
end if;
rom_addr <= rom_addr + '1';
when 7 =>
if rom_do = X"00" then
line_per <= X"40";
is_noise <= '1';
else
line_per <= rom_do - '1';
is_noise <= '0';
end if;
sum_in1 <= amp;
filter <= f0_z1;
divider <= '0';
rom_addr <= rom_addr + '1';
when 8 =>
sum_in1 <= sum_out;
filter <= f0_z2;
divider <= '1';
rom_addr <= rom_addr + '1';
when 9 =>
f0_z1 <= sum_out;
f0_z2 <= f0_z1;
sum_in1 <= sum_out;
filter <= f1_z1;
divider <= '0';
rom_addr <= rom_addr + '1';
when 10 =>
sum_in1 <= sum_out;
filter <= f1_z2;
divider <= '1';
rom_addr <= rom_addr + '1';
when 11 =>
f1_z1 <= sum_out;
f1_z2 <= f1_z1;
sum_in1 <= sum_out;
filter <= f2_z1;
divider <= '0';
rom_addr <= rom_addr + '1';
when 12 =>
sum_in1 <= sum_out;
filter <= f2_z2;
divider <= '1';
rom_addr <= rom_addr + '1';
when 13 =>
f2_z1 <= sum_out;
f2_z2 <= f2_z1;
sum_in1 <= sum_out;
filter <= f3_z1;
divider <= '0';
rom_addr <= rom_addr + '1';
when 14 =>
sum_in1 <= sum_out;
filter <= f3_z2;
divider <= '1';
rom_addr <= rom_addr + '1';
when 15 =>
f3_z1 <= sum_out;
f3_z2 <= f3_z1;
sum_in1 <= sum_out;
filter <= f4_z1;
divider <= '0';
rom_addr <= rom_addr + '1';
when 16 =>
sum_in1 <= sum_out;
filter <= f4_z2;
divider <= '1';
rom_addr <= rom_addr + '1';
when 17 =>
f4_z1 <= sum_out;
f4_z2 <= f4_z1;
sum_in1 <= sum_out;
filter <= f5_z1;
divider <= '0';
rom_addr <= rom_addr + '1';
when 18 =>
sum_in1 <= sum_out;
filter <= f5_z2;
divider <= '1';
rom_addr <= rom_addr + '1';
when 19 =>
f5_z1 <= sum_out;
f5_z2 <= f5_z1;
if sum_out > 510*16 then
audio <= to_signed(511,10);
elsif sum_out < -511*16 then
audio <= to_signed(-512,10);
else
audio <= sum_out(13 downto 4);
end if;
when 20 =>
if per_cnt >= line_per then
per_cnt <= (others => '0');
if rpt_cnt >= line_rpt then
rpt_cnt <= (others => '0');
if line_cnt >= allo_nb_line then
line_cnt <= (others => '0');
sound_on <= '0';
else
line_cnt <= line_cnt + '1';
end if;
is_noise <= '0';
else
rpt_cnt <= rpt_cnt + '1';
end if;
else
per_cnt <= per_cnt + '1';
end if;
if noise_rng(0) = '1' then
noise_rng <= ('0' & noise_rng(15 downto 1) ) xor X"4001";
else
noise_rng <= '0' & noise_rng(15 downto 1);
end if;
when others => null;
end case;
end if;
end if; end if;
end if;
end process;
compr: compressor
port map
(
clk => clock,
din => audio,
dout => audio_int
);
audio_out <= audio_int(8) & audio_int;
-- filter computation
coeff_idx <= rom_do(6 downto 0) when rom_do(7)='0' else
not(rom_do(6 downto 0)) + '1';
coeff <= -to_signed(coeff_array(to_integer(unsigned(coeff_idx))),16) when rom_do(7)='0' else
to_signed(coeff_array(to_integer(unsigned(coeff_idx))),16);
sum_in2 <= (filter * coeff) / 256 when divider = '0' else
(filter * coeff) / 512 ;
sum_out_ul <= sum_in1 + sum_in2(15 downto 0);
sum_out <= to_signed( 32767,16) when sum_out_ul > 32767 else
to_signed(-32768,16) when sum_out_ul < -32768 else
sum_out_ul;
-- sp0256-al2 prom (decoded)
sp0256_al2_decoded : entity work.sp0256_al2_decoded
port map(
clk => clock,
addr => rom_addr,
data => rom_do
);
end syn;
-373
View File
@@ -1,373 +0,0 @@
---------------------------------------------------------------------------------
-- sp0256 by Dar ([email protected]) (14/04/2018)
-- http://darfpga.blogspot.fr
---------------------------------------------------------------------------------
-- Educational use only
-- Do not redistribute synthetized file with roms
-- Do not redistribute roms whatever the form
-- Use at your own risk
---------------------------------------------------------------------------------
--
-- SP0256-al2 prom decoding scheme and speech synthesis algorithm are from :
--
-- Copyright Joseph Zbiciak, all rights reserved.
-- Copyright tim lindner, all rights reserved.
--
-- See C source code and license in sp0256.c from MAME source
--
-- VHDL code is by Dar.
--
---------------------------------------------------------------------------------
-- Original sp0256 prom is bit compressed. I used sp0256.c from MAME to produce
-- an uncompressed and more easy format to be used in FPGA.
--
-- Original prom is 2K, uncompressed prom is 4k.
--
-- Uncompressed format is :
--
-- 64 entries table of 3 bytes/entry : adr_msb, adr_lsb, nb_line (nb parts)
-- (1 entry per allophone)
--
-- Each allophone is made of #nb_line parts
--
-- Each part is described by 16 bytes (one line) :
--
-- rpt : repeat nb
-- amp_msb, amp_lsb : amplitude
-- per : periode (number of sample to be produced for each rpt)
-- F0|B0|F1|B1|F2|B2|F3|B3|F4|B4|F5|B5 : filtering coefficients
--
---------------------------------------------------------------------------------
library ieee;
use ieee.std_logic_1164.all,ieee.numeric_std.all;
entity sp0256_al2_decoded is
port (
clk : in std_logic;
addr : in std_logic_vector(11 downto 0);
data : out std_logic_vector(7 downto 0)
);
end entity;
architecture prom of sp0256_al2_decoded is
type rom is array(0 to 4095) of std_logic_vector(7 downto 0);
signal rom_data: rom := (
-- adr_msb|adr_lsb|nb_line
X"00",X"0C",X"01", -- #00 : 000-002
X"00",X"0D",X"01", -- #01 : 003-005
X"00",X"0E",X"01", -- #02 : 006-008
X"00",X"0F",X"01", -- #03 : 009-00B
X"00",X"10",X"01", -- #04 : 00C-00E
X"00",X"11",X"0A", -- #05 : 00F-011
X"00",X"1B",X"0A", -- #06 : 012-014
X"00",X"25",X"01", -- #07 : 015-017
X"00",X"26",X"03", -- #08 : 018-01A
X"00",X"29",X"03", -- #09 : 01B-01D
X"00",X"2C",X"03", -- #0A : 01E-020
X"00",X"2F",X"03", -- #0B : 021-023
X"00",X"32",X"01", -- #0C : 024-026
X"00",X"33",X"04", -- #0D : 027-029
X"00",X"37",X"06", -- #0E : 02A-02C
X"00",X"3D",X"01", -- #0F : 02D-02F
X"00",X"3E",X"04", -- #10 : 030-032
X"00",X"42",X"03", -- #11 : 033-035
X"00",X"45",X"02", -- #12 : 036-038
X"00",X"47",X"06", -- #13 : 039-03B
X"00",X"4D",X"08", -- #14 : 03C-03E
X"00",X"55",X"02", -- #15 : 03F-041
X"00",X"57",X"03", -- #16 : 042-044
X"00",X"5A",X"01", -- #17 : 045-047
X"00",X"5B",X"03", -- #18 : 048-04A
X"00",X"5E",X"06", -- #19 : 04B-04D
X"00",X"64",X"01", -- #1A : 04E-050
X"00",X"65",X"03", -- #1B : 051-053
X"00",X"68",X"02", -- #1C : 054-056
X"00",X"6A",X"01", -- #1D : 057-059
X"00",X"6B",X"01", -- #1E : 05A-05C
X"00",X"6C",X"03", -- #1F : 05D-05F
X"00",X"6F",X"05", -- #20 : 060-062
X"00",X"74",X"03", -- #21 : 063-065
X"00",X"77",X"03", -- #22 : 066-068
X"00",X"7A",X"03", -- #23 : 069-06B
X"00",X"7D",X"03", -- #24 : 06C-06E
X"00",X"80",X"04", -- #25 : 06F-071
X"00",X"84",X"02", -- #26 : 072-074
X"00",X"86",X"03", -- #27 : 075-077
X"00",X"89",X"01", -- #28 : 078-07A
X"00",X"8A",X"03", -- #29 : 07B-07D
X"00",X"8D",X"04", -- #2A : 07E-080
X"00",X"91",X"03", -- #2B : 081-083
X"00",X"94",X"04", -- #2C : 084-086
X"00",X"98",X"03", -- #2D : 087-089
X"00",X"9B",X"03", -- #2E : 08A-08C
X"00",X"9E",X"0D", -- #2F : 08D-08F
X"00",X"AB",X"04", -- #30 : 090-092
X"00",X"AF",X"04", -- #31 : 093-095
X"00",X"B3",X"03", -- #32 : 096-098
X"00",X"B6",X"09", -- #33 : 099-09B
X"00",X"BF",X"0A", -- #34 : 09C-09E
X"00",X"C9",X"06", -- #35 : 09F-0A1
X"00",X"CF",X"02", -- #36 : 0A2-0A4
X"00",X"D1",X"01", -- #37 : 0A5-0A7
X"00",X"D2",X"06", -- #38 : 0A8-0AA
X"00",X"D8",X"02", -- #39 : 0AB-0AD
X"00",X"DA",X"09", -- #3A : 0AE-0B0
X"00",X"E3",X"09", -- #3B : 0B1-0B3
X"00",X"EC",X"08", -- #3C : 0B4-0B6
X"00",X"F4",X"03", -- #3D : 0B7-0B9
X"00",X"F7",X"03", -- #3E : 0BA-0BC
X"00",X"FA",X"03", -- #3F : 0BD-0BF
-- rpt|amp_msb mp_lsb|per|F0|B0|F1|B1|F2|B2|F3|B3|F4|B4|F5|B5
X"01",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #00.0 : 0C0-0CF
X"04",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #01.0 : 0D0-0DF
X"07",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #02.0 : 0E0-0EF
X"0F",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #03.0 : 0F0-0FF
X"1F",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #04.0 : 100-10F
X"03",X"01",X"40",X"5B",X"A0",X"60",X"B8",X"60",X"F8",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #05.0 : 110-11F
X"03",X"00",X"C0",X"5B",X"A0",X"60",X"B0",X"60",X"F8",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #05.1 : 120-12F
X"01",X"00",X"50",X"5B",X"A0",X"60",X"A8",X"60",X"F8",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #05.2 : 130-13F
X"03",X"00",X"80",X"5B",X"A0",X"60",X"B0",X"60",X"F8",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #05.3 : 140-14F
X"01",X"00",X"70",X"5B",X"A0",X"60",X"B0",X"60",X"F8",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #05.4 : 150-15F
X"04",X"00",X"A0",X"5B",X"A0",X"60",X"B8",X"60",X"F8",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #05.5 : 160-16F
X"02",X"01",X"C0",X"5B",X"A8",X"60",X"C0",X"60",X"F8",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #05.6 : 170-17F
X"04",X"02",X"80",X"5B",X"A8",X"60",X"D0",X"60",X"F8",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #05.7 : 180-18F
X"02",X"02",X"80",X"5B",X"A8",X"60",X"E0",X"60",X"F8",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #05.8 : 190-19F
X"09",X"01",X"00",X"5B",X"A0",X"60",X"E8",X"60",X"F8",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #05.9 : 1A0-1AF
X"01",X"03",X"00",X"5B",X"B0",X"70",X"C8",X"70",X"F8",X"60",X"18",X"50",X"3C",X"44",X"00",X"00", -- #06.0 : 1B0-1BF
X"01",X"02",X"80",X"5B",X"C8",X"70",X"B0",X"70",X"F8",X"60",X"18",X"50",X"3C",X"44",X"00",X"00", -- #06.1 : 1C0-1CF
X"02",X"03",X"00",X"5B",X"C8",X"70",X"B0",X"70",X"F8",X"60",X"18",X"50",X"3C",X"44",X"00",X"00", -- #06.2 : 1D0-1DF
X"02",X"02",X"80",X"5B",X"B0",X"70",X"C8",X"70",X"F8",X"60",X"18",X"50",X"3C",X"44",X"00",X"00", -- #06.3 : 1E0-1EF
X"02",X"02",X"00",X"5B",X"C8",X"70",X"F8",X"70",X"B8",X"60",X"18",X"50",X"3C",X"44",X"00",X"00", -- #06.4 : 1F0-1FF
X"02",X"02",X"80",X"5B",X"B0",X"70",X"D0",X"70",X"F8",X"60",X"18",X"50",X"3C",X"44",X"00",X"00", -- #06.5 : 200-20F
X"03",X"03",X"80",X"5B",X"B0",X"70",X"F8",X"70",X"E0",X"60",X"18",X"50",X"3C",X"44",X"00",X"00", -- #06.6 : 210-21F
X"01",X"03",X"00",X"5B",X"A8",X"70",X"E0",X"70",X"F8",X"60",X"18",X"50",X"3C",X"44",X"00",X"00", -- #06.7 : 220-22F
X"03",X"02",X"80",X"5B",X"A0",X"70",X"E8",X"70",X"00",X"60",X"18",X"50",X"3C",X"44",X"00",X"00", -- #06.8 : 230-23F
X"02",X"01",X"00",X"5B",X"A0",X"70",X"F0",X"70",X"00",X"60",X"18",X"50",X"3C",X"44",X"00",X"00", -- #06.9 : 240-24F
X"06",X"06",X"00",X"5B",X"00",X"50",X"28",X"50",X"40",X"50",X"F8",X"10",X"E8",X"58",X"AA",X"64", -- #07.0 : 250-25F
X"04",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #08.0 : 260-26F
X"03",X"00",X"28",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"38",X"40",X"FC",X"04",X"CB",X"68", -- #08.1 : 270-27F
X"05",X"00",X"20",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"20",X"18",X"20",X"40",X"C5",X"62", -- #08.2 : 280-28F
X"0D",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #09.0 : 290-29F
X"04",X"00",X"14",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"28",X"40",X"F4",X"2C",X"BF",X"3B", -- #09.1 : 2A0-2AF
X"06",X"00",X"20",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"28",X"50",X"F8",X"44",X"CF",X"3A", -- #09.2 : 2B0-2BF
X"04",X"00",X"50",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"28",X"20",X"18",X"42",X"FA",X"30", -- #0A.0 : 2C0-2CF
X"04",X"01",X"C0",X"5B",X"18",X"60",X"30",X"50",X"38",X"20",X"00",X"10",X"00",X"60",X"E6",X"38", -- #0A.1 : 2D0-2DF
X"04",X"01",X"40",X"5B",X"18",X"50",X"28",X"40",X"40",X"30",X"FC",X"68",X"E8",X"52",X"DD",X"16", -- #0A.2 : 2E0-2EF
X"07",X"00",X"38",X"5B",X"00",X"30",X"18",X"20",X"38",X"40",X"FC",X"60",X"E0",X"2A",X"A1",X"54", -- #0B.0 : 2F0-2FF
X"03",X"00",X"50",X"5B",X"08",X"30",X"20",X"30",X"20",X"10",X"FC",X"68",X"E8",X"1C",X"A2",X"50", -- #0B.1 : 300-30F
X"09",X"00",X"60",X"5B",X"08",X"30",X"20",X"40",X"20",X"10",X"FC",X"68",X"E0",X"24",X"9B",X"5B", -- #0B.2 : 310-31F
X"05",X"06",X"00",X"5B",X"00",X"50",X"10",X"20",X"30",X"50",X"E8",X"60",X"34",X"1E",X"A0",X"6E", -- #0C.0 : 320-32F
X"05",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #0D.0 : 330-33F
X"03",X"00",X"A0",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"34",X"28",X"1C",X"4E",X"F4",X"21", -- #0D.1 : 340-34F
X"04",X"00",X"50",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"30",X"20",X"1C",X"44",X"EA",X"53", -- #0D.2 : 350-35F
X"03",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"24",X"18",X"1C",X"46",X"E7",X"5A", -- #0D.3 : 360-36F
X"05",X"00",X"1C",X"5B",X"98",X"60",X"C0",X"60",X"E0",X"50",X"0C",X"40",X"20",X"3C",X"32",X"2B", -- #0E.0 : 370-37F
X"03",X"00",X"50",X"5B",X"98",X"60",X"C0",X"60",X"E8",X"50",X"0C",X"40",X"20",X"3C",X"32",X"2B", -- #0E.1 : 380-38F
X"01",X"00",X"C0",X"5B",X"98",X"60",X"C0",X"60",X"E8",X"50",X"0C",X"40",X"20",X"3C",X"32",X"2B", -- #0E.2 : 390-39F
X"02",X"02",X"80",X"5B",X"A0",X"60",X"C0",X"60",X"F0",X"50",X"0C",X"40",X"20",X"3C",X"32",X"2B", -- #0E.3 : 3A0-3AF
X"01",X"01",X"C0",X"5B",X"A0",X"60",X"B8",X"60",X"F0",X"50",X"0C",X"40",X"20",X"3C",X"32",X"2B", -- #0E.4 : 3B0-3BF
X"02",X"02",X"00",X"5B",X"A0",X"60",X"B8",X"60",X"F0",X"50",X"0C",X"40",X"20",X"3C",X"32",X"2B", -- #0E.5 : 3C0-3CF
X"06",X"06",X"00",X"5B",X"F0",X"50",X"18",X"20",X"28",X"60",X"D0",X"60",X"28",X"18",X"A8",X"61", -- #0F.0 : 3D0-3DF
X"06",X"00",X"A0",X"5B",X"F0",X"50",X"C0",X"30",X"E0",X"20",X"00",X"10",X"20",X"44",X"00",X"00", -- #10.0 : 3E0-3EF
X"05",X"00",X"C0",X"5B",X"F0",X"50",X"C0",X"30",X"E0",X"20",X"00",X"10",X"20",X"44",X"00",X"00", -- #10.1 : 3F0-3FF
X"05",X"00",X"E0",X"5B",X"F0",X"50",X"E0",X"30",X"C8",X"20",X"00",X"10",X"20",X"44",X"00",X"00", -- #10.2 : 400-40F
X"04",X"01",X"40",X"5B",X"F0",X"50",X"E0",X"30",X"C8",X"20",X"00",X"10",X"20",X"44",X"00",X"00", -- #10.3 : 410-41F
X"06",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #11.0 : 420-42F
X"01",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"40",X"48",X"10",X"40",X"DF",X"3F", -- #11.1 : 430-43F
X"05",X"00",X"28",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"24",X"18",X"28",X"40",X"E8",X"3F", -- #11.2 : 440-44F
X"0C",X"00",X"A0",X"5B",X"08",X"30",X"18",X"30",X"38",X"40",X"EC",X"30",X"D4",X"2E",X"CB",X"20", -- #12.0 : 450-45F
X"03",X"02",X"80",X"5B",X"00",X"60",X"18",X"50",X"38",X"50",X"F4",X"08",X"DC",X"5E",X"A1",X"5C", -- #12.1 : 460-46F
X"03",X"06",X"00",X"5B",X"08",X"00",X"28",X"40",X"38",X"40",X"04",X"60",X"F0",X"66",X"A1",X"5A", -- #13.0 : 470-47F
X"03",X"06",X"00",X"5B",X"28",X"40",X"38",X"40",X"08",X"00",X"04",X"50",X"F4",X"62",X"A4",X"57", -- #13.1 : 480-48F
X"02",X"06",X"00",X"5B",X"08",X"10",X"28",X"50",X"38",X"40",X"04",X"48",X"F4",X"64",X"9A",X"62", -- #13.2 : 490-49F
X"03",X"06",X"00",X"5B",X"08",X"20",X"28",X"50",X"38",X"40",X"04",X"38",X"F8",X"60",X"96",X"66", -- #13.3 : 4A0-4AF
X"04",X"04",X"00",X"5B",X"08",X"30",X"28",X"50",X"38",X"50",X"FC",X"20",X"F8",X"62",X"92",X"6E", -- #13.4 : 4B0-4BF
X"04",X"01",X"40",X"5B",X"08",X"40",X"28",X"40",X"38",X"40",X"F8",X"60",X"F4",X"0C",X"90",X"71", -- #13.5 : 4C0-4CF
X"03",X"03",X"00",X"5B",X"A0",X"70",X"E8",X"60",X"00",X"20",X"04",X"30",X"28",X"52",X"00",X"00", -- #14.0 : 4D0-4DF
X"01",X"03",X"00",X"5B",X"A0",X"70",X"F0",X"60",X"00",X"20",X"04",X"30",X"28",X"52",X"00",X"00", -- #14.1 : 4E0-4EF
X"03",X"02",X"80",X"5B",X"A0",X"70",X"F0",X"60",X"00",X"20",X"04",X"30",X"28",X"52",X"00",X"00", -- #14.2 : 4F0-4FF
X"01",X"01",X"C0",X"5B",X"98",X"70",X"F8",X"60",X"F8",X"20",X"04",X"30",X"28",X"52",X"00",X"00", -- #14.3 : 500-50F
X"05",X"01",X"C0",X"5B",X"98",X"70",X"F8",X"60",X"00",X"20",X"04",X"30",X"28",X"52",X"00",X"00", -- #14.4 : 510-51F
X"01",X"01",X"C0",X"5B",X"98",X"70",X"F8",X"60",X"00",X"20",X"04",X"30",X"28",X"52",X"00",X"00", -- #14.5 : 520-52F
X"06",X"00",X"A0",X"5B",X"90",X"70",X"F8",X"60",X"00",X"20",X"04",X"30",X"28",X"52",X"00",X"00", -- #14.6 : 530-53F
X"02",X"00",X"70",X"5B",X"90",X"70",X"F8",X"60",X"F8",X"20",X"04",X"30",X"28",X"52",X"00",X"00", -- #14.7 : 540-54F
X"03",X"02",X"80",X"5B",X"90",X"70",X"E0",X"70",X"00",X"60",X"10",X"10",X"1C",X"56",X"3A",X"49", -- #15.0 : 550-55F
X"02",X"02",X"00",X"5B",X"98",X"70",X"E0",X"70",X"00",X"60",X"10",X"10",X"1C",X"56",X"3A",X"49", -- #15.1 : 560-56F
X"03",X"05",X"00",X"5B",X"98",X"60",X"F0",X"60",X"D8",X"60",X"1C",X"58",X"24",X"4E",X"39",X"2C", -- #16.0 : 570-57F
X"02",X"05",X"00",X"5B",X"D0",X"60",X"F0",X"60",X"A0",X"60",X"1C",X"58",X"24",X"4E",X"39",X"2C", -- #16.1 : 580-58F
X"02",X"04",X"00",X"5B",X"F0",X"60",X"C8",X"60",X"A0",X"60",X"1C",X"58",X"24",X"4E",X"39",X"2C", -- #16.2 : 590-59F
X"08",X"04",X"00",X"5B",X"20",X"50",X"18",X"20",X"40",X"30",X"F8",X"60",X"C0",X"60",X"B2",X"5A", -- #17.0 : 5A0-5AF
X"03",X"05",X"00",X"5B",X"C8",X"60",X"B8",X"60",X"F8",X"60",X"14",X"28",X"1C",X"36",X"44",X"41", -- #18.0 : 5B0-5BF
X"02",X"05",X"00",X"5B",X"C8",X"60",X"B8",X"60",X"F8",X"60",X"14",X"28",X"1C",X"36",X"44",X"41", -- #18.1 : 5C0-5CF
X"02",X"05",X"00",X"5B",X"B8",X"60",X"C8",X"60",X"F8",X"60",X"14",X"28",X"1C",X"36",X"44",X"41", -- #18.2 : 5D0-5DF
X"03",X"01",X"C0",X"5B",X"10",X"50",X"28",X"40",X"30",X"30",X"08",X"30",X"F0",X"64",X"8E",X"70", -- #19.0 : 5E0-5EF
X"02",X"01",X"80",X"5B",X"10",X"50",X"28",X"50",X"38",X"30",X"04",X"28",X"F4",X"5E",X"8C",X"76", -- #19.1 : 5F0-5FF
X"04",X"02",X"80",X"5B",X"08",X"30",X"28",X"40",X"30",X"20",X"08",X"40",X"F4",X"5C",X"90",X"70", -- #19.2 : 600-60F
X"01",X"04",X"00",X"5B",X"10",X"30",X"20",X"50",X"38",X"40",X"00",X"38",X"F0",X"5A",X"95",X"69", -- #19.3 : 610-61F
X"03",X"07",X"00",X"5B",X"20",X"40",X"28",X"40",X"18",X"10",X"00",X"48",X"F0",X"60",X"98",X"69", -- #19.4 : 620-62F
X"01",X"06",X"00",X"5B",X"18",X"30",X"28",X"40",X"20",X"10",X"00",X"48",X"F0",X"5E",X"9C",X"68", -- #19.5 : 630-63F
X"09",X"03",X"00",X"5B",X"F8",X"40",X"20",X"50",X"30",X"50",X"F0",X"20",X"DC",X"4C",X"AE",X"66", -- #1A.0 : 640-64F
X"06",X"00",X"1C",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"24",X"28",X"08",X"4E",X"EB",X"0C", -- #1B.0 : 650-65F
X"06",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"34",X"38",X"0C",X"3E",X"F1",X"1A", -- #1B.1 : 660-66F
X"02",X"00",X"14",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"20",X"30",X"E8",X"F2",X"03",X"3F", -- #1B.2 : 670-67F
X"03",X"00",X"04",X"5B",X"F8",X"30",X"18",X"40",X"40",X"30",X"E4",X"20",X"18",X"04",X"88",X"76", -- #1C.0 : 680-68F
X"01",X"03",X"00",X"5B",X"20",X"50",X"18",X"10",X"30",X"40",X"F8",X"78",X"E0",X"74",X"98",X"6C", -- #1C.1 : 690-69F
X"14",X"00",X"28",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"30",X"30",X"10",X"24",X"E5",X"3B", -- #1D.0 : 6A0-6AF
X"08",X"02",X"80",X"5B",X"F8",X"70",X"20",X"50",X"28",X"50",X"C0",X"68",X"18",X"06",X"A4",X"5E", -- #1E.0 : 6B0-6BF
X"08",X"02",X"80",X"5B",X"F0",X"60",X"18",X"60",X"20",X"40",X"D8",X"60",X"20",X"0C",X"9D",X"61", -- #1F.0 : 6C0-6CF
X"04",X"03",X"00",X"5B",X"18",X"50",X"20",X"50",X"38",X"30",X"F0",X"60",X"D0",X"66",X"A6",X"53", -- #1F.1 : 6D0-6DF
X"07",X"02",X"00",X"5B",X"18",X"60",X"28",X"50",X"40",X"40",X"F0",X"60",X"C8",X"62",X"9D",X"61", -- #1F.2 : 6E0-6EF
X"08",X"01",X"C0",X"5B",X"B8",X"60",X"D0",X"60",X"F8",X"50",X"0C",X"20",X"20",X"44",X"00",X"00", -- #20.0 : 6F0-6FF
X"05",X"01",X"00",X"5B",X"B0",X"60",X"C8",X"60",X"F8",X"50",X"0C",X"20",X"20",X"44",X"00",X"00", -- #20.1 : 700-70F
X"04",X"00",X"A0",X"5B",X"B0",X"60",X"C0",X"60",X"F8",X"50",X"0C",X"20",X"20",X"44",X"00",X"00", -- #20.2 : 710-71F
X"04",X"00",X"80",X"5B",X"A8",X"60",X"C0",X"60",X"00",X"50",X"0C",X"20",X"20",X"44",X"00",X"00", -- #20.3 : 720-72F
X"07",X"00",X"28",X"5B",X"A0",X"60",X"B8",X"60",X"00",X"50",X"0C",X"20",X"20",X"44",X"00",X"00", -- #20.4 : 730-73F
X"04",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #21.0 : 740-74F
X"03",X"00",X"38",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"28",X"20",X"14",X"32",X"E7",X"23", -- #21.1 : 750-75F
X"03",X"06",X"00",X"5B",X"18",X"50",X"20",X"50",X"40",X"30",X"F8",X"60",X"E4",X"72",X"9D",X"5D", -- #21.2 : 760-76F
X"08",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #22.0 : 770-77F
X"05",X"00",X"38",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"30",X"48",X"F4",X"42",X"EA",X"2A", -- #22.1 : 780-78F
X"03",X"01",X"40",X"5B",X"20",X"30",X"30",X"50",X"18",X"10",X"F8",X"68",X"E8",X"58",X"9C",X"68", -- #22.2 : 790-79F
X"06",X"00",X"20",X"5B",X"08",X"30",X"28",X"50",X"50",X"40",X"F0",X"48",X"C8",X"68",X"A8",X"47", -- #23.0 : 7A0-7AF
X"06",X"00",X"E0",X"5B",X"10",X"40",X"28",X"40",X"50",X"50",X"F0",X"40",X"D0",X"1A",X"DE",X"3A", -- #23.1 : 7B0-7BF
X"02",X"01",X"40",X"5B",X"F0",X"60",X"18",X"40",X"20",X"40",X"D0",X"68",X"2C",X"18",X"C7",X"25", -- #23.2 : 7C0-7CF
X"04",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #24.0 : 7D0-7DF
X"03",X"00",X"20",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"14",X"30",X"FC",X"F0",X"FB",X"41", -- #24.1 : 7E0-7EF
X"03",X"03",X"80",X"5B",X"10",X"40",X"20",X"60",X"38",X"30",X"F8",X"30",X"F4",X"5E",X"A1",X"5C", -- #24.2 : 7F0-7FF
X"06",X"00",X"10",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"1C",X"50",X"0C",X"0E",X"FB",X"5C", -- #25.0 : 800-80F
X"03",X"00",X"60",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"24",X"18",X"18",X"42",X"FA",X"56", -- #25.1 : 810-81F
X"12",X"00",X"60",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"20",X"18",X"18",X"4A",X"FC",X"5B", -- #25.2 : 820-82F
X"04",X"00",X"50",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"24",X"18",X"10",X"2E",X"F8",X"4C", -- #25.3 : 830-83F
X"07",X"01",X"40",X"5B",X"C0",X"30",X"E0",X"40",X"F8",X"60",X"14",X"58",X"24",X"48",X"00",X"00", -- #26.0 : 840-84F
X"0B",X"00",X"80",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"20",X"42",X"FE",X"3F", -- #26.1 : 850-85F
X"02",X"00",X"38",X"5B",X"08",X"40",X"20",X"30",X"38",X"30",X"DC",X"48",X"BC",X"58",X"A4",X"54", -- #27.0 : 860-86F
X"03",X"00",X"60",X"5B",X"D0",X"60",X"10",X"70",X"20",X"30",X"BC",X"60",X"1C",X"08",X"A1",X"5D", -- #27.1 : 870-87F
X"04",X"00",X"A0",X"5B",X"D0",X"50",X"10",X"60",X"18",X"50",X"BC",X"60",X"20",X"0E",X"A3",X"5C", -- #27.2 : 880-88F
X"11",X"00",X"38",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"28",X"38",X"04",X"28",X"E3",X"27", -- #28.0 : 890-89F
X"12",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #29.0 : 8A0-8AF
X"01",X"00",X"38",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"34",X"30",X"04",X"12",X"DE",X"56", -- #29.1 : 8B0-8BF
X"02",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"2C",X"28",X"F4",X"1E",X"DC",X"49", -- #29.2 : 8C0-8CF
X"07",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #2A.0 : 8D0-8DF
X"01",X"00",X"A0",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"30",X"38",X"0C",X"62",X"E2",X"37", -- #2A.1 : 8E0-8EF
X"01",X"00",X"1C",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"2C",X"20",X"10",X"36",X"F9",X"44", -- #2A.2 : 8F0-8FF
X"09",X"00",X"50",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"2C",X"28",X"0C",X"44",X"E7",X"1B", -- #2A.3 : 900-90F
X"06",X"04",X"00",X"5B",X"20",X"50",X"40",X"60",X"58",X"50",X"00",X"58",X"DC",X"54",X"A7",X"4D", -- #2B.0 : 910-91F
X"09",X"00",X"60",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"44",X"58",X"EC",X"00",X"21",X"30", -- #2B.1 : 920-92F
X"04",X"05",X"00",X"5B",X"20",X"50",X"40",X"50",X"48",X"40",X"00",X"40",X"DC",X"60",X"B9",X"37", -- #2B.2 : 930-93F
X"05",X"03",X"80",X"5B",X"D8",X"40",X"B8",X"40",X"F8",X"40",X"04",X"58",X"2C",X"3C",X"55",X"5A", -- #2C.0 : 940-94F
X"03",X"02",X"00",X"5B",X"F0",X"40",X"B0",X"40",X"D8",X"40",X"04",X"58",X"2C",X"3C",X"55",X"5A", -- #2C.1 : 950-95F
X"06",X"01",X"C0",X"5B",X"B0",X"40",X"F0",X"40",X"D8",X"40",X"04",X"58",X"2C",X"3C",X"55",X"5A", -- #2C.2 : 960-96F
X"08",X"01",X"40",X"5B",X"F0",X"40",X"B0",X"40",X"D0",X"40",X"04",X"58",X"2C",X"3C",X"55",X"5A", -- #2C.3 : 970-97F
X"03",X"00",X"C0",X"5B",X"98",X"60",X"C8",X"60",X"08",X"40",X"18",X"30",X"28",X"44",X"2E",X"25", -- #2D.0 : 980-98F
X"03",X"02",X"80",X"5B",X"A0",X"60",X"C8",X"60",X"08",X"40",X"18",X"30",X"28",X"44",X"2E",X"25", -- #2D.1 : 990-99F
X"03",X"02",X"00",X"5B",X"A0",X"60",X"C0",X"60",X"00",X"40",X"18",X"30",X"28",X"44",X"2E",X"25", -- #2D.2 : 9A0-9AF
X"05",X"00",X"28",X"5B",X"F8",X"20",X"18",X"40",X"28",X"30",X"C0",X"38",X"10",X"F8",X"A0",X"5A", -- #2E.0 : 9B0-9BF
X"05",X"00",X"38",X"5B",X"08",X"30",X"20",X"60",X"38",X"40",X"FC",X"08",X"B0",X"50",X"9E",X"5F", -- #2E.1 : 9C0-9CF
X"06",X"00",X"50",X"5B",X"00",X"50",X"18",X"60",X"20",X"50",X"A8",X"70",X"14",X"02",X"93",X"72", -- #2E.2 : 9D0-9DF
X"03",X"02",X"80",X"5B",X"A0",X"60",X"E8",X"60",X"F8",X"60",X"00",X"10",X"1C",X"52",X"42",X"59", -- #2F.0 : 9E0-9EF
X"02",X"02",X"80",X"5B",X"A0",X"60",X"E8",X"60",X"F8",X"60",X"00",X"10",X"1C",X"52",X"42",X"59", -- #2F.1 : 9F0-9FF
X"02",X"01",X"C0",X"5B",X"A0",X"60",X"E8",X"60",X"F0",X"60",X"00",X"10",X"1C",X"52",X"42",X"59", -- #2F.2 : A00-A0F
X"02",X"02",X"80",X"5B",X"A0",X"60",X"E0",X"60",X"F0",X"60",X"00",X"10",X"1C",X"52",X"42",X"59", -- #2F.3 : A10-A1F
X"02",X"03",X"00",X"5B",X"A8",X"60",X"E0",X"60",X"F0",X"60",X"00",X"10",X"1C",X"52",X"42",X"59", -- #2F.4 : A20-A2F
X"02",X"02",X"80",X"5B",X"A8",X"60",X"D8",X"60",X"E8",X"60",X"00",X"10",X"1C",X"52",X"42",X"59", -- #2F.5 : A30-A3F
X"03",X"02",X"00",X"5B",X"A8",X"60",X"D8",X"60",X"E8",X"60",X"00",X"10",X"1C",X"52",X"42",X"59", -- #2F.6 : A40-A4F
X"01",X"01",X"C0",X"5B",X"A8",X"60",X"D8",X"60",X"E8",X"60",X"00",X"10",X"1C",X"52",X"42",X"59", -- #2F.7 : A50-A5F
X"03",X"00",X"E0",X"5B",X"A8",X"60",X"D0",X"60",X"E0",X"60",X"00",X"10",X"1C",X"52",X"42",X"59", -- #2F.8 : A60-A6F
X"01",X"00",X"80",X"5B",X"A0",X"60",X"D0",X"60",X"E0",X"60",X"00",X"10",X"1C",X"52",X"42",X"59", -- #2F.9 : A70-A7F
X"02",X"00",X"C0",X"5B",X"A8",X"60",X"D0",X"60",X"E8",X"60",X"00",X"10",X"1C",X"52",X"42",X"59", -- #2F.A : A80-A8F
X"01",X"00",X"70",X"5B",X"A8",X"60",X"D0",X"60",X"E8",X"60",X"00",X"10",X"1C",X"52",X"42",X"59", -- #2F.B : A90-A9F
X"03",X"00",X"50",X"5B",X"A8",X"60",X"D8",X"60",X"E8",X"60",X"00",X"10",X"1C",X"52",X"42",X"59", -- #2F.C : AA0-AAF
X"06",X"00",X"0C",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"20",X"20",X"FC",X"1C",X"D2",X"28", -- #30.0 : AB0-ABF
X"0B",X"00",X"0C",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"24",X"38",X"04",X"18",X"B4",X"55", -- #30.1 : AC0-ACF
X"02",X"00",X"C0",X"5B",X"F8",X"40",X"30",X"70",X"20",X"20",X"C4",X"38",X"10",X"FC",X"A3",X"5D", -- #30.2 : AD0-ADF
X"02",X"01",X"40",X"5B",X"F8",X"60",X"28",X"50",X"28",X"50",X"B0",X"68",X"1C",X"06",X"A3",X"58", -- #30.3 : AE0-AEF
X"03",X"01",X"C0",X"5B",X"10",X"50",X"28",X"40",X"30",X"30",X"08",X"30",X"F0",X"64",X"8E",X"70", -- #31.0 : AF0-AFF
X"02",X"01",X"80",X"5B",X"10",X"50",X"28",X"50",X"38",X"30",X"04",X"28",X"F4",X"5E",X"8C",X"76", -- #31.1 : B00-B0F
X"04",X"02",X"80",X"5B",X"08",X"30",X"28",X"40",X"30",X"20",X"08",X"40",X"F4",X"5C",X"90",X"70", -- #31.2 : B10-B1F
X"01",X"04",X"00",X"5B",X"10",X"30",X"20",X"50",X"38",X"40",X"00",X"38",X"F0",X"5A",X"95",X"69", -- #31.3 : B20-B2F
X"05",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #32.0 : B30-B3F
X"05",X"00",X"14",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"28",X"40",X"08",X"4E",X"E4",X"19", -- #32.1 : B40-B4F
X"0D",X"00",X"50",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"34",X"50",X"10",X"66",X"F6",X"49", -- #32.2 : B50-B5F
X"01",X"02",X"80",X"5B",X"18",X"40",X"20",X"40",X"30",X"20",X"E4",X"60",X"CC",X"68",X"A5",X"5F", -- #33.0 : B60-B6F
X"02",X"02",X"80",X"5B",X"18",X"40",X"20",X"40",X"28",X"10",X"E4",X"58",X"D0",X"60",X"A5",X"5F", -- #33.1 : B70-B7F
X"01",X"02",X"80",X"5B",X"E0",X"60",X"18",X"40",X"20",X"40",X"D0",X"60",X"24",X"12",X"A8",X"5B", -- #33.2 : B80-B8F
X"01",X"02",X"00",X"5B",X"E0",X"60",X"18",X"50",X"28",X"40",X"D0",X"60",X"20",X"0A",X"A3",X"63", -- #33.3 : B90-B9F
X"01",X"01",X"C0",X"5B",X"E0",X"60",X"18",X"60",X"28",X"40",X"D0",X"68",X"20",X"0A",X"A5",X"61", -- #33.4 : BA0-BAF
X"02",X"02",X"00",X"5B",X"E0",X"60",X"18",X"50",X"28",X"40",X"D0",X"60",X"24",X"12",X"A2",X"69", -- #33.5 : BB0-BBF
X"01",X"01",X"40",X"5B",X"E0",X"60",X"18",X"60",X"28",X"40",X"D4",X"68",X"1C",X"0A",X"A0",X"6E", -- #33.6 : BC0-BCF
X"02",X"00",X"E0",X"5B",X"18",X"60",X"20",X"20",X"20",X"10",X"E0",X"60",X"D4",X"68",X"A0",X"6E", -- #33.7 : BD0-BDF
X"01",X"01",X"00",X"5B",X"18",X"60",X"18",X"20",X"30",X"20",X"E4",X"60",X"D4",X"6A",X"A3",X"63", -- #33.8 : BE0-BEF
X"02",X"02",X"80",X"5B",X"18",X"40",X"20",X"40",X"30",X"20",X"E4",X"60",X"CC",X"68",X"A5",X"5F", -- #34.0 : BF0-BFF
X"02",X"02",X"80",X"5B",X"18",X"40",X"20",X"40",X"28",X"10",X"E4",X"58",X"D0",X"60",X"A5",X"5F", -- #34.1 : C00-C0F
X"02",X"02",X"00",X"5B",X"E0",X"60",X"18",X"40",X"28",X"40",X"D0",X"60",X"24",X"10",X"A9",X"59", -- #34.2 : C10-C1F
X"02",X"02",X"00",X"5B",X"E0",X"60",X"18",X"40",X"20",X"40",X"D0",X"60",X"24",X"12",X"A8",X"5B", -- #34.3 : C20-C2F
X"02",X"01",X"C0",X"5B",X"E0",X"60",X"18",X"50",X"28",X"40",X"D0",X"60",X"20",X"0A",X"A3",X"63", -- #34.4 : C30-C3F
X"02",X"01",X"C0",X"5B",X"E0",X"60",X"18",X"60",X"28",X"40",X"D0",X"68",X"20",X"0A",X"A5",X"61", -- #34.5 : C40-C4F
X"02",X"01",X"C0",X"5B",X"E0",X"60",X"18",X"50",X"28",X"40",X"D0",X"60",X"24",X"12",X"A2",X"69", -- #34.6 : C50-C5F
X"03",X"01",X"40",X"5B",X"E0",X"60",X"18",X"60",X"28",X"40",X"D4",X"68",X"1C",X"0A",X"A0",X"6E", -- #34.7 : C60-C6F
X"03",X"00",X"C0",X"5B",X"18",X"60",X"20",X"20",X"20",X"10",X"E0",X"60",X"D4",X"68",X"A0",X"6E", -- #34.8 : C70-C7F
X"03",X"00",X"E0",X"5B",X"18",X"60",X"18",X"20",X"30",X"20",X"E4",X"60",X"D4",X"6A",X"A3",X"63", -- #34.9 : C80-C8F
X"03",X"02",X"80",X"5B",X"A8",X"60",X"C0",X"60",X"F8",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #35.0 : C90-C9F
X"03",X"02",X"00",X"5B",X"A8",X"60",X"C0",X"60",X"00",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #35.1 : CA0-CAF
X"01",X"01",X"C0",X"5B",X"A8",X"60",X"C0",X"60",X"00",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #35.2 : CB0-CBF
X"05",X"00",X"C0",X"5B",X"A0",X"60",X"B8",X"60",X"00",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #35.3 : CC0-CCF
X"01",X"00",X"C0",X"5B",X"A0",X"60",X"B8",X"60",X"00",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #35.4 : CD0-CDF
X"06",X"00",X"70",X"5B",X"A0",X"60",X"B8",X"60",X"00",X"60",X"40",X"60",X"24",X"60",X"00",X"00", -- #35.5 : CE0-CEF
X"11",X"00",X"A0",X"5B",X"08",X"30",X"18",X"30",X"38",X"40",X"EC",X"30",X"D4",X"2E",X"CB",X"20", -- #36.0 : CF0-CFF
X"03",X"02",X"80",X"5B",X"00",X"60",X"18",X"50",X"38",X"50",X"F4",X"08",X"DC",X"5E",X"A1",X"5C", -- #36.1 : D00-D0F
X"0A",X"00",X"70",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"48",X"40",X"20",X"38",X"E3",X"29", -- #37.0 : D10-D1F
X"04",X"00",X"A0",X"5B",X"00",X"30",X"18",X"20",X"38",X"40",X"FC",X"60",X"E0",X"2A",X"A1",X"54", -- #38.0 : D20-D2F
X"02",X"00",X"C0",X"5B",X"08",X"30",X"20",X"30",X"20",X"10",X"FC",X"68",X"E8",X"1C",X"A2",X"50", -- #38.1 : D30-D3F
X"02",X"00",X"C0",X"5B",X"08",X"30",X"20",X"40",X"20",X"10",X"FC",X"68",X"E0",X"24",X"9B",X"5B", -- #38.2 : D40-D4F
X"03",X"06",X"00",X"5B",X"10",X"40",X"18",X"40",X"30",X"30",X"F8",X"68",X"DC",X"62",X"A8",X"50", -- #38.3 : D50-D5F
X"01",X"06",X"00",X"5B",X"10",X"20",X"18",X"40",X"30",X"40",X"F8",X"68",X"D4",X"6E",X"AC",X"55", -- #38.4 : D60-D6F
X"03",X"06",X"00",X"5B",X"20",X"50",X"18",X"10",X"30",X"40",X"F8",X"70",X"D0",X"6A",X"AC",X"58", -- #38.5 : D70-D7F
X"0E",X"00",X"0C",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"20",X"30",X"00",X"1E",X"C1",X"48", -- #39.0 : D80-D8F
X"04",X"00",X"C0",X"5B",X"00",X"40",X"20",X"60",X"38",X"50",X"E8",X"18",X"E0",X"0A",X"C2",X"49", -- #39.1 : D90-D9F
X"02",X"00",X"60",X"5B",X"A0",X"60",X"A8",X"60",X"F8",X"60",X"10",X"20",X"20",X"60",X"37",X"57", -- #3A.0 : DA0-DAF
X"01",X"00",X"40",X"5B",X"A0",X"60",X"A8",X"60",X"F0",X"60",X"10",X"20",X"20",X"60",X"37",X"57", -- #3A.1 : DB0-DBF
X"03",X"00",X"50",X"5B",X"A0",X"60",X"A8",X"60",X"F0",X"60",X"10",X"20",X"20",X"60",X"37",X"57", -- #3A.2 : DC0-DCF
X"03",X"00",X"E0",X"5B",X"A0",X"60",X"B0",X"60",X"F0",X"60",X"10",X"20",X"20",X"60",X"37",X"57", -- #3A.3 : DD0-DDF
X"05",X"01",X"40",X"5B",X"A0",X"60",X"C0",X"60",X"E8",X"60",X"10",X"20",X"20",X"60",X"37",X"57", -- #3A.4 : DE0-DEF
X"04",X"01",X"C0",X"5B",X"A8",X"60",X"C8",X"60",X"E0",X"60",X"10",X"20",X"20",X"60",X"37",X"57", -- #3A.5 : DF0-DFF
X"04",X"01",X"C0",X"5B",X"A8",X"60",X"D0",X"60",X"E0",X"60",X"10",X"20",X"20",X"60",X"37",X"57", -- #3A.6 : E00-E0F
X"01",X"00",X"E0",X"5B",X"A0",X"60",X"D0",X"60",X"E0",X"60",X"10",X"20",X"20",X"60",X"37",X"57", -- #3A.7 : E10-E1F
X"03",X"00",X"60",X"5B",X"A0",X"60",X"D0",X"60",X"E0",X"60",X"10",X"20",X"20",X"60",X"37",X"57", -- #3A.8 : E20-E2F
X"02",X"01",X"00",X"5B",X"18",X"60",X"28",X"40",X"10",X"00",X"F0",X"48",X"BC",X"64",X"AC",X"59", -- #3B.0 : E30-E3F
X"02",X"01",X"40",X"5B",X"10",X"60",X"20",X"40",X"18",X"10",X"F0",X"48",X"BC",X"62",X"AF",X"56", -- #3B.1 : E40-E4F
X"02",X"01",X"80",X"5B",X"10",X"50",X"20",X"30",X"20",X"10",X"EC",X"48",X"C0",X"5E",X"B0",X"56", -- #3B.2 : E50-E5F
X"02",X"01",X"40",X"5B",X"F0",X"50",X"10",X"60",X"20",X"50",X"C0",X"60",X"10",X"02",X"B6",X"51", -- #3B.3 : E60-E6F
X"02",X"01",X"40",X"5B",X"E8",X"60",X"18",X"60",X"28",X"50",X"C4",X"60",X"04",X"00",X"B8",X"4A", -- #3B.4 : E70-E7F
X"03",X"01",X"40",X"5B",X"18",X"60",X"10",X"00",X"20",X"30",X"E8",X"58",X"C8",X"62",X"B5",X"54", -- #3B.5 : E80-E8F
X"03",X"00",X"E0",X"5B",X"00",X"00",X"18",X"60",X"30",X"50",X"E4",X"60",X"CC",X"58",X"B5",X"56", -- #3B.6 : E90-E9F
X"03",X"00",X"C0",X"5B",X"00",X"00",X"18",X"60",X"28",X"40",X"E4",X"60",X"D0",X"5C",X"B2",X"59", -- #3B.7 : EA0-EAF
X"03",X"00",X"80",X"5B",X"E8",X"60",X"10",X"60",X"20",X"20",X"CC",X"60",X"04",X"FC",X"B2",X"55", -- #3B.8 : EB0-EBF
X"03",X"03",X"80",X"5B",X"90",X"70",X"F0",X"50",X"00",X"30",X"04",X"18",X"28",X"4E",X"39",X"41", -- #3C.0 : EC0-ECF
X"02",X"04",X"00",X"5B",X"90",X"70",X"F8",X"50",X"00",X"30",X"04",X"18",X"28",X"4E",X"39",X"41", -- #3C.1 : ED0-EDF
X"03",X"05",X"00",X"5B",X"90",X"70",X"F8",X"50",X"00",X"30",X"04",X"18",X"28",X"4E",X"39",X"41", -- #3C.2 : EE0-EEF
X"02",X"02",X"80",X"5B",X"90",X"70",X"F0",X"50",X"00",X"30",X"04",X"18",X"28",X"4E",X"39",X"41", -- #3C.3 : EF0-EFF
X"03",X"02",X"80",X"5B",X"98",X"70",X"E8",X"50",X"F8",X"30",X"04",X"18",X"28",X"4E",X"39",X"41", -- #3C.4 : F00-F0F
X"04",X"01",X"80",X"5B",X"A0",X"70",X"E0",X"50",X"F0",X"30",X"04",X"18",X"28",X"4E",X"39",X"41", -- #3C.5 : F10-F1F
X"05",X"01",X"80",X"5B",X"A0",X"70",X"D8",X"50",X"F0",X"30",X"04",X"18",X"28",X"4E",X"39",X"41", -- #3C.6 : F20-F2F
X"05",X"01",X"40",X"5B",X"A0",X"70",X"D8",X"50",X"F0",X"30",X"04",X"18",X"28",X"4E",X"39",X"41", -- #3C.7 : F30-F3F
X"04",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #3D.0 : F40-F4F
X"04",X"00",X"1C",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"20",X"38",X"E0",X"40",X"E6",X"1C", -- #3D.1 : F50-F5F
X"02",X"01",X"80",X"5B",X"F8",X"40",X"18",X"60",X"38",X"50",X"F8",X"18",X"D8",X"5C",X"A1",X"70", -- #3D.2 : F60-F6F
X"05",X"03",X"00",X"5B",X"18",X"40",X"28",X"50",X"20",X"20",X"FC",X"68",X"C4",X"60",X"A3",X"64", -- #3E.0 : F70-F7F
X"03",X"01",X"80",X"5B",X"10",X"10",X"28",X"60",X"38",X"40",X"FC",X"60",X"C0",X"62",X"A3",X"60", -- #3E.1 : F80-F8F
X"07",X"01",X"00",X"5B",X"28",X"60",X"18",X"10",X"30",X"30",X"00",X"60",X"C0",X"60",X"A0",X"68", -- #3E.2 : F90-F9F
X"04",X"00",X"00",X"40",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- #3F.0 : FA0-FAF
X"01",X"00",X"18",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"20",X"30",X"FC",X"24",X"DE",X"43", -- #3F.1 : FB0-FBF
X"02",X"05",X"00",X"5B",X"20",X"50",X"30",X"40",X"18",X"10",X"F8",X"68",X"E0",X"6E",X"99",X"6C", -- #3F.2 : FC0-FCF
X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- : FD0-FDF
X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00", -- : FE0-FEF
X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00",X"00" -- : FF0-FFF
);
begin
process(clk)
begin
if rising_edge(clk) then
data <= rom_data(to_integer(unsigned(addr)));
end if;
end process;
end architecture;
+6 -2
View File
@@ -308,8 +308,12 @@ end
assign TX_CLK = (CTL_REG[3:0] == 4'h0) ? XTAL_CLK_IN: assign TX_CLK = (CTL_REG[3:0] == 4'h0) ? XTAL_CLK_IN:
TX_CLK_REG; TX_CLK_REG;
assign RX_CLK = (CTL_REG[4] == 1'b0) ? RX_CLK_IN: // Receiver clock. CTL bit 4 = 0 selects the external RxC input, which used to
TX_CLK; // be the fixed 1.8475 MHz enable (115,200 baud): a program writing CTL=$0F
// (19,200, bit 4 clear -- the FujiNet HDB-DOS L3 cart) then transmitted at
// 19,200 but received at 115,200. RxC is taken from the baud generator
// instead; for CTL[3:0]=0 that is the same 1.8475 MHz clock as before.
assign RX_CLK = TX_CLK;
assign RESET_X = RESET_NX ? 1'b0: assign RESET_X = RESET_NX ? 1'b0:
RESET_N; RESET_N;
File diff suppressed because it is too large. Load diff
+11 -11
View File
@@ -6,16 +6,16 @@ module cassette(
input rewind, input rewind,
input en, input en,
output reg [24:0] sdram_addr, output reg [15:0] sdram_addr,
input [7:0] sdram_data, input [7:0] sdram_data,
output reg sdram_rd, // output reg sdram_rd,
output data, output data
output [2:0] status // output [2:0] status
); );
assign status = state; //assign status = state;
reg old_en; reg old_en;
reg ffrewind; reg ffrewind;
@@ -60,25 +60,25 @@ always @(posedge clk) begin
end end
NEXT: begin NEXT: begin
state <= READ1; state <= READ1;
sdram_rd <= 1'b0; // sdram_rd <= 1'b0;
if (seq == 24'h553c00) name <= 1'd1; if (seq == 24'h553c00) name <= 1'd1;
if (seq == 24'h555555 && name) begin if (seq == 24'h555555 && name) begin
name <= 1'd0; name <= 1'd0;
state <= WAIT; state <= WAIT;
hold <= 19'd445000; // 0.5s hold <= 19'd445000; // 0.5s
sdram_addr <= sdram_addr - 25'd3; sdram_addr <= sdram_addr - 16'd3;
end end
if (seq == 24'h553cff) eof <= 2'd1; if (seq == 24'h553cff) eof <= 2'd1;
if (seq == 24'h00ff55 && eof == 2'd1) eof <= 2'd2; if (seq == 24'h00ff55 && eof == 2'd1) eof <= 2'd2;
if (~en) state <= IDLE; if (~en) state <= IDLE;
end end
READ1: begin READ1: begin
sdram_rd <= 1'b1; // sdram_rd <= 1'b1;
state <= READ2; state <= READ2;
end end
READ2: begin READ2: begin
ibyte <= sdram_data; ibyte <= sdram_data;
sdram_rd <= 1'b0; // sdram_rd <= 1'b0;
state <= READ3; state <= READ3;
sq_start <= 1'b1; sq_start <= 1'b1;
end end
@@ -88,14 +88,14 @@ always @(posedge clk) begin
end end
READ4: begin READ4: begin
seq <= { seq[15:0], sdram_data }; seq <= { seq[15:0], sdram_data };
sdram_addr <= sdram_addr + 25'd1; sdram_addr <= sdram_addr + 16'd1;
state <= eof == 2'd2 ? IDLE : NEXT; state <= eof == 2'd2 ? IDLE : NEXT;
end end
endcase endcase
if (ffrewind ^ rewind) begin if (ffrewind ^ rewind) begin
seq <= 24'd0; seq <= 24'd0;
sdram_addr <= 25'd0; sdram_addr <= 16'd0;
state <= IDLE; state <= IDLE;
eof <= 2'd0; eof <= 2'd0;
end end
+763 -346
View File
File diff suppressed because it is too large. Load diff
+14 -3
View File
@@ -67,12 +67,14 @@ module coco_mem_fetch(
input HBORDER, input HBORDER,
input [6:0] HOR_OFFSET, input [6:0] HOR_OFFSET,
input COCO1, input COCO1,
input [3:0] HRES input [3:0] HRES,
input CT_320_160
); );
localparam WORD_END_COUNT = 9'd160 - 1'd1; wire [8:0] WORD_END_COUNT;
//localparam WORD_END_COUNT = 9'd160 - 1'd1;
wire [24:0] PHY_VID_ADD; wire [24:0] PHY_VID_ADD;
@@ -82,6 +84,11 @@ reg [8:0] read_count;
reg [4:0] state; reg [4:0] state;
reg second_write; reg second_write;
reg init_offset_a0; reg init_offset_a0;
// End-of-line test for the fetch being requested, registered in state_start.
// read_count only changes on SDRAM_VID_ACK, so this equals the old in-line
// compare; it takes the 9-bit compare off the ACK -> VID_READ_OFFSET path,
// which missed timing at 114 MHz.
reg last_fetch;
reg [4:0] a0_delay; reg [4:0] a0_delay;
localparam state_pre_start = 4'd0; localparam state_pre_start = 4'd0;
@@ -90,6 +97,9 @@ localparam state_wait_accept = 4'd2;
localparam state_done = 4'd10; localparam state_done = 4'd10;
assign WORD_END_COUNT = (CT_320_160) ? 9'd320 - 1'd1:
9'd160 - 1'd1;
assign BUF_HBORDER[0] = HBORDER; assign BUF_HBORDER[0] = HBORDER;
assign a0_delay[0] = init_offset_a0; assign a0_delay[0] = init_offset_a0;
@@ -156,6 +166,7 @@ begin
SDRAM_VID_REQ <= 1'b1; SDRAM_VID_REQ <= 1'b1;
state <= state_wait_accept; state <= state_wait_accept;
init_offset_a0 <= PHY_VID_ADD[1]; init_offset_a0 <= PHY_VID_ADD[1];
last_fetch <= (read_count >= WORD_END_COUNT);
end end
end end
@@ -165,7 +176,7 @@ begin
begin begin
SDRAM_VID_REQ <= 1'b0; SDRAM_VID_REQ <= 1'b0;
if (read_count >= WORD_END_COUNT) if (last_fetch)
begin begin
read_count <= 9'h000; read_count <= 9'h000;
state <= state_done; state <= state_done;
+33 -9
View File
@@ -61,23 +61,47 @@
// This file is a configuration definition file. The CoCo3FPGA for MiSTer source files // This file is a configuration definition file. The CoCo3FPGA for MiSTer source files
// can be built into multiple objects which have mutually exclusive features. // can be built into multiple objects which have mutually exclusive features.
`include "../RTL/config_inc.v" `define Config_Debug_FLAG 4'hA
localparam [7:0] FEATURE_1 = 8'h01;
localparam [7:0] FEATURE_2 = 8'h02;
localparam [7:0] FEATURE_3 = 8'h04;
localparam [7:0] FEATURE_4 = 8'h08;
localparam [7:0] FEATURE_5 = 8'h10;
localparam [7:0] FEATURE_6 = 8'h20;
localparam [7:0] FEATURE_7 = 8'h40;
localparam [7:0] FEATURE_8 = 8'h80;
// If defined the Config_Debug sets the FEATURE MASKS all OR'd together which appears on COCO space at FFF1 & (FFF0 = 0x55 as a debug flag) // This is used for hardware debugging - it overrides the USER_IO to be user_out direct.
// It should be commented out for release
//`define Config_Debug //`define Config_Debug
// Feature list - note only FEATURE_1 - FEATURE_8 are supported // Feature list - note only FEATURE_1 - FEATURE_8 are supported
/////////////////////////////////////////////////////////////////////////////////////////////////////////// ///////////////////////////////////////////////////////////////////////////////////////////////////////////
`set_feature(CoCo3_Horz_INT_FIX, FEATURE_1) // Connection of the horz int to the Mister CoCo3 V5 rasterizer // `set_feature(CoCo3_Horz_INT_FIX,Feat_1) // Connection of the horz int to the Mister CoCo3 V5 rasterizer
`define CoCo3_Horz_INT_FIX
`define Feat_1
//`set_feature(CoCo3_Vert_INT_FIX, FEATURE_2) // Connection of the vert int to the Mister CoCo3 V5 rasterizer // `set_feature(CoCo3_Vert_INT_FIX,Feat_2) // Connection of the vert int to the Mister CoCo3 V5 rasterizer
// `define CoCo3_Vert_INT_FIX
// `define Feat_2
`set_feature(CoCo3_CYC_ACC_6809, FEATURE_3) // Use cycle accurate 6809 // `set_feature(CoCo3_CYC_ACC_6809,Feat_3) // Use cycle accurate 6809
`define CoCo3_CYC_ACC_6809
`define Feat_3
`set_feature(CoCo3_sdc_override_size, FEATURE_4) // Define static size value // `set_feature(CoCo3_sdc_override_size,Feat_4) // Define static size value
`define CoCo3_sdc_override_size
`define Feat_4
`set_feature(CoCo3_sdc_fix_os9_driver, FEATURE_5) // fix sdc query disk size issue in llcocosdc driver in multipak enviroment // `set_feature(CoCo3_sdc_fix_os9_driver,Feat_5) // fix sdc query disk size issue in llcocosdc driver in multipak enviroment
`define CoCo3_sdc_fix_os9_driver
`define Feat_5
`set_feature(CoCo3_disable_GART_in_GIMEX, FEATURE_6)// Disable GIMEX ram transfers [GIMEX detection in OS( EOU] // `set_feature(CoCo3_disable_GART_in_GIMEX,Feat_6) // Disable GIMEX ram transfers [GIMEX detection in OS9 EOU]
`define CoCo3_disable_GART_in_GIMEX
`define Feat_6
// `set_feature(,Feat_7) // Open Feature
// `define New_Feature...
// `define Feat_7
//`set_feature(CoCo3_enable_Music_Speech, FEATURE_7) // Enable Music and Speech cart
-123
View File
@@ -1,123 +0,0 @@
////////////////////////////////////////////////////////////////////////////////
// Project Name: CoCo3FPGA Version 5.x.x
// File Name: config_inc.v
//
// CoCo3 in an FPGA
//
////////////////////////////////////////////////////////////////////////////////
//
// CPU section copyrighted by John Kent
//
////////////////////////////////////////////////////////////////////////////////
//
// Color Computer 3 compatible system on a chip
//
// Version : 5.x
//
// Copyright (c) 2008 Gary Becker ([email protected])
//
// All rights reserved
//
// Redistribution and use in source and synthezised forms, with or without
// modification, are permitted provided that the following conditions are met:
//
// Redistributions of source code must retain the above copyright notice,
// this list of conditions and the following disclaimer.
//
// Redistributions in synthesized form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the distribution.
//
// Neither the name of the author nor the names of other contributors may
// be used to endorse or promote products derived from this software without
// specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
// THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
// PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
// CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
// POSSIBILITY OF SUCH DAMAGE.
//
// Please report bugs to the author, but before you do so, please
// make sure that this is not a derivative work and that
// you have the latest version of this file.
//
////////////////////////////////////////////////////////////////////////////////
// Gary Becker
// [email protected]
////////////////////////////////////////////////////////////////////////////////
////////////////////////////////////////////////////////////////////////////////
// MISTer Conversion by Stan Hodge and Alan Steremberg (& Gary Becker)
// [email protected]
//
////////////////////////////////////////////////////////////////////////////////
// This file is a configuration definition include file. The CoCo3FPGA for MiSTer source files
// can be built into multiple objects which have mutually exclusive features.
`define Config_Debug_Value (`config_num_1 | `config_num_2 | `config_num_3 | `config_num_4 | `config_num_5 | `config_num_6 | `config_num_7 | `config_num_8)
`define Config_Debug_FLAG 8'h55
`define FEATURE_1 8'h01
`define FEATURE_2 8'h02
`define FEATURE_3 8'h04
`define FEATURE_4 8'h08
`define FEATURE_5 8'h10
`define FEATURE_6 8'h20
`define FEATURE_7 8'h40
`define FEATURE_8 8'h80
`define config_num_1 8'h00
`define config_num_2 8'h00
`define config_num_3 8'h00
`define config_num_4 8'h00
`define config_num_5 8'h00
`define config_num_6 8'h00
`define config_num_7 8'h00
`define config_num_8 8'h00
`define set_feature(Feat_Name, Feat_Mask) \
`define Feat_Name \
`ifndef config_value_1 \
`define config_value_1 Feat_Mask \
`define config_num_1 Feat_Mask \
`else \
`ifndef config_value_2 \
`define config_value_2 Feat_Mask \
`define config_num_2 Feat_Mask \
`else \
`ifndef config_value_3 \
`define config_value_3 Feat_Mask \
`define config_num_3 Feat_Mask \
`else \
`ifndef config_value_4 \
`define config_value_4 Feat_Mask \
`define config_num_4 Feat_Mask \
`else \
`ifndef config_value_5 \
`define config_value_5 Feat_Mask \
`define config_num_5 Feat_Mask \
`else \
`ifndef config_value_6 \
`define config_value_6 Feat_Mask \
`define config_num_6 Feat_Mask \
`else \
`ifndef config_value_7 \
`define config_value_7 Feat_Mask \
`define config_num_7 Feat_Mask \
`else \
`ifndef config_value_8 \
`define config_value_8 Feat_Mask \
`define config_num_8 Feat_Mask \
`endif \
`endif \
`endif \
`endif \
`endif \
`endif \
`endif \
`endif
+213 -89
View File
@@ -135,6 +135,10 @@ wire [3:0] DRIVE_SEL_EXT_PRE = {DATA_IN[6], DATA_IN[2:0]};
reg [2:0] drive_index; reg [2:0] drive_index;
// SD blk system is a array of 4 systems - one for each drive. // SD blk system is a array of 4 systems - one for each drive.
// To keep disk track memory, we created 4 wd1793's to match the sd block interfaces
// For the interface back to the coco - we need to isolate the wd1793 the computer is talking
// to and route those feedback signals back to the coco. This is accomplished via the drive
// select. 'drive_index' identifies which controller is addressd.
always @(negedge FF40_CLK or negedge RESET_N) always @(negedge FF40_CLK or negedge RESET_N)
@@ -178,7 +182,7 @@ begin
4'b1001: 4'b1001:
drive_index <= 3'd1; drive_index <= 3'd1;
default: default:
drive_index <= 3'd0; // Illegal drive_index <= 3'd1; // Illegal
endcase endcase
end end
end end
@@ -208,12 +212,13 @@ wire DRQ[4];
wire selected_DRQ; wire selected_DRQ;
wire selected_INTRQ; wire selected_INTRQ;
wire WR; wire WR[4];
wire RD; wire RD[4];
wire RD_E; wire RD_E[4];
//wire CE; //wire CE;
wire HALT_EN_RST; wire HALT_EN_RST;
wire [7:0] DATA_1793; wire [7:0] DATA_1793;
wire [7:0] dout[4];
reg read; reg read;
reg write; reg write;
reg read_d; reg read_d;
@@ -225,7 +230,11 @@ reg read1;
reg write1; reg write1;
reg [1:0] ADDRESS_L; reg [1:0] ADDRESS_L;
assign RD = read || RD_E;
assign RD[0] = (read || RD_E[0]) && (drive_index == 2'd1);
assign RD[1] = (read || RD_E[1]) && (drive_index == 3'd2);
assign RD[2] = (read || RD_E[2]) && (drive_index == 3'd3);
assign RD[3] = (read || RD_E[3]) && (drive_index == 3'd4);
// The idea here is to "stretch" the CPU read and write signals to ensure we catch a 8 mhz enable. // The idea here is to "stretch" the CPU read and write signals to ensure we catch a 8 mhz enable.
// For writes we will buffer the data out to ensure it does not go away. // For writes we will buffer the data out to ensure it does not go away.
@@ -244,8 +253,14 @@ begin
write_d <= 1'b0; write_d <= 1'b0;
r_w_active <= 1'b0; r_w_active <= 1'b0;
clk_8Mhz_enable_found <= 1'b0; clk_8Mhz_enable_found <= 1'b0;
WR <= 1'b0; WR[0] <= 1'b0;
RD_E <= 1'b0; WR[1] <= 1'b0;
WR[2] <= 1'b0;
WR[3] <= 1'b0;
RD_E[0] <= 1'b0;
RD_E[1] <= 1'b0;
RD_E[2] <= 1'b0;
RD_E[3] <= 1'b0;
read1 <= 1'b0; read1 <= 1'b0;
write1 <= 1'b0; write1 <= 1'b0;
read <= 1'b0; read <= 1'b0;
@@ -278,14 +293,32 @@ begin
begin begin
// Set Writes // Set Writes
r_w_active <= 1'b1; r_w_active <= 1'b1;
WR <= 1'b1; case (drive_index)
3'd1:
WR[0] <= 1'b1;
3'd2:
WR[1] <= 1'b1;
3'd3:
WR[2] <= 1'b1;
3'd4:
WR[3] <= 1'b1;
endcase
end end
// Synchronus rising edge of read // Synchronus rising edge of read
if ((read == 1'b1) && (read_d == 1'b0)) if ((read == 1'b1) && (read_d == 1'b0))
begin begin
r_w_active <= 1'b1; r_w_active <= 1'b1;
RD_E <= 1'b1; case (drive_index)
3'd1:
RD_E[0] <= 1'b1;
3'd2:
RD_E[1] <= 1'b1;
3'd3:
RD_E[2] <= 1'b1;
3'd4:
RD_E[3] <= 1'b1;
endcase
end end
// Clears // Clears
@@ -298,54 +331,48 @@ begin
clk_8Mhz_enable_found <= 1'b0; clk_8Mhz_enable_found <= 1'b0;
r_w_active <= 1'b0; r_w_active <= 1'b0;
WR <= 1'b0; WR[0] <= 1'b0;
WR[1] <= 1'b0;
WR[2] <= 1'b0;
WR[3] <= 1'b0;
RD_E <= 1'b0; RD_E[0] <= 1'b0;
RD_E[1] <= 1'b0;
RD_E[2] <= 1'b0;
RD_E[3] <= 1'b0;
end end
end end
end end
// NMI from disk controller
// Selected INTRQ
assign selected_INTRQ = (drive_index == 3'd1) ? INTRQ[0]:
(drive_index == 3'd2) ? INTRQ[1]:
(drive_index == 3'd3) ? INTRQ[2]:
(drive_index == 3'd4) ? INTRQ[3]:
1'b0;
assign NMI_09 = DENSITY & selected_INTRQ; // Send NMI if Double Density (Halt Mode) assign NMI_09 = DENSITY & selected_INTRQ; // Send NMI if Double Density (Halt Mode)
// HALT from disk controller
// Selected DRQ
assign selected_DRQ = (drive_index == 3'd1) ? DRQ[0]:
(drive_index == 3'd2) ? DRQ[1]:
(drive_index == 3'd3) ? DRQ[2]:
(drive_index == 3'd4) ? DRQ[3]:
1'b1;
assign HALT = (HALT_EN & ~selected_DRQ); assign HALT = (HALT_EN & ~selected_DRQ);
assign HALT_EN_RST = RESET_N & ~selected_INTRQ; // From controller schematic assign HALT_EN_RST = RESET_N & ~selected_INTRQ; // From controller schematic
assign sd_lba[0] = wd1793_sd_lba; // Data bus selection
assign sd_lba[1] = wd1793_sd_lba; assign DATA_1793 = (drive_index == 3'd1) ? dout[0]:
assign sd_lba[2] = wd1793_sd_lba; (drive_index == 3'd2) ? dout[1]:
assign sd_lba[3] = wd1793_sd_lba; (drive_index == 3'd3) ? dout[2]:
(drive_index == 3'd4) ? dout[3]:
assign sd_rd[0] = (drive_index == 3'd1) ? wd1793_sd_rd: 8'd0;
1'b0;
assign sd_rd[1] = (drive_index == 3'd2) ? wd1793_sd_rd:
1'b0;
assign sd_rd[2] = (drive_index == 3'd3) ? wd1793_sd_rd:
1'b0;
assign sd_rd[3] = (drive_index == 3'd4) ? wd1793_sd_rd:
1'b0;
assign sd_wr[0] = (drive_index == 3'd1) ? wd1793_sd_wr:
1'b0;
assign sd_wr[1] = (drive_index == 3'd2) ? wd1793_sd_wr:
1'b0;
assign sd_wr[2] = (drive_index == 3'd3) ? wd1793_sd_wr:
1'b0;
assign sd_wr[3] = (drive_index == 3'd4) ? wd1793_sd_wr:
1'b0;
assign wd1793_sd_ack = (drive_index == 3'd1) ? sd_ack[0]:
(drive_index == 3'd2) ? sd_ack[1]:
(drive_index == 3'd3) ? sd_ack[2]:
(drive_index == 3'd4) ? sd_ack[3]:
sd_ack[0]; // default is drive 1
assign sd_buff_din[0] = wd1793_sd_buff_din;
assign sd_buff_din[1] = wd1793_sd_buff_din;
assign sd_buff_din[2] = wd1793_sd_buff_din;
assign sd_buff_din[3] = wd1793_sd_buff_din;
// The SD_BLK interface and thus the wd1793 will allways transfer 1 blk. This is blk qty - 1 per spec. // The SD_BLK interface and thus the wd1793 will allways transfer 1 blk. This is blk qty - 1 per spec.
@@ -358,13 +385,6 @@ reg drive_wp[4];
reg [3:0] drive_ready = 4'B0000; reg [3:0] drive_ready = 4'B0000;
reg [3:0] double_sided = 4'B0000; reg [3:0] double_sided = 4'B0000;
reg [23:0] drive_size[4]; reg [23:0] drive_size[4];
wire [23:0] selected_drive_size;
wire [31:0] wd1793_sd_lba;
wire wd1793_sd_rd;
wire wd1793_sd_wr;
wire wd1793_sd_ack;
wire [7:0] wd1793_sd_buff_din;
wire selected_drive_ready, selected_drive_wp, selected_double_sided;
// As drives are mounted in MISTer this logic saves the write protect and generates ready for // As drives are mounted in MISTer this logic saves the write protect and generates ready for
@@ -413,28 +433,6 @@ begin
//double_sided[3]<= img_size > 20'd368600;//20'd368640; //double_sided[3]<= img_size > 20'd368600;//20'd368640;
end end
assign selected_drive_size = (drive_index == 3'd1) ? drive_size[0]:
(drive_index == 3'd2) ? drive_size[1]:
(drive_index == 3'd3) ? drive_size[2]:
(drive_index == 3'd4) ? drive_size[3]:
drive_size[0]; // default is drive 1
assign selected_drive_wp = (drive_index == 3'd1) ? drive_wp[0]:
(drive_index == 3'd2) ? drive_wp[1]:
(drive_index == 3'd3) ? drive_wp[2]:
(drive_index == 3'd4) ? drive_wp[3]:
drive_wp[0]; // default is drive 1
assign selected_double_sided= (drive_index == 3'd1) ? double_sided[0]:
(drive_index == 3'd2) ? double_sided[1]:
(drive_index == 3'd3) ? double_sided[2]:
double_sided[0]; // default is drive 1
assign selected_drive_ready = (drive_index == 3'd1) ? drive_ready[0]:
(drive_index == 3'd2) ? drive_ready[1]:
(drive_index == 3'd3) ? drive_ready[2]:
(drive_index == 3'd4) ? drive_ready[3]:
1'b0; // default is not ready
wd1793 #(1,0) coco_wd1793_0 wd1793 #(1,0) coco_wd1793_0
( (
@@ -442,34 +440,160 @@ wd1793 #(1,0) coco_wd1793_0
.ce(ena_8Mhz), .ce(ena_8Mhz),
.reset(~RESET_N), .reset(~RESET_N),
.io_en(1'b1), .io_en(1'b1),
.rd(RD), .rd(RD[0]),
.wr(WR), .wr(WR[0]),
.addr(ADDRESS_L[1:0]), .addr(ADDRESS_L[1:0]),
.din(DATA_IN_L), .din(DATA_IN_L),
.dout(DATA_1793), .dout(dout[0]),
.drq(selected_DRQ), .drq(DRQ[0]),
.intrq(selected_INTRQ), .intrq(INTRQ[0]),
.img_mounted(1'b0), .img_mounted(1'b0),
.img_mounted_overide(1'b1), .img_mounted_overide(1'b1),
.img_size(selected_drive_size[19:0]), .img_size(drive_size[0]),
.sd_lba(wd1793_sd_lba), .sd_lba(sd_lba[0]),
.sd_rd(wd1793_sd_rd), .sd_rd(sd_rd[0]),
.sd_wr(wd1793_sd_wr), .sd_wr(sd_wr[0]),
.sd_ack(wd1793_sd_ack), .sd_ack(sd_ack[0]),
.sd_buff_addr(sd_buff_addr), .sd_buff_addr(sd_buff_addr),
.sd_buff_dout(sd_buff_dout), .sd_buff_dout(sd_buff_dout),
.sd_buff_din(wd1793_sd_buff_din), .sd_buff_din(sd_buff_din[0]),
.sd_buff_wr(sd_buff_wr), .sd_buff_wr(sd_buff_wr),
.wp(selected_drive_wp), .wp(drive_wp[0]),
.size_code(3'd5), // 5 is 18 sector x 256 bits COCO standard .size_code(3'd5), // 5 is 18 sector x 256 bits COCO standard
.layout(~selected_double_sided), // 0 = Track-Side-Sector, 1 - Side-Track-Sector .layout(~double_sided[0]), // 0 = Track-Side-Sector, 1 - Side-Track-Sector
.side(selected_double_sided & DRIVE_SEL_EXT[3]), .side(double_sided[0] & DRIVE_SEL_EXT[3]),
.ready(selected_drive_ready), .ready(drive_ready[0]),
.input_active(0), // Section not used
.input_addr(0),
.input_data(0),
.input_wr(0),
.buff_din(0)
);
wd1793 #(1,0) coco_wd1793_1
(
.clk_sys(~CLK),
.ce(ena_8Mhz),
.reset(~RESET_N),
.io_en(1'b1),
.rd(RD[1]),
.wr(WR[1]),
.addr(ADDRESS_L[1:0]),
.din(DATA_IN_L),
.dout(dout[1]),
.drq(DRQ[1]),
.intrq(INTRQ[1]),
.img_mounted(1'b0),
.img_mounted_overide(1'b1),
.img_size(drive_size[1]),
.sd_lba(sd_lba[1]),
.sd_rd(sd_rd[1]),
.sd_wr(sd_wr[1]),
.sd_ack(sd_ack[1]),
.sd_buff_addr(sd_buff_addr),
.sd_buff_dout(sd_buff_dout),
.sd_buff_din(sd_buff_din[1]),
.sd_buff_wr(sd_buff_wr),
.wp(drive_wp[1]),
.size_code(3'd5), // 5 is 18 sector x 256 bits COCO standard
.layout(~double_sided[1]), // 0 = Track-Side-Sector, 1 - Side-Track-Sector
.side(double_sided[1] & DRIVE_SEL_EXT[3]),
.ready(drive_ready[1]),
.input_active(0), // Section not used
.input_addr(0),
.input_data(0),
.input_wr(0),
.buff_din(0)
);
wd1793 #(1,0) coco_wd1793_2
(
.clk_sys(~CLK),
.ce(ena_8Mhz),
.reset(~RESET_N),
.io_en(1'b1),
.rd(RD[2]),
.wr(WR[2]),
.addr(ADDRESS_L[1:0]),
.din(DATA_IN_L),
.dout(dout[2]),
.drq(DRQ[2]),
.intrq(INTRQ[2]),
.img_mounted(1'b0),
.img_mounted_overide(1'b1),
.img_size(drive_size[2]),
.sd_lba(sd_lba[2]),
.sd_rd(sd_rd[2]),
.sd_wr(sd_wr[2]),
.sd_ack(sd_ack[2]),
.sd_buff_addr(sd_buff_addr),
.sd_buff_dout(sd_buff_dout),
.sd_buff_din(sd_buff_din[2]),
.sd_buff_wr(sd_buff_wr),
.wp(drive_wp[2]),
.size_code(3'd5), // 5 is 18 sector x 256 bits COCO standard
.layout(~double_sided[2]), // 0 = Track-Side-Sector, 1 - Side-Track-Sector
.side(double_sided[2] & DRIVE_SEL_EXT[3]),
.ready(drive_ready[2]),
.input_active(0), // Section not used
.input_addr(0),
.input_data(0),
.input_wr(0),
.buff_din(0)
);
wd1793 #(1,0) coco_wd1793_3
(
.clk_sys(~CLK),
.ce(ena_8Mhz),
.reset(~RESET_N),
.io_en(1'b1),
.rd(RD[3]),
.wr(WR[3]),
.addr(ADDRESS_L[1:0]),
.din(DATA_IN_L),
.dout(dout[3]),
.drq(DRQ[3]),
.intrq(INTRQ[3]),
.img_mounted(1'b0),
.img_mounted_overide(1'b1),
.img_size(drive_size[3]),
.sd_lba(sd_lba[3]),
.sd_rd(sd_rd[3]),
.sd_wr(sd_wr[3]),
.sd_ack(sd_ack[3]),
.sd_buff_addr(sd_buff_addr),
.sd_buff_dout(sd_buff_dout),
.sd_buff_din(sd_buff_din[3]),
.sd_buff_wr(sd_buff_wr),
.wp(drive_wp[3]),
.size_code(3'd5), // 5 is 18 sector x 256 bits COCO standard
.layout(1'b1), // 0 = Track-Side-Sector, 1 - Side-Track-Sector
.side(1'b0),
.ready(drive_ready[3]),
.input_active(0), // Section not used .input_active(0), // Section not used
.input_addr(0), .input_addr(0),
-203
View File
@@ -1,203 +0,0 @@
////////////////////////////////////////////////////////////////////////////////
// Project Name: CoCo3FPGA Version 5.x.x
// File Name: Music_Speech.sv
//
// CoCo3 in an FPGA
//
////////////////////////////////////////////////////////////////////////////////
//
////////////////////////////////////////////////////////////////////////////////
//
// Color Computer 3 compatible system on a chip
//
//
// Copyright (c) 2008 Gary Becker ([email protected])
//
// All rights reserved
//
// Redistribution and use in source and synthezised forms, with or without
// modification, are permitted provided that the following conditions are met:
//
// Redistributions of source code must retain the above copyright notice,
// this list of conditions and the following disclaimer.
//
// Redistributions in synthesized form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the distribution.
//
// Neither the name of the author nor the names of other contributors may
// be used to endorse or promote products derived from this software without
// specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
// THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
// PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
// CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
// POSSIBILITY OF SUCH DAMAGE.
//
// Please report bugs to the author, but before you do so, please
// make sure that this is not a derivative work and that
// you have the latest version of this file.
//
//
////////////////////////////////////////////////////////////////////////////////
// Stan Hodge
//
// Music_Speech.sv by Stan Hodge 02/16/24
////////////////////////////////////////////////////////////////////////////////
module Music_Speech(
input RESET_N,
input CLK,
input CLK_EN,
input CLK_1_78,
input [1:0] MPI_SCS, // slot id
input [15:0] ADDRESS, // from 09
input [7:0] WRITE_DATA, // from 09
output [7:0] READ_DATA, // to 09
input RW_N, // from 09
output [7:0] AUDIO // 8 bit audio output mixed from both Speech and Music chips
);
///////////////////////////////////////////////////////
// Host Interface
localparam Soft_Reset_Adrs = 15'hff7d;
localparam Data_Write_Adrs = 15'hff7e;
localparam SLOT_1 = 2'b00; // Nothing [RS-232)
localparam SLOT_2 = 2'b01; // SDC
localparam SLOT_3 = 2'b10; // Cartridge System
localparam SLOT_4 = 2'b11; // FDC
localparam S_M_SLOT = SLOT_2;
reg Soft_Reset;
wire System_Reset;
// Soft Reset Bit
always @ (negedge CLK or negedge RESET_N)
begin
if(!RESET_N)
begin
Soft_Reset <= 1'b0;
end
else
begin
if (CLK_EN && !RW_N && (MPI_SCS == S_M_SLOT) && (ADDRESS == Soft_Reset_Adrs))
begin
if (WRITE_DATA[0])
Soft_Reset <= !Soft_Reset;
else
Soft_Reset <= 1'b0;
end
end
end
assign System_Reset = RESET_N ^ Soft_Reset;
// New data and INT
reg INT3_N;
reg [7:0] SOC_WR_DATA;
always @ (negedge CLK or negedge Port_C[7])
begin
if(!Port_C[7])
begin
INT3_N <= 1'b1;
end
else
begin
if (CLK_EN && !RW_N && (MPI_SCS == S_M_SLOT) && (ADDRESS == Data_Write_Adrs))
begin
SOC_WR_DATA <= WRITE_DATA;
INT3_N <= 1'b0;
end
end
end
//////////////////////////////////////////////////////////////////////////////
// Read Data
wire Speech_Status;
wire Music_Status;
assign READ_DATA = {INT3_N, Speech_Status, Music_Status, 5'b00000};
/////////////////////////////////////////////////////////////////////////////
// SOC
wire INT1_N;
wire [7:0] Port_A, Port_B, Port_C, Port_D_IN, Port_D_OUT;
Music_Speech_SOC CoCo3_Music_Speech_SOC(
.RESET_N(RESET_N),
.CLKIN(CLK),
.CLK_1_78(CLK_1_78),
.INT1_N(INT1_N),
.INT3_N(INT3_N),
.PORT_A(Port_A),
.PORT_B(Port_B),
.PORT_C(Port_C),
.PORT_D_OUT(Port_D_OUT),
.PORT_D_IN(Port_D_IN)
);
/////////////////////////////////////////////////////////////////////////////
// SRAM Chip
COCO_SRAM_6116 CoCo3_SRAM_6116(
.CLK(CLK),
.ADDR({Port_C[2:0], Port_B}), // Check
.R_N(Port_C[4]), // Check
.DATA_O(Port_D_IN),
.DATA_I(Port_D_OUT)
);
/////////////////////////////////////////////////////////////////////////////
// Speech Chip
sp0256 CoCo3_sp0256(
.clock(),
.ce(),
.reset(),
.input_rdy(),
.allophone(),
.trig_allophone(),
.audio_out()
);
/////////////////////////////////////////////////////////////////////////////
// Music Chip
ym2149_audio CoCo3_ym2149_audio(
.clk_i(CLK),
.en_clk_psg_i(CLK_1_78),
.sel_n_i(1'b1), // No divide by 2
.reset_n_i(RESET_N),
.bc_i(),
.bdir_i(),
.data_i(),
.data_r_o(),
// .ch_a_o(),
// .ch_b_o(),
// .ch_c_o()
.mix_audio_o(), //[13:0]
// .pcm14s_o()
);
endmodule
+3 -2
View File
@@ -47,8 +47,6 @@
//////////////////////////////////////////////////////////////////////////////// ////////////////////////////////////////////////////////////////////////////////
//////////////////////////////////////////////////////////////////////////////// ////////////////////////////////////////////////////////////////////////////////
// Define Config features
`include "../RTL/config.v"
module sdc( module sdc(
input CLK, // clock input CLK, // clock
@@ -89,6 +87,9 @@ module sdc(
); );
// Define Config features
`include "../rtl/config.sv"
reg [23:0] LSN; reg [23:0] LSN;
reg [7:0] command; reg [7:0] command;
reg [7:0] transfer_address; reg [7:0] transfer_address;
+107 -74
View File
@@ -146,54 +146,27 @@ assign DATA_HDD =
wire [31:0] sdc_sd_lba[2]; wire [31:0] sdc_sd_lba[2];
wire [31:0] fdc_sd_lba[2]; wire [31:0] fdc_sd_lba[2];
wire [31:0] wd1793_sd_lba;
wire [1:0] sdc_sd_rd; wire [1:0] sdc_sd_rd;
wire wd1793_sd_rd;
wire [1:0] fdc_sd_rd; wire [1:0] fdc_sd_rd;
wire [1:0] sdc_sd_wr; wire [1:0] sdc_sd_wr;
wire [1:0] fdc_sd_wr; wire [1:0] fdc_sd_wr;
wire wd1793_sd_wr;
wire [7:0] sdc_sd_buff_din[2]; wire [7:0] sdc_sd_buff_din[2];
wire [7:0] fdc_sd_buff_din[2]; wire [7:0] fdc_sd_buff_din[2];
wire [7:0] wd1793_sd_buff_din; wire [7:0] wd1793_sd_buff_din;
wire wd1793_sd_ack;
wire sdc_HALT; wire sdc_HALT;
assign sd_lba[0:1] = SDC_EN ? sdc_sd_lba[0:1]: assign sd_lba[0:1] = SDC_EN ? sdc_sd_lba[0:1]:
fdc_sd_lba[0:1]; fdc_sd_lba[0:1];
assign fdc_sd_lba[0] = wd1793_sd_lba;
assign fdc_sd_lba[1] = wd1793_sd_lba;
assign sd_rd[1:0] = SDC_EN ? sdc_sd_rd[1:0]: assign sd_rd[1:0] = SDC_EN ? sdc_sd_rd[1:0]:
fdc_sd_rd[1:0]; fdc_sd_rd[1:0];
assign fdc_sd_rd[0] = (drive_index == 3'd1) ? wd1793_sd_rd:
1'b0;
assign fdc_sd_rd[1] = (drive_index == 3'd2) ? wd1793_sd_rd:
1'b0;
assign sd_wr[1:0] = SDC_EN ? sdc_sd_wr[1:0]: assign sd_wr[1:0] = SDC_EN ? sdc_sd_wr[1:0]:
fdc_sd_wr[1:0]; fdc_sd_wr[1:0];
assign fdc_sd_wr[0] = (drive_index == 3'd1) ? wd1793_sd_wr:
1'b0;
assign fdc_sd_wr[1] = (drive_index == 3'd2) ? wd1793_sd_wr:
1'b0;
assign sd_buff_din[0:1] = SDC_EN ? sdc_sd_buff_din[0:1]: assign sd_buff_din[0:1] = SDC_EN ? sdc_sd_buff_din[0:1]:
fdc_sd_buff_din[0:1]; fdc_sd_buff_din[0:1];
assign fdc_sd_buff_din[0] = wd1793_sd_buff_din;
assign fdc_sd_buff_din[1] = wd1793_sd_buff_din;
assign wd1793_sd_ack = (drive_index == 3'd1) ? sd_ack[0]:
(drive_index == 3'd2) ? sd_ack[1]:
sd_ack[0]; // default is drive 1
sdc coco_sdc( sdc coco_sdc(
.CLK(CLK), // clock .CLK(CLK), // clock
@@ -277,13 +250,13 @@ begin
drive_index <= 3'd1; drive_index <= 3'd1;
4'b1011: // This is what the Magic Number $43 does so we select a non-active drive 4'b1011: // This is what the Magic Number $43 does so we select a non-active drive
drive_index <= 3'd0; drive_index <= 3'd1;
4'b1000: // This is no drive with DS = illegal drive 4'b1000: // This is no drive with DS = illegal drive
drive_index <= 3'd0; drive_index <= 3'd1;
4'b0000: // This is no drive (maybe 0 in ff40) = illegal drive 4'b0000: // This is no drive (maybe 0 in ff40) = illegal drive
drive_index <= 3'd0; drive_index <= 3'd1;
default: default:
drive_index <= 3'd0; drive_index <= 3'd1;
endcase endcase
end end
end end
@@ -310,14 +283,17 @@ end
// Control signals for the wd1793 // Control signals for the wd1793
wire INTRQ[2];
wire DRQ[2];
wire selected_DRQ; wire selected_DRQ;
wire selected_INTRQ; wire selected_INTRQ;
wire WR; wire WR[2];
wire RD; wire RD[2];
wire RD_E; wire RD_E[2];
wire HALT_EN_RST; wire HALT_EN_RST;
wire [7:0] DATA_1793; wire [7:0] DATA_1793;
wire [7:0] dout[2];
reg read; reg read;
reg write; reg write;
reg read_d; reg read_d;
@@ -329,7 +305,8 @@ reg read1;
reg write1; reg write1;
reg [1:0] ADDRESS_L; reg [1:0] ADDRESS_L;
assign RD = (read || RD_E); // Even with no drive selected allow read to the controller assign RD[0] = (read || RD_E[0]) && (drive_index == 2'd1);
assign RD[1] = (read || RD_E[1]) && (drive_index == 3'd2);
// The idea here is to "stretch" the CPU read and write signals to ensure we catch a 8 mhz enable. // The idea here is to "stretch" the CPU read and write signals to ensure we catch a 8 mhz enable.
// For writes we will buffer the data out to ensure it does not go away. // For writes we will buffer the data out to ensure it does not go away.
@@ -350,8 +327,10 @@ begin
write_d <= 1'b0; write_d <= 1'b0;
r_w_active <= 1'b0; r_w_active <= 1'b0;
clk_8Mhz_enable_found <= 1'b0; clk_8Mhz_enable_found <= 1'b0;
WR <= 1'b0; WR[0] <= 1'b0;
RD_E <= 1'b0; WR[1] <= 1'b0;
RD_E[0] <= 1'b0;
RD_E[1] <= 1'b0;
read1 <= 1'b0; read1 <= 1'b0;
write1 <= 1'b0; write1 <= 1'b0;
read <= 1'b0; read <= 1'b0;
@@ -383,14 +362,24 @@ begin
begin begin
// Set Write // Set Write
r_w_active <= 1'b1; r_w_active <= 1'b1;
WR <= 1'b1; case (drive_index)
3'd1:
WR[0] <= 1'b1;
3'd2:
WR[1] <= 1'b1;
endcase
end end
// Synchronus rising edge of read // Synchronus rising edge of read
if ((read == 1'b1) && (read_d == 1'b0)) if ((read == 1'b1) && (read_d == 1'b0))
begin begin
r_w_active <= 1'b1; r_w_active <= 1'b1;
RD_E <= 1'b1; case (drive_index)
3'd1:
RD_E[0] <= 1'b1;
3'd2:
RD_E[1] <= 1'b1;
endcase
end end
// Clears // Clears
@@ -402,23 +391,42 @@ begin
begin begin
clk_8Mhz_enable_found <= 1'b0; clk_8Mhz_enable_found <= 1'b0;
r_w_active <= 1'b0; r_w_active <= 1'b0;
WR <= 1'b0; WR[0] <= 1'b0;
RD_E <= 1'b0; WR[1] <= 1'b0;
RD_E[0] <= 1'b0;
RD_E[1] <= 1'b0;
end end
end end
end end
// NMI from disk controller // NMI from disk controller
// Selected INTRQ
assign selected_INTRQ = (drive_index == 3'd1) ? INTRQ[0]:
(drive_index == 3'd2) ? INTRQ[1]:
1'b0;
assign NMI_09 = ~SDC_EN & DENSITY & selected_INTRQ; // Send NMI if Double Density (Halt Mode) assign NMI_09 = ~SDC_EN & DENSITY & selected_INTRQ; // Send NMI if Double Density (Halt Mode)
// HALT from disk controller // HALT from disk controller
// Selected DRQ
assign selected_DRQ = (drive_index == 3'd1) ? DRQ[0]:
(drive_index == 3'd2) ? DRQ[1]:
1'b1;
assign HALT = (~SDC_EN & HALT_EN & ~selected_DRQ) | sdc_HALT; assign HALT = (~SDC_EN & HALT_EN & ~selected_DRQ) | sdc_HALT;
assign HALT_EN_RST = RESET_N & ~selected_INTRQ; // From controller schematic assign HALT_EN_RST = RESET_N & ~selected_INTRQ; // From controller schematic
// Data bus selection
assign DATA_1793 = (drive_index == 3'd1) ? dout[0]:
(drive_index == 3'd2) ? dout[1]:
8'd0;
// The SD_BLK interface and thus the wd1793 will allways transfer 1 blk. This is blk qty - 1 per spec. // The SD_BLK interface and thus the wd1793 will allways transfer 1 blk. This is blk qty - 1 per spec.
assign sd_blk_cnt[1] = 6'd0; assign sd_blk_cnt[1] = 6'd0;
@@ -428,8 +436,6 @@ reg drive_wp[2];
reg [1:0] drive_ready = 2'b00; reg [1:0] drive_ready = 2'b00;
reg [1:0] double_sided = 2'b00; reg [1:0] double_sided = 2'b00;
reg [31:0] drive_size[2]; reg [31:0] drive_size[2];
wire [31:0] selected_drive_size;
wire selected_drive_ready, selected_drive_wp, selected_double_sided;
// As drives are mounted in MISTer this logic saves the write protect and generates ready for // As drives are mounted in MISTer this logic saves the write protect and generates ready for
// changing drives to the wd1793. // changing drives to the wd1793.
@@ -457,56 +463,83 @@ begin
double_sided[1]<= (img_size > 64'd368600) & (img_size < 64'd740000);//20'd368640; double_sided[1]<= (img_size > 64'd368600) & (img_size < 64'd740000);//20'd368640;
end end
assign selected_drive_size = (drive_index == 3'd1) ? drive_size[0]:
(drive_index == 3'd2) ? drive_size[1]:
drive_size[0]; // default is drive 1
assign selected_drive_wp = (drive_index == 3'd1) ? drive_wp[0]: wd1793 #(1,0) coco_wd1793_sdc_0
(drive_index == 3'd2) ? drive_wp[1]:
drive_wp[0]; // default is drive 1
assign selected_double_sided= (drive_index == 3'd1) ? double_sided[0]:
(drive_index == 3'd2) ? double_sided[1]:
double_sided[0]; // default is drive 1
assign selected_drive_ready = (drive_index == 3'd1) ? drive_ready[0]:
(drive_index == 3'd2) ? drive_ready[1]:
drive_ready[0]; // default is drive 1
wd1793 #(1,0) coco_wd1793_sdc
( (
.clk_sys(~CLK), .clk_sys(~CLK),
.ce(ena_8Mhz), .ce(ena_8Mhz),
.reset(~RESET_N), .reset(~RESET_N),
.io_en(1'b1), .io_en(1'b1),
.rd(RD), .rd(RD[0]),
.wr(WR), .wr(WR[0]),
.addr(ADDRESS_L[1:0]), .addr(ADDRESS_L[1:0]),
.din(DATA_IN_L), .din(DATA_IN_L),
.dout(DATA_1793), .dout(dout[0]),
.drq(selected_DRQ), .drq(DRQ[0]),
.intrq(selected_INTRQ), .intrq(INTRQ[0]),
.img_mounted(1'b0), // Not used when using _override .img_mounted(1'b0), // Not used when using _override
.img_mounted_overide(1'b1), // Load img_size and layout on each clock .img_mounted_overide(1'b1), // Load img_size and layout on each clock
.img_size(selected_drive_size[19:0]), .img_size(drive_size[0]),
.sd_lba(wd1793_sd_lba), .sd_lba(fdc_sd_lba[0]),
.sd_rd(wd1793_sd_rd), .sd_rd(fdc_sd_rd[0]),
.sd_wr(wd1793_sd_wr), .sd_wr(fdc_sd_wr[0]),
.sd_ack(wd1793_sd_ack), .sd_ack(sd_ack[0]),
.sd_buff_addr(sd_buff_addr), .sd_buff_addr(sd_buff_addr),
.sd_buff_dout(sd_buff_dout), .sd_buff_dout(sd_buff_dout),
.sd_buff_din(wd1793_sd_buff_din), .sd_buff_din(fdc_sd_buff_din[0]),
.sd_buff_wr(sd_buff_wr), .sd_buff_wr(sd_buff_wr),
.wp(selected_drive_wp), .wp(drive_wp[0]),
.size_code(3'd5), // 5 is 18 sector x 256 bits COCO standard .size_code(3'd5), // 5 is 18 sector x 256 bits COCO standard
.layout(~selected_double_sided), // 0 = Track-Side-Sector, 1 - Side-Track-Sector .layout(~double_sided[0]), // 0 = Track-Side-Sector, 1 - Side-Track-Sector
.side(selected_double_sided & DRIVE_SEL_EXT[3]), .side(double_sided[0] & DRIVE_SEL_EXT[3]),
.ready(selected_drive_ready), .ready(drive_ready[0]),
.input_active(0), // Section not used
.input_addr(0),
.input_data(0),
.input_wr(0),
.buff_din(0)
);
wd1793 #(1,0) coco_wd1793_sdc_1
(
.clk_sys(~CLK),
.ce(ena_8Mhz),
.reset(~RESET_N),
.io_en(1'b1),
.rd(RD[1]),
.wr(WR[1]),
.addr(ADDRESS_L[1:0]),
.din(DATA_IN_L),
.dout(dout[1]),
.drq(DRQ[1]),
.intrq(INTRQ[1]),
.img_mounted(1'b0), // Not used when using _override
.img_mounted_overide(1'b1), // Load img_size and layout on each clock
.img_size(drive_size[1]),
.sd_lba(fdc_sd_lba[1]),
.sd_rd(fdc_sd_rd[1]),
.sd_wr(fdc_sd_wr[1]),
.sd_ack(sd_ack[1]),
.sd_buff_addr(sd_buff_addr),
.sd_buff_dout(sd_buff_dout),
.sd_buff_din(fdc_sd_buff_din[1]),
.sd_buff_wr(sd_buff_wr),
.wp(drive_wp[1]),
.size_code(3'd5), // 5 is 18 sector x 256 bits COCO standard
.layout(~double_sided[1]), // 0 = Track-Side-Sector, 1 - Side-Track-Sector
.side(double_sided[1] & DRIVE_SEL_EXT[3]),
.ready(drive_ready[1]),
.input_active(0), // Section not used .input_active(0), // Section not used
.input_addr(0), .input_addr(0),
-103
View File
@@ -1,103 +0,0 @@
--//////////////////////////////////////////////////////////////////////////////
-- Project Name: CoCo3FPGA Version 4.0
-- File Name: CoCo_ram_128x8.vhd
--
-- CoCo3 in an FPGA
--
-- Revision: 5.x.x
--//////////////////////////////////////////////////////////////////////////////
--
-- Color Computer 3 compatible system on a chip
--
-- Version : 5.0.x.x
--
-- Copyright (c) 2008 Gary Becker ([email protected])
--
-- All rights reserved
--
-- Redistribution and use in source and synthezised forms, with or without
-- modification, are permitted provided that the following conditions are met:
--
-- Redistributions of source code must retain the above copyright notice,
-- this list of conditions and the following disclaimer.
--
-- Redistributions in synthesized form must reproduce the above copyright
-- notice, this list of conditions and the following disclaimer in the
-- documentation and/or other materials provided with the distribution.
--
-- Neither the name of the author nor the names of other contributors may
-- be used to endorse or promote products derived from this software without
-- specific prior written permission.
--
-- THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
-- AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-- THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-- PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE
-- LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
-- CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
-- SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
-- INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
-- CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
-- ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
-- POSSIBILITY OF SUCH DAMAGE.
--
-- Please report bugs to the author, but before you do so, please
-- make sure that this is not a derivative work and that
-- you have the latest version of this file.
--
-- The latest version of this file can be found at:
-- http://groups.yahoo.com/group/CoCo3FPGA
--
-- File history :
--
-- 1.0 Full Release
-- 2.0 Partial Release
-- 3.0 Full Release
-- 3.0.0.1 Update to fix DoD interrupt issue
--//////////////////////////////////////////////////////////////////////////////
-- Gary Becker
-- [email protected]
--//////////////////////////////////////////////////////////////////////////////
--//////////////////////////////////////////////////////////////////////////////
--////////////////////////////////////////////////////////////////////////////////
--// MISTer Conversion by Stan Hodge and Alan Steremberg (& Gary Becker)
--// [email protected]
--//
--////////////////////////////////////////////////////////////////////////////////
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
use ieee.numeric_std.all;
entity COCO_SRAM_6116 is
port (
CLK : in std_logic;
ENA : in std_logic;
ADDR : in std_logic_vector(6 downto 0);
R_W : in std_logic;
DATA_I : in std_logic_vector(7 downto 0);
DATA_O : out std_logic_vector(7 downto 0)
);
end;
architecture RTL of COCO_SRAM_128x8 is
type SRAM_ARRAY is array(0 to 127) of std_logic_vector(7 downto 0);
signal SRAM : SRAM_ARRAY;
begin
P_SRAM : process(CLK,ADDR,R_W,DATA_I)
begin
if CLK'event and CLK='1' then
if ENA = '1' and R_W = '0' then
SRAM(to_integer(unsigned(ADDR))) <= DATA_I;
end if;
end if;
end process;
DATA_O <= SRAM(to_integer(unsigned(ADDR)));
end RTL;
-102
View File
@@ -1,102 +0,0 @@
--//////////////////////////////////////////////////////////////////////////////
-- Project Name: CoCo3FPGA Version 4.0
-- File Name: CoCo_ram_6116.vhd
--
-- CoCo3 in an FPGA
--
-- Revision: 4.0 07/10/16
--//////////////////////////////////////////////////////////////////////////////
--
-- Color Computer 3 compatible system on a chip
--
-- Version : 5.0.x.x
--
-- Copyright (c) 2008 Gary Becker ([email protected])
--
-- All rights reserved
--
-- Redistribution and use in source and synthezised forms, with or without
-- modification, are permitted provided that the following conditions are met:
--
-- Redistributions of source code must retain the above copyright notice,
-- this list of conditions and the following disclaimer.
--
-- Redistributions in synthesized form must reproduce the above copyright
-- notice, this list of conditions and the following disclaimer in the
-- documentation and/or other materials provided with the distribution.
--
-- Neither the name of the author nor the names of other contributors may
-- be used to endorse or promote products derived from this software without
-- specific prior written permission.
--
-- THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
-- AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-- THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-- PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE
-- LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
-- CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
-- SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
-- INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
-- CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
-- ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
-- POSSIBILITY OF SUCH DAMAGE.
--
-- Please report bugs to the author, but before you do so, please
-- make sure that this is not a derivative work and that
-- you have the latest version of this file.
--
-- The latest version of this file can be found at:
-- http://groups.yahoo.com/group/CoCo3FPGA
--
-- File history :
--
-- 1.0 Full Release
-- 2.0 Partial Release
-- 3.0 Full Release
-- 3.0.0.1 Update to fix DoD interrupt issue
--//////////////////////////////////////////////////////////////////////////////
-- Gary Becker
-- [email protected]
--//////////////////////////////////////////////////////////////////////////////
--//////////////////////////////////////////////////////////////////////////////
--////////////////////////////////////////////////////////////////////////////////
--// MISTer Conversion by Stan Hodge and Alan Steremberg (& Gary Becker)
--// [email protected]
--//
--////////////////////////////////////////////////////////////////////////////////
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
use ieee.numeric_std.all;
entity COCO_SRAM_6116 is
port (
CLK : in std_logic;
ADDR : in std_logic_vector(10 downto 0);
R_W : in std_logic;
DATA_I : in std_logic_vector(7 downto 0);
DATA_O : out std_logic_vector(7 downto 0)
);
end;
architecture RTL of COCO_SRAM_6116 is
type SRAM_ARRAY is array(0 to 2047) of std_logic_vector(7 downto 0);
signal SRAM : SRAM_ARRAY;
begin
P_SRAM : process(CLK,ADDR,R_W,DATA_I)
begin
if CLK'event and CLK='1' then
if R_W = '0' then
SRAM(to_integer(unsigned(ADDR))) <= DATA_I;
end if;
end if;
end process;
DATA_O <= SRAM(to_integer(unsigned(ADDR)));
end RTL;
+11 -2
View File
@@ -99,6 +99,11 @@ reg [1:0] wd_size_code;
wire [7:0] buff_dout; wire [7:0] buff_dout;
reg [1:0] sd_block = 0; reg [1:0] sd_block = 0;
reg format; reg format;
// buff_wr is assigned from always blocks outside the `generate if(RWMODE)`
// block it used to be declared in (after the wd1793_dpram that reads it). Those
// assignments then resolve to a separate implicit net in Verilator, so the
// sector-buffer write strobe never reached the RAM. Declared here instead.
reg buff_wr;
generate generate
if(RWMODE) begin if(RWMODE) begin
wd1793_dpram sbuf wd1793_dpram sbuf
@@ -115,7 +120,6 @@ generate
.wren_b(wre & buff_wr & (addr == A_DATA) & ~scan_active), .wren_b(wre & buff_wr & (addr == A_DATA) & ~scan_active),
.q_b(buff_dout) .q_b(buff_dout)
); );
reg buff_wr;
end else begin end else begin
assign buff_dout = 0; assign buff_dout = 0;
assign sd_buff_din = 0; assign sd_buff_din = 0;
@@ -788,13 +792,18 @@ wire[10:0] edsk_next = ((edsk_addr + 1'd1) >= edsk_size) ? 11'd0 : edsk_addr + 1
reg [7:0] spt_size = 0; reg [7:0] spt_size = 0;
// spt_addr is assigned from the always block above, outside the
// `generate if(EDSK)` scope it used to be declared in. Quartus tolerates that,
// but Verilator rejects it ("Can't find definition of variable: 'spt_addr'"),
// so it lives at module scope, next to spt_size. No behavioural change.
reg [7:0] spt_addr;
generate generate
if(EDSK) begin if(EDSK) begin
wire [7:0] scan_data = RWMODE ? buff_dout : input_data; wire [7:0] scan_data = RWMODE ? buff_dout : input_data;
reg [53:0] edsk[1992]; reg [53:0] edsk[1992];
reg [7:0] spt[166]; reg [7:0] spt[166];
reg [7:0] spt_addr;
always @(posedge clk_sys) begin always @(posedge clk_sys) begin
{edsk_track,edsk_side,edsk_trackf,edsk_sidef,edsk_sector,edsk_sizecode,edsk_offset} <= edsk[edsk_addr]; {edsk_track,edsk_side,edsk_trackf,edsk_sidef,edsk_sector,edsk_sizecode,edsk_offset} <= edsk[edsk_addr];
edsk_spt <= spt[spt_addr]; edsk_spt <= spt[spt_addr];
+5
View File
@@ -99,6 +99,11 @@ generate
assign G = {RGB_fix[7:4],RGB_fix[7:4]}; assign G = {RGB_fix[7:4],RGB_fix[7:4]};
assign B = {RGB_fix[3:0],RGB_fix[3:0]}; assign B = {RGB_fix[3:0],RGB_fix[3:0]};
end end
else if(DW == 18) begin
assign R = {RGB_fix[17:12],RGB_fix[17:16]};
assign G = {RGB_fix[11: 6],RGB_fix[11:10]};
assign B = {RGB_fix[ 5: 0],RGB_fix[ 5: 4]};
end
else begin // 24 else begin // 24
assign R = RGB_fix[23:16]; assign R = RGB_fix[23:16];
assign G = RGB_fix[15:8]; assign G = RGB_fix[15:8];
+159 -40
View File
@@ -103,7 +103,7 @@ USE ieee.numeric_std.ALL;
-- DOWNSCALE : True=Support downscaling False=Downscaling disabled -- DOWNSCALE : True=Support downscaling False=Downscaling disabled
-- BYTESWAP : Little/Big endian byte swap -- BYTESWAP : Little/Big endian byte swap
-- FRAC : Fractional bits, subpixel resolution -- FRAC : Fractional bits, subpixel resolution
-- OHRES : Max. output horizontal resolution. Must be a power of two. -- OHRES : Max. output horizontal resolution. 1024, 2048, 2304, 2560, 4096
-- (Used for sizing line buffers) -- (Used for sizing line buffers)
-- IHRES : Max. input horizontal resolution. Must be a power of two. -- IHRES : Max. input horizontal resolution. Must be a power of two.
-- (Used for sizing line buffers) -- (Used for sizing line buffers)
@@ -125,7 +125,7 @@ ENTITY ascal IS
ADAPTIVE : boolean := true; ADAPTIVE : boolean := true;
DOWNSCALE_NN : boolean := false; DOWNSCALE_NN : boolean := false;
FRAC : natural RANGE 4 TO 8 :=4; FRAC : natural RANGE 4 TO 8 :=4;
OHRES : natural RANGE 1 TO 4096 :=2048; OHRES : natural RANGE 1 TO 4096 :=2304;
IHRES : natural RANGE 1 TO 2048 :=2048; IHRES : natural RANGE 1 TO 2048 :=2048;
N_DW : natural RANGE 64 TO 128 := 128; N_DW : natural RANGE 64 TO 128 := 128;
N_AW : natural RANGE 8 TO 32 := 32; N_AW : natural RANGE 8 TO 32 := 32;
@@ -204,6 +204,7 @@ ENTITY ascal IS
run : IN std_logic :='1'; -- 1=Enable output image. 0=No image run : IN std_logic :='1'; -- 1=Enable output image. 0=No image
freeze : IN std_logic :='0'; -- 1=Disable framebuffer writes freeze : IN std_logic :='0'; -- 1=Disable framebuffer writes
mode : IN unsigned(4 DOWNTO 0); mode : IN unsigned(4 DOWNTO 0);
bob_deint : IN std_logic := '0';
-- SYNC |_________________________/"""""""""\_______| -- SYNC |_________________________/"""""""""\_______|
-- DE |""""""""""""""""""\________________________| -- DE |""""""""""""""""""\________________________|
-- RGB | <#IMAGE#> ^HDISP | -- RGB | <#IMAGE#> ^HDISP |
@@ -222,6 +223,7 @@ ENTITY ascal IS
vmax : IN natural RANGE 0 TO 4095; -- 0 <= vmin < vmax < vdisp vmax : IN natural RANGE 0 TO 4095; -- 0 <= vmin < vmax < vdisp
vrr : IN std_logic := '0'; vrr : IN std_logic := '0';
vrrmax : IN natural RANGE 0 TO 4095 := 0; vrrmax : IN natural RANGE 0 TO 4095 := 0;
swblack : IN std_logic := '0'; -- will output 3 black frame on every resolution switch
-- Scaler format. 00=16bpp 565, 01=24bpp 10=32bpp -- Scaler format. 00=16bpp 565, 01=24bpp 10=32bpp
format : IN unsigned(1 DOWNTO 0) :="01"; format : IN unsigned(1 DOWNTO 0) :="01";
@@ -257,6 +259,9 @@ ENTITY ascal IS
BEGIN BEGIN
ASSERT N_DW=64 OR N_DW=128 REPORT "DW" SEVERITY failure; ASSERT N_DW=64 OR N_DW=128 REPORT "DW" SEVERITY failure;
ASSERT OHRES = 1024 OR OHRES = 2048 OR OHRES = 2304 OR
OHRES = 2560 OR OHRES = 4096 REPORT "OHRES" SEVERITY failure;
END ENTITY ascal; END ENTITY ascal;
--############################################################################## --##############################################################################
@@ -287,6 +292,35 @@ ARCHITECTURE rtl OF ascal IS
END IF; END IF;
END FUNCTION to_std_logic; END FUNCTION to_std_logic;
----------------------------------------------------------
FUNCTION ohres_h(CONSTANT r : natural) RETURN natural IS
BEGIN
CASE r IS
WHEN 1024 => RETURN 1024;
WHEN 2048 => RETURN 2048;
WHEN OTHERS => RETURN 4096;
END CASE;
END FUNCTION;
FUNCTION ohres_l(CONSTANT r : natural) RETURN natural IS
BEGIN
CASE r IS
WHEN 1024 => RETURN 1024;
WHEN 2048 | 2304 | 2560 => RETURN 2048;
WHEN OTHERS => RETURN 4096;
END CASE;
END FUNCTION;
FUNCTION ohres_m(CONSTANT r : natural) RETURN natural IS
BEGIN
CASE r IS
WHEN 1024 | 2048 | 2304 => RETURN 256;
WHEN OTHERS => RETURN 512;
END CASE;
END FUNCTION;
CONSTANT OHRESH : natural := ohres_h(OHRES);
CONSTANT OHRESL : natural := ohres_l(OHRES);
CONSTANT OHRESM : natural := ohres_m(OHRES);
---------------------------------------------------------- ----------------------------------------------------------
CONSTANT NB_BURST : natural :=ilog2(N_BURST); CONSTANT NB_BURST : natural :=ilog2(N_BURST);
CONSTANT NB_LA : natural :=ilog2(N_DW/8); -- Low address bits CONSTANT NB_LA : natural :=ilog2(N_DW/8); -- Low address bits
@@ -318,6 +352,7 @@ ARCHITECTURE rtl OF ascal IS
SIGNAL i_pvs,i_pfl,i_pde,i_pce : std_logic; SIGNAL i_pvs,i_pfl,i_pde,i_pce : std_logic;
SIGNAL i_ppix : type_pix; SIGNAL i_ppix : type_pix;
SIGNAL i_freeze : std_logic; SIGNAL i_freeze : std_logic;
SIGNAL i_bob_deint : std_logic;
SIGNAL i_count : unsigned(2 DOWNTO 0); SIGNAL i_count : unsigned(2 DOWNTO 0);
SIGNAL i_hsize,i_hmin,i_hmax,i_hcpt : uint12; SIGNAL i_hsize,i_hmin,i_hmax,i_hcpt : uint12;
SIGNAL i_hrsize,i_vrsize : uint12; SIGNAL i_hrsize,i_vrsize : uint12;
@@ -333,6 +368,7 @@ ARCHITECTURE rtl OF ascal IS
SIGNAL i_de_delay : natural RANGE 0 TO 31; SIGNAL i_de_delay : natural RANGE 0 TO 31;
SIGNAL i_intercnt : natural RANGE 0 TO 3; SIGNAL i_intercnt : natural RANGE 0 TO 3;
SIGNAL i_inter,i_half,i_flm : std_logic; SIGNAL i_inter,i_half,i_flm : std_logic;
SIGNAL i_wfl : std_logic_vector(2 DOWNTO 0);
SIGNAL i_write,i_wreq,i_alt,i_line,i_wline,i_wline_mem : std_logic; SIGNAL i_write,i_wreq,i_alt,i_line,i_wline,i_wline_mem : std_logic;
SIGNAL i_walt,i_walt_mem,i_wreq_mem : std_logic; SIGNAL i_walt,i_walt_mem,i_wreq_mem : std_logic;
SIGNAL i_wdelay : natural RANGE 0 TO 7; SIGNAL i_wdelay : natural RANGE 0 TO 7;
@@ -362,7 +398,7 @@ ARCHITECTURE rtl OF ascal IS
SIGNAL i_hacc,i_vacc : uint13; SIGNAL i_hacc,i_vacc : uint13;
SIGNAL i_hdown,i_vdown : std_logic; SIGNAL i_hdown,i_vdown : std_logic;
SIGNAL i_divcpt : natural RANGE 0 TO 36; SIGNAL i_divcpt : natural RANGE 0 TO 36;
SIGNAL i_lwad,i_lrad : natural RANGE 0 TO OHRES-1; SIGNAL i_lwad,i_lrad : natural RANGE 0 TO OHRESH-1;
SIGNAL i_lwr,i_bil : std_logic; SIGNAL i_lwr,i_bil : std_logic;
SIGNAL i_ldw,i_ldrm : type_pix; SIGNAL i_ldw,i_ldrm : type_pix;
SIGNAL i_hpixp,i_hpix0,i_hpix1,i_hpix2,i_hpix3,i_hpix4 : type_pix; SIGNAL i_hpixp,i_hpix0,i_hpix1,i_hpix2,i_hpix3,i_hpix4 : type_pix;
@@ -410,6 +446,8 @@ ARCHITECTURE rtl OF ascal IS
-- Output -- Output
SIGNAL o_run : std_logic; SIGNAL o_run : std_logic;
SIGNAL o_freeze : std_logic; SIGNAL o_freeze : std_logic;
SIGNAL o_bob_deint : std_logic;
SIGNAL o_iwfl : std_logic_vector(2 DOWNTO 0);
SIGNAL o_mode,o_hmode,o_vmode : unsigned(4 DOWNTO 0); SIGNAL o_mode,o_hmode,o_vmode : unsigned(4 DOWNTO 0);
SIGNAL o_format : unsigned(5 DOWNTO 0); SIGNAL o_format : unsigned(5 DOWNTO 0);
SIGNAL o_fb_pal_dr : unsigned(23 DOWNTO 0); SIGNAL o_fb_pal_dr : unsigned(23 DOWNTO 0);
@@ -456,13 +494,21 @@ ARCHITECTURE rtl OF ascal IS
SIGNAL o_reset_na : std_logic; SIGNAL o_reset_na : std_logic;
SIGNAL o_dpram : arr_dw(0 TO BLEN*2-1); SIGNAL o_dpram : arr_dw(0 TO BLEN*2-1);
ATTRIBUTE ramstyle OF o_dpram : SIGNAL IS "no_rw_check"; ATTRIBUTE ramstyle OF o_dpram : SIGNAL IS "no_rw_check";
SIGNAL o_line0,o_line1,o_line2,o_line3 : arr_pix(0 TO OHRES-1); SIGNAL o_line0,o_line1,o_line2,o_line3 : arr_pix(0 TO OHRESL-1);
SIGNAL o_linf0,o_linf1,o_linf2,o_linf3 : arr_pix(0 TO OHRESM-1);
ATTRIBUTE ramstyle OF o_line0 : SIGNAL IS "no_rw_check"; ATTRIBUTE ramstyle OF o_line0 : SIGNAL IS "no_rw_check";
ATTRIBUTE ramstyle OF o_line1 : SIGNAL IS "no_rw_check"; ATTRIBUTE ramstyle OF o_line1 : SIGNAL IS "no_rw_check";
ATTRIBUTE ramstyle OF o_line2 : SIGNAL IS "no_rw_check"; ATTRIBUTE ramstyle OF o_line2 : SIGNAL IS "no_rw_check";
ATTRIBUTE ramstyle OF o_line3 : SIGNAL IS "no_rw_check"; ATTRIBUTE ramstyle OF o_line3 : SIGNAL IS "no_rw_check";
SIGNAL o_wadl,o_radl0,o_radl1,o_radl2,o_radl3 : natural RANGE 0 TO OHRES-1; ATTRIBUTE ramstyle OF o_linf0 : SIGNAL IS "no_rw_check";
SIGNAL o_ldw,o_ldr0,o_ldr1,o_ldr2,o_ldr3 : type_pix; ATTRIBUTE ramstyle OF o_linf1 : SIGNAL IS "no_rw_check";
ATTRIBUTE ramstyle OF o_linf2 : SIGNAL IS "no_rw_check";
ATTRIBUTE ramstyle OF o_linf3 : SIGNAL IS "no_rw_check";
SIGNAL o_wadl,o_radl0,o_radl1,o_radl2,o_radl3 : natural RANGE 0 TO OHRESH-1;
SIGNAL o_ldr0,o_ldr1,o_ldr2,o_ldr3,o_ldw : type_pix;
SIGNAL o_ler0,o_ler1,o_ler2,o_ler3 : type_pix;
SIGNAL o_lex0,o_lex1,o_lex2,o_lex3 : std_logic;
SIGNAL o_wr : unsigned(3 DOWNTO 0); SIGNAL o_wr : unsigned(3 DOWNTO 0);
SIGNAL o_hcpt,o_vcpt,o_vcpt_pre,o_vcpt_pre2,o_vcpt_pre3,o_vcpt2 : uint12; SIGNAL o_hcpt,o_vcpt,o_vcpt_pre,o_vcpt_pre2,o_vcpt_pre3,o_vcpt2 : uint12;
SIGNAL o_ihsize,o_ihsizem,o_ivsize : uint12; SIGNAL o_ihsize,o_ihsizem,o_ivsize : uint12;
@@ -472,7 +518,7 @@ ARCHITECTURE rtl OF ascal IS
SIGNAL o_hfrac : arr_frac(0 TO 9); SIGNAL o_hfrac : arr_frac(0 TO 9);
ATTRIBUTE ramstyle OF o_hfrac : SIGNAL IS "logic"; -- avoid blockram shift register ATTRIBUTE ramstyle OF o_hfrac : SIGNAL IS "logic"; -- avoid blockram shift register
SIGNAL o_hacc,o_hacc_ini,o_hacc_next,o_vacc,o_vacc_next,o_vacc_ini : natural RANGE 0 TO 4*OHRES-1; SIGNAL o_hacc,o_hacc_ini,o_hacc_next,o_vacc,o_vacc_next,o_vacc_ini : natural RANGE 0 TO 4*OHRESH-1;
SIGNAL o_hsv,o_vsv,o_dev,o_pev,o_end : unsigned(0 TO 11); SIGNAL o_hsv,o_vsv,o_dev,o_pev,o_end : unsigned(0 TO 11);
SIGNAL o_hsp,o_vss : std_logic; SIGNAL o_hsp,o_vss : std_logic;
SIGNAL o_vcarrym,o_prim : boolean; SIGNAL o_vcarrym,o_prim : boolean;
@@ -490,8 +536,9 @@ ARCHITECTURE rtl OF ascal IS
TYPE arr_uint4 IS ARRAY (natural RANGE <>) OF natural RANGE 0 TO 15; TYPE arr_uint4 IS ARRAY (natural RANGE <>) OF natural RANGE 0 TO 15;
SIGNAL o_off : arr_uint4(0 TO 2); SIGNAL o_off : arr_uint4(0 TO 2);
SIGNAL o_bibu : std_logic :='0'; SIGNAL o_bibu : std_logic :='0';
SIGNAL o_dcptv : arr_uint12(1 TO 14); SIGNAL o_dcptv : arr_uint12(13 TO 14);
SIGNAL o_dcpt : uint12; SIGNAL o_dcpt_clr, o_dcpt_inc : std_logic;
SIGNAL o_dcptv_clr, o_dcptv_inc : std_logic_vector(1 TO 12);
SIGNAL o_hpixs,o_hpix0,o_hpix1,o_hpix2,o_hpix3 : type_pix; SIGNAL o_hpixs,o_hpix0,o_hpix1,o_hpix2,o_hpix3 : type_pix;
SIGNAL o_hpixq : arr_pixq(2 TO 8); SIGNAL o_hpixq : arr_pixq(2 TO 8);
ATTRIBUTE ramstyle OF o_hpixq : SIGNAL IS "logic"; -- avoid blockram shift register ATTRIBUTE ramstyle OF o_hpixq : SIGNAL IS "logic"; -- avoid blockram shift register
@@ -499,7 +546,6 @@ ARCHITECTURE rtl OF ascal IS
SIGNAL o_vpix_outer : arr_pix(0 TO 2); SIGNAL o_vpix_outer : arr_pix(0 TO 2);
SIGNAL o_vpix_inner : arr_pix(0 TO 6); SIGNAL o_vpix_inner : arr_pix(0 TO 6);
SIGNAL o_vpe : std_logic; SIGNAL o_vpe : std_logic;
SIGNAL o_div : arr_div(0 TO 2); --uint12; SIGNAL o_div : arr_div(0 TO 2); --uint12;
SIGNAL o_dir : arr_frac(0 TO 2); SIGNAL o_dir : arr_frac(0 TO 2);
@@ -510,6 +556,7 @@ ARCHITECTURE rtl OF ascal IS
SIGNAL o_divrun : std_logic; SIGNAL o_divrun : std_logic;
SIGNAL o_hacpt,o_vacpt : unsigned(11 DOWNTO 0); SIGNAL o_hacpt,o_vacpt : unsigned(11 DOWNTO 0);
SIGNAL o_vacptl : unsigned(1 DOWNTO 0); SIGNAL o_vacptl : unsigned(1 DOWNTO 0);
signal o_newres : integer range 0 to 3;
----------------------------------------------------------------------------- -----------------------------------------------------------------------------
FUNCTION shift_ishift(shift : unsigned(0 TO 119); FUNCTION shift_ishift(shift : unsigned(0 TO 119);
@@ -1130,6 +1177,7 @@ BEGIN
i_pushhead<='0'; i_pushhead<='0';
i_eol<='0'; -- End Of Line i_eol<='0'; -- End Of Line
i_freeze <=freeze; -- <ASYNC> i_freeze <=freeze; -- <ASYNC>
i_bob_deint <= bob_deint;
i_iauto<=iauto; -- <ASYNC> i_iauto<=iauto; -- <ASYNC>
i_wreq<='0'; i_wreq<='0';
i_wr<='0'; i_wr<='0';
@@ -1190,11 +1238,13 @@ BEGIN
i_vcpt<=0; i_vcpt<=0;
IF i_inter='1' AND i_flm='0' AND i_half='0' AND INTER THEN IF i_inter='1' AND i_flm='0' AND i_half='0' AND INTER THEN
i_line<='1'; i_line<='1';
i_wfl(o_ibuf1) <= '0';
i_adrsi<=to_unsigned(N_BURST * i_hburst,32) + i_adrsi<=to_unsigned(N_BURST * i_hburst,32) +
to_unsigned(N_BURST * to_integer( to_unsigned(N_BURST * to_integer(
unsigned'("00") & to_std_logic(HEADER)),32); unsigned'("00") & to_std_logic(HEADER)),32);
ELSE ELSE
i_line<='0'; i_line<='0';
i_wfl(o_ibuf0) <= '1';
i_adrsi<=to_unsigned(N_BURST * to_integer( i_adrsi<=to_unsigned(N_BURST * to_integer(
unsigned'("00") & to_std_logic(HEADER)),32); unsigned'("00") & to_std_logic(HEADER)),32);
END IF; END IF;
@@ -1204,8 +1254,8 @@ BEGIN
i_vcpt>=i_vmin AND i_vcpt<=i_vmax); i_vcpt>=i_vmin AND i_vcpt<=i_vmax);
-- Detects end of frame for triple buffering. -- Detects end of frame for triple buffering.
i_endframe0<=i_vs AND (NOT i_inter OR i_flm); i_endframe0<=i_vs AND (NOT i_inter OR i_flm OR i_bob_deint);
i_endframe1<=i_vs AND (NOT i_inter OR NOT i_flm); i_endframe1<=i_vs AND (NOT i_inter OR NOT i_flm OR i_bob_deint);
i_vss<=to_std_logic(i_vcpt>=i_vmin AND i_vcpt<=i_vmax); i_vss<=to_std_logic(i_vcpt>=i_vmin AND i_vcpt<=i_vmax);
@@ -1453,12 +1503,12 @@ BEGIN
-- Push pixels to downscaling line buffer -- Push pixels to downscaling line buffer
i_lwr<=i_hnp4 AND i_ven5 AND i_pce; i_lwr<=i_hnp4 AND i_ven5 AND i_pce;
IF i_lwr='1' THEN IF i_lwr='1' THEN
i_lwad<=(i_lwad+1) MOD OHRES; i_lwad<=(i_lwad+1) MOD OHRESH;
END IF; END IF;
i_ldw<=i_hpix; i_ldw<=i_hpix;
IF i_hnp3='1' AND i_ven4='1' AND i_pce='1' THEN IF i_hnp3='1' AND i_ven4='1' AND i_pce='1' THEN
i_lrad<=(i_lrad+1) MOD OHRES; i_lrad<=(i_lrad+1) MOD OHRESH;
END IF; END IF;
------------------------------------------------------ ------------------------------------------------------
@@ -1817,7 +1867,7 @@ BEGIN
VARIABLE shift_v : unsigned(0 TO N_DW+15); VARIABLE shift_v : unsigned(0 TO N_DW+15);
VARIABLE hpix_v : type_pix; VARIABLE hpix_v : type_pix;
VARIABLE hcarry_v,vcarry_v : boolean; VARIABLE hcarry_v,vcarry_v : boolean;
VARIABLE dif_v : natural RANGE 0 TO 8*OHRES-1; VARIABLE dif_v : natural RANGE 0 TO 8*OHRESH-1;
VARIABLE off_v : natural RANGE 0 TO 15; VARIABLE off_v : natural RANGE 0 TO 15;
BEGIN BEGIN
IF o_reset_na='0' THEN IF o_reset_na='0' THEN
@@ -1862,6 +1912,8 @@ BEGIN
o_isync <= '0'; o_isync <= '0';
o_isync2 <= o_isync; o_isync2 <= o_isync;
o_freeze <= freeze; o_freeze <= freeze;
o_bob_deint <= bob_deint;
o_iwfl <= i_wfl;
o_inter <=i_inter; -- <ASYNC> o_inter <=i_inter; -- <ASYNC>
o_iendframe0<=i_endframe0; -- <ASYNC> o_iendframe0<=i_endframe0; -- <ASYNC>
o_iendframe02<=o_iendframe0; o_iendframe02<=o_iendframe0;
@@ -1890,6 +1942,14 @@ BEGIN
o_ivsize<=i_vrsize; -- <ASYNC> o_ivsize<=i_vrsize; -- <ASYNC>
o_hdown<=i_hdown; -- <ASYNC> o_hdown<=i_hdown; -- <ASYNC>
o_vdown<=i_vdown; -- <ASYNC> o_vdown<=i_vdown; -- <ASYNC>
IF (o_newres > 0) then
o_newres <= o_newres- 1;
END IF;
END IF;
IF (swblack = '1' and o_fb_ena = '0' and (o_ihsize /= i_hrsize or o_ivsize /= i_vrsize)) then
o_newres <= 3;
END IF; END IF;
-- Simultaneous change of input and output framebuffers -- Simultaneous change of input and output framebuffers
@@ -2086,7 +2146,26 @@ BEGIN
o_read<=o_read_pre AND o_run; o_read<=o_read_pre AND o_run;
o_rline<=o_vacpt(0); -- Even/Odd line for interlaced video o_rline<=o_vacpt(0); -- Even/Odd line for interlaced video
----
-- When bob deinterlacing we read lines from one buffer (the most current) but we read them twice
-- (in contrast to weave deinterlacing where we read each 480p line from alternating buffers)
-- To counteract the severe vibrating/motion with bob deinterlacing, we need to offset one field
-- by a half-line. This is done by only reading the first line of the 'even' frame once
IF o_inter='1' AND o_bob_deint='1' THEN
IF o_iwfl(o_obuf0)='0' THEN
IF o_vacpt=0 OR o_rline='1' THEN
o_adrs_pre <= to_integer(o_vacpt) * to_integer(o_stride); o_adrs_pre <= to_integer(o_vacpt) * to_integer(o_stride);
ELSE
o_adrs_pre <= (to_integer(o_vacpt)-1) * to_integer(o_stride);
END IF;
ELSE
o_adrs_pre <= to_integer(o_vacpt(11 DOWNTO 1) & "0") * to_integer(o_stride);
END IF;
ELSE
o_adrs_pre<=to_integer(o_vacpt) * to_integer(o_stride);
END IF;
IF o_adrsa='1' THEN IF o_adrsa='1' THEN
IF o_fload=2 THEN IF o_fload=2 THEN
o_adrs<=to_unsigned(o_hbcpt * N_BURST,32); o_adrs<=to_unsigned(o_hbcpt * N_BURST,32);
@@ -2103,6 +2182,9 @@ BEGIN
------------------------------------------------------ ------------------------------------------------------
-- Copy from buffered memory to pixel lines -- Copy from buffered memory to pixel lines
o_sh<='0'; o_sh<='0';
o_dcpt_clr <= '0';
o_dcpt_inc <= '0';
CASE o_copy IS CASE o_copy IS
WHEN sWAIT => WHEN sWAIT =>
o_copyv(0)<='0'; o_copyv(0)<='0';
@@ -2121,7 +2203,7 @@ BEGIN
o_hacc <=o_hacc_ini; o_hacc <=o_hacc_ini;
o_hacc_next<=o_hacc_ini + 2*o_ihsize; o_hacc_next<=o_hacc_ini + 2*o_ihsize;
o_hacpt <=x"000"; o_hacpt <=x"000";
o_dcpt<=0; o_dcpt_clr <= '1';
o_dshi<=2; o_dshi<=2;
o_acpt<=0; o_acpt<=0;
o_first<='1'; o_first<='1';
@@ -2149,17 +2231,17 @@ BEGIN
WHEN sCOPY => WHEN sCOPY =>
-- dshi : Force shift first two or three pixels of each line -- dshi : Force shift first two or three pixels of each line
IF o_dshi=0 THEN IF o_dshi=0 THEN
dif_v:=(o_hacc_next - 2*o_hsize + (8*OHRES)) MOD (8*OHRES); dif_v:=(o_hacc_next - 2*o_hsize + (8*OHRESH)) MOD (8*OHRESH);
IF dif_v>=4*OHRES THEN IF dif_v>=4*OHRESH THEN
o_hacc<=o_hacc_next; o_hacc<=o_hacc_next;
o_hacc_next<=o_hacc_next + 2*o_ihsize; o_hacc_next<=o_hacc_next + 2*o_ihsize;
hcarry_v:=false; hcarry_v:=false;
ELSE ELSE
o_hacc<=dif_v; o_hacc<=dif_v;
o_hacc_next<=(dif_v + 2*o_ihsize + (4*OHRES)) MOD (4*OHRES); o_hacc_next<=(dif_v + 2*o_ihsize + (4*OHRESH)) MOD (4*OHRESH);
hcarry_v:=true; hcarry_v:=true;
END IF; END IF;
o_dcpt<=(o_dcpt+1) MOD 4096; o_dcpt_inc <= '1';
ELSE ELSE
o_dshi<=o_dshi-1; o_dshi<=o_dshi-1;
hcarry_v:=false; hcarry_v:=false;
@@ -2219,6 +2301,9 @@ BEGIN
hpix_v:=(r=>o_fb_pal_dr(23 DOWNTO 16),g=>o_fb_pal_dr(15 DOWNTO 8), hpix_v:=(r=>o_fb_pal_dr(23 DOWNTO 16),g=>o_fb_pal_dr(15 DOWNTO 8),
b=>o_fb_pal_dr(7 DOWNTO 0)); b=>o_fb_pal_dr(7 DOWNTO 0));
END IF; END IF;
IF (o_newres > 0) then
hpix_v := (others => (others => '0'));
END IF;
o_hpix0<=hpix_v; o_hpix0<=hpix_v;
o_hpix1<=o_hpix0; o_hpix1<=o_hpix0;
o_hpix2<=o_hpix1; o_hpix2<=o_hpix1;
@@ -2526,13 +2611,19 @@ BEGIN
o_hfrac(2 TO 9) <= o_hfrac(1 TO 8); o_hfrac(2 TO 9) <= o_hfrac(1 TO 8);
o_copyv(1 TO 14)<=o_copyv(0 TO 13); o_copyv(1 TO 14)<=o_copyv(0 TO 13);
o_dcptv_clr(1 TO 12)<=o_dcpt_clr & o_dcptv_clr(1 TO 11);
o_dcptv_inc(1 TO 12)<=o_dcpt_inc & o_dcptv_inc(1 TO 11);
o_dcptv(1)<=o_dcpt; IF o_dcptv_clr(12)='1' THEN
IF o_dcptv(1)>=o_hsize THEN o_dcptv(13) <= 0;
o_copyv(2)<='0'; ELSIF o_dcptv_inc(12)='1' THEN
o_dcptv(13) <= (o_dcptv(13) + 1) MOD OHRESH;
END IF;
o_dcptv(14)<=o_dcptv(13);
IF o_dcptv(13)>=o_hsize THEN
o_copyv(14)<='0';
END IF; END IF;
o_dcptv(2)<=o_dcptv(1) MOD OHRES;
o_dcptv(3 TO 14)<=o_dcptv(2 TO 13);
-- C2 -- C2
o_hpixq(2)<=(o_hpix3,o_hpix2,o_hpix1,o_hpix0); o_hpixq(2)<=(o_hpix3,o_hpix2,o_hpix1,o_hpix0);
@@ -2625,17 +2716,39 @@ BEGIN
OLBUF:PROCESS(o_clk) IS OLBUF:PROCESS(o_clk) IS
BEGIN BEGIN
IF rising_edge(o_clk) THEN IF rising_edge(o_clk) THEN
-----------------------------------------------
-- WRITES -- WRITES
IF o_wr(0)='1' THEN o_line0(o_wadl)<=o_ldw; END IF; IF o_wr(0)='1' AND o_wadl < OHRESL THEN o_line0(o_wadl MOD OHRESL)<=o_ldw; END IF;
IF o_wr(1)='1' THEN o_line1(o_wadl)<=o_ldw; END IF; IF o_wr(1)='1' AND o_wadl < OHRESL THEN o_line1(o_wadl MOD OHRESL)<=o_ldw; END IF;
IF o_wr(2)='1' THEN o_line2(o_wadl)<=o_ldw; END IF; IF o_wr(2)='1' AND o_wadl < OHRESL THEN o_line2(o_wadl MOD OHRESL)<=o_ldw; END IF;
IF o_wr(3)='1' THEN o_line3(o_wadl)<=o_ldw; END IF; IF o_wr(3)='1' AND o_wadl < OHRESL THEN o_line3(o_wadl MOD OHRESL)<=o_ldw; END IF;
IF OHRES = 2304 OR OHRES = 2560 THEN
IF o_wr(0)='1' AND o_wadl >= OHRESL THEN o_linf0(o_wadl MOD OHRESM)<=o_ldw; END IF;
IF o_wr(1)='1' AND o_wadl >= OHRESL THEN o_linf1(o_wadl MOD OHRESM)<=o_ldw; END IF;
IF o_wr(2)='1' AND o_wadl >= OHRESL THEN o_linf2(o_wadl MOD OHRESM)<=o_ldw; END IF;
IF o_wr(3)='1' AND o_wadl >= OHRESL THEN o_linf3(o_wadl MOD OHRESM)<=o_ldw; END IF;
END IF;
-----------------------------------------------
-- READS -- READS
o_ldr0<=o_line0(o_radl0); o_ldr0<=o_line0(o_radl0 MOD OHRESL);
o_ldr1<=o_line1(o_radl1); o_ldr1<=o_line1(o_radl1 MOD OHRESL);
o_ldr2<=o_line2(o_radl2); o_ldr2<=o_line2(o_radl2 MOD OHRESL);
o_ldr3<=o_line3(o_radl3); o_ldr3<=o_line3(o_radl3 MOD OHRESL);
IF OHRES = 2304 OR OHRES = 2560 THEN
o_ler0<=o_linf0(o_radl0 MOD OHRESM);
o_ler1<=o_linf1(o_radl1 MOD OHRESM);
o_ler2<=o_linf2(o_radl2 MOD OHRESM);
o_ler3<=o_linf3(o_radl3 MOD OHRESM);
END IF;
o_lex0 <= to_std_logic(o_radl0 >= OHRESL);
o_lex1 <= to_std_logic(o_radl1 >= OHRESL);
o_lex2 <= to_std_logic(o_radl2 >= OHRESL);
o_lex3 <= to_std_logic(o_radl3 >= OHRESL);
-----------------------------------------------
END IF; END IF;
END PROCESS OLBUF; END PROCESS OLBUF;
@@ -2721,16 +2834,17 @@ BEGIN
VSCAL:PROCESS(o_clk) IS VSCAL:PROCESS(o_clk) IS
VARIABLE pixq_v : arr_pix(0 TO 3); VARIABLE pixq_v : arr_pix(0 TO 3);
VARIABLE vlumpix_v : type_pix; VARIABLE vlumpix_v : type_pix;
VARIABLE r1_v, r2_v : natural RANGE 0 TO OHRES-1; VARIABLE r1_v, r2_v : natural RANGE 0 TO OHRESH-1;
VARIABLE fracnn_v : std_logic; VARIABLE fracnn_v : std_logic;
VARIABLE o_l0_v, o_l1_v, o_l2_v, o_l3_v : type_pix;
BEGIN BEGIN
IF rising_edge(o_clk) THEN IF rising_edge(o_clk) THEN
IF o_ce='1' THEN IF o_ce='1' THEN
o_v_hmin_adj<=o_hmin + 5; o_v_hmin_adj<=o_hmin + 5;
fracnn_v := o_vfrac(o_vfrac'left); fracnn_v := o_vfrac(o_vfrac'left);
r1_v := (o_hcpt - o_v_hmin_adj + OHRES) MOD OHRES; r1_v := (o_hcpt - o_v_hmin_adj + OHRESH) MOD OHRESH;
r2_v := (o_hcpt - o_hmin + OHRES) MOD OHRES; r2_v := (o_hcpt - o_hmin + OHRESH) MOD OHRESH;
-- CYCLE 1 ----------------------------------------- -- CYCLE 1 -----------------------------------------
-- Read mem -- Read mem
@@ -2757,11 +2871,16 @@ BEGIN
-- CYCLE 2 ----------------------------------------- -- CYCLE 2 -----------------------------------------
-- Lines reordering -- Lines reordering
IF o_lex0='0' THEN o_l0_v := o_ldr0; ELSE o_l0_v := o_ler0; END IF;
IF o_lex1='0' THEN o_l1_v := o_ldr1; ELSE o_l1_v := o_ler1; END IF;
IF o_lex2='0' THEN o_l2_v := o_ldr2; ELSE o_l2_v := o_ler2; END IF;
IF o_lex3='0' THEN o_l3_v := o_ldr3; ELSE o_l3_v := o_ler3; END IF;
CASE o_vacptl IS CASE o_vacptl IS
WHEN "10" => pixq_v:=(o_ldr0,o_ldr1,o_ldr2,o_ldr3); WHEN "10" => pixq_v:=(o_l0_v,o_l1_v,o_l2_v,o_l3_v);
WHEN "11" => pixq_v:=(o_ldr1,o_ldr2,o_ldr3,o_ldr0); WHEN "11" => pixq_v:=(o_l1_v,o_l2_v,o_l3_v,o_l0_v);
WHEN "00" => pixq_v:=(o_ldr2,o_ldr3,o_ldr0,o_ldr1); WHEN "00" => pixq_v:=(o_l2_v,o_l3_v,o_l0_v,o_l1_v);
WHEN OTHERS => pixq_v:=(o_ldr3,o_ldr0,o_ldr1,o_ldr2); WHEN OTHERS => pixq_v:=(o_l3_v,o_l0_v,o_l1_v,o_l2_v);
END CASE; END CASE;
IF fracnn_v = '0' THEN IF fracnn_v = '0' THEN
+26 -1
View File
@@ -2,13 +2,16 @@
# Build TimeStamp Verilog Module # Build TimeStamp Verilog Module
# Jeff Wiencrot - 8/1/2011 # Jeff Wiencrot - 8/1/2011
# Sorgelig - 02/11/2019 # Sorgelig - 02/11/2019
# Stan Hodge - 04/22/2024
proc generateBuildID_Verilog {} { proc generateBuildID_Verilog {} {
# Get the timestamp (see: http://www.altera.com/support/examples/tcl/tcl-date-time-stamp.html) # Get the timestamp (see: http://www.altera.com/support/examples/tcl/tcl-date-time-stamp.html)
set buildDate "`define BUILD_DATE \"[clock format [ clock seconds ] -format %y%m%d]\"" set buildDate "`define BUILD_DATE \"[clock format [ clock seconds ] -format %y%m%d]\""
# Create a Verilog file for output # Create a Verilog file(s) for output
set outputFileName "build_id.v" set outputFileName "build_id.v"
set outputFileNameNum "build_id_num.v"
set fileData "" set fileData ""
if { [file exists $outputFileName]} { if { [file exists $outputFileName]} {
@@ -17,13 +20,35 @@ proc generateBuildID_Verilog {} {
close $outputFile close $outputFile
} }
set fileData_num ""
if { [file exists $outputFileNameNum]} {
set outputFile [open $outputFileNameNum "r"]
set fileData_num [read $outputFile]
close $outputFile
}
if {$buildDate ne $fileData} { if {$buildDate ne $fileData} {
set outputFile [open $outputFileName "w"] set outputFile [open $outputFileName "w"]
puts -nonewline $outputFile $buildDate puts -nonewline $outputFile $buildDate
close $outputFile close $outputFile
set buildnumbervar 1
# Send confirmation message to the Messages window # Send confirmation message to the Messages window
post_message "Generated: [pwd]/$outputFileName: $buildDate" post_message "Generated: [pwd]/$outputFileName: $buildDate"
} else {
scan $fileData_num "`define BUILD_NUMBER \"%d" buildnumbervar
incr buildnumbervar
} }
set buildnumber "`define BUILD_NUMBER \"[format "%03d" $buildnumbervar]\""
set outputFile [open $outputFileNameNum "w"]
puts -nonewline $outputFile $buildnumber
close $outputFile
post_message "Generated: [pwd]/$outputFileNameNum: $buildnumber"
} }
# Build CDF file # Build CDF file
+11 -5
View File
@@ -27,7 +27,7 @@
// VDNUM 1..10 // VDNUM 1..10
// BLKSZ 0..7: 0 = 128, 1 = 256, 2 = 512(default), .. 7 = 16384 // BLKSZ 0..7: 0 = 128, 1 = 256, 2 = 512(default), .. 7 = 16384
// //
module hps_io #(parameter CONF_STR, CONF_STR_BRAM=1, PS2DIV=0, WIDE=0, VDNUM=1, BLKSZ=2, PS2WE=0) module hps_io #(parameter CONF_STR, CONF_STR_BRAM=0, PS2DIV=0, WIDE=0, VDNUM=1, BLKSZ=2, PS2WE=0, STRLEN=$size(CONF_STR)>>3)
( (
input clk_sys, input clk_sys,
inout [48:0] HPS_BUS, inout [48:0] HPS_BUS,
@@ -232,8 +232,7 @@ video_calc video_calc
///////////////////////////////////////////////////////// /////////////////////////////////////////////////////////
localparam STRLEN = $size(CONF_STR)>>3; localparam MAX_W = $clog2((64 > (STRLEN+2)) ? 64 : (STRLEN+2))-1;
localparam MAX_W = $clog2((32 > (STRLEN+2)) ? 32 : (STRLEN+2))-1;
wire [7:0] conf_byte; wire [7:0] conf_byte;
generate generate
@@ -1032,8 +1031,15 @@ module confstr_rom #(parameter CONF_STR, STRLEN)
output reg [7:0] conf_byte output reg [7:0] conf_byte
); );
wire [7:0] rom[STRLEN]; reg [7:0] rom[STRLEN];
initial for(int i = 0; i < STRLEN; i++) rom[i] = CONF_STR[((STRLEN-i)*8)-1 -:8];
initial begin
if( CONF_STR=="" )
$readmemh("cfgstr.hex",rom);
else
for(int i = 0; i < STRLEN; i++) rom[i] = CONF_STR[((STRLEN-i)*8)-1 -:8];
end
always @ (posedge clk_sys) conf_byte <= rom[conf_addr]; always @ (posedge clk_sys) conf_byte <= rom[conf_addr];
endmodule endmodule
+1 -1
View File
@@ -75,7 +75,7 @@ always @(posedge CLK) begin
END <= 0; END <= 0;
rd <= READ; rd <= READ;
len <= I2C_WLEN; len <= I2C_WLEN;
if(READ) SD <= {2'b10, I2C_ADDR, 1'b1, 1'b1, 8'b11111111, 1'b0, 3'b011, 9'b111111111}; if(READ) SD <= {2'b10, I2C_ADDR, 1'b1, 1'b1, 8'b11111111, 1'b1, 3'b011, 9'b111111111};
else SD <= {2'b10, I2C_ADDR, 1'b0, 1'b1, I2C_WDATA1, 1'b1, I2C_WDATA2, 4'b1011}; else SD <= {2'b10, I2C_ADDR, 1'b0, 1'b1, I2C_WDATA1, 1'b1, I2C_WDATA2, 4'b1011};
SD_COUNTER <= 0; SD_COUNTER <= 0;
end else begin end else begin
+10 -3
View File
@@ -8,7 +8,9 @@ module mcp23009
output reg [2:0] btn, output reg [2:0] btn,
input [2:0] led, input [2:0] led,
output reg sd_cd, output reg flg_sd_cd,
output reg flg_present,
output reg flg_mode,
output scl, output scl,
inout sda inout sda
@@ -50,7 +52,9 @@ always@(posedge clk) begin
idx <= 0; idx <= 0;
btn <= 0; btn <= 0;
rw <= 0; rw <= 0;
sd_cd <= 1; flg_sd_cd <= 1;
flg_present <= 0;
flg_mode <= 1;
end end
else begin else begin
if(~&init_data[idx]) begin if(~&init_data[idx]) begin
@@ -84,7 +88,10 @@ always@(posedge clk) begin
state <= 0; state <= 0;
rw <= 0; rw <= 0;
if(!error) begin if(!error) begin
if(rw) {sd_cd, btn} <= {dout[7], dout[5:3]}; if(rw) begin
{flg_sd_cd, flg_mode, btn} <= {dout[7:3]};
flg_present <= 1;
end
rw <= ~rw; rw <= ~rw;
end end
end end
+2 -41
View File
@@ -1,44 +1,5 @@
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_TOOL_NAME "altera_pll_reconfig"
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_TOOL_VERSION "17.0"
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_TOOL_ENV "mwpim"
set_global_assignment -library "pll_cfg" -name MISC_FILE [file join $::quartus(qip_path) "pll_cfg.cmp"]
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_TARGETED_DEVICE_FAMILY "Cyclone V"
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_GENERATED_DEVICE_FAMILY "{Cyclone V}"
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_QSYS_MODE "UNKNOWN"
set_global_assignment -name SYNTHESIS_ONLY_QIP ON set_global_assignment -name SYNTHESIS_ONLY_QIP ON
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_COMPONENT_NAME "cGxsX2hkbWlfY2Zn" set_global_assignment -library "pll_cfg" -name VERILOG_FILE [file join $::quartus(qip_path) "pll_cfg/pll_cfg.v"]
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_COMPONENT_DISPLAY_NAME "QWx0ZXJhIFBMTCBSZWNvbmZpZw==" set_global_assignment -library "pll_cfg" -name VERILOG_FILE [file join $::quartus(qip_path) "pll_cfg/pll_cfg_hdmi.v"]
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_COMPONENT_REPORT_HIERARCHY "Off"
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_COMPONENT_INTERNAL "Off"
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_COMPONENT_AUTHOR "QWx0ZXJhIENvcnBvcmF0aW9u"
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_COMPONENT_VERSION "MTcuMA=="
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_COMPONENT_DESCRIPTION "QWx0ZXJhIFBoYXNlLUxvY2tlZCBMb29wIFJlY29uZmlndXJhdGlvbiBCbG9jayhBTFRFUkFfUExMX1JFQ09ORklHKQ=="
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_COMPONENT_PARAMETER "RU5BQkxFX0JZVEVFTkFCTEU=::ZmFsc2U=::QWRkIGJ5dGVlbmFibGUgcG9ydA=="
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_COMPONENT_PARAMETER "QllURUVOQUJMRV9XSURUSA==::NA==::QllURUVOQUJMRV9XSURUSA=="
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_COMPONENT_PARAMETER "UkVDT05GSUdfQUREUl9XSURUSA==::Ng==::UkVDT05GSUdfQUREUl9XSURUSA=="
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_COMPONENT_PARAMETER "UkVDT05GSUdfREFUQV9XSURUSA==::MzI=::UkVDT05GSUdfREFUQV9XSURUSA=="
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_COMPONENT_PARAMETER "cmVjb25mX3dpZHRo::NjQ=::cmVjb25mX3dpZHRo"
set_global_assignment -entity "pll_cfg" -library "pll_cfg" -name IP_COMPONENT_PARAMETER "V0FJVF9GT1JfTE9DSw==::dHJ1ZQ==::V0FJVF9GT1JfTE9DSw=="
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_NAME "YWx0ZXJhX3BsbF9yZWNvbmZpZ190b3A="
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_DISPLAY_NAME "QWx0ZXJhIFBMTCBSZWNvbmZpZw=="
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_REPORT_HIERARCHY "Off"
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_INTERNAL "Off"
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_AUTHOR "QWx0ZXJhIENvcnBvcmF0aW9u"
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_VERSION "MTcuMA=="
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_DESCRIPTION "QWx0ZXJhIFBoYXNlLUxvY2tlZCBMb29wIFJlY29uZmlndXJhdGlvbiBCbG9jayhBTFRFUkFfUExMX1JFQ09ORklHKQ=="
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_PARAMETER "ZGV2aWNlX2ZhbWlseQ==::Q3ljbG9uZSBW::ZGV2aWNlX2ZhbWlseQ=="
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_PARAMETER "RU5BQkxFX01JRg==::ZmFsc2U=::RW5hYmxlIE1JRiBTdHJlYW1pbmc="
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_PARAMETER "RU5BQkxFX0JZVEVFTkFCTEU=::ZmFsc2U=::QWRkIGJ5dGVlbmFibGUgcG9ydA=="
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_PARAMETER "QllURUVOQUJMRV9XSURUSA==::NA==::QllURUVOQUJMRV9XSURUSA=="
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_PARAMETER "UkVDT05GSUdfQUREUl9XSURUSA==::Ng==::UkVDT05GSUdfQUREUl9XSURUSA=="
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_PARAMETER "UkVDT05GSUdfREFUQV9XSURUSA==::MzI=::UkVDT05GSUdfREFUQV9XSURUSA=="
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_PARAMETER "cmVjb25mX3dpZHRo::NjQ=::cmVjb25mX3dpZHRo"
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_COMPONENT_PARAMETER "V0FJVF9GT1JfTE9DSw==::dHJ1ZQ==::V0FJVF9GT1JfTE9DSw=="
set_global_assignment -library "pll_cfg" -name VERILOG_FILE [file join $::quartus(qip_path) "pll_cfg.v"]
set_global_assignment -library "pll_cfg" -name VERILOG_FILE [file join $::quartus(qip_path) "pll_cfg/altera_pll_reconfig_top.v"] set_global_assignment -library "pll_cfg" -name VERILOG_FILE [file join $::quartus(qip_path) "pll_cfg/altera_pll_reconfig_top.v"]
set_global_assignment -library "pll_cfg" -name VERILOG_FILE [file join $::quartus(qip_path) "pll_cfg/altera_pll_reconfig_core.v"] set_global_assignment -library "pll_cfg" -name VERILOG_FILE [file join $::quartus(qip_path) "pll_cfg/altera_pll_reconfig_core.v"]
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_TOOL_NAME "altera_pll_reconfig"
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_TOOL_VERSION "17.0"
set_global_assignment -entity "altera_pll_reconfig_top" -library "pll_cfg" -name IP_TOOL_ENV "mwpim"
+3 -3
View File
@@ -16,7 +16,7 @@
module altera_pll_reconfig_core module altera_pll_reconfig_core
#( #(
parameter reconf_width = 64, parameter reconf_width = 64,
parameter device_family = "Stratix V", parameter device_family = "Cyclone V",
// MIF Streaming parameters // MIF Streaming parameters
parameter RECONFIG_ADDR_WIDTH = 6, parameter RECONFIG_ADDR_WIDTH = 6,
parameter RECONFIG_DATA_WIDTH = 32, parameter RECONFIG_DATA_WIDTH = 32,
@@ -1883,7 +1883,7 @@ module fpll_dprio_init (
endmodule endmodule
module dyn_phase_shift module dyn_phase_shift
#( #(
parameter device_family = "Stratix V" parameter device_family = "Cyclone V"
) ( ) (
input wire clk, input wire clk,
@@ -2112,7 +2112,7 @@ endmodule
module generic_lcell_comb module generic_lcell_comb
#( #(
//parameter //parameter
parameter family = "Stratix V", parameter family = "Cyclone V",
parameter lut_mask = 64'hAAAAAAAAAAAAAAAA, parameter lut_mask = 64'hAAAAAAAAAAAAAAAA,
parameter dont_touch = "on" parameter dont_touch = "on"
) ( ) (
+1 -1
View File
@@ -16,7 +16,7 @@
module altera_pll_reconfig_top module altera_pll_reconfig_top
#( #(
parameter reconf_width = 64, parameter reconf_width = 64,
parameter device_family = "Stratix V", parameter device_family = "Cyclone V",
parameter RECONFIG_ADDR_WIDTH = 6, parameter RECONFIG_ADDR_WIDTH = 6,
parameter RECONFIG_DATA_WIDTH = 32, parameter RECONFIG_DATA_WIDTH = 32,
+86
View File
@@ -0,0 +1,86 @@
// megafunction wizard: %Altera PLL Reconfig v17.0%
// GENERATION: XML
// pll_cfg.v
// Generated using ACDS version 17.0 598
`timescale 1 ps / 1 ps
module pll_cfg #(
parameter ENABLE_BYTEENABLE = 0,
parameter BYTEENABLE_WIDTH = 4,
parameter RECONFIG_ADDR_WIDTH = 6,
parameter RECONFIG_DATA_WIDTH = 32,
parameter reconf_width = 64,
parameter WAIT_FOR_LOCK = 1
) (
input wire mgmt_clk, // mgmt_clk.clk
input wire mgmt_reset, // mgmt_reset.reset
output wire mgmt_waitrequest, // mgmt_avalon_slave.waitrequest
input wire mgmt_read, // .read
input wire mgmt_write, // .write
output wire [31:0] mgmt_readdata, // .readdata
input wire [5:0] mgmt_address, // .address
input wire [31:0] mgmt_writedata, // .writedata
output wire [63:0] reconfig_to_pll, // reconfig_to_pll.reconfig_to_pll
input wire [63:0] reconfig_from_pll // reconfig_from_pll.reconfig_from_pll
);
altera_pll_reconfig_top #(
.device_family ("Cyclone V"),
.ENABLE_MIF (0),
.MIF_FILE_NAME ("sys/pll_cfg.mif"),
.ENABLE_BYTEENABLE (ENABLE_BYTEENABLE),
.BYTEENABLE_WIDTH (BYTEENABLE_WIDTH),
.RECONFIG_ADDR_WIDTH (RECONFIG_ADDR_WIDTH),
.RECONFIG_DATA_WIDTH (RECONFIG_DATA_WIDTH),
.reconf_width (reconf_width),
.WAIT_FOR_LOCK (WAIT_FOR_LOCK)
) pll_cfg_inst (
.mgmt_clk (mgmt_clk), // mgmt_clk.clk
.mgmt_reset (mgmt_reset), // mgmt_reset.reset
.mgmt_waitrequest (mgmt_waitrequest), // mgmt_avalon_slave.waitrequest
.mgmt_read (mgmt_read), // .read
.mgmt_write (mgmt_write), // .write
.mgmt_readdata (mgmt_readdata), // .readdata
.mgmt_address (mgmt_address), // .address
.mgmt_writedata (mgmt_writedata), // .writedata
.reconfig_to_pll (reconfig_to_pll), // reconfig_to_pll.reconfig_to_pll
.reconfig_from_pll (reconfig_from_pll), // reconfig_from_pll.reconfig_from_pll
.mgmt_byteenable (4'b0000) // (terminated)
);
endmodule
// Retrieval info: <?xml version="1.0"?>
//<!--
// Generated by Altera MegaWizard Launcher Utility version 1.0
// ************************************************************
// THIS IS A WIZARD-GENERATED FILE. DO NOT EDIT THIS FILE!
// ************************************************************
// Copyright (C) 1991-2018 Altera Corporation
// Any megafunction design, and related net list (encrypted or decrypted),
// support information, device programming or simulation file, and any other
// associated documentation or information provided by Altera or a partner
// under Altera's Megafunction Partnership Program may be used only to
// program PLD devices (but not masked PLD devices) from Altera. Any other
// use of such megafunction design, net list, support information, device
// programming or simulation file, or any other related documentation or
// information is prohibited for any other purpose, including, but not
// limited to modification, reverse engineering, de-compiling, or use with
// any other silicon devices, unless such use is explicitly licensed under
// a separate agreement with Altera or a megafunction partner. Title to
// the intellectual property, including patents, copyrights, trademarks,
// trade secrets, or maskworks, embodied in any such megafunction design,
// net list, support information, device programming or simulation file, or
// any other related documentation or information provided by Altera or a
// megafunction partner, remains with Altera, the megafunction partner, or
// their respective licensors. No other licenses, including any licenses
// needed under any third party's intellectual property, are provided herein.
//-->
// Retrieval info: <instance entity-name="altera_pll_reconfig" version="17.0" >
// Retrieval info: <generic name="device_family" value="Cyclone V" />
// Retrieval info: <generic name="ENABLE_MIF" value="false" />
// Retrieval info: <generic name="MIF_FILE_NAME" value="sys/pll_cfg.mif" />
// Retrieval info: <generic name="ENABLE_BYTEENABLE" value="false" />
// Retrieval info: </instance>
// IPFS_FILES : pll_cfg.vo
// RELATED_FILES: pll_cfg.v, altera_pll_reconfig_top.v, altera_pll_reconfig_core.v, altera_std_synchronizer.v
File diff suppressed because it is too large. Load diff
+1 -4
View File
@@ -1,7 +1,4 @@
set_global_assignment -name QIP_FILE [file join $::quartus(qip_path) pll.13.qip ] set_global_assignment -name QIP_FILE [file join $::quartus(qip_path) pll.13.qip ]
set_global_assignment -name QIP_FILE [file join $::quartus(qip_path) pll_hdmi.13.qip ] set_global_assignment -name QIP_FILE [file join $::quartus(qip_path) pll_hdmi.13.qip ]
set_global_assignment -name QIP_FILE [file join $::quartus(qip_path) pll_audio.13.qip ] set_global_assignment -name QIP_FILE [file join $::quartus(qip_path) pll_audio.13.qip ]
set_global_assignment -name VERILOG_FILE [file join $::quartus(qip_path) pll_cfg.v ] set_global_assignment -name QIP_FILE [file join $::quartus(qip_path) pll_cfg.qip ]
set_global_assignment -name VERILOG_FILE [file join $::quartus(qip_path) pll_cfg/altera_pll_reconfig_core.v ]
set_global_assignment -name VERILOG_FILE [file join $::quartus(qip_path) pll_cfg/altera_pll_reconfig_top.v ]
set_global_assignment -name VERILOG_FILE [file join $::quartus(qip_path) pll_cfg_hdmi.v ]
+1 -2
View File
@@ -1,5 +1,4 @@
set_global_assignment -name QIP_FILE rtl/pll.qip set_global_assignment -name QIP_FILE rtl/pll.qip
set_global_assignment -name QIP_FILE [file join $::quartus(qip_path) pll_hdmi.qip ] set_global_assignment -name QIP_FILE [file join $::quartus(qip_path) pll_hdmi.qip ]
set_global_assignment -name QIP_FILE [file join $::quartus(qip_path) pll_audio.qip ] set_global_assignment -name QIP_FILE [file join $::quartus(qip_path) pll_audio.qip ]
#set_global_assignment -name QIP_FILE [file join $::quartus(qip_path) pll_cfg.qip ] set_global_assignment -name QIP_FILE [file join $::quartus(qip_path) pll_cfg.qip ]
set_global_assignment -name VERILOG_FILE [file join $::quartus(qip_path) pll_cfg_hdmi.v ]
+4 -4
View File
@@ -58,10 +58,10 @@ localparam DW = WIDE ? 15 : 7;
localparam SZ = OCTAL ? 8 : 1; localparam SZ = OCTAL ? 8 : 1;
localparam SW = SZ-1; localparam SW = SZ-1;
wire [7:0] DATA_TOKEN_CMD25 = 8'hfc; localparam DATA_TOKEN_CMD25 = 8'hfc;
wire [7:0] STOP_TRAN = 8'hfd; localparam STOP_TRAN = 8'hfd;
wire [7:0] DATA_TOKEN = 8'hfe; localparam DATA_TOKEN = 8'hfe;
wire [7:0] WRITE_DATA_RESPONSE = 8'h05; localparam WRITE_DATA_RESPONSE = 8'he5;
// number of bytes to wait after a command before sending the reply // number of bytes to wait after a command before sending the reply
localparam NCR = 5+3; // 5 bytes are required (command length) localparam NCR = 5+3; // 5 bytes are required (command length)
+2 -9
View File
@@ -16,13 +16,6 @@ set_location_assignment PIN_V10 -to ADC_SCK
set_location_assignment PIN_AC4 -to ADC_SDI set_location_assignment PIN_AC4 -to ADC_SDI
set_location_assignment PIN_AD4 -to ADC_SDO set_location_assignment PIN_AD4 -to ADC_SDO
#============================================================
# ARDUINO
#============================================================
set_instance_assignment -name IO_STANDARD "3.3-V LVTTL" -to ARDUINO_IO[*]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to ARDUINO_IO[*]
set_instance_assignment -name CURRENT_STRENGTH_NEW "MAXIMUM CURRENT" -to ARDUINO_IO[*]
#============================================================ #============================================================
# I2C LEDS/BUTTONS # I2C LEDS/BUTTONS
#============================================================ #============================================================
@@ -72,8 +65,8 @@ set_location_assignment PIN_AD17 -to SDRAM_A[11]
set_location_assignment PIN_D12 -to SDRAM_A[12] set_location_assignment PIN_D12 -to SDRAM_A[12]
set_location_assignment PIN_Y17 -to SDRAM_BA[0] set_location_assignment PIN_Y17 -to SDRAM_BA[0]
set_location_assignment PIN_AB25 -to SDRAM_BA[1] set_location_assignment PIN_AB25 -to SDRAM_BA[1]
set_location_assignment PIN_E8 -to SDRAM_DQ[0] set_location_assignment PIN_V12 -to SDRAM_DQ[0]
set_location_assignment PIN_V12 -to SDRAM_DQ[1] set_location_assignment PIN_E8 -to SDRAM_DQ[1]
set_location_assignment PIN_D11 -to SDRAM_DQ[2] set_location_assignment PIN_D11 -to SDRAM_DQ[2]
set_location_assignment PIN_W12 -to SDRAM_DQ[3] set_location_assignment PIN_W12 -to SDRAM_DQ[3]
set_location_assignment PIN_AH13 -to SDRAM_DQ[4] set_location_assignment PIN_AH13 -to SDRAM_DQ[4]
+5 -1
View File
@@ -25,6 +25,7 @@ set_false_path -from [get_ports {KEY*}]
set_false_path -from [get_ports {BTN_*}] set_false_path -from [get_ports {BTN_*}]
set_false_path -to [get_ports {LED_*}] set_false_path -to [get_ports {LED_*}]
set_false_path -to [get_ports {VGA_*}] set_false_path -to [get_ports {VGA_*}]
set_false_path -from [get_ports {VGA_EN}]
set_false_path -to [get_ports {AUDIO_SPDIF}] set_false_path -to [get_ports {AUDIO_SPDIF}]
set_false_path -to [get_ports {AUDIO_L}] set_false_path -to [get_ports {AUDIO_L}]
set_false_path -to [get_ports {AUDIO_R}] set_false_path -to [get_ports {AUDIO_R}]
@@ -34,6 +35,7 @@ set_false_path -from {cfg[*]}
set_false_path -from {VSET[*]} set_false_path -from {VSET[*]}
set_false_path -to {wcalc[*] hcalc[*]} set_false_path -to {wcalc[*] hcalc[*]}
set_false_path -to {hdmi_width[*] hdmi_height[*]} set_false_path -to {hdmi_width[*] hdmi_height[*]}
set_false_path -to {deb_* btn_en btn_up}
set_multicycle_path -to {*_osd|osd_vcnt*} -setup 2 set_multicycle_path -to {*_osd|osd_vcnt*} -setup 2
set_multicycle_path -to {*_osd|osd_vcnt*} -hold 1 set_multicycle_path -to {*_osd|osd_vcnt*} -hold 1
@@ -58,6 +60,7 @@ set_false_path -from {vol_att[*] scaler_flt[*] led_overtake[*] led_state[*]}
set_false_path -from {aflt_* acx* acy* areset* arc*} set_false_path -from {aflt_* acx* acy* areset* arc*}
set_false_path -from {arx* ary*} set_false_path -from {arx* ary*}
set_false_path -from {vs_line*} set_false_path -from {vs_line*}
set_false_path -from {ColorBurst_Range* PhaseInc* pal_en cvbs yc_en}
set_false_path -from {ascal|o_ihsize*} set_false_path -from {ascal|o_ihsize*}
set_false_path -from {ascal|o_ivsize*} set_false_path -from {ascal|o_ivsize*}
@@ -70,4 +73,5 @@ set_false_path -from {ascal|o_htotal* ascal|o_vtotal*}
set_false_path -from {ascal|o_hsstart* ascal|o_vsstart* ascal|o_hsend* ascal|o_vsend*} set_false_path -from {ascal|o_hsstart* ascal|o_vsstart* ascal|o_hsend* ascal|o_vsend*}
set_false_path -from {ascal|o_hsize* ascal|o_vsize*} set_false_path -from {ascal|o_hsize* ascal|o_vsize*}
set_false_path -from {mcp23009|sd_cd} set_false_path -from {mcp23009|flg_*}
set_false_path -to {sysmem|fpga_interfaces|clocks_resets|f2h*}
+183 -88
View File
@@ -72,7 +72,7 @@ module sys_top
output [5:0] VGA_R, output [5:0] VGA_R,
output [5:0] VGA_G, output [5:0] VGA_G,
output [5:0] VGA_B, output [5:0] VGA_B,
inout VGA_HS, // VGA_HS is secondary SD card detect when VGA_EN = 1 (inactive) inout VGA_HS,
output VGA_VS, output VGA_VS,
input VGA_EN, // active low input VGA_EN, // active low
@@ -125,27 +125,23 @@ module sys_top
); );
////////////////////// Secondary SD /////////////////////////////////// ////////////////////// Secondary SD ///////////////////////////////////
wire SD_CS, SD_CLK, SD_MOSI; wire SD_CS, SD_CLK, SD_MOSI, SD_MISO, SD_CD;
`ifndef MISTER_DUAL_SDRAM `ifndef MISTER_DUAL_SDRAM
wire sd_miso = SW[3] | SDIO_DAT[0]; wire sd_cd = SDCD_SPDIF & ~SW[2]; // SW[2]=ON workaround for faulty boards without SD card detect pin.
`else assign SD_CD = mcp_en ? mcp_sdcd : sd_cd;
wire sd_miso = 1; assign SD_MISO = SD_CD | (mcp_en ? SD_SPI_MISO : (VGA_EN | SDIO_DAT[0]));
`endif assign SD_SPI_CS = mcp_en ? (mcp_sdcd ? 1'bZ : SD_CS) : (sog & ~cs1 & ~VGA_EN) ? 1'b1 : 1'bZ;
wire SD_MISO = mcp_sdcd ? sd_miso : SD_SPI_MISO; assign SD_SPI_CLK = (~mcp_en | mcp_sdcd) ? 1'bZ : SD_CLK;
assign SD_SPI_MOSI = (~mcp_en | mcp_sdcd) ? 1'bZ : SD_MOSI;
`ifndef MISTER_DUAL_SDRAM assign {SDIO_CLK,SDIO_CMD,SDIO_DAT} = av_dis ? 6'bZZZZZZ : (mcp_en | sd_cd) ? {vga_g,vga_r,vga_b} : {SD_CLK,SD_MOSI,SD_CS,3'bZZZ};
assign SDIO_DAT[2:1]= 2'bZZ;
assign SDIO_DAT[3] = SW[3] ? 1'bZ : SD_CS;
assign SDIO_CLK = SW[3] ? 1'bZ : SD_CLK;
assign SDIO_CMD = SW[3] ? 1'bZ : SD_MOSI;
assign SD_SPI_CS = mcp_sdcd ? ((~VGA_EN & sog & ~cs1) ? 1'b1 : 1'bZ) : SD_CS;
`else `else
assign SD_CD = mcp_sdcd;
assign SD_MISO = mcp_sdcd | SD_SPI_MISO;
assign SD_SPI_CS = mcp_sdcd ? 1'bZ : SD_CS; assign SD_SPI_CS = mcp_sdcd ? 1'bZ : SD_CS;
`endif
assign SD_SPI_CLK = mcp_sdcd ? 1'bZ : SD_CLK; assign SD_SPI_CLK = mcp_sdcd ? 1'bZ : SD_CLK;
assign SD_SPI_MOSI = mcp_sdcd ? 1'bZ : SD_MOSI; assign SD_SPI_MOSI = mcp_sdcd ? 1'bZ : SD_MOSI;
`endif
////////////////////// LEDs/Buttons /////////////////////////////////// ////////////////////// LEDs/Buttons ///////////////////////////////////
@@ -157,36 +153,59 @@ wire led_d = led_disk[1] ? ~led_disk[0] : ~(led_disk[0] | gp_out[29]);
wire led_u = ~led_user; wire led_u = ~led_user;
wire led_locked; wire led_locked;
`ifndef MISTER_DUAL_SDRAM //LEDs on de10-nano board
assign LED_POWER = (SW[3] | led_p) ? 1'bZ : 1'b0;
assign LED_HDD = (SW[3] | led_d) ? 1'bZ : 1'b0;
assign LED_USER = (SW[3] | led_u) ? 1'bZ : 1'b0;
`endif
//LEDs on main board
assign LED = (led_overtake & led_state) | (~led_overtake & {1'b0,led_locked,1'b0, ~led_p, 1'b0, ~led_d, 1'b0, ~led_u}); assign LED = (led_overtake & led_state) | (~led_overtake & {1'b0,led_locked,1'b0, ~led_p, 1'b0, ~led_d, 1'b0, ~led_u});
wire btn_r, btn_o, btn_u;
`ifdef MISTER_DUAL_SDRAM
assign {btn_r,btn_o,btn_u} = SW[3] ? {mcp_btn[1],mcp_btn[2],mcp_btn[0]} : ~{SDRAM2_DQ[9],SDRAM2_DQ[13],SDRAM2_DQ[11]};
`else
assign {btn_r,btn_o,btn_u} = ~{BTN_RESET,BTN_OSD,BTN_USER} | {mcp_btn[1],mcp_btn[2],mcp_btn[0]};
`endif
wire [2:0] mcp_btn; wire [2:0] mcp_btn;
wire mcp_sdcd; wire mcp_sdcd;
wire mcp_en;
wire mcp_mode;
mcp23009 mcp23009 mcp23009 mcp23009
( (
.clk(FPGA_CLK2_50), .clk(FPGA_CLK2_50),
.btn(mcp_btn), .btn(mcp_btn),
.led({led_p, led_d, led_u}), .led({led_p, led_d, led_u}),
.sd_cd(mcp_sdcd), .flg_sd_cd(mcp_sdcd),
.flg_present(mcp_en),
.flg_mode(mcp_mode),
.scl(IO_SCL), .scl(IO_SCL),
.sda(IO_SDA) .sda(IO_SDA)
); );
wire io_dig = mcp_en ? mcp_mode : SW[3];
`ifndef MISTER_DUAL_SDRAM
wire av_dis = io_dig | VGA_EN;
assign LED_POWER = av_dis ? 1'bZ : mcp_en ? de1 : led_p ? 1'bZ : 1'b0;
assign LED_HDD = av_dis ? 1'bZ : mcp_en ? (sog & ~cs1) : led_d ? 1'bZ : 1'b0;
//assign LED_USER = av_dis ? 1'bZ : mcp_en ? ~vga_tx_clk : led_u ? 1'bZ : 1'b0;
assign LED_USER = VGA_TX_CLK;
wire BTN_DIS = VGA_EN;
`else
wire BTN_RESET = 1'b1;
wire BTN_OSD = 1'b1;
wire BTN_USER = 1'b1;
wire BTN_DIS = 1'b1;
`endif
reg BTN_EN = 0;
reg [25:0] btn_timeout = 0;
initial btn_timeout = 0;
always @(posedge FPGA_CLK2_50) begin
reg btn_up = 0;
reg btn_en = 0;
btn_up <= BTN_RESET & BTN_OSD & BTN_USER;
if(~reset & btn_up & ~&btn_timeout) btn_timeout <= btn_timeout + 1'd1;
btn_en <= ~BTN_DIS;
BTN_EN <= &btn_timeout & btn_en;
end
wire btn_r = (mcp_en | SW[3]) ? mcp_btn[1] : (BTN_EN & ~BTN_RESET);
wire btn_o = (mcp_en | SW[3]) ? mcp_btn[2] : (BTN_EN & ~BTN_OSD );
wire btn_u = (mcp_en | SW[3]) ? mcp_btn[0] : (BTN_EN & ~BTN_USER );
reg btn_user, btn_osd; reg btn_user, btn_osd;
always @(posedge FPGA_CLK2_50) begin always @(posedge FPGA_CLK2_50) begin
@@ -212,7 +231,7 @@ end
// gp_in[31] = 0 - quick flag that FPGA is initialized (HPS reads 1 when FPGA is not in user mode) // gp_in[31] = 0 - quick flag that FPGA is initialized (HPS reads 1 when FPGA is not in user mode)
// used to avoid lockups while JTAG loading // used to avoid lockups while JTAG loading
wire [31:0] gp_in = {1'b0, btn_user | btn[1], btn_osd | btn[0], SW[3], 8'd0, io_ver, io_ack, io_wide, io_dout | io_dout_sys}; wire [31:0] gp_in = {1'b0, btn_user | btn[1], btn_osd | btn[0], io_dig, 8'd0, io_ver, io_ack, io_wide, io_dout | io_dout_sys};
wire [31:0] gp_out; wire [31:0] gp_out;
wire [1:0] io_ver = 1; // 0 - obsolete. 1 - optimized HPS I/O. 2,3 - reserved for future. wire [1:0] io_ver = 1; // 0 - obsolete. 1 - optimized HPS I/O. 2,3 - reserved for future.
@@ -267,13 +286,13 @@ cyclonev_hps_interface_mpu_general_purpose h2f_gp
reg [15:0] cfg; reg [15:0] cfg;
reg cfg_set = 0; reg cfg_set = 0;
wire vga_fb = cfg[12] | vga_force_scaler;
`ifdef MISTER_DEBUG_NOHDMI `ifdef MISTER_DEBUG_NOHDMI
wire vga_fb = 0;
wire direct_video = 1; wire direct_video = 1;
`else `else
wire vga_fb = cfg[12] | vga_force_scaler;
wire direct_video = cfg[10]; wire direct_video = cfg[10];
`endif `endif
@@ -281,10 +300,15 @@ wire audio_96k = cfg[6];
wire csync_en = cfg[3]; wire csync_en = cfg[3];
wire io_osd_vga = io_ss1 & ~io_ss2; wire io_osd_vga = io_ss1 & ~io_ss2;
`ifndef MISTER_DUAL_SDRAM `ifndef MISTER_DUAL_SDRAM
wire forced_scandoubler = cfg[4];
wire ypbpr_en = cfg[5]; wire ypbpr_en = cfg[5];
wire sog = cfg[9]; wire sog = cfg[9];
`ifdef MISTER_DEBUG_NOHDMI
wire vga_scaler = 0;
`else
wire vga_scaler = cfg[2] | vga_force_scaler; wire vga_scaler = cfg[2] | vga_force_scaler;
`endif `endif
`endif
reg cfg_custom_t = 0; reg cfg_custom_t = 0;
reg [5:0] cfg_custom_p1; reg [5:0] cfg_custom_p1;
@@ -309,6 +333,7 @@ reg [11:0] vs_line = 0;
reg scaler_out = 0; reg scaler_out = 0;
reg vrr_mode = 0; reg vrr_mode = 0;
wire hdmi_blackout;
reg [31:0] aflt_rate = 7056000; reg [31:0] aflt_rate = 7056000;
reg [39:0] acx = 4258969; reg [39:0] acx = 4258969;
@@ -370,6 +395,7 @@ always@(posedge clk_sys) begin
`ifndef MISTER_DEBUG_NOHDMI `ifndef MISTER_DEBUG_NOHDMI
if(io_din[7:0] == 'h40) io_dout_sys <= fb_crc; if(io_din[7:0] == 'h40) io_dout_sys <= fb_crc;
`endif `endif
if(io_din[7:0] == 'h42) io_dout_sys <= {1'b1, frame_cnt};
end end
else begin else begin
cnt <= cnt + 1'd1; cnt <= cnt + 1'd1;
@@ -476,18 +502,22 @@ always@(posedge clk_sys) begin
endcase endcase
end end
`endif `endif
`ifndef MISTER_DISABLE_YC
if(cmd == 'h41) begin if(cmd == 'h41) begin
case(cnt[3:0]) case(cnt[3:0])
`ifndef MISTER_DISABLE_YC
0: {pal_en,cvbs,yc_en} <= io_din[2:0]; 0: {pal_en,cvbs,yc_en} <= io_din[2:0];
4: ColorBurst_Range[15:0] <= io_din;
5: ColorBurst_Range[16] <= io_din[0];
`endif
// Subcarrier commands (independent of YC module)
1: PhaseInc[15:0] <= io_din; 1: PhaseInc[15:0] <= io_din;
2: PhaseInc[31:16] <= io_din; 2: PhaseInc[31:16] <= io_din;
3: PhaseInc[39:32] <= io_din[7:0]; 3: PhaseInc[39:32] <= io_din[7:0];
4: ColorBurst_Range[15:0] <= io_din; `ifndef MISTER_DUAL_SDRAM
5: ColorBurst_Range[16] <= io_din[0]; 6: subcarrier <= io_din[0];
`endif
endcase endcase
end end
`endif
end end
end end
@@ -506,6 +536,15 @@ always@(posedge clk_sys) begin
if(~vs_d2 & vs_d1) vs_wait <= 0; if(~vs_d2 & vs_d1) vs_wait <= 0;
end end
reg [7:0] frame_cnt;
always @(posedge clk_sys) begin
reg vs_r, vs_old;
vs_r <= vs_fix;
if(vs_r == vs_fix) vs_old <= vs_r;
if(~vs_old & vs_r) frame_cnt <= frame_cnt + 1'd1;
end
cyclonev_hps_interface_peripheral_uart uart cyclonev_hps_interface_peripheral_uart uart
( (
.ri(0), .ri(0),
@@ -655,6 +694,7 @@ wire vbuf_write;
wire [23:0] hdmi_data; wire [23:0] hdmi_data;
wire hdmi_vs, hdmi_hs, hdmi_de, hdmi_vbl, hdmi_brd; wire hdmi_vs, hdmi_hs, hdmi_de, hdmi_vbl, hdmi_brd;
wire freeze; wire freeze;
wire bob_deint;
`ifndef MISTER_DEBUG_NOHDMI `ifndef MISTER_DEBUG_NOHDMI
wire clk_hdmi = hdmi_clk_out; wire clk_hdmi = hdmi_clk_out;
@@ -689,6 +729,7 @@ ascal
.reset_na (~reset_req), .reset_na (~reset_req),
.run (1), .run (1),
.freeze (freeze), .freeze (freeze),
.bob_deint (bob_deint),
.i_clk (clk_ihdmi), .i_clk (clk_ihdmi),
.i_ce (ce_hpix), .i_ce (ce_hpix),
@@ -730,6 +771,7 @@ ascal
.vmax (vmax), .vmax (vmax),
.vrr (vrr_mode), .vrr (vrr_mode),
.vrrmax (HEIGHT + VBP + VS[11:0] + 12'd1), .vrrmax (HEIGHT + VBP + VS[11:0] + 12'd1),
.swblack (hdmi_blackout),
.mode ({~lowlat,LFB_EN ? LFB_FLT : |scaler_flt,2'b00}), .mode ({~lowlat,LFB_EN ? LFB_FLT : |scaler_flt,2'b00}),
.poly_clk (clk_sys), .poly_clk (clk_sys),
@@ -1065,11 +1107,8 @@ always @(posedge FPGA_CLK1_50) begin
old_wait <= adj_waitrequest; old_wait <= adj_waitrequest;
if(old_wait & ~adj_waitrequest & gotd) cfg_ready <= 1; if(old_wait & ~adj_waitrequest & gotd) cfg_ready <= 1;
end end
`else `else
wire cfg_ready = 1; wire cfg_ready = 1;
`endif `endif
assign HDMI_I2C_SCL = hdmi_scl_en ? 1'b0 : 1'bZ; assign HDMI_I2C_SCL = hdmi_scl_en ? 1'b0 : 1'bZ;
@@ -1085,7 +1124,6 @@ cyclonev_hps_interface_peripheral_i2c hdmi_i2c
); );
`ifndef MISTER_DEBUG_NOHDMI `ifndef MISTER_DEBUG_NOHDMI
`ifdef MISTER_FB `ifdef MISTER_FB
reg dis_output; reg dis_output;
always @(posedge clk_hdmi) begin always @(posedge clk_hdmi) begin
@@ -1146,10 +1184,10 @@ osd hdmi_osd
.vs_out(hdmi_vs_osd), .vs_out(hdmi_vs_osd),
.de_out(hdmi_de_osd) .de_out(hdmi_de_osd)
); );
`endif
wire hdmi_cs_osd; wire hdmi_cs_osd;
csync csync_hdmi(clk_hdmi, hdmi_hs_osd, hdmi_vs_osd, hdmi_cs_osd); csync csync_hdmi(clk_hdmi, hdmi_hs_osd, hdmi_vs_osd, hdmi_cs_osd);
`endif
reg [23:0] dv_data; reg [23:0] dv_data;
reg dv_hs, dv_vs, dv_de; reg dv_hs, dv_vs, dv_de;
@@ -1260,10 +1298,17 @@ always @(posedge hdmi_tx_clk) begin
hdmi_dv_vs <= dv_vs; hdmi_dv_vs <= dv_vs;
hdmi_dv_de <= dv_de; hdmi_dv_de <= dv_de;
`ifndef MISTER_DEBUG_NOHDMI
hs <= (~vga_fb & direct_video) ? hdmi_dv_hs : (direct_video & csync_en) ? hdmi_cs_osd : hdmi_hs_osd; hs <= (~vga_fb & direct_video) ? hdmi_dv_hs : (direct_video & csync_en) ? hdmi_cs_osd : hdmi_hs_osd;
vs <= (~vga_fb & direct_video) ? hdmi_dv_vs : hdmi_vs_osd; vs <= (~vga_fb & direct_video) ? hdmi_dv_vs : hdmi_vs_osd;
de <= (~vga_fb & direct_video) ? hdmi_dv_de : hdmi_de_osd; de <= (~vga_fb & direct_video) ? hdmi_dv_de : hdmi_de_osd;
d <= (~vga_fb & direct_video) ? hdmi_dv_data : hdmi_data_osd; d <= (~vga_fb & direct_video) ? hdmi_dv_data : hdmi_data_osd;
`else
hs <= hdmi_dv_hs;
vs <= hdmi_dv_vs;
de <= hdmi_dv_de;
d <= hdmi_dv_data;
`endif
hdmi_out_hs <= hs; hdmi_out_hs <= hs;
hdmi_out_vs <= vs; hdmi_out_vs <= vs;
@@ -1278,6 +1323,46 @@ assign HDMI_TX_D = hdmi_out_d;
///////////////////////// VGA output ////////////////////////////////// ///////////////////////// VGA output //////////////////////////////////
`ifndef MISTER_DUAL_SDRAM
wire vga_tx_clk;
`ifndef MISTER_DEBUG_NOHDMI
cyclonev_clkselect vga_clk_sw
(
.clkselect({1'b1, ~vga_fb & ~vga_scaler}),
.inclk({clk_vid, hdmi_clk_out, 2'b00}),
.outclk(vga_tx_clk)
);
`else
assign vga_tx_clk = clk_vid;
`endif
wire VGA_TX_CLK;
altddio_out
#(
.extend_oe_disable("OFF"),
.intended_device_family("Cyclone V"),
.invert_output("OFF"),
.lpm_hint("UNUSED"),
.lpm_type("altddio_out"),
.oe_reg("UNREGISTERED"),
.power_up_high("OFF"),
.width(1)
)
vgaclk_ddr
(
.datain_h(1'b0),
.datain_l(1'b1),
.outclock(vga_tx_clk),
.dataout(VGA_TX_CLK),
.aclr(~mcp_en & ~av_dis),
.aset(1'b0),
.oe(~av_dis & (mcp_en | ~led_u)),
.outclocken(1'b1),
.sclr(1'b0),
.sset(1'b0)
);
`endif
wire [23:0] vga_data_sl; wire [23:0] vga_data_sl;
wire vga_de_sl, vga_ce_sl, vga_vs_sl, vga_hs_sl; wire vga_de_sl, vga_ce_sl, vga_vs_sl, vga_hs_sl;
scanlines #(0) VGA_scanlines scanlines #(0) VGA_scanlines
@@ -1299,7 +1384,7 @@ scanlines #(0) VGA_scanlines
); );
wire [23:0] vga_data_osd; wire [23:0] vga_data_osd;
wire vga_vs_osd, vga_hs_osd; wire vga_vs_osd, vga_hs_osd, vga_de_osd;
osd vga_osd osd vga_osd
( (
.clk_sys(clk_sys), .clk_sys(clk_sys),
@@ -1317,7 +1402,8 @@ osd vga_osd
.dout(vga_data_osd), .dout(vga_data_osd),
.hs_out(vga_hs_osd), .hs_out(vga_hs_osd),
.vs_out(vga_vs_osd) .vs_out(vga_vs_osd),
.de_out(vga_de_osd)
); );
wire vga_cs_osd; wire vga_cs_osd;
@@ -1328,9 +1414,8 @@ csync csync_vga(clk_vid, vga_hs_osd, vga_vs_osd, vga_cs_osd);
reg yc_en; reg yc_en;
reg cvbs; reg cvbs;
reg [16:0] ColorBurst_Range; reg [16:0] ColorBurst_Range;
reg [39:0] PhaseInc;
wire [23:0] yc_o; wire [23:0] yc_o;
wire yc_hs, yc_vs, yc_cs; wire yc_hs, yc_vs, yc_cs, yc_de;
yc_out yc_out yc_out yc_out
( (
@@ -1342,18 +1427,34 @@ csync csync_vga(clk_vid, vga_hs_osd, vga_vs_osd, vga_cs_osd);
.hsync(vga_hs_osd), .hsync(vga_hs_osd),
.vsync(vga_vs_osd), .vsync(vga_vs_osd),
.csync(vga_cs_osd), .csync(vga_cs_osd),
.de(vga_de_osd),
.dout(yc_o), .dout(yc_o),
.din(vga_data_osd), .din(vga_data_osd),
.hsync_o(yc_hs), .hsync_o(yc_hs),
.vsync_o(yc_vs), .vsync_o(yc_vs),
.csync_o(yc_cs) .csync_o(yc_cs),
.de_o(yc_de)
); );
`endif `endif
reg [39:0] PhaseInc;
`ifndef MISTER_DUAL_SDRAM `ifndef MISTER_DUAL_SDRAM
// Subcarrier generation for external encoders (independent of YC module)
reg subcarrier;
reg [39:0] sub_accum;
always @(posedge clk_vid) sub_accum <= sub_accum + PhaseInc;
// 1-bit output for positive/negative of wave, no LUT required. Output 1 if disabled for further logic
reg subcarrier_out;
always @(posedge clk_vid) subcarrier_out <= ~(subcarrier & csync_en & ~ypbpr_en & ~forced_scandoubler & ~vgas_en) | sub_accum[39];
wire VGA_DISABLE; wire VGA_DISABLE;
wire [23:0] vgas_o; wire [23:0] vgas_o;
wire vgas_hs, vgas_vs, vgas_cs; wire vgas_hs, vgas_vs, vgas_cs, vgas_de;
`ifndef MISTER_DEBUG_NOHDMI
vga_out vga_scaler_out vga_out vga_scaler_out
( (
.clk(clk_hdmi), .clk(clk_hdmi),
@@ -1361,15 +1462,20 @@ csync csync_vga(clk_vid, vga_hs_osd, vga_vs_osd, vga_cs_osd);
.hsync(hdmi_hs_osd), .hsync(hdmi_hs_osd),
.vsync(hdmi_vs_osd), .vsync(hdmi_vs_osd),
.csync(hdmi_cs_osd), .csync(hdmi_cs_osd),
.de(hdmi_de_osd),
.dout(vgas_o), .dout(vgas_o),
.din({24{hdmi_de_osd}} & hdmi_data_osd), .din({24{hdmi_de_osd}} & hdmi_data_osd),
.hsync_o(vgas_hs), .hsync_o(vgas_hs),
.vsync_o(vgas_vs), .vsync_o(vgas_vs),
.csync_o(vgas_cs) .csync_o(vgas_cs),
.de_o(vgas_de)
); );
`else
assign {vgas_o, vgas_hs, vgas_vs, vgas_cs, vgas_de} = 0;
`endif
wire [23:0] vga_o, vga_o_t; wire [23:0] vga_o, vga_o_t;
wire vga_hs, vga_vs, vga_cs, vga_hs_t, vga_vs_t, vga_cs_t; wire vga_hs, vga_vs, vga_cs, vga_de, vga_hs_t, vga_vs_t, vga_cs_t, vga_de_t;
vga_out vga_out vga_out vga_out
( (
.clk(clk_vid), .clk(clk_vid),
@@ -1377,26 +1483,35 @@ csync csync_vga(clk_vid, vga_hs_osd, vga_vs_osd, vga_cs_osd);
.hsync(vga_hs_osd), .hsync(vga_hs_osd),
.vsync(vga_vs_osd), .vsync(vga_vs_osd),
.csync(vga_cs_osd), .csync(vga_cs_osd),
.de(vga_de_osd),
.dout(vga_o_t), .dout(vga_o_t),
.din(vga_data_osd), .din(vga_data_osd),
.hsync_o(vga_hs_t), .hsync_o(vga_hs_t),
.vsync_o(vga_vs_t), .vsync_o(vga_vs_t),
.csync_o(vga_cs_t) .csync_o(vga_cs_t),
.de_o(vga_de_t)
); );
`ifndef MISTER_DISABLE_YC `ifndef MISTER_DISABLE_YC
assign {vga_o, vga_hs, vga_vs, vga_cs } = ~yc_en ? {vga_o_t, vga_hs_t, vga_vs_t, vga_cs_t } : {yc_o, yc_hs, yc_vs, yc_cs }; assign {vga_o, vga_hs, vga_vs, vga_cs, vga_de } = ~yc_en ? {vga_o_t, vga_hs_t, vga_vs_t, vga_cs_t, vga_de_t } : {yc_o, yc_hs, yc_vs, yc_cs, yc_de };
`else `else
assign {vga_o, vga_hs, vga_vs, vga_cs } = {vga_o_t, vga_hs_t, vga_vs_t, vga_cs_t } ; assign {vga_o, vga_hs, vga_vs, vga_cs, vga_de } = {vga_o_t, vga_hs_t, vga_vs_t, vga_cs_t, vga_de_t } ;
`endif `endif
wire cs1 = (vga_fb | vga_scaler) ? vgas_cs : vga_cs; wire vgas_en = vga_fb | vga_scaler;
assign VGA_VS = (VGA_EN | SW[3]) ? 1'bZ : (((vga_fb | vga_scaler) ? (~vgas_vs ^ VS[12]) : VGA_DISABLE ? 1'd1 : ~vga_vs) | csync_en); wire cs1 = vgas_en ? vgas_cs : vga_cs;
assign VGA_HS = (VGA_EN | SW[3]) ? 1'bZ : ((vga_fb | vga_scaler) ? ((csync_en ? ~vgas_cs : ~vgas_hs) ^ HS[12]) : VGA_DISABLE ? 1'd1 : (csync_en ? ~vga_cs : ~vga_hs)); wire de1 = vgas_en ? vgas_de : vga_de;
assign VGA_R = (VGA_EN | SW[3]) ? 6'bZZZZZZ : (vga_fb | vga_scaler) ? vgas_o[23:18] : VGA_DISABLE ? 6'd0 : vga_o[23:18];
assign VGA_G = (VGA_EN | SW[3]) ? 6'bZZZZZZ : (vga_fb | vga_scaler) ? vgas_o[15:10] : VGA_DISABLE ? 6'd0 : vga_o[15:10]; assign VGA_VS = av_dis ? 1'bZ :(((vgas_en ? (~vgas_vs ^ VS[12]) : VGA_DISABLE ? 1'd1 : ~vga_vs) | csync_en) & subcarrier_out);
assign VGA_B = (VGA_EN | SW[3]) ? 6'bZZZZZZ : (vga_fb | vga_scaler) ? vgas_o[7:2] : VGA_DISABLE ? 6'd0 : vga_o[7:2] ; assign VGA_HS = av_dis ? 1'bZ : (vgas_en ? ((csync_en ? ~vgas_cs : ~vgas_hs) ^ HS[12]) : VGA_DISABLE ? 1'd1 : (csync_en ? ~vga_cs : ~vga_hs));
assign VGA_R = av_dis ? 6'bZZZZZZ : vgas_en ? vgas_o[23:18] : VGA_DISABLE ? 6'd0 : vga_o[23:18];
assign VGA_G = av_dis ? 6'bZZZZZZ : vgas_en ? vgas_o[15:10] : VGA_DISABLE ? 6'd0 : vga_o[15:10];
assign VGA_B = av_dis ? 6'bZZZZZZ : vgas_en ? vgas_o[7:2] : VGA_DISABLE ? 6'd0 : vga_o[7:2] ;
wire [1:0] vga_r = vgas_en ? vgas_o[17:16] : VGA_DISABLE ? 2'd0 : vga_o[17:16];
wire [1:0] vga_g = vgas_en ? vgas_o[9:8] : VGA_DISABLE ? 2'd0 : vga_o[9:8];
wire [1:0] vga_b = vgas_en ? vgas_o[1:0] : VGA_DISABLE ? 2'd0 : vga_o[1:0];
`endif `endif
reg video_sync = 0; reg video_sync = 0;
@@ -1426,14 +1541,14 @@ end
///////////////////////// Audio output //////////////////////////////// ///////////////////////// Audio output ////////////////////////////////
assign SDCD_SPDIF =(SW[3] & ~spdif) ? 1'b0 : 1'bZ; assign SDCD_SPDIF = (mcp_en & ~spdif) ? 1'b0 : 1'bZ;
`ifndef MISTER_DUAL_SDRAM `ifndef MISTER_DUAL_SDRAM
wire analog_l, analog_r; wire analog_l, analog_r;
assign AUDIO_SPDIF = SW[3] ? 1'bZ : SW[0] ? HDMI_LRCLK : spdif; assign AUDIO_SPDIF = av_dis ? 1'bZ : (SW[0] | mcp_en) ? HDMI_LRCLK : spdif;
assign AUDIO_R = SW[3] ? 1'bZ : SW[0] ? HDMI_I2S : analog_r; assign AUDIO_R = av_dis ? 1'bZ : (SW[0] | mcp_en) ? HDMI_I2S : analog_r;
assign AUDIO_L = SW[3] ? 1'bZ : SW[0] ? HDMI_SCLK : analog_l; assign AUDIO_L = av_dis ? 1'bZ : (SW[0] | mcp_en) ? HDMI_SCLK : analog_l;
`endif `endif
assign HDMI_MCLK = clk_audio; assign HDMI_MCLK = clk_audio;
@@ -1651,6 +1766,8 @@ emu emu
.HDMI_WIDTH(direct_video ? 12'd0 : hdmi_width), .HDMI_WIDTH(direct_video ? 12'd0 : hdmi_width),
.HDMI_HEIGHT(direct_video ? 12'd0 : hdmi_height), .HDMI_HEIGHT(direct_video ? 12'd0 : hdmi_height),
.HDMI_FREEZE(freeze), .HDMI_FREEZE(freeze),
.HDMI_BLACKOUT(hdmi_blackout),
.HDMI_BOB_DEINT(bob_deint),
.CLK_VIDEO(clk_vid), .CLK_VIDEO(clk_vid),
.CE_PIXEL(ce_pix), .CE_PIXEL(ce_pix),
@@ -1723,7 +1840,7 @@ emu emu
.SDRAM2_nRAS(SDRAM2_nRAS), .SDRAM2_nRAS(SDRAM2_nRAS),
.SDRAM2_nCAS(SDRAM2_nCAS), .SDRAM2_nCAS(SDRAM2_nCAS),
.SDRAM2_CLK(SDRAM2_CLK), .SDRAM2_CLK(SDRAM2_CLK),
.SDRAM2_EN(SW[3]), .SDRAM2_EN(io_dig),
`endif `endif
.BUTTONS(btn), .BUTTONS(btn),
@@ -1733,11 +1850,7 @@ emu emu
.SD_MOSI(SD_MOSI), .SD_MOSI(SD_MOSI),
.SD_MISO(SD_MISO), .SD_MISO(SD_MISO),
.SD_CS(SD_CS), .SD_CS(SD_CS),
`ifdef MISTER_DUAL_SDRAM .SD_CD(SD_CD),
.SD_CD(mcp_sdcd),
`else
.SD_CD(mcp_sdcd & (SW[0] ? VGA_HS : (SW[3] | SDCD_SPDIF))),
`endif
.UART_CTS(uart_rts), .UART_CTS(uart_rts),
.UART_RTS(uart_cts), .UART_RTS(uart_cts),
@@ -1779,24 +1892,6 @@ always @(posedge clk) begin
end end
end end
/*
always @(posedge clk) begin
integer pos = 0, neg = 0, cnt = 0;
reg s1,s2;
s1 <= sync_in;
s2 <= s1;
if(~s2 & s1) neg <= cnt;
if(s2 & ~s1) pos <= cnt;
cnt <= cnt + 1;
if(s2 != s1) cnt <= 0;
pol <= pos > neg;
end
*/
endmodule endmodule
///////////////////////////////////////////////////////////////////// /////////////////////////////////////////////////////////////////////
+6 -3
View File
@@ -7,13 +7,15 @@ module vga_out
input hsync, input hsync,
input vsync, input vsync,
input csync, input csync,
input de,
input [23:0] din, input [23:0] din,
output [23:0] dout, output [23:0] dout,
output reg hsync_o, output reg hsync_o,
output reg vsync_o, output reg vsync_o,
output reg csync_o output reg csync_o,
output reg de_o
); );
wire [7:0] red = din[23:16]; wire [7:0] red = din[23:16];
@@ -35,8 +37,8 @@ always @(posedge clk) begin
reg [18:0] y_1b, pb_1b, pr_1b; reg [18:0] y_1b, pb_1b, pr_1b;
reg [18:0] y_2, pb_2, pr_2; reg [18:0] y_2, pb_2, pr_2;
reg [23:0] din1, din2; reg [23:0] din1, din2;
reg hsync2, vsync2, csync2; reg hsync2, vsync2, csync2, de2;
reg hsync1, vsync1, csync1; reg hsync1, vsync1, csync1, de1;
y_1r <= {red, 6'd0} + {red, 3'd0} + {red, 2'd0} + red; y_1r <= {red, 6'd0} + {red, 3'd0} + {red, 2'd0} + red;
pb_1r <= 19'd32768 - ({red, 5'd0} + {red, 3'd0} + {red, 1'd0}); pb_1r <= 19'd32768 - ({red, 5'd0} + {red, 3'd0} + {red, 1'd0});
@@ -61,6 +63,7 @@ always @(posedge clk) begin
hsync_o <= hsync2; hsync2 <= hsync1; hsync1 <= hsync; hsync_o <= hsync2; hsync2 <= hsync1; hsync1 <= hsync;
vsync_o <= vsync2; vsync2 <= vsync1; vsync1 <= vsync; vsync_o <= vsync2; vsync2 <= vsync1; vsync1 <= vsync;
csync_o <= csync2; csync2 <= csync1; csync1 <= csync; csync_o <= csync2; csync2 <= csync1; csync1 <= csync;
de_o <= de2; de2 <= de1; de1 <= de;
rgb <= din2; din2 <= din1; din1 <= din; rgb <= din2; din2 <= din1; din1 <= din;
end end
+10 -1
View File
@@ -26,6 +26,10 @@ module video_cleaner
//optional de //optional de
input DE_in, input DE_in,
//optional interlace support
input interlace,
input f1,
// video output signals // video output signals
output reg [7:0] VGA_R, output reg [7:0] VGA_R,
output reg [7:0] VGA_G, output reg [7:0] VGA_G,
@@ -56,16 +60,21 @@ always @(posedge clk_vid) begin
HBlank_out <= hbl; HBlank_out <= hbl;
VGA_HS <= hs; VGA_HS <= hs;
if(~VGA_HS & hs) VGA_VS <= vs;
VGA_R <= R; VGA_R <= R;
VGA_G <= G; VGA_G <= G;
VGA_B <= B; VGA_B <= B;
DE_out <= DE_in; DE_out <= DE_in;
if (interlace & f1) begin
VGA_VS <= vs;
VBlank_out <= vbl;
end else begin
if(~VGA_HS & hs) VGA_VS <= vs;
if(HBlank_out & ~hbl) VBlank_out <= vbl; if(HBlank_out & ~hbl) VBlank_out <= vbl;
end end
end end
end
endmodule endmodule
+21 -10
View File
@@ -170,10 +170,8 @@ reg [11:0] mul_arg1, mul_arg2;
wire [23:0] mul_res; wire [23:0] mul_res;
sys_umul #(12,12) mul(CLK_VIDEO,mul_start,mul_run, mul_arg1,mul_arg2,mul_res); sys_umul #(12,12) mul(CLK_VIDEO,mul_start,mul_run, mul_arg1,mul_arg2,mul_res);
wire [11:0] wideres = mul_res[11:0] + hsize;
always @(posedge CLK_VIDEO) begin always @(posedge CLK_VIDEO) begin
reg [11:0] oheight,htarget,wres; reg [11:0] oheight,htarget,wres,hinteger,wideres;
reg [12:0] arxf,aryf; reg [12:0] arxf,aryf;
reg [3:0] cnt; reg [3:0] cnt;
reg narrow; reg narrow;
@@ -264,7 +262,8 @@ always @(posedge CLK_VIDEO) begin
// [3] 1080 / 512 * 512 * 4 / 3 / 512 * 512 -> 1024 // [3] 1080 / 512 * 512 * 4 / 3 / 512 * 512 -> 1024
7: if(mul_res <= HDMI_WIDTH) begin 7: if(mul_res <= HDMI_WIDTH) begin
cnt <= 10; hinteger = mul_res[11:0];
cnt <= 12;
end end
8: begin 8: begin
@@ -286,8 +285,20 @@ always @(posedge CLK_VIDEO) begin
// [3] 1920 / 512 * 512 -> 1536 // [3] 1920 / 512 * 512 -> 1536
10: begin 10: begin
narrow <= ((htarget - mul_res[11:0]) <= (wideres - htarget)) || (wideres > HDMI_WIDTH); hinteger <= mul_res[11:0];
wres <= mul_res[11:0] == htarget ? mul_res[11:0] : wideres; mul_arg1 <= vsize;
mul_arg2 <= div_res[11:0] ? div_res[11:0] : 12'd1;
mul_start <= 1;
end
11: begin
oheight <= mul_res[11:0];
end
12: begin
wideres <= hinteger + hsize;
narrow <= ((htarget - hinteger) <= (wideres - htarget)) || (wideres > HDMI_WIDTH);
wres <= hinteger == htarget ? hinteger : wideres;
end end
// [1] 1066 - 720 = 346 <= 1440 - 1066 = 374 || 1440 > 1920 -> true // [1] 1066 - 720 = 346 <= 1440 - 1066 = 374 || 1440 > 1920 -> true
// [2] 1280 - 1280 = 0 <= 1920 - 1280 = 640 || 1920 > 1920 -> true // [2] 1280 - 1280 = 0 <= 1920 - 1280 = 640 || 1920 > 1920 -> true
@@ -299,11 +310,11 @@ always @(posedge CLK_VIDEO) begin
// to target width, meaning it is not optimal for source aspect ratio. // to target width, meaning it is not optimal for source aspect ratio.
// otherwise it is set to narrow width that is optimal. // otherwise it is set to narrow width that is optimal.
11: begin 13: begin
case(SCALE) case(SCALE)
2: arxf <= {1'b1, mul_res[11:0]}; 2: arxf <= {1'b1, hinteger};
3: arxf <= {1'b1, (wres > HDMI_WIDTH) ? mul_res[11:0] : wres}; 3: arxf <= {1'b1, (wres > HDMI_WIDTH) ? hinteger : wres};
4: arxf <= {1'b1, narrow ? mul_res[11:0] : wres}; 4: arxf <= {1'b1, narrow ? hinteger : wres};
default: arxf <= {1'b1, div_num[11:0]}; default: arxf <= {1'b1, div_num[11:0]};
endcase endcase
aryf <= {1'b1, oheight}; aryf <= {1'b1, oheight};
+9 -6
View File
@@ -36,13 +36,15 @@ module yc_out
input hsync, input hsync,
input vsync, input vsync,
input csync, input csync,
input de,
input [23:0] din, input [23:0] din,
output [23:0] dout, output [23:0] dout,
output reg hsync_o, output reg hsync_o,
output reg vsync_o, output reg vsync_o,
output reg csync_o output reg csync_o,
output reg de_o
); );
wire [7:0] red = din[23:16]; wire [7:0] red = din[23:16];
@@ -61,6 +63,7 @@ typedef struct {
logic hsync; logic hsync;
logic vsync; logic vsync;
logic csync; logic csync;
logic de;
} phase_t; } phase_t;
localparam MAX_PHASES = 7'd8; localparam MAX_PHASES = 7'd8;
@@ -211,11 +214,11 @@ always_ff @(posedge clk) begin
end end
// Adjust sync timing correctly // Adjust sync timing correctly
phase[1].hsync <= hsync; phase[1].vsync <= vsync; phase[1].csync <= csync; phase[1].hsync <= hsync; phase[1].vsync <= vsync; phase[1].csync <= csync; phase[1].de <= de;
phase[2].hsync <= phase[1].hsync; phase[2].vsync <= phase[1].vsync; phase[2].csync <= phase[1].csync; phase[2].hsync <= phase[1].hsync; phase[2].vsync <= phase[1].vsync; phase[2].csync <= phase[1].csync; phase[2].de <= phase[1].de;
phase[3].hsync <= phase[2].hsync; phase[3].vsync <= phase[2].vsync; phase[3].csync <= phase[2].csync; phase[3].hsync <= phase[2].hsync; phase[3].vsync <= phase[2].vsync; phase[3].csync <= phase[2].csync; phase[3].de <= phase[2].de;
phase[4].hsync <= phase[3].hsync; phase[4].vsync <= phase[3].vsync; phase[4].csync <= phase[3].csync; phase[4].hsync <= phase[3].hsync; phase[4].vsync <= phase[3].vsync; phase[4].csync <= phase[3].csync; phase[4].de <= phase[3].de;
hsync_o <= phase[4].hsync; vsync_o <= phase[4].vsync; csync_o <= phase[4].csync; hsync_o <= phase[4].hsync; vsync_o <= phase[4].vsync; csync_o <= phase[4].csync; de_o <= phase[4].de;
phase[1].y <= phase[0].y; phase[2].y <= phase[1].y; phase[3].y <= phase[2].y; phase[4].y <= phase[3].y; phase[5].y <= phase[4].y; phase[1].y <= phase[0].y; phase[2].y <= phase[1].y; phase[3].y <= phase[2].y; phase[4].y <= phase[3].y; phase[5].y <= phase[4].y;
+12
View File
@@ -0,0 +1,12 @@
*.vcd
/dw_boot*
/fujinet_boot*/
fujinet_boot/
imgui.ini
obj_dir/
roms/**/*.rom
screenshot_*.png
test-out*/
test-out/
tests/hello.dsk
trace*.txt
+157
View File
@@ -0,0 +1,157 @@
#============================================================================
# CoCo3 Verilator simulation
#
# Same layout as the FM-7 and Apple-IIgs sims: sim.v stands in for CoCo3.sv,
# sim/ is the shared ImGui/SDL framework, and one binary runs either windowed
# or with --headless.
#
# make build ./obj_dir/Vemu
# make run build and launch the windowed sim
# make headless build and boot to BASIC headless, screenshot at the end
# make test build and run the headless smoke test (run_tests.sh)
# make lint elaborate the design only
# make mem regenerate rtl/*.mem from the VHDL/MIF sources
# make clean
#
# No ghdl step. The build uses the Verilog cycle-accurate 6809 (mc6809glb.v,
# selected by CoCo3_CYC_ACC_6809 in rtl/config.sv), and the VHDL entities it
# does instantiate -- ROMs, RAMs, the font -- are converted by hand in rtl/:
#
# rtl/rom/coco_rom_32K.vhd, coco_rom_8K.vhd, coco_rom_cart.vhd,
# coco_rom_16.vhd, coco3_char_rom.vhd -> rtl/coco_rom.v
# rtl/sram/coco_ram.vhd, coco_vid_ram_buf.vhd -> rtl/coco_sram.v
#
# Quartus-only pieces are replaced as well: rtl/VDAC.v (altsyncram) by
# rtl/VDAC.v here, rtl/sdram/sdram2.sv by rtl/sdram2.sv here (same controller,
# chip model instead of pins), and the PLL by clocks driven from sim_main.
#============================================================================
V = verilator
RTL = ../rtl
TOP = --top-module emu
# Verilator 5 demands --no-timing for the cosmetic `#` delays; 4.x rejects the
# flag. Same probe as the FM-7 Makefile.
VERILATOR_MAJOR := $(shell verilator --version 2>/dev/null | sed -n 's/^Verilator \([0-9][0-9]*\).*/\1/p')
NO_TIMING := $(if $(filter 4,$(VERILATOR_MAJOR)),,--no-timing)
# -Wno-PROCASSWIRE: coco3fpga.sv and fdc.sv declare a number of registers as
# `wire` and assign them in always blocks (Build_Info, VMA, PIX_CLK_D, the $FF40
# latch, ...). Quartus accepts that and so does Verilator once the check is
# waived; the RTL is left as it is.
V_DEFINE = +define+SIMULATION=1 -Wno-PROCASSWIRE \
--timescale-override 1ps/1ps -Wno-TIMESCALEMOD -Wno-fatal \
$(NO_TIMING) --converge-limit 6000 \
-I$(RTL)
# VCD tracing: `make clean && make TRACE=1`, then run with --vcd <file> and a
# --trace-from/--trace-until window (a 114 MHz design dumps ~1 GB a frame).
ifeq ($(TRACE),1)
V_DEFINE += --trace
CXX_DEFINE += -DVM_TRACE_VCD=1
else
CXX_DEFINE += -DVM_TRACE_VCD=0
endif
UNAME_S := $(shell uname -s)
ifeq ($(UNAME_S), Darwin)
LIBS += -framework OpenGL -framework Cocoa -framework IOKit -framework CoreVideo `sdl2-config --libs`
LIBS += -L/usr/local/lib -L/opt/local/lib -L/opt/homebrew/lib
CXXFLAGS += `sdl2-config --cflags`
CXXFLAGS += `sdl2-config --cflags | sed 's|include/SDL2|include/|'`
CXXFLAGS += -I/usr/local/include -I/opt/local/include -I/opt/homebrew/include
endif
ifeq ($(UNAME_S), Linux)
LIBS += -lGL -ldl `sdl2-config --libs`
CXXFLAGS += `sdl2-config --cflags`
endif
ifeq ($(findstring MINGW,$(UNAME_S)),MINGW)
LIBS += -lgdi32 -lopengl32 -limm32 `pkg-config --static --libs sdl2`
CXXFLAGS += `pkg-config --cflags sdl2`
endif
CC_OPT = -O2
V_OPT = -O3 --x-assign fast --x-initial fast --noassert
CXXFLAGS += $(CC_OPT) $(CXX_DEFINE) -I../sim/imgui -I../sim -I.. -g
LDFLAGS = $(LIBS)
EXE = ./obj_dir/Vemu
V_SRC = \
sim.vlt \
sim.v \
rtl/sdram2.sv \
rtl/coco_rom.v \
rtl/coco_sram.v \
rtl/VDAC.v \
rtl/ovo.v \
../sys/hps_io.sv \
$(RTL)/coco3fpga.sv \
$(RTL)/EE_Cold_Bt.v \
$(RTL)/cassette.v \
$(RTL)/square_gen.v \
$(RTL)/AMW.v \
$(RTL)/rtc.sv \
$(RTL)/fdc.sv \
$(RTL)/wd1793.sv \
$(RTL)/sdc.sv \
$(RTL)/sdc_top.sv \
$(RTL)/Auto_Run.sv \
$(RTL)/ps2_mouse.v \
$(RTL)/coco_mem_fetch.sv \
$(RTL)/Cassette_Write.sv \
$(RTL)/cocokey.v \
$(RTL)/PS2_Key/ps2_keyboard.v \
$(RTL)/UART_6551/uart_6551.v \
$(RTL)/UART_6551/6551tx.v \
$(RTL)/UART_6551/6551rx.v \
$(RTL)/mc6809glb/mc6809glb.v \
$(RTL)/Mister_Video.v
C_SRC = \
sim_main.cpp dis6809.cpp serial.cpp \
sim/sim_bus.cpp sim/sim_clock.cpp sim/sim_console.cpp sim/sim_video.cpp \
sim/sim_blkdevice.cpp sim/sim_input.cpp sim/sim_audio.cpp \
sim/imgui/imgui_impl_sdl.cpp sim/imgui/imgui_impl_opengl2.cpp \
sim/imgui/imgui_draw.cpp sim/imgui/imgui_widgets.cpp sim/imgui/imgui_tables.cpp \
sim/imgui/imgui.cpp sim/imgui/ImGuiFileDialog.cpp \
sim/imgui/implot.cpp sim/imgui/implot_items.cpp
VOUT = obj_dir/Vemu.cpp
all: $(EXE)
$(VOUT): $(V_SRC) Makefile
$V -cc $(V_OPT) -LDFLAGS "$(LDFLAGS)" -exe --Mdir ./obj_dir \
$(V_DEFINE) $(TOP) -CFLAGS "$(CXXFLAGS)" $(V_SRC) $(C_SRC)
$(EXE): $(VOUT) $(C_SRC) sim/*.h dis6809.h serial.h
(cd obj_dir; $(MAKE) -f Vemu.mk OBJCACHE= OPT_FAST="-O2" OPT_SLOW="-O0" OPT_GLOBAL="-O2")
lint:
$V --lint-only $(V_DEFINE) -Wno-WIDTH $(TOP) $(V_SRC)
mem:
python3 gen_mem.py
run: all
$(EXE)
headless: all
$(EXE) --headless --stop-at-frame 150 --screenshot 150
test: all
./run_tests.sh
clean:
rm -rf obj_dir
.PHONY: all lint mem run headless test clean
# Disassembler self-check. Standalone -- no Verilator, no core.
distest: dis6809_test.cpp dis6809.cpp dis6809.h
mkdir -p obj_dir && c++ -O1 -o obj_dir/distest dis6809_test.cpp dis6809.cpp -I. && ./obj_dir/distest
.PHONY: distest
+288
View File
@@ -0,0 +1,288 @@
# CoCo3 Verilator simulation
Runs the core on the host, windowed (ImGui + SDL2) or headless, so you can boot
it, type at it, mount disks, screenshot it and trace the 6809, without a
DE10-Nano or a Quartus build.
It uses the same framework as the FM-7 and Apple-IIgs sims: `sim.v` stands in
for `CoCo3.sv`, `sim/` is the shared ImGui/SDL harness (`sim_bus`, `sim_video`,
`sim_input`, `sim_blkdevice`, ...), and one binary does both modes.
## Build and run
```sh
cd verilator
make # -> ./obj_dir/Vemu
make run # windowed
make headless # boot headless to frame 150, screenshot
make test # headless smoke tests (run_tests.sh)
make lint # elaborate only
```
Needs Verilator 5 (built and tested with 5.044), SDL2, and Python 3 for the
generators (`brew install verilator sdl2`). **Run the binary from this
directory**: the ROM defaults and the `$readmemh` images under `rtl/` are
relative paths.
### ROMs
The core loads its ROMs over ioctl at start-up, the way Main_MiSTer does, so
the sim needs the same two files the MiSTer SD card has in `games/CoCo3/`:
| file | contents | ioctl index |
|---|---|---|
| `roms/boot0.rom` | CoCo 3 ROM (32K, `coco3.rom`) | 0 |
| `roms/boot1.rom` | Disk BASIC 1.1 (8K, `disk11.rom`) | 64 |
They are not in git (`roms/*.rom` is ignored). Copy them from your MiSTer, or
from ToolShed's `cocoroms/` build. `--rom` / `--disk-rom` point elsewhere.
## Headless
```sh
# Boot and print the text screen
./obj_dir/Vemu --headless --stop-at-frame 150 --ascii-end
# Type at BASIC; {RETURN} or \n for Enter, {BREAK}, {CLEAR}, {UP}...
./obj_dir/Vemu --headless --stop-at-frame 260 --type '140:PRINT 2+2\n' --ascii-end
# Floppy in drive 0 (selects MPI slot 4), load and run a program
./obj_dir/Vemu --headless --disk tests/hello.dsk --stop-at-frame 420 \
--type '140:RUN"HELLO\n' --screenshot 420
# Disassembly trace of frames 10-11
./obj_dir/Vemu --headless --stop-at-frame 11 --trace-cpu trace.txt --trace-from 10
```
`--help` lists everything: cartridge (`--cart`), cassette (`--cas`), CoCoSDC
(`--sdc`), memory size, turbo speed, artifact mode, `--frame-log` (per-frame
framebuffer hash + instruction count), `--trace-bus`, `--vcd`.
BASIC's banner appears around frame 130. Most of that is the core itself:
`coco3fpga.sv` holds `RESET_N` for 143 ms and `CPU_RESET` for 286 ms after
power-on, and the first frame only appears once the video timing leaves reset.
Type from frame 140 on.
`--ascii` prints the 32×16 VDG screen at `$0400` as the CPU last wrote it (from
a shadow of the CPU bus). That is what the tests judge. It does not follow
`WIDTH 40/80` or graphics modes; use a screenshot for those.
Typed keys are held 2 frames with a 2-frame gap, plus 30 frames after each
RETURN (`--key-hold`, `--key-gap`, `--return-gap`). The CoCo has no type-ahead:
while BASIC runs a line it does not scan the keyboard, so keys pressed then are
lost, on the real machine as well as here.
### Tests
`./run_tests.sh [name...]` runs these in parallel (about 8 minutes in all):
| test | does | judged on |
|---|---|---|
| `boot` | power on, wait for the banner | text screen: `DISK EXTENDED COLOR BASIC 2.1`, `OK` |
| `keyboard` | `PRINT 2+2` | text screen: ` 4` |
| `disk` | `RUN"HELLO` from `tests/hello.dsk` | text screen: `HELLO FROM DISK`, ` 42` |
| `width80` | `WIDTH 80`, then print | screenshot (GIME 80-column text) |
| `hscreen` | `HSCREEN 2`, `HCIRCLE`, `HLINE ... B` | screenshot (GIME 320x192 graphics) |
Every test's final screenshot is compared byte for byte with `test-ref/`. The
sim is deterministic, so a changed image means the RTL or harness changed what
is drawn. After an intended change, `BLESS=1 ./run_tests.sh` records new
references. Output goes to `test-out/`.
### Speed
About **1.2 simulated frames per second** (boot to BASIC ~125 s on an
Apple-silicon Mac), or ~1.6 fps with `--fast-clocks` (~77 s).
Where the time goes, and the two speed-ups made:
- The CoCo clocks are 114.5 MHz (SDRAM controller, the `data_ready` latch,
the video line fetcher), 57.3 MHz `clk_sys` (everything else: 48 negedge
and 10 posedge blocks), 14.3 MHz pixel clock, and CLK_50M for the RTC/UART.
CLK_28 is unused.
- `status` (the OSD word) used to be a top-level input. It feeds the video
pixel mux, so Verilator re-evaluated that mux on every eval, about 20% of the
run time. `sim.v` now registers it, as `hps_io` does on the FPGA.
- `--fast-clocks` steps per half-period of `clk_sys` and runs the 114 MHz
domain at 57 MHz, halving the evals. At normal CPU speeds an SDRAM access
still finishes well inside a CPU cycle. All five tests give byte-identical
screenshots and identical instruction counts either way
(`SIMARGS=--fast-clocks ./run_tests.sh`). High turbo speeds (6 `clk_sys`
per CPU cycle at 9.54 MHz) and video fetch bandwidth are where it could
differ; use the default when timing is the question.
## Serial (RS-232 Pak / FujiNet)
The core's only UART is the RS-232 Pak, a `glb6551` at `$FF68-$FF6B`; on
MiSTer its pins are the `UART_*` signals the FujiNet daemon reaches as
`/dev/ttyS1`. The sim works on those pins, not on the registers:
- **TXD is decoded** at whatever rate the 6551 is programmed for, and every
byte is printed: `SERIAL TX <frame> <hex> |ascii|`.
- **RXD is driven** from a pty (`--serial-pty`, name printed at start) or from
`--serial-send FRAME:HEX...`, at the far end's rate: `--serial-baud N`, or by
default the 6551's transmit rate.
- `--trace-acia` logs every CPU access to `$FF68-$FF6B`, and whether it
actually reached the chip. The exit summary counts bytes, accesses and
undecoded accesses, and warns on a receive-clock mismatch.
- The windowed build has a Serial window with the same information.
- `tests/dwserver.py PTY DISK...` is a minimal DriveWire 3 server (stdlib only)
to stand in for FujiNet: `READEX`, `WRITE`, `TIME`, `DWINIT`, ...
`tests/dw_boot.sh CART DISK STOP [sim args]` wires the two together:
```sh
tests/dw_boot.sh ../../FujiNet_MiSTer/roms/HDBDW3S3.CCC tests/hello.dsk 350 \
--type '140:RUN"HELLO\n'
```
That boots HDB-DOS over DriveWire (reads LSN 0 and the directory), then
`RUN"HELLO` loads and runs the program from the served image, about 5 minutes.
The sim runs ~50x slower than real time, so the far end sees roughly 400 baud
of real throughput whatever rate is programmed. A real FujiNet may time out
where `dwserver.py` does not.
### FujiNet on this core: what was wrong, and the fix
Tested with FujiNet_MiSTer's carts and the real FujiNet daemon (FujiNet-PC
built for `COCO`, run with FujiNet_MiSTer's `fnconfig.ini` pointed at the sim's
pty; `tests/fujinet_boot.sh`).
1. **The 6551 was unreachable with a cart in slot 3.** `coco3fpga.sv` decoded
`$FF68-$FF6B` only when the Multi-Pak I/O select was slot 1
(`MPI_SCS == 0`), and the OSD offers only slots 2-4. HDB-DOS programmed the
chip and polled status forever. It read `$AA` from an empty bus, stopped at
`HDB-DOS 1.5 SY6551 COCO 3`, and transmitted nothing. On a real CoCo the
SCS line covers only `$FF40-$FF5F`, and the RS-232 Pak decodes `$FF68` from
the address bus, so it works in any slot. **Fix:** `RS232_EN` no longer
looks at `MPI_SCS`. (Upstream's 20260927 release moved the decode to slots
2 and 4, `MPI_SCS[0] == 1`; HDB-DOS carts can only boot from slot 3, so
that still missed every access.)
2. **The 19,200 cart received at 115,200.** `HDBDW3L3_19200.CCC` writes
control `$0F`. Bit 4 = 0 selects the "external" receive clock, which
`uart_6551.v` tied to the 1.8475 MHz enable, i.e. 115,200 baud. The cart
transmitted at 19,200 and received garbage: FujiNet logged `Checksum error:
expected 65280, got 57344`. **Fix:** the receiver is clocked from the baud
generator (`RX_CLK = TX_CLK`). That is unchanged for control `$1x` and for
baud select 0.
3. **Slot 3 hung FujiNet's CONFIG loader.** Once a cart finished downloading
after boot, slot 3 toggled the CART interrupt every CPU cycle, forever. That
is right for a program pak (CART tied to Q autostarts it), but a disk-style
ROM such as HDB-DOS never drives CART. FujiNet's `CFGLOAD.BIN` re-enables
that interrupt and then hung in an endless FIRQ, after reading 17 sectors.
A reset cleared it, which is why "load cart, then Reset" worked. The OSD's
"Cart Interrupt Disabled" option was not connected to anything. **Fix:** a
cart that starts with `DK` gets a cold boot instead, the way BASIC starts
it at power-on, and the OSD option (Debug menu, `status[19]` ->
`SWITCH[9]`) now suppresses the autostart interrupt.
Program paks behave as before. The sim reproduces both cases with
`--cart-frame N`, which loads the cart after boot the way the OSD and MGL
do.
With these fixes, the L3 cart at 19,200 (the MiSTer configuration) boots from the
real FujiNet daemon with no checksum errors, and gets to FujiNet's CONFIG
splash. The S3 cart (115,200) reaches the CONFIG host-slots screen.
On the FPGA the rest of the path already works. `sys_top.v` wires the core's
`UART_*` pins straight to the HPS UART (`/dev/ttyS1`), whatever the OSD UART
mode. The 6551 only transmits while CTS is low, and CTS is the HPS UART's RTS.
FujiNet-PC turns off `CRTSCTS` and leaves RTS as Linux sets it on open
(asserted), so that holds while `start_fujinet.sh` has the port open.
**Sim-only caveat:** FujiNet times out reads after 500 ms of wall-clock time,
and the sim runs ~50x slower than real time. The CoCo cannot return a sector's
checksum in time, and FujiNet logs `got 65535`. These tests used a FujiNet
build with `.readTimeout(120000)` in `lib/bus/drivewire/drivewire.cpp`. On
hardware the stock value is fine.
## Windowed
`make run`. Windows: the video, a CPU/GIME inspector (registers, `$FF90`, a
live disassembly from the bus shadow), Control (run/pause/step, reset, cold
boot, screenshot, the OSD options, cart/cassette/floppy/SDC file dialogs) and a
console. Keys go to the CoCo from the host keyboard through the same PS/2 path
as on hardware.
## What is simulated, and what is replaced
`sim.v` wires the core the way `CoCo3.sv` does, including the OSD `status` word
decode, the joystick centring and the cassette RAM. The replacements:
| on MiSTer | here | why |
|---|---|---|
| PLL (114.545/57.27/28.64/14.32 MHz) | clocks from `sim_main.cpp` | all phase 0, exact /2 /4 /8, so they are derived from one counter and all rise in the same eval |
| `rtl/sdram/sdram2.sv` | `rtl/sdram2.sv` | same controller logic, plus a CAS-3, burst-2 SDR chip model in place of the `SDRAM_*` pins |
| `hps_io` keyboard | `sys/hps_io.sv`'s own `ps2_device` | `ps2_key` events are fed into the real PS/2 serializer at `PS2DIV(2400)`, so `cocokey.v` sees the same serial stream |
| `rtl/VDAC.v` (altsyncram) | `rtl/VDAC.v` | registered dual-port RAM, preloaded from `VDAC.mif` |
| VHDL ROM/RAM entities | `rtl/coco_rom.v`, `rtl/coco_sram.v` | Verilog conversions, see below |
### VHDL to Verilog
The build uses the Verilog cycle-accurate 6809 (`rtl/mc6809glb/mc6809glb.v`),
because `rtl/config.sv` defines `CoCo3_CYC_ACC_6809`. The VHDL CPU
(`rtl/CPU09/cpu09*.vhd`) is not instantiated, so nothing needs ghdl. The VHDL
the core does use was converted by hand, one module per entity with the same
names and ports:
| VHDL | Verilog |
|---|---|
| `rtl/rom/coco_rom_32K.vhd`, `coco_rom_8K.vhd`, `coco_rom_cart.vhd` | `rtl/coco_rom.v` (`COCO_ROM_32K`, `COCO_ROM_8K`, `COCO_ROM_CART`) |
| `rtl/rom/coco_rom_16.vhd` | `rtl/coco_rom.v` (`COCO_ROM_16`) |
| `rtl/rom/coco3_char_rom.vhd` | `rtl/coco_rom.v` (`coco3_Char_ROM`) + `rtl/coco3_char_rom.mem` |
| `rtl/sram/coco_ram.vhd`, `coco_vid_ram_buf.vhd` | `rtl/coco_sram.v` (`COCO_SRAM`, `COCO_VID_RAM_BUF`) |
| `rtl/OVO.vhd` (debug / "NO ROM" overlay) | `rtl/ovo.v` (`ovo`) |
`make mem` (`gen_mem.py`) regenerates `rtl/coco3_char_rom.mem` from the font
table in the VHDL and `rtl/vdac.mem` from `rtl/VDAC.mif`.
## Traps found while bringing it up
**Verilator re-runs block-local initialisers.** A variable declared with an
initialiser inside an `always` block, like `reg [4:0] state = STATE_STARTUP;` in
`sdram2.sv`, is re-initialised every time the block runs under Verilator 5.044.
It is not a one-time static. The SDRAM controller was pinned in
`STATE_STARTUP`, and the CPU stalled on its first RAM access. The sim copy
hoists those registers to module scope. Look for this in any other core
(`make lint` flags them as `IMPLICITSTATIC`).
**Quartus powers async-set registers up at 1.** A register with an asynchronous
set is built with NOT-gate push-back, so it starts at 1 on the FPGA and at 0
here. `mc6809x`'s `NMILatched` (active low) is one of them. At 0 the CPU took a
phantom NMI on its first instruction. `sim.v` sets it to 1 in an `initial`
block, which models the FPGA's power-up state.
**`// verilator ...` in a comment is a pragma.** A comment line that *starts*
with the word "verilator" is parsed as a directive and fails the build with
`BADVLTPRAGMA`.
**`rtl/wd1793.sv`:** `spt_addr` and `buff_wr` were declared inside `generate`
blocks but assigned outside them. Quartus accepts that. Verilator rejects
`spt_addr`, and silently makes `buff_wr` a separate implicit net, so the
sector-buffer write strobe would never reach the RAM. Both are now declared at
module scope. FM-7 made the same fix to its copy of the file. There is no
behavioural change on the FPGA.
The core also declares some registers as `wire` and assigns them in `always`
blocks (`Build_Info`, `VMA`, `PIX_CLK_D`, the `$FF40` latch in `fdc.sv`).
Quartus accepts it. The Makefile passes `-Wno-PROCASSWIRE` rather than editing
the RTL.
## Files
```
Makefile build, lint, test
sim.v emu top: CoCo3.sv without sys/, plus debug taps
sim_main.cpp clocks, options, headless loop, ImGui windows
serial.{cpp,h} 6551 line model: TXD decoder, RXD driver, pty bridge
sim.vlt Verilator config (forceable net for --acia-any-slot)
dis6809.{cpp,h} 6809 disassembler (shared with FM-7)
run_tests.sh smoke tests, judged on text screen + screenshot
gen_mem.py VHDL/MIF -> rtl/*.mem
rtl/ Verilog conversions and sim replacements
sim/ shared ImGui/SDL framework
tests/ make_test_disk.py -> hello.dsk (Disk BASIC image),
dwserver.py (minimal DriveWire 3 server)
test-ref/ blessed screenshots for run_tests.sh
```
+233
View File
@@ -0,0 +1,233 @@
//============================================================================
// Motorola 6809 disassembler
//
// Table-driven, covering pages 1 ($xx), 2 ($10 xx) and 3 ($11 xx), all six
// addressing modes and the full indexed postbyte set. No 6309 extensions --
// rtl/mc6809i.v is a 6809, and silently decoding 6309 opcodes would hide the
// fact that the CPU has run off into data.
//============================================================================
#include "dis6809.h"
#include <cstdio>
#include <cstring>
namespace {
enum Mode {
INH, // inherent
IMM8,
IMM16,
DIR,
EXT,
IDX,
REL8,
REL16,
RLIST_S, // PSHS/PULS postbyte
RLIST_U, // PSHU/PULU postbyte
REGPAIR, // TFR/EXG postbyte
ILL
};
struct Op { const char* name; Mode mode; };
// ---- page 1 ---------------------------------------------------------------
const Op page1[256] = {
/*00*/ {"NEG",DIR},{"?",ILL},{"?",ILL},{"COM",DIR},{"LSR",DIR},{"?",ILL},{"ROR",DIR},{"ASR",DIR},
/*08*/ {"LSL",DIR},{"ROL",DIR},{"DEC",DIR},{"?",ILL},{"INC",DIR},{"TST",DIR},{"JMP",DIR},{"CLR",DIR},
/*10*/ {"?",ILL},{"?",ILL},{"NOP",INH},{"SYNC",INH},{"?",ILL},{"?",ILL},{"LBRA",REL16},{"LBSR",REL16},
/*18*/ {"?",ILL},{"DAA",INH},{"ORCC",IMM8},{"?",ILL},{"ANDCC",IMM8},{"SEX",INH},{"EXG",REGPAIR},{"TFR",REGPAIR},
/*20*/ {"BRA",REL8},{"BRN",REL8},{"BHI",REL8},{"BLS",REL8},{"BCC",REL8},{"BCS",REL8},{"BNE",REL8},{"BEQ",REL8},
/*28*/ {"BVC",REL8},{"BVS",REL8},{"BPL",REL8},{"BMI",REL8},{"BGE",REL8},{"BLT",REL8},{"BGT",REL8},{"BLE",REL8},
/*30*/ {"LEAX",IDX},{"LEAY",IDX},{"LEAS",IDX},{"LEAU",IDX},{"PSHS",RLIST_S},{"PULS",RLIST_S},{"PSHU",RLIST_U},{"PULU",RLIST_U},
/*38*/ {"?",ILL},{"RTS",INH},{"ABX",INH},{"RTI",INH},{"CWAI",IMM8},{"MUL",INH},{"RESET",INH},{"SWI",INH},
/*40*/ {"NEGA",INH},{"?",ILL},{"?",ILL},{"COMA",INH},{"LSRA",INH},{"?",ILL},{"RORA",INH},{"ASRA",INH},
/*48*/ {"LSLA",INH},{"ROLA",INH},{"DECA",INH},{"?",ILL},{"INCA",INH},{"TSTA",INH},{"?",ILL},{"CLRA",INH},
/*50*/ {"NEGB",INH},{"?",ILL},{"?",ILL},{"COMB",INH},{"LSRB",INH},{"?",ILL},{"RORB",INH},{"ASRB",INH},
/*58*/ {"LSLB",INH},{"ROLB",INH},{"DECB",INH},{"?",ILL},{"INCB",INH},{"TSTB",INH},{"?",ILL},{"CLRB",INH},
/*60*/ {"NEG",IDX},{"?",ILL},{"?",ILL},{"COM",IDX},{"LSR",IDX},{"?",ILL},{"ROR",IDX},{"ASR",IDX},
/*68*/ {"LSL",IDX},{"ROL",IDX},{"DEC",IDX},{"?",ILL},{"INC",IDX},{"TST",IDX},{"JMP",IDX},{"CLR",IDX},
/*70*/ {"NEG",EXT},{"?",ILL},{"?",ILL},{"COM",EXT},{"LSR",EXT},{"?",ILL},{"ROR",EXT},{"ASR",EXT},
/*78*/ {"LSL",EXT},{"ROL",EXT},{"DEC",EXT},{"?",ILL},{"INC",EXT},{"TST",EXT},{"JMP",EXT},{"CLR",EXT},
/*80*/ {"SUBA",IMM8},{"CMPA",IMM8},{"SBCA",IMM8},{"SUBD",IMM16},{"ANDA",IMM8},{"BITA",IMM8},{"LDA",IMM8},{"?",ILL},
/*88*/ {"EORA",IMM8},{"ADCA",IMM8},{"ORA",IMM8},{"ADDA",IMM8},{"CMPX",IMM16},{"BSR",REL8},{"LDX",IMM16},{"?",ILL},
/*90*/ {"SUBA",DIR},{"CMPA",DIR},{"SBCA",DIR},{"SUBD",DIR},{"ANDA",DIR},{"BITA",DIR},{"LDA",DIR},{"STA",DIR},
/*98*/ {"EORA",DIR},{"ADCA",DIR},{"ORA",DIR},{"ADDA",DIR},{"CMPX",DIR},{"JSR",DIR},{"LDX",DIR},{"STX",DIR},
/*A0*/ {"SUBA",IDX},{"CMPA",IDX},{"SBCA",IDX},{"SUBD",IDX},{"ANDA",IDX},{"BITA",IDX},{"LDA",IDX},{"STA",IDX},
/*A8*/ {"EORA",IDX},{"ADCA",IDX},{"ORA",IDX},{"ADDA",IDX},{"CMPX",IDX},{"JSR",IDX},{"LDX",IDX},{"STX",IDX},
/*B0*/ {"SUBA",EXT},{"CMPA",EXT},{"SBCA",EXT},{"SUBD",EXT},{"ANDA",EXT},{"BITA",EXT},{"LDA",EXT},{"STA",EXT},
/*B8*/ {"EORA",EXT},{"ADCA",EXT},{"ORA",EXT},{"ADDA",EXT},{"CMPX",EXT},{"JSR",EXT},{"LDX",EXT},{"STX",EXT},
/*C0*/ {"SUBB",IMM8},{"CMPB",IMM8},{"SBCB",IMM8},{"ADDD",IMM16},{"ANDB",IMM8},{"BITB",IMM8},{"LDB",IMM8},{"?",ILL},
/*C8*/ {"EORB",IMM8},{"ADCB",IMM8},{"ORB",IMM8},{"ADDB",IMM8},{"LDD",IMM16},{"?",ILL},{"LDU",IMM16},{"?",ILL},
/*D0*/ {"SUBB",DIR},{"CMPB",DIR},{"SBCB",DIR},{"ADDD",DIR},{"ANDB",DIR},{"BITB",DIR},{"LDB",DIR},{"STB",DIR},
/*D8*/ {"EORB",DIR},{"ADCB",DIR},{"ORB",DIR},{"ADDB",DIR},{"LDD",DIR},{"STD",DIR},{"LDU",DIR},{"STU",DIR},
/*E0*/ {"SUBB",IDX},{"CMPB",IDX},{"SBCB",IDX},{"ADDD",IDX},{"ANDB",IDX},{"BITB",IDX},{"LDB",IDX},{"STB",IDX},
/*E8*/ {"EORB",IDX},{"ADCB",IDX},{"ORB",IDX},{"ADDB",IDX},{"LDD",IDX},{"STD",IDX},{"LDU",IDX},{"STU",IDX},
/*F0*/ {"SUBB",EXT},{"CMPB",EXT},{"SBCB",EXT},{"ADDD",EXT},{"ANDB",EXT},{"BITB",EXT},{"LDB",EXT},{"STB",EXT},
/*F8*/ {"EORB",EXT},{"ADCB",EXT},{"ORB",EXT},{"ADDB",EXT},{"LDD",EXT},{"STD",EXT},{"LDU",EXT},{"STU",EXT},
};
// ---- page 2 ($10 prefix) --------------------------------------------------
Op page2_lookup(uint8_t op) {
switch (op) {
case 0x21: return {"LBRN",REL16}; case 0x22: return {"LBHI",REL16};
case 0x23: return {"LBLS",REL16}; case 0x24: return {"LBCC",REL16};
case 0x25: return {"LBCS",REL16}; case 0x26: return {"LBNE",REL16};
case 0x27: return {"LBEQ",REL16}; case 0x28: return {"LBVC",REL16};
case 0x29: return {"LBVS",REL16}; case 0x2a: return {"LBPL",REL16};
case 0x2b: return {"LBMI",REL16}; case 0x2c: return {"LBGE",REL16};
case 0x2d: return {"LBLT",REL16}; case 0x2e: return {"LBGT",REL16};
case 0x2f: return {"LBLE",REL16};
case 0x3f: return {"SWI2",INH};
case 0x83: return {"CMPD",IMM16}; case 0x8c: return {"CMPY",IMM16};
case 0x8e: return {"LDY",IMM16};
case 0x93: return {"CMPD",DIR}; case 0x9c: return {"CMPY",DIR};
case 0x9e: return {"LDY",DIR}; case 0x9f: return {"STY",DIR};
case 0xa3: return {"CMPD",IDX}; case 0xac: return {"CMPY",IDX};
case 0xae: return {"LDY",IDX}; case 0xaf: return {"STY",IDX};
case 0xb3: return {"CMPD",EXT}; case 0xbc: return {"CMPY",EXT};
case 0xbe: return {"LDY",EXT}; case 0xbf: return {"STY",EXT};
case 0xce: return {"LDS",IMM16};
case 0xde: return {"LDS",DIR}; case 0xdf: return {"STS",DIR};
case 0xee: return {"LDS",IDX}; case 0xef: return {"STS",IDX};
case 0xfe: return {"LDS",EXT}; case 0xff: return {"STS",EXT};
default: return {"?",ILL};
}
}
// ---- page 3 ($11 prefix) --------------------------------------------------
Op page3_lookup(uint8_t op) {
switch (op) {
case 0x3f: return {"SWI3",INH};
case 0x83: return {"CMPU",IMM16}; case 0x8c: return {"CMPS",IMM16};
case 0x93: return {"CMPU",DIR}; case 0x9c: return {"CMPS",DIR};
case 0xa3: return {"CMPU",IDX}; case 0xac: return {"CMPS",IDX};
case 0xb3: return {"CMPU",EXT}; case 0xbc: return {"CMPS",EXT};
default: return {"?",ILL};
}
}
const char* const IDX_REG[4] = { "X", "Y", "U", "S" };
// TFR/EXG register field. 6809 leaves 6,7 and 12..15 undefined.
const char* const TFR_REG[16] = {
"D","X","Y","U","S","PC","?6","?7","A","B","CC","DP","?c","?d","?e","?f"
};
void reg_list(uint8_t pb, bool is_u, char* out, size_t n) {
static const char* names_s[8] = {"CC","A","B","DP","X","Y","U","PC"};
static const char* names_u[8] = {"CC","A","B","DP","X","Y","S","PC"};
const char* const* names = is_u ? names_u : names_s;
out[0] = 0;
size_t len = 0;
for (int i = 0; i < 8; i++) {
if (!(pb & (1 << i))) continue;
int w = snprintf(out + len, n - len, "%s%s", len ? "," : "", names[i]);
if (w < 0 || (size_t)w >= n - len) break;
len += w;
}
if (!len) snprintf(out, n, "#$%02x", pb);
}
} // namespace
void cc6809_string(uint8_t cc, char out[9]) {
static const char* bits = "EFHINZVC"; // bit 7 .. bit 0
for (int i = 0; i < 8; i++) {
char c = bits[i];
out[i] = (cc & (0x80 >> i)) ? c : (char)(c + 32);
}
out[8] = 0;
}
int dis6809(uint16_t pc, int (*rd)(uint16_t), char* out, size_t outlen) {
// Local fetch helpers. `bad` sticks once any byte of the instruction is
// unknown, so the caller sees "??" rather than a plausible-looking lie.
int len = 0;
bool bad = false;
auto fetch = [&](void) -> int {
int v = rd((uint16_t)(pc + len));
len++;
if (v < 0) { bad = true; return 0; }
return v;
};
int op = fetch();
Op o;
if (bad) { snprintf(out, outlen, "??"); return 1; }
if (op == 0x10) { int o2 = fetch(); o = bad ? Op{"?",ILL} : page2_lookup((uint8_t)o2); }
else if (op == 0x11) { int o2 = fetch(); o = bad ? Op{"?",ILL} : page3_lookup((uint8_t)o2); }
else o = page1[op];
if (o.mode == ILL) {
snprintf(out, outlen, "FCB $%02x", op);
return 1;
}
char arg[64] = "";
switch (o.mode) {
case INH:
break;
case IMM8: { int v = fetch(); snprintf(arg, sizeof(arg), "#$%02x", v); break; }
case IMM16: { int h = fetch(), l = fetch(); snprintf(arg, sizeof(arg), "#$%02x%02x", h, l); break; }
case DIR: { int v = fetch(); snprintf(arg, sizeof(arg), "<$%02x", v); break; }
case EXT: { int h = fetch(), l = fetch(); snprintf(arg, sizeof(arg), "$%02x%02x", h, l); break; }
case REL8: { int v = fetch();
uint16_t dst = (uint16_t)(pc + len + (int8_t)v);
snprintf(arg, sizeof(arg), "$%04x", dst); break; }
case REL16: { int h = fetch(), l = fetch();
uint16_t dst = (uint16_t)(pc + len + (int16_t)((h << 8) | l));
snprintf(arg, sizeof(arg), "$%04x", dst); break; }
case RLIST_S: { int pb = fetch(); reg_list((uint8_t)pb, false, arg, sizeof(arg)); break; }
case RLIST_U: { int pb = fetch(); reg_list((uint8_t)pb, true, arg, sizeof(arg)); break; }
case REGPAIR: { int pb = fetch();
snprintf(arg, sizeof(arg), "%s,%s", TFR_REG[(pb >> 4) & 15], TFR_REG[pb & 15]);
break; }
case IDX: {
int pb = fetch();
const char* r = IDX_REG[(pb >> 5) & 3];
if (!(pb & 0x80)) {
// 5-bit signed offset, no indirect form
int off = pb & 0x1f;
if (off & 0x10) off -= 0x20;
snprintf(arg, sizeof(arg), "%d,%s", off, r);
break;
}
bool ind = (pb & 0x10) != 0;
char body[48];
switch (pb & 0x0f) {
case 0x0: snprintf(body, sizeof(body), ",%s+", r); break;
case 0x1: snprintf(body, sizeof(body), ",%s++", r); break;
case 0x2: snprintf(body, sizeof(body), ",-%s", r); break;
case 0x3: snprintf(body, sizeof(body), ",--%s", r); break;
case 0x4: snprintf(body, sizeof(body), ",%s", r); break;
case 0x5: snprintf(body, sizeof(body), "B,%s", r); break;
case 0x6: snprintf(body, sizeof(body), "A,%s", r); break;
case 0x8: { int v = fetch(); snprintf(body, sizeof(body), "$%02x,%s", v, r); break; }
case 0x9: { int h = fetch(), l = fetch();
snprintf(body, sizeof(body), "$%02x%02x,%s", h, l, r); break; }
case 0xb: snprintf(body, sizeof(body), "D,%s", r); break;
case 0xc: { int v = fetch();
// PCR offsets are relative to the byte after the instruction,
// which is only known once the whole thing is decoded -- so
// print the raw offset and let the target be inferred.
snprintf(body, sizeof(body), "$%02x,PCR", v); break; }
case 0xd: { int h = fetch(), l = fetch();
snprintf(body, sizeof(body), "$%02x%02x,PCR", h, l); break; }
case 0xf: { int h = fetch(), l = fetch();
snprintf(body, sizeof(body), "$%02x%02x", h, l); break; }
default: snprintf(body, sizeof(body), "?pb$%02x,%s", pb, r); break;
}
if (ind) snprintf(arg, sizeof(arg), "[%s]", body);
else snprintf(arg, sizeof(arg), "%s", body);
break;
}
default: break;
}
if (bad) snprintf(out, outlen, "%-5s ??", o.name);
else if (arg[0]) snprintf(out, outlen, "%-5s %s", o.name, arg);
else snprintf(out, outlen, "%s", o.name);
return len ? len : 1;
}
+18
View File
@@ -0,0 +1,18 @@
#pragma once
#include <cstdint>
#include <cstddef>
// Motorola 6809 disassembler.
//
// `read_byte` returns 0..255, or -1 for an address whose contents are not
// known. The sim feeds it a shadow of every byte the CPU has actually put on
// the bus, so unknown means "the CPU never fetched or wrote this" -- which is
// itself informative, and prints as "??".
//
// Returns the instruction length in bytes (1..5), and writes the mnemonic and
// operand to `out`. On an unknown opcode it emits "FCB $xx" and returns 1, so a
// caller walking a byte stream always makes progress.
int dis6809(uint16_t pc, int (*read_byte)(uint16_t), char* out, size_t outlen);
// Human-readable CC, e.g. "EFHINZVC" with cleared flags lower-cased.
void cc6809_string(uint8_t cc, char out[9]);
+63
View File
@@ -0,0 +1,63 @@
//============================================================================
// dis6809 self-check. `make distest`
//
// Covers every addressing mode, both prefix pages, the register-list and
// register-pair postbytes, and an undefined opcode. Cheap insurance: a
// disassembler that is subtly wrong is worse than none, because it produces
// confident output you will act on.
//============================================================================
#include "dis6809.h"
#include <cstdio>
#include <cstring>
static unsigned char M[0x10000];
static int rd(uint16_t a){ return M[a]; }
struct T { const char* bytes; const char* want; };
static int put(uint16_t a, const char* hex){ int n=0; while(*hex){ unsigned v; sscanf(hex,"%2x",&v); M[a+n++]=v; hex+=2; if(*hex==' ')hex++; } return n; }
int main(){
T t[] = {
{"20 09", "BRA $100b"},
{"16 01 23", "LBRA $1126"},
{"86 fd", "LDA #$fd"},
{"10 ce fc 7f", "LDS #$fc7f"},
{"1f 8b", "TFR A,DP"},
{"1e 12", "EXG X,Y"},
{"34 76", "PSHS A,B,X,Y,U"},
{"35 ff", "PULS CC,A,B,DP,X,Y,U,PC"},
{"36 40", "PSHU S"},
{"d6 04", "LDB <$04"},
{"be fb fe", "LDX $fbfe"},
{"6e 84", "JMP ,X"},
{"a6 80", "LDA ,X+"},
{"a6 81", "LDA ,X++"},
{"a6 82", "LDA ,-X"},
{"a6 83", "LDA ,--X"},
{"a6 91", "LDA [,X++]"},
{"a6 a5", "LDA B,Y"},
{"a6 c6", "LDA A,U"},
{"a6 88 7f", "LDA $7f,X"},
{"a6 89 12 34", "LDA $1234,X"},
{"a6 9f 20 00", "LDA [$2000]"},
{"a6 8c 10", "LDA $10,PCR"},
{"a6 1f", "LDA -1,X"},
{"a6 05", "LDA 5,X"},
{"e7 41", "STB 1,U"},
{"10 8e 12 34", "LDY #$1234"},
{"11 83 00 01", "CMPU #$0001"},
{"11 3f", "SWI3"},
{"39", "RTS"},
{"3d", "MUL"},
{"87", "FCB $87"},
};
int fail=0;
for (auto& e : t) {
memset(M,0,sizeof(M));
int n = put(0x1000, e.bytes);
char out[80];
int len = dis6809(0x1000, rd, out, sizeof(out));
bool ok = !strcmp(out, e.want) && (len==n || (!strcmp(e.want,"FCB $87")));
if(!ok){ printf("FAIL %-16s got \"%s\" (len %d, expected %d) want \"%s\"\n", e.bytes,out,len,n,e.want); fail++; }
}
printf(fail? "%d FAILURES\n" : "all %d cases pass\n", fail?fail:(int)(sizeof(t)/sizeof(t[0])));
return fail!=0;
}
+44
View File
@@ -0,0 +1,44 @@
#!/usr/bin/env python3
"""Regenerate the $readmemh images the Verilog conversions load.
rtl/rom/coco3_char_rom.vhd -> verilator/rtl/coco3_char_rom.mem (4096 x 8)
rtl/VDAC.mif -> verilator/rtl/vdac.mem ( 256 x 16)
Run from the verilator/ directory after either source changes.
"""
import re, sys
def char_rom():
src = open('../rtl/rom/coco3_char_rom.vhd').read()
body = src[src.index('signal RAM'):src.index(');', src.index('signal RAM'))]
vals = re.findall(r'x"([0-9A-Fa-f]{2})"', body)
if len(vals) != 4096:
sys.exit(f'coco3_char_rom.vhd: expected 4096 bytes, found {len(vals)}')
with open('rtl/coco3_char_rom.mem', 'w') as f:
for i in range(0, 4096, 16):
f.write(' '.join(v.upper() for v in vals[i:i+16]) + '\n')
def vdac():
mem = [0] * 256
txt = open('../rtl/VDAC.mif').read()
txt = txt[txt.index('CONTENT BEGIN') + len('CONTENT BEGIN'):txt.index('END;')]
for line in txt.splitlines():
line = line.split('--')[0].strip().rstrip(';')
if ':' not in line:
continue
addr, data = (s.strip() for s in line.split(':', 1))
words = data.split()
if addr.startswith('['): # [lo..hi] : value
lo, hi = (int(x, 16) for x in addr[1:-1].split('..'))
for a in range(lo, hi + 1):
mem[a] = int(words[0], 16)
else:
base = int(addr, 16)
for i, w in enumerate(words):
mem[base + i] = int(w, 16)
with open('rtl/vdac.mem', 'w') as f:
for i in range(0, 256, 8):
f.write(' '.join(f'{v:04X}' for v in mem[i:i+8]) + '\n')
char_rom()
vdac()
+27
View File
@@ -0,0 +1,27 @@
//============================================================================
// Simulation stand-in for rtl/VDAC.v (an altsyncram megafunction).
//
// Same ports and the configuration the megafunction declares: DUAL_PORT,
// 256 x 16, write on wrclock, address AND output registered on rdclock
// (address_reg_b = outdata_reg_b = CLOCK1), so q lags rdaddress by two
// rdclock edges. Preloaded from rtl/VDAC.mif via verilator/rtl/vdac.mem.
//============================================================================
module VDAC
(
input [15:0] data,
input [7:0] rdaddress,
input rdclock,
input [7:0] wraddress,
input wrclock,
input wren,
output reg [15:0] q
);
reg [15:0] mem [0:255];
reg [7:0] rd_a;
initial $readmemh("rtl/vdac.mem", mem);
always @(posedge wrclock) if (wren) mem[wraddress] <= data;
always @(posedge rdclock) begin
rd_a <= rdaddress;
q <= mem[rd_a];
end
endmodule
+256
View File
@@ -0,0 +1,256 @@
1C 22 20 20 20 22 1C 08 00 00 00 00 00 00 00 00
22 00 22 22 22 26 1A 00 00 00 00 00 00 00 00 00
04 08 1C 22 3E 20 1C 00 00 00 00 00 00 00 00 00
08 14 1C 02 1E 22 1E 00 00 00 00 00 00 00 00 00
14 00 1C 02 1E 22 1E 00 00 00 00 00 00 00 00 00
10 08 1C 02 1E 22 1E 00 00 00 00 00 00 00 00 00
08 00 1C 02 1E 22 1E 00 00 00 00 00 00 00 00 00
00 00 1C 22 20 22 1C 08 00 00 00 00 00 00 00 00
08 14 1C 22 3E 20 1C 00 00 00 00 00 00 00 00 00
14 00 1C 22 3E 20 1C 00 00 00 00 00 00 00 00 00
10 08 1C 22 3E 20 1C 00 00 00 00 00 00 00 00 00
14 00 18 08 08 08 1C 00 00 00 00 00 00 00 00 00
08 14 00 18 08 08 1C 00 00 00 00 00 00 00 00 00
00 0C 12 1C 12 12 1C 20 00 00 00 00 00 00 00 00
22 08 14 22 3E 22 22 00 00 00 00 00 00 00 00 00
08 08 14 22 3E 22 22 00 00 00 00 00 00 00 00 00
04 08 1C 22 22 22 1C 00 00 00 00 00 00 00 00 00
00 00 34 0A 1E 28 1E 00 00 00 00 00 00 00 00 00
1E 28 28 3C 28 28 2C 00 00 00 00 00 00 00 00 00
08 14 1C 22 22 22 1C 00 00 00 00 00 00 00 00 00
14 00 1C 22 22 22 1C 00 00 00 00 00 00 00 00 00
00 00 1C 26 2E 32 1C 00 00 00 00 00 00 00 00 00
08 14 00 22 22 26 1A 00 00 00 00 00 00 00 00 00
10 08 22 22 22 26 1A 00 00 00 00 00 00 00 00 00
1C 26 2A 2A 2A 32 1C 00 00 00 00 00 00 00 00 00
22 1C 22 22 22 22 1C 00 00 00 00 00 00 00 00 00
14 22 22 22 22 22 1C 00 00 00 00 00 00 00 00 00
1C 20 1C 22 1C 02 1C 00 00 00 00 00 00 00 00 00
04 0A 08 1C 08 0A 3C 00 00 00 00 00 00 00 00 00
08 08 3E 08 08 00 3E 00 00 00 00 00 00 00 00 00
04 0A 04 00 00 00 00 00 00 00 00 00 00 00 00 00
04 0A 08 1C 08 08 28 10 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
08 08 08 08 08 00 08 00 00 00 00 00 00 00 00 00
14 14 14 00 00 00 00 00 00 00 00 00 00 00 00 00
14 14 3E 14 3E 14 14 00 00 00 00 00 00 00 00 00
08 1E 28 1C 0A 3C 08 00 00 00 00 00 00 00 00 00
32 32 04 08 10 26 26 00 00 00 00 00 00 00 00 00
10 28 28 10 2A 24 1A 00 00 00 00 00 00 00 00 00
08 08 10 00 00 00 00 00 00 00 00 00 00 00 00 00
08 10 20 20 20 10 08 00 00 00 00 00 00 00 00 00
08 04 02 02 02 04 08 00 00 00 00 00 00 00 00 00
00 08 2A 1C 1C 2A 08 00 00 00 00 00 00 00 00 00
00 08 08 3E 08 08 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 08 08 10 00 00 00 00 00 00 00 00
00 00 00 3E 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 08 00 00 00 00 00 00 00 00 00
00 02 04 08 10 20 00 00 00 00 00 00 00 00 00 00
1C 22 26 2A 32 22 1C 00 00 00 00 00 00 00 00 00
08 18 08 08 08 08 1C 00 00 00 00 00 00 00 00 00
1C 22 02 1C 20 20 3E 00 00 00 00 00 00 00 00 00
1C 22 02 04 02 22 1C 00 00 00 00 00 00 00 00 00
04 0C 14 24 3E 04 04 00 00 00 00 00 00 00 00 00
3E 20 3C 02 02 02 3C 00 00 00 00 00 00 00 00 00
1C 20 20 3C 22 22 1C 00 00 00 00 00 00 00 00 00
3E 02 04 08 10 20 20 00 00 00 00 00 00 00 00 00
1C 22 22 1C 22 22 1C 00 00 00 00 00 00 00 00 00
1C 22 22 1E 02 02 1C 00 00 00 00 00 00 00 00 00
00 00 08 00 00 08 00 00 00 00 00 00 00 00 00 00
00 00 08 00 00 08 08 10 00 00 00 00 00 00 00 00
04 08 10 20 10 08 04 00 00 00 00 00 00 00 00 00
00 00 3E 00 3E 00 00 00 00 00 00 00 00 00 00 00
10 08 04 02 04 08 10 00 00 00 00 00 00 00 00 00
1C 22 02 04 08 00 08 00 00 00 00 00 00 00 00 00
1C 22 02 1A 2A 2A 1C 00 00 00 00 00 00 00 00 00
08 14 22 22 3E 22 22 00 00 00 00 00 00 00 00 00
3C 12 12 1C 12 12 3C 00 00 00 00 00 00 00 00 00
1C 22 20 20 20 22 1C 00 00 00 00 00 00 00 00 00
3C 12 12 12 12 12 3C 00 00 00 00 00 00 00 00 00
3E 20 20 3C 20 20 3E 00 00 00 00 00 00 00 00 00
3E 20 20 3C 20 20 20 00 00 00 00 00 00 00 00 00
1E 20 20 26 22 22 1C 00 00 00 00 00 00 00 00 00
22 22 22 3E 22 22 22 00 00 00 00 00 00 00 00 00
1C 08 08 08 08 08 1C 00 00 00 00 00 00 00 00 00
02 02 02 02 22 22 1C 00 00 00 00 00 00 00 00 00
22 24 28 30 28 24 22 00 00 00 00 00 00 00 00 00
20 20 20 20 20 20 3E 00 00 00 00 00 00 00 00 00
22 36 2A 2A 22 22 22 00 00 00 00 00 00 00 00 00
22 32 2A 26 22 22 22 00 00 00 00 00 00 00 00 00
1C 22 22 22 22 22 1C 00 00 00 00 00 00 00 00 00
3C 22 22 3C 20 20 20 00 00 00 00 00 00 00 00 00
1C 22 22 22 2A 24 1A 00 00 00 00 00 00 00 00 00
3C 22 22 3C 28 24 22 00 00 00 00 00 00 00 00 00
1C 22 10 08 04 22 1C 00 00 00 00 00 00 00 00 00
3E 08 08 08 08 08 08 00 00 00 00 00 00 00 00 00
22 22 22 22 22 22 1C 00 00 00 00 00 00 00 00 00
22 22 22 14 14 08 08 00 00 00 00 00 00 00 00 00
22 22 22 2A 2A 36 22 00 00 00 00 00 00 00 00 00
22 22 14 08 14 22 22 00 00 00 00 00 00 00 00 00
22 22 14 08 08 08 08 00 00 00 00 00 00 00 00 00
3E 02 04 08 10 20 3E 00 00 00 00 00 00 00 00 00
38 20 20 20 20 20 38 00 00 00 00 00 00 00 00 00
20 20 10 08 04 02 02 00 00 00 00 00 00 00 00 00
0E 02 02 02 02 02 0E 00 00 00 00 00 00 00 00 00
08 1C 2A 08 08 08 08 00 00 00 00 00 00 00 00 00
00 08 10 3E 10 08 00 00 00 00 00 00 00 00 00 00
08 14 22 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 1C 02 1E 22 1E 00 00 00 00 00 00 00 00 00
20 20 2C 32 22 32 2C 00 00 00 00 00 00 00 00 00
00 00 1C 22 20 22 1C 00 00 00 00 00 00 00 00 00
02 02 1A 26 22 26 1A 00 00 00 00 00 00 00 00 00
00 00 1C 22 3E 20 1C 00 00 00 00 00 00 00 00 00
04 0A 08 1C 08 08 08 00 00 00 00 00 00 00 00 00
00 00 1A 26 26 1A 02 1C 00 00 00 00 00 00 00 00
20 20 2C 32 22 22 22 00 00 00 00 00 00 00 00 00
00 08 00 18 08 08 1C 00 00 00 00 00 00 00 00 00
00 02 00 02 02 02 22 1C 00 00 00 00 00 00 00 00
20 20 24 28 30 28 24 00 00 00 00 00 00 00 00 00
18 08 08 08 08 08 1C 00 00 00 00 00 00 00 00 00
00 00 14 2A 2A 2A 2A 00 00 00 00 00 00 00 00 00
00 00 2C 32 22 22 22 00 00 00 00 00 00 00 00 00
00 00 1C 22 22 22 1C 00 00 00 00 00 00 00 00 00
00 00 2C 32 32 2C 20 20 00 00 00 00 00 00 00 00
00 00 1A 26 26 1A 02 02 00 00 00 00 00 00 00 00
00 00 2C 32 20 20 20 00 00 00 00 00 00 00 00 00
00 00 1E 20 1C 02 3C 00 00 00 00 00 00 00 00 00
10 10 38 10 10 12 0C 00 00 00 00 00 00 00 00 00
00 00 22 22 22 26 1A 00 00 00 00 00 00 00 00 00
00 00 22 22 22 14 08 00 00 00 00 00 00 00 00 00
00 00 22 2A 2A 14 14 00 00 00 00 00 00 00 00 00
00 00 22 14 08 14 22 00 00 00 00 00 00 00 00 00
00 00 22 22 22 1E 02 1C 00 00 00 00 00 00 00 00
00 00 3E 04 08 10 3E 00 00 00 00 00 00 00 00 00
08 10 10 20 10 10 08 00 00 00 00 00 00 00 00 00
08 08 08 00 08 08 08 00 00 00 00 00 00 00 00 00
08 04 04 02 04 04 08 00 00 00 00 00 00 00 00 00
10 2A 04 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 3E 00 00 00 00 00 00 00 00 00
00 00 1C 22 20 20 20 22 1C 08 00 00 00 00 00 00
00 00 22 00 22 22 22 26 1A 00 00 00 00 00 00 00
00 00 04 08 1C 22 3E 20 1C 00 00 00 00 00 00 00
00 00 08 14 1C 02 1E 22 1E 00 00 00 00 00 00 00
00 00 14 00 1C 02 1E 22 1E 00 00 00 00 00 00 00
00 00 10 08 1C 02 1E 22 1E 00 00 00 00 00 00 00
00 00 08 00 1C 02 1E 22 1E 00 00 00 00 00 00 00
00 00 00 00 1C 22 20 22 1C 08 00 00 00 00 00 00
00 00 08 14 1C 22 3E 20 1C 00 00 00 00 00 00 00
00 00 14 00 1C 22 3E 20 1C 00 00 00 00 00 00 00
00 00 10 08 1C 22 3E 20 1C 00 00 00 00 00 00 00
00 00 14 00 18 08 08 08 1C 00 00 00 00 00 00 00
00 00 08 14 00 18 08 08 1C 00 00 00 00 00 00 00
00 00 00 0C 12 1C 12 12 1C 20 00 00 00 00 00 00
00 00 22 08 14 22 3E 22 22 00 00 00 00 00 00 00
00 00 08 08 14 22 3E 22 22 00 00 00 00 00 00 00
00 00 04 08 1C 22 22 22 1C 00 00 00 00 00 00 00
00 00 00 00 34 0A 1E 28 1E 00 00 00 00 00 00 00
00 00 1E 28 28 3C 28 28 2C 00 00 00 00 00 00 00
00 00 08 14 1C 22 22 22 1C 00 00 00 00 00 00 00
00 00 14 00 1C 22 22 22 1C 00 00 00 00 00 00 00
00 00 00 00 1C 26 2E 32 1C 00 00 00 00 00 00 00
00 00 08 14 00 22 22 26 1A 00 00 00 00 00 00 00
00 00 10 08 22 22 22 26 1A 00 00 00 00 00 00 00
00 00 1C 26 2A 2A 2A 32 1C 00 00 00 00 00 00 00
00 00 22 1C 22 22 22 22 1C 00 00 00 00 00 00 00
00 00 14 22 22 22 22 22 1C 00 00 00 00 00 00 00
00 00 1C 20 1C 22 1C 02 1C 00 00 00 00 00 00 00
00 00 04 0A 08 1C 08 0A 3C 00 00 00 00 00 00 00
00 00 08 08 3E 08 08 00 3E 00 00 00 00 00 00 00
00 00 04 0A 04 00 00 00 00 00 00 00 00 00 00 00
00 00 04 0A 08 1C 08 08 28 10 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 08 08 08 08 08 00 08 00 00 00 00 00 00 00
00 00 14 14 14 00 00 00 00 00 00 00 00 00 00 00
00 00 14 14 3E 14 3E 14 14 00 00 00 00 00 00 00
00 00 08 1E 28 1C 0A 3C 08 00 00 00 00 00 00 00
00 00 32 32 04 08 10 26 26 00 00 00 00 00 00 00
00 00 10 28 28 10 2A 24 1A 00 00 00 00 00 00 00
00 00 08 08 10 00 00 00 00 00 00 00 00 00 00 00
00 00 08 10 20 20 20 10 08 00 00 00 00 00 00 00
00 00 08 04 02 02 02 04 08 00 00 00 00 00 00 00
00 00 00 08 2A 1C 1C 2A 08 00 00 00 00 00 00 00
00 00 00 08 08 3E 08 08 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 08 08 10 00 00 00 00 00 00
00 00 00 00 00 3E 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 08 00 00 00 00 00 00 00
00 00 00 02 04 08 10 20 00 00 00 00 00 00 00 00
00 00 1C 22 26 2A 32 22 1C 00 00 00 00 00 00 00
00 00 08 18 08 08 08 08 1C 00 00 00 00 00 00 00
00 00 1C 22 02 1C 20 20 3E 00 00 00 00 00 00 00
00 00 1C 22 02 04 02 22 1C 00 00 00 00 00 00 00
00 00 04 0C 14 24 3E 04 04 00 00 00 00 00 00 00
00 00 3E 20 3C 02 02 02 3C 00 00 00 00 00 00 00
00 00 1C 20 20 3C 22 22 1C 00 00 00 00 00 00 00
00 00 3E 02 04 08 10 20 20 00 00 00 00 00 00 00
00 00 1C 22 22 1C 22 22 1C 00 00 00 00 00 00 00
00 00 1C 22 22 1E 02 02 1C 00 00 00 00 00 00 00
00 00 00 00 08 00 00 08 00 00 00 00 00 00 00 00
00 00 00 00 08 00 00 08 08 10 00 00 00 00 00 00
00 00 04 08 10 20 10 08 04 00 00 00 00 00 00 00
00 00 00 00 3E 00 3E 00 00 00 00 00 00 00 00 00
00 00 10 08 04 02 04 08 10 00 00 00 00 00 00 00
00 00 1C 22 02 04 08 00 08 00 00 00 00 00 00 00
00 00 1C 22 02 1A 2A 2A 1C 00 00 00 00 00 00 00
00 00 08 14 22 22 3E 22 22 00 00 00 00 00 00 00
00 00 3C 12 12 1C 12 12 3C 00 00 00 00 00 00 00
00 00 1C 22 20 20 20 22 1C 00 00 00 00 00 00 00
00 00 3C 12 12 12 12 12 3C 00 00 00 00 00 00 00
00 00 3E 20 20 3C 20 20 3E 00 00 00 00 00 00 00
00 00 3E 20 20 3C 20 20 20 00 00 00 00 00 00 00
00 00 1E 20 20 26 22 22 1C 00 00 00 00 00 00 00
00 00 22 22 22 3E 22 22 22 00 00 00 00 00 00 00
00 00 1C 08 08 08 08 08 1C 00 00 00 00 00 00 00
00 00 02 02 02 02 22 22 1C 00 00 00 00 00 00 00
00 00 22 24 28 30 28 24 22 00 00 00 00 00 00 00
00 00 20 20 20 20 20 20 3E 00 00 00 00 00 00 00
00 00 22 36 2A 2A 22 22 22 00 00 00 00 00 00 00
00 00 22 32 2A 26 22 22 22 00 00 00 00 00 00 00
00 00 1C 22 22 22 22 22 1C 00 00 00 00 00 00 00
00 00 3C 22 22 3C 20 20 20 00 00 00 00 00 00 00
00 00 1C 22 22 22 2A 24 1A 00 00 00 00 00 00 00
00 00 3C 22 22 3C 28 24 22 00 00 00 00 00 00 00
00 00 1C 22 10 08 04 22 1C 00 00 00 00 00 00 00
00 00 3E 08 08 08 08 08 08 00 00 00 00 00 00 00
00 00 22 22 22 22 22 22 1C 00 00 00 00 00 00 00
00 00 22 22 22 14 14 08 08 00 00 00 00 00 00 00
00 00 22 22 22 2A 2A 36 22 00 00 00 00 00 00 00
00 00 22 22 14 08 14 22 22 00 00 00 00 00 00 00
00 00 22 22 14 08 08 08 08 00 00 00 00 00 00 00
00 00 3E 02 04 08 10 20 3E 00 00 00 00 00 00 00
00 00 38 20 20 20 20 20 38 00 00 00 00 00 00 00
00 00 20 20 10 08 04 02 02 00 00 00 00 00 00 00
00 00 0E 02 02 02 02 02 0E 00 00 00 00 00 00 00
00 00 08 1C 2A 08 08 08 08 00 00 00 00 00 00 00
00 00 00 08 10 3E 10 08 00 00 00 00 00 00 00 00
00 00 08 14 22 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 1C 02 1E 22 1E 00 00 00 00 00 00 00
00 00 20 20 2C 32 22 32 2C 00 00 00 00 00 00 00
00 00 00 00 1C 22 20 22 1C 00 00 00 00 00 00 00
00 00 02 02 1A 26 22 26 1A 00 00 00 00 00 00 00
00 00 00 00 1C 22 3E 20 1C 00 00 00 00 00 00 00
00 00 04 0A 08 1C 08 08 08 00 00 00 00 00 00 00
00 00 00 00 1A 26 26 1A 02 1C 00 00 00 00 00 00
00 00 20 20 2C 32 22 22 22 00 00 00 00 00 00 00
00 00 00 08 00 18 08 08 1C 00 00 00 00 00 00 00
00 00 00 02 00 02 02 02 22 1C 00 00 00 00 00 00
00 00 20 20 24 28 30 28 24 00 00 00 00 00 00 00
00 00 18 08 08 08 08 08 1C 00 00 00 00 00 00 00
00 00 00 00 14 2A 2A 2A 2A 00 00 00 00 00 00 00
00 00 00 00 2C 32 22 22 22 00 00 00 00 00 00 00
00 00 00 00 1C 22 22 22 1C 00 00 00 00 00 00 00
00 00 00 00 2C 32 32 2C 20 20 00 00 00 00 00 00
00 00 00 00 1A 26 26 1A 02 02 00 00 00 00 00 00
00 00 00 00 2C 32 20 20 20 00 00 00 00 00 00 00
00 00 00 00 1E 20 1C 02 3C 00 00 00 00 00 00 00
00 00 10 10 38 10 10 12 0C 00 00 00 00 00 00 00
00 00 00 00 22 22 22 26 1A 00 00 00 00 00 00 00
00 00 00 00 22 22 22 14 08 00 00 00 00 00 00 00
00 00 00 00 22 2A 2A 14 14 00 00 00 00 00 00 00
00 00 00 00 22 14 08 14 22 00 00 00 00 00 00 00
00 00 00 00 22 22 22 1E 02 1C 00 00 00 00 00 00
00 00 00 00 3E 04 08 10 3E 00 00 00 00 00 00 00
00 00 08 10 10 20 10 10 08 00 00 00 00 00 00 00
00 00 08 08 08 00 08 08 08 00 00 00 00 00 00 00
00 00 08 04 04 02 04 04 08 00 00 00 00 00 00 00
00 00 10 2A 04 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 3E 00 00 00 00 00 00 00
+102
View File
@@ -0,0 +1,102 @@
//============================================================================
// Verilog conversions of the CoCo3 ROM entities in rtl/rom/*.vhd.
//
// Line-for-line translations: same entity names, same ports, same clocking.
// The three loadable ROMs are single-clock RAMs filled over ioctl; while a
// write is in progress the read register holds its previous value, exactly as
// the VHDL `if WRITE = '1' ... else DATA <= ...` does.
//============================================================================
// rtl/rom/coco_rom_32K.vhd -- CoCo3 system ROM (boot0.rom, ioctl index 0)
module COCO_ROM_32K
(
input [14:0] ADDR,
output reg [7:0] DATA,
input CLK,
input [14:0] WR_ADDR,
input [7:0] WR_DATA,
input WRITE
);
reg [7:0] ROM [0:32767];
always @(posedge CLK) begin
if (WRITE) ROM[WR_ADDR] <= WR_DATA;
else DATA <= ROM[ADDR];
end
endmodule
// rtl/rom/coco_rom_8K.vhd -- Disk BASIC ROM (boot1.rom, ioctl index 64)
module COCO_ROM_8K
(
input [12:0] ADDR,
output reg [7:0] DATA,
input CLK,
input [12:0] WR_ADDR,
input [7:0] WR_DATA,
input WRITE
);
reg [7:0] ROM [0:8191];
always @(posedge CLK) begin
if (WRITE) ROM[WR_ADDR] <= WR_DATA;
else DATA <= ROM[ADDR];
end
endmodule
// rtl/rom/coco_rom_cart.vhd -- Program Pak, up to 128K (ioctl index 1)
module COCO_ROM_CART
(
input [16:0] ADDR,
output reg [7:0] DATA,
input CLK,
input [16:0] WR_ADDR,
input [7:0] WR_DATA,
input WRITE
);
reg [7:0] ROM [0:131071];
always @(posedge CLK) begin
if (WRITE) ROM[WR_ADDR] <= WR_DATA;
else DATA <= ROM[ADDR];
end
endmodule
// rtl/rom/coco_rom_16.vhd -- the AMW (automatic memory write) script: three
// {valid, a24..a0, data} records followed by a terminator. Asynchronous.
module COCO_ROM_16
(
input [3:0] ADDR,
output reg [7:0] DATA
);
always @(*) begin
case (ADDR)
// Clear $71 [Warm Start Flag]
4'd0: DATA = 8'h80; 4'd1: DATA = 8'h07; 4'd2: DATA = 8'h00;
4'd3: DATA = 8'h71; 4'd4: DATA = 8'h00;
// Set $C000 <- $55 [Clear D in DK identifier in rom]
4'd5: DATA = 8'h80; 4'd6: DATA = 8'h07; 4'd7: DATA = 8'hC0;
4'd8: DATA = 8'h00; 4'd9: DATA = 8'h55;
// Clear $72 [Warm Start Jump]
4'd10: DATA = 8'h80; 4'd11: DATA = 8'h07; 4'd12: DATA = 8'h00;
4'd13: DATA = 8'h72; 4'd14: DATA = 8'h00;
// terminator
default: DATA = 8'h00;
endcase
end
endmodule
// rtl/rom/coco3_char_rom.vhd -- 4K font RAM, preloaded with the CoCo3 font
// (verilator/rtl/coco3_char_rom.mem, extracted from the VHDL by gen_mem.py).
// Separate write and registered-read clocks, as in the VHDL.
module coco3_Char_ROM
(
input RD_CLK,
input [11:0] ADDR_R,
output reg [7:0] DATA_R,
input WR_CLK,
input WE,
input [11:0] ADDR_W,
input [7:0] DATA_W
);
reg [7:0] RAM [0:4095];
initial $readmemh("rtl/coco3_char_rom.mem", RAM);
always @(posedge WR_CLK) if (WE) RAM[ADDR_W] <= DATA_W;
always @(posedge RD_CLK) DATA_R <= RAM[ADDR_R];
endmodule
+33
View File
@@ -0,0 +1,33 @@
//============================================================================
// Verilog conversions of rtl/sram/*.vhd: synchronous write, asynchronous
// read, matching the VHDL (`DATA_O <= SRAM(ADDR)` outside the process).
//============================================================================
// rtl/sram/coco_ram.vhd -- 64K cassette buffer (R_W low = write)
module COCO_SRAM
(
input CLK,
input [15:0] ADDR,
input R_W,
input [7:0] DATA_I,
output [7:0] DATA_O
);
reg [7:0] SRAM [0:65535];
always @(posedge CLK) if (!R_W) SRAM[ADDR] <= DATA_I;
assign DATA_O = SRAM[ADDR];
endmodule
// rtl/sram/coco_vid_ram_buf.vhd -- 512 x 16 video line buffer
module COCO_VID_RAM_BUF
(
input CLK,
input [8:0] ADDR_I,
input [8:0] ADDR_O,
input WE,
input [15:0] DATA_I,
output [15:0] DATA_O
);
reg [15:0] SRAM [0:511];
always @(posedge CLK) if (WE) SRAM[ADDR_I] <= DATA_I;
assign DATA_O = SRAM[ADDR_O];
endmodule
+111
View File
@@ -0,0 +1,111 @@
// Verilog translation of rtl/OVO.vhd (the debug / "NO ROM" text overlay) for the
// simulation, since the simulator cannot read VHDL. Same ports, generics and timing: two
// cycles of video delay, probes latched at Hcount = Vcount = 0, 8x8 font.
//
// VHDL bit order: vin0/vin1 are (0 TO COLS*5-1), so character 0 is the
// leftmost 5 bits of in0/in1, i.e. the first entry of the concatenation in
// coco3fpga.sv; a font row's bit 0 is the leftmost pixel.
module ovo #(
parameter COLS = 32,
parameter LINES = 2,
parameter RGB = 24'hFFFFFF,
parameter H_OFFSET = 4,
parameter V_OFFSET = 45
) (
input [7:0] i_r,
input [7:0] i_g,
input [7:0] i_b,
input i_clk,
input [10:0] i_Hcount,
input [9:0] i_VCount,
output reg [7:0] o_r,
output reg [7:0] o_g,
output reg [7:0] o_b,
input ena,
input [COLS*5-1:0] in0,
input [COLS*5-1:0] in1
);
localparam N = COLS*5;
reg [7:0] chars [0:255];
initial begin
{chars[ 0],chars[ 1],chars[ 2],chars[ 3],chars[ 4],chars[ 5],chars[ 6],chars[ 7]} = 64'h3E63737B6F673E00; // 0
{chars[ 8],chars[ 9],chars[ 10],chars[ 11],chars[ 12],chars[ 13],chars[ 14],chars[ 15]} = 64'h0C0E0C0C0C0C3F00; // 1
{chars[ 16],chars[ 17],chars[ 18],chars[ 19],chars[ 20],chars[ 21],chars[ 22],chars[ 23]} = 64'h1E33301C06333F00; // 2
{chars[ 24],chars[ 25],chars[ 26],chars[ 27],chars[ 28],chars[ 29],chars[ 30],chars[ 31]} = 64'h1E33301C30331E00; // 3
{chars[ 32],chars[ 33],chars[ 34],chars[ 35],chars[ 36],chars[ 37],chars[ 38],chars[ 39]} = 64'h383C36337F307800; // 4
{chars[ 40],chars[ 41],chars[ 42],chars[ 43],chars[ 44],chars[ 45],chars[ 46],chars[ 47]} = 64'h3F031F3030331E00; // 5
{chars[ 48],chars[ 49],chars[ 50],chars[ 51],chars[ 52],chars[ 53],chars[ 54],chars[ 55]} = 64'h1C06031F33331E00; // 6
{chars[ 56],chars[ 57],chars[ 58],chars[ 59],chars[ 60],chars[ 61],chars[ 62],chars[ 63]} = 64'h3F3330180C0C0C00; // 7
{chars[ 64],chars[ 65],chars[ 66],chars[ 67],chars[ 68],chars[ 69],chars[ 70],chars[ 71]} = 64'h1E33331E33331E00; // 8
{chars[ 72],chars[ 73],chars[ 74],chars[ 75],chars[ 76],chars[ 77],chars[ 78],chars[ 79]} = 64'h1E33333E30180E00; // 9
{chars[ 80],chars[ 81],chars[ 82],chars[ 83],chars[ 84],chars[ 85],chars[ 86],chars[ 87]} = 64'h0C1E33333F333300; // A
{chars[ 88],chars[ 89],chars[ 90],chars[ 91],chars[ 92],chars[ 93],chars[ 94],chars[ 95]} = 64'h3F66663E66663F00; // B
{chars[ 96],chars[ 97],chars[ 98],chars[ 99],chars[100],chars[101],chars[102],chars[103]} = 64'h3C66030303663C00; // C
{chars[104],chars[105],chars[106],chars[107],chars[108],chars[109],chars[110],chars[111]} = 64'h1F36666666361F00; // D
{chars[112],chars[113],chars[114],chars[115],chars[116],chars[117],chars[118],chars[119]} = 64'h7F46161E16467F00; // E
{chars[120],chars[121],chars[122],chars[123],chars[124],chars[125],chars[126],chars[127]} = 64'h7F46161E16060F00; // F
{chars[128],chars[129],chars[130],chars[131],chars[132],chars[133],chars[134],chars[135]} = 64'h0000000000000000; // ' ' 10
{chars[136],chars[137],chars[138],chars[139],chars[140],chars[141],chars[142],chars[143]} = 64'h00003F00003F0000; // = 11
{chars[144],chars[145],chars[146],chars[147],chars[148],chars[149],chars[150],chars[151]} = 64'h000C0C3F0C0C0000; // + 12
{chars[152],chars[153],chars[154],chars[155],chars[156],chars[157],chars[158],chars[159]} = 64'h0000003F00000000; // - 13
{chars[160],chars[161],chars[162],chars[163],chars[164],chars[165],chars[166],chars[167]} = 64'h180C0603060C1800; // < 14
{chars[168],chars[169],chars[170],chars[171],chars[172],chars[173],chars[174],chars[175]} = 64'h060C1830180C0600; // > 15
{chars[176],chars[177],chars[178],chars[179],chars[180],chars[181],chars[182],chars[183]} = 64'h081C366341000000; // ^ 16
{chars[184],chars[185],chars[186],chars[187],chars[188],chars[189],chars[190],chars[191]} = 64'h081C366341000000; // v 17
{chars[192],chars[193],chars[194],chars[195],chars[196],chars[197],chars[198],chars[199]} = 64'h180C0606060C1800; // ( 18
{chars[200],chars[201],chars[202],chars[203],chars[204],chars[205],chars[206],chars[207]} = 64'h060C1818180C0600; // ) 19
{chars[208],chars[209],chars[210],chars[211],chars[212],chars[213],chars[214],chars[215]} = 64'h000C0C00000C0C00; // : 1A
{chars[216],chars[217],chars[218],chars[219],chars[220],chars[221],chars[222],chars[223]} = 64'h4143454951614100; // N 1B
{chars[224],chars[225],chars[226],chars[227],chars[228],chars[229],chars[230],chars[231]} = 64'h3E41414141413E00; // O 1C
{chars[232],chars[233],chars[234],chars[235],chars[236],chars[237],chars[238],chars[239]} = 64'h3F41413F11214100; // R 1D
{chars[240],chars[241],chars[242],chars[243],chars[244],chars[245],chars[246],chars[247]} = 64'h4163554941414100; // M 1E
{chars[248],chars[249],chars[250],chars[251],chars[252],chars[253],chars[254],chars[255]} = 64'h36367F367F363600; // # 1F
end
reg [N-1:0] in0s, in1s, vin0, vin1;
reg [7:0] t_r, t_g, t_b;
reg [11:0] hcpt, hcpt2, vcpt;
reg [7:0] col;
wire [N-1:0] vin_v = vcpt[3] ? vin1 : vin0; // (vcpt/8) mod 2
wire [11:0] cidx = hcpt >> 3;
wire [4:0] char_v = (hcpt < COLS*8 && vcpt < LINES*8) ? vin_v[N-1-cidx*5 -: 5] : 5'b10000;
always @(posedge i_clk) begin
in0s <= in0;
in1s <= in1;
t_r <= i_r;
t_g <= i_g;
t_b <= i_b;
if (i_Hcount == 0 && i_VCount == 0) begin
vin0 <= in0s;
vin1 <= in1s;
end
hcpt <= (i_Hcount < H_OFFSET) ? COLS*8 : {1'b0, i_Hcount} - H_OFFSET;
vcpt <= (i_VCount < V_OFFSET) ? 12'd512 : {2'b0, i_VCount} - V_OFFSET;
hcpt2 <= hcpt;
col <= chars[{char_v, vcpt[2:0]}];
if (ena && col[hcpt2[2:0]]) begin
o_r <= RGB[23:16];
o_g <= RGB[15:8];
o_b <= RGB[7:0];
end else begin
o_r <= t_r;
o_g <= t_g;
o_b <= t_b;
end
end
endmodule
+327
View File
@@ -0,0 +1,327 @@
//============================================================================
// Simulation replacement for rtl/sdram/sdram2.sv (module sdram_32r8w).
//
// The controller below is rtl/sdram/sdram2.sv copied verbatim -- the same
// state machine, refresh schedule, CAS/burst delays and ack/ready timing the
// core is written against. Only the pins changed:
//
// - SDRAM_DQ is not a tristate. The controller's drive is SDRAM_DQ (a reg
// that it sets to 16'bZ when idle, harmless here) and what it samples is
// chip_dq, driven by the chip model at the bottom of this file.
// - The block-local registers of the main always block are declared at
// module scope instead; see the note there.
// - The altddio_out that forwards the (inverted) clock to the chip is gone;
// the chip model samples the controller's registered command one clk
// later, which is where the inverted SDRAM_CLK edge lands.
//
// Chip model: one 32 MB x16 SDR SDRAM, CAS latency 3, sequential burst 2,
// single-word writes, DQM byte masks on A[12:11] -- the mode sdram2.sv
// programs. A READ registered at clk edge k (command <= CMD_READ) makes word 0
// land in dq_reg at edge k+4 and word 1 at k+5, which is exactly when the
// controller's data_*_ready_delay taps say the data is there.
//============================================================================
module sdram_32r8w
(
input init, // reset to initialize RAM
input clk, // clock ~100MHz
// CPU R/W port
input [24:0] sdram_cpu_addr, // 25 bit address for 8bit mode.
output [15:0] sdram_dout, // data output to cpu [for both ports]
input [7:0] sdram_cpu_din, // data input from cpu
input sdram_cpu_req, // request
input sdram_cpu_rnw, // 1 - read, 0 - write
output reg sdram_cpu_ack, // 1 = ack
output reg sdram_cpu_ready, // dout is valid. Ready to accept new read/write.
// Video R port
input [24:0] sdram_vid_addr, // 25 bit A0=0.
input sdram_vid_req, // request
output reg sdram_vid_ack, // 1 = ack
output reg sdram_vid_ready, // dout is valid. Ready to accept new read/write.
output reg sdram_busy // doing something...
);
reg [15:0] SDRAM_DQ;
reg [12:0] SDRAM_A;
reg [1:0] SDRAM_BA;
reg [15:0] chip_dq;
assign sdram_dout = dq_reg;
// Burst length = 4
localparam BURST_LENGTH = 2;
localparam BURST_CODE = (BURST_LENGTH == 8) ? 3'b011 : (BURST_LENGTH == 4) ? 3'b010 : (BURST_LENGTH == 2) ? 3'b001 : 3'b000; // 000=1, 001=2, 010=4, 011=8
localparam ACCESS_TYPE = 1'b0; // 0=sequential, 1=interleaved
localparam CAS_LATENCY = 3'd3; // 2 for < 100MHz, 3 for >100MHz
localparam OP_MODE = 2'b00; // only 00 (standard operation) allowed
localparam NO_WRITE_BURST = 1'b1; // 0= write burst enabled, 1=only single access write
localparam MODE = {3'b000, NO_WRITE_BURST, OP_MODE, CAS_LATENCY, ACCESS_TYPE, BURST_CODE};
localparam sdram_startup_cycles= 14'd12100;// 100us, plus a little more, @ 100MHz
localparam startup_refresh_max = 14'b11111111111111;
//localparam cycles_per_refresh = 14'd780; // (64000*100)/8192-1 Calc'd as (64ms @ 100MHz)/8192 rose
localparam cycles_per_refresh = 14'd890; // (64000*100)/8192-1 Calc'd as (64ms @ 114.560MHz)/8192 rose (act 895)
// SDRAM commands
wire [2:0] CMD_NOP = 3'b111;
wire [2:0] CMD_ACTIVE = 3'b011;
wire [2:0] CMD_READ = 3'b101;
wire [2:0] CMD_WRITE = 3'b100;
wire [2:0] CMD_PRECHARGE = 3'b010;
wire [2:0] CMD_AUTO_REFRESH = 3'b001;
wire [2:0] CMD_LOAD_MODE = 3'b000;
reg [13:0] refresh_count = startup_refresh_max - sdram_startup_cycles;
reg [2:0] command;
localparam STATE_STARTUP = 0;
localparam STATE_WAIT = 1;
localparam STATE_WAIT1 = 2;
localparam STATE_RW1 = 3;
localparam STATE_IDLE = 4;
localparam STATE_DLY1 = 5;
localparam STATE_DLY2 = 6;
localparam STATE_IDLE_7 = 17;
localparam STATE_IDLE_6 = 16;
localparam STATE_IDLE_5 = 15;
localparam STATE_IDLE_4 = 14;
localparam STATE_IDLE_3 = 13;
localparam STATE_IDLE_2 = 12;
localparam STATE_IDLE_1 = 11;
reg [15:0] dq_reg;
// In the original these are declared inside the always block below, with
// `state` initialised there. Verilator (5.044) re-applies a block-local
// initialiser every time the block runs, so `state` was forced back to
// STATE_STARTUP on every clock and no request was ever served. At module scope
// the initialiser runs once, as Quartus treats it.
reg [CAS_LATENCY+BURST_LENGTH:0] data_cpu_ready_delay;
reg [CAS_LATENCY+BURST_LENGTH:0] data_vid_ready_delay;
reg saved_wr;
reg saved_vid;
reg [12:0] cas_addr;
reg [31:0] saved_data;
reg [4:0] state = STATE_STARTUP;
always @(posedge clk) begin
refresh_count <= refresh_count + 1'b1;
data_vid_ready_delay[CAS_LATENCY+BURST_LENGTH] <= 0;
data_cpu_ready_delay[CAS_LATENCY+BURST_LENGTH] <= 0;
data_cpu_ready_delay <= data_cpu_ready_delay>>1;
data_vid_ready_delay <= data_vid_ready_delay>>1;
dq_reg <= chip_dq;
// if(data_ready_delay[1]) sdram_ldout[15:00] <= dq_reg;
// if(data_ready_delay[0]) sdram_ldout[31:16] <= dq_reg;
sdram_cpu_ready <= 1'b0;
sdram_vid_ready <= 1'b0;
if (data_cpu_ready_delay[2]) sdram_cpu_ready <= 1'b1; // Data valid for the first 16 bits
if (data_cpu_ready_delay[1]) sdram_busy <= 1'b0;
if (data_vid_ready_delay[2]) sdram_vid_ready <= 1'b1; // Data valid for the first 16 bits
if (data_vid_ready_delay[1]) sdram_vid_ready <= 1'b1; // Data valid for the second 16 bits
if (data_vid_ready_delay[0]) sdram_busy <= 1'b0;
SDRAM_DQ <= 16'h0000; // was 16'bZ: the bus is not tristated here
command <= CMD_NOP;
if (!sdram_cpu_req)
sdram_cpu_ack <= 1'b0;
if (!sdram_vid_req)
sdram_vid_ack <= 1'b0;
case (state)
STATE_STARTUP: begin
SDRAM_A <= 0;
SDRAM_BA <= 0;
sdram_cpu_ready <= 0; //not ready
sdram_vid_ready <= 0; //not ready
sdram_busy <= 1'b1;
// All the commands during the startup are NOPS, except these
if (refresh_count == startup_refresh_max-31) begin
// ensure all rows are closed
command <= CMD_PRECHARGE;
SDRAM_A[10] <= 1; // all banks
SDRAM_BA <= 2'b00;
end
if (refresh_count == startup_refresh_max-23) begin
// these refreshes need to be at least tREF (66ns) apart
command <= CMD_AUTO_REFRESH;
end
if (refresh_count == startup_refresh_max-15) begin
command <= CMD_AUTO_REFRESH;
end
if (refresh_count == startup_refresh_max-7) begin
// Now load the mode register
command <= CMD_LOAD_MODE;
SDRAM_A <= MODE;
end
if (!refresh_count) begin
state <= STATE_IDLE;
sdram_busy <= 1'b0;
refresh_count <= 0;
end
end
STATE_IDLE_7: state <= STATE_IDLE_6;
STATE_IDLE_6: state <= STATE_IDLE_5;
STATE_IDLE_5: state <= STATE_IDLE_4;
STATE_IDLE_4: state <= STATE_IDLE_3;
STATE_IDLE_3: state <= STATE_IDLE_2;
STATE_IDLE_2: state <= STATE_IDLE_1;
STATE_IDLE_1: begin
state <= STATE_IDLE;
sdram_busy <= 1'b0;
// mask possible refresh to reduce colliding.
if(refresh_count > cycles_per_refresh) begin
state <= STATE_IDLE_7;
command <= CMD_AUTO_REFRESH;
refresh_count <= 0;
sdram_busy <= 1'b1;
end
end
STATE_IDLE: begin
saved_vid <= 1'b0;
if(refresh_count > (cycles_per_refresh<<1))
begin
state <= STATE_IDLE_1;
sdram_busy <= 1'b1;
end
else
begin
if(sdram_cpu_req & !sdram_cpu_ack) // request has to go away after ready=0
begin
// fix byte writes [no new command until data is actually written]
if (~sdram_cpu_rnw)
{cas_addr[12:9],SDRAM_BA,SDRAM_A,cas_addr[8:0]} <= {~sdram_cpu_addr[0], sdram_cpu_addr[0], 2'b10, sdram_cpu_addr[24:1]}; // Bytes by A0 for writes
else
{cas_addr[12:9],SDRAM_BA,SDRAM_A,cas_addr[8:0]} <= {2'b00, 2'b10, sdram_cpu_addr[24:1]}; // No bytes for reads...
saved_data <= {sdram_cpu_din, sdram_cpu_din};
saved_wr <= ~sdram_cpu_rnw;
command <= CMD_ACTIVE;
state <= STATE_WAIT;
sdram_busy <= 1'b1;
end
else
begin
if (sdram_vid_req)
begin
{cas_addr[12:9],SDRAM_BA,SDRAM_A,cas_addr[8:0]} <= {2'b00, 2'b10, sdram_vid_addr[24:1]}; // No bytes for reads...
command <= CMD_ACTIVE;
saved_vid <= 1'b1;
saved_wr <= 1'b0;
sdram_busy <= 1'b1;
state <= STATE_WAIT;
end
end
end
end
STATE_WAIT: state <= STATE_WAIT1;
STATE_WAIT1: begin
if (saved_wr)
begin
if ((data_vid_ready_delay[5:1] == 5'b00000) && (data_cpu_ready_delay[5:1] == 5'b00000))
state <= STATE_RW1; // added for clk > 100Mhz
end
else
state <= STATE_RW1; // added for clk > 100Mhz
end
STATE_RW1: begin
SDRAM_A <= cas_addr;
if (saved_vid)
sdram_vid_ack <= 1'b1;
else
sdram_cpu_ack <= 1'b1;
if(saved_wr) begin
command <= CMD_WRITE;
SDRAM_DQ <= saved_data[15:0];
// state <= STATE_IDLE;
state <= STATE_DLY1;
sdram_cpu_ready <= 1'b1; // write done
sdram_busy <= 1'b0;
end
else begin
command <= CMD_READ;
state <= STATE_IDLE;
if (saved_vid)
begin
data_vid_ready_delay[CAS_LATENCY+BURST_LENGTH] <= 1;
state <= STATE_DLY1;
end
else
data_cpu_ready_delay[CAS_LATENCY+BURST_LENGTH] <= 1;
state <= STATE_DLY1;
end
end
STATE_DLY1:
state <= STATE_DLY2;
STATE_DLY2:
state <= STATE_IDLE;
endcase
if (init) begin
sdram_cpu_ack <= 1'b0;
sdram_vid_ack <= 1'b0;
state <= STATE_STARTUP;
refresh_count <= startup_refresh_max - sdram_startup_cycles;
end
end
//----------------------------------------------------------------------------
// SDR SDRAM chip model
//----------------------------------------------------------------------------
reg [15:0] chip_mem [0:(1<<24)-1];
reg [12:0] chip_row [0:3];
reg rd_p1, rd_p2, rd_w1;
reg [23:0] rd_a1, rd_a2, rd_aw;
wire [23:0] cmd_addr = {SDRAM_BA, chip_row[SDRAM_BA], SDRAM_A[8:0]};
always @(posedge clk) begin
case (command)
3'b011: chip_row[SDRAM_BA] <= SDRAM_A; // ACTIVE
3'b100: begin // WRITE
if (!SDRAM_A[11]) chip_mem[cmd_addr][7:0] <= SDRAM_DQ[7:0];
if (!SDRAM_A[12]) chip_mem[cmd_addr][15:8] <= SDRAM_DQ[15:8];
end
default: ;
endcase
// READ: two pipeline stages, then word 0 and word 1 on consecutive edges.
rd_p1 <= (command == 3'b101);
rd_a1 <= cmd_addr;
rd_p2 <= rd_p1;
rd_a2 <= rd_a1;
rd_w1 <= rd_p2;
rd_aw <= {rd_a2[23:1], ~rd_a2[0]}; // burst 2, sequential
if (rd_p2) chip_dq <= chip_mem[rd_a2];
else if (rd_w1) chip_dq <= chip_mem[rd_aw];
else chip_dq <= 16'h0000;
end
endmodule
+32
View File
@@ -0,0 +1,32 @@
0000 0010 0020 0030 0040 0050 0060 0070
0080 0090 00A0 00B0 00C0 00D0 00E0 00F0
0100 0110 0120 0130 0140 0150 0160 0170
0180 0190 01A0 01B0 01C0 01D0 01E0 01F0
0200 0210 0220 0230 0240 0250 0260 0270
0280 0290 02A0 02B0 02C0 02D0 02E0 02F0
0300 0310 0320 0330 0340 0350 0360 0370
0380 0390 03A0 03B0 03C0 03D0 03E0 03F0
0400 0410 0420 0430 0440 0450 0460 0470
0480 0490 04A0 04B0 04C0 04D0 04E0 04F0
0500 0510 0520 0530 0540 0550 0560 0570
0580 0590 05A0 05B0 05C0 05D0 05E0 05F0
0600 0610 0620 0630 0640 0650 0660 0670
0680 0690 06A0 06B0 06C0 06D0 06E0 06F0
0700 0710 0720 0730 0740 0750 0760 0770
0780 0790 07A0 07B0 07C0 07D0 07E0 07F0
0800 0810 0820 0830 0840 0850 0860 0870
0880 0890 08A0 08B0 08C0 08D0 08E0 08F0
0900 0910 0920 0930 0940 0950 0960 0970
0980 0990 09A0 09B0 09C0 09D0 09E0 09F0
0A00 0A10 0A20 0A30 0A40 0A50 0A60 0A70
0A80 0A90 0AA0 0AB0 0AC0 0AD0 0AE0 0AF0
0B00 0B10 0B20 0B30 0B40 0B50 0B60 0B70
0B80 0B90 0BA0 0BB0 0BC0 0BD0 0BE0 0BF0
0C00 0C10 0C20 0C30 0C40 0C50 0C60 0C70
0C80 0C90 0CA0 0CB0 0CC0 0CD0 0CE0 0CF0
0D00 0D10 0D20 0D30 0D40 0D50 0D60 0D70
0D80 0D90 0DA0 0DB0 0DC0 0DD0 0DE0 0DF0
0E00 0E10 0E20 0E30 0E40 0E50 0E60 0E70
0E80 0E90 0EA0 0EB0 0EC0 0ED0 0EE0 0EF0
0F00 0F10 0F20 0F30 0F40 0F50 0F60 0F70
0F80 0F90 0FA0 0FB0 0FC0 0FD0 0FE0 0FF0
+112
View File
@@ -0,0 +1,112 @@
#!/usr/bin/env bash
#
# Headless smoke tests for the CoCo3 sim. Each test boots the machine, types at
# BASIC on a frame schedule, and is judged two ways:
#
# * the TEXT SCREEN ($0400, as the CPU wrote it) must contain every expected
# string -- this is what says the machine did the right thing;
# * the final SCREENSHOT is compared byte for byte with $REF/<name>.png --
# this is what catches a video change nobody meant to make.
#
# The sim is deterministic, so a screenshot only moves when the RTL (or the
# harness) moves it. When a change is intentional, bless the new references:
#
# BLESS=1 ./run_tests.sh
#
# A test with no reference is reported "new" and does not fail the run.
# Tests run in parallel; each is a few minutes (the sim runs at ~1.2 frames/s,
# and the core's own power-on reset plus the BASIC banner take ~130 frames).
#
# ./run_tests.sh all tests
# ./run_tests.sh boot disk just those
#
# Needs roms/boot0.rom (CoCo3 ROM) and roms/boot1.rom (Disk BASIC 1.1); see
# README.md.
set -u
cd "$(dirname "$0")"
EXE=./obj_dir/Vemu
OUT=${OUT:-test-out}
SIMARGS=${SIMARGS:-} # extra sim options for every test, e.g. --fast-clocks
REF=${REF:-test-ref}
mkdir -p "$OUT" "$REF"
if [ ! -x "$EXE" ]; then echo "build first: make"; exit 2; fi
for r in roms/boot0.rom roms/boot1.rom; do
[ -f "$r" ] || { echo "missing $r -- see README.md"; exit 2; }
done
[ -f tests/hello.dsk ] || python3 tests/make_test_disk.py >/dev/null
# name | stop frame | extra args | expected strings (;-separated)
TESTS=(
"boot|150||DISK EXTENDED COLOR BASIC 2.1;OK"
"keyboard|260|--type '140:PRINT 2+2\\n'|PRINT 2+2; 4"
"disk|420|--disk tests/hello.dsk --type '140:RUN\"HELLO\\n'|HELLO FROM DISK; 42"
# GIME modes. --ascii only reads the 32-column VDG screen, so these two are
# judged on the screenshot alone.
"width80|330|--type '140:WIDTH 80\\nPRINT \"80 COLUMNS\"\\n'|"
"hscreen|560|--type '140:HSCREEN2:HCIRCLE(160,96),60,4:HLINE(0,0)-(319,191),PSET,B:FORI=1TO9E9:NEXT\\n'|"
)
want=("$@")
selected() {
[ ${#want[@]} -eq 0 ] && return 0
for w in "${want[@]}"; do [ "$w" = "$1" ] && return 0; done
return 1
}
pids=()
names=()
for t in "${TESTS[@]}"; do
IFS='|' read -r name stop extra expect <<<"$t"
selected "$name" || continue
# shellcheck disable=SC2086
eval "set -- $extra"
# shellcheck disable=SC2086
( "$EXE" --headless --stop-at-frame "$stop" $SIMARGS "$@" \
--screenshot "$stop" --screenshot-prefix "$OUT/$name" --ascii-end \
> "$OUT/$name.log" 2>&1 ) &
pids+=($!)
names+=("$name")
done
for p in "${pids[@]}"; do wait "$p"; done
fail=0
printf "%-10s %-6s %-9s %s\n" TEST SCREEN IMAGE NOTES
for t in "${TESTS[@]}"; do
IFS='|' read -r name stop extra expect <<<"$t"
selected "$name" || continue
log="$OUT/$name.log"
shot=$(printf "%s/%s_frame_%04d.png" "$OUT" "$name" "$stop")
notes=""
screen=ok
if [ -n "$expect" ]; then # bash 3.2: an empty array is "unbound" under set -u
IFS=';' read -r -a strings <<<"$expect"
for s in "${strings[@]}"; do
if ! grep -qF -- "|$s" "$log"; then screen=FAIL; notes="$notes missing \"$s\";"; fi
done
else
screen=-
fi
image=ok
if [ ! -f "$shot" ]; then
image=FAIL; notes="$notes no screenshot;"
elif [ -n "${BLESS:-}" ]; then
cp "$shot" "$REF/$name.png"; image=blessed
elif [ ! -f "$REF/$name.png" ]; then
image=new
elif ! cmp -s "$shot" "$REF/$name.png"; then
image=CHANGED; notes="$notes differs from $REF/$name.png;"
fi
[ "$screen" = FAIL ] && fail=1
[ "$image" = FAIL ] || [ "$image" = CHANGED ] && fail=1
notes="$notes $(grep -o 'Finished at frame.*' "$log" | sed 's/, active.*//')"
printf "%-10s %-6s %-9s %s\n" "$name" "$screen" "$image" "$notes"
done
exit $fail
+172
View File
@@ -0,0 +1,172 @@
#include "serial.h"
#include <algorithm>
#include <cerrno>
#include <cstdlib>
#include <cstring>
#include <fcntl.h>
#include <termios.h>
#include <unistd.h>
static const double CLK_SYS_HZ = 57272727.0;
static const int XTAL_DIV = 31; // coco3fpga.sv CLK_6551_EN
static const size_t HIST_MAX = 4096;
// uart_6551.v: TX_CLK_DIV wraps after this many enables for CTL[3:0]; the
// baud clock toggles on each wrap and pulses on every second one.
static const int wrap_enables[16] = {
0, 1152, 768, 524, 428, 384, 192, 96, 48, 32, 24, 16, 12, 8, 6, 3
};
long SerialPort::bit_clks(uint8_t ctl) {
int sel = ctl & 0x0F;
// CTL[3:0] == 0: "16x external clock", which in this core is the
// 1.8475 MHz enable itself -- 115,469 baud.
long enables_per_16x = sel ? 2L * wrap_enables[sel] : 1L;
return XTAL_DIV * enables_per_16x * 16;
}
long SerialPort::rx_bit_clks(uint8_t ctl) {
// uart_6551.v: RX_CLK = TX_CLK, i.e. the receiver always runs off the baud
// generator. (It used to take the "external" 1.8475 MHz clock when CTL bit 4
// was 0, which made CTL=$0F transmit at 19,200 but receive at 115,200.)
return bit_clks(ctl);
}
double SerialPort::baud(long clks) { return CLK_SYS_HZ / (double)clks; }
bool SerialPort::open_pty() {
pty_fd = posix_openpt(O_RDWR | O_NOCTTY);
if (pty_fd < 0 || grantpt(pty_fd) < 0 || unlockpt(pty_fd) < 0) {
perror("serial: posix_openpt");
return false;
}
const char* name = ptsname(pty_fd);
if (!name) { perror("serial: ptsname"); return false; }
pty_name = name;
// Hold the slave open ourselves: otherwise reads on the master return EIO
// until something connects, and again whenever the far end reconnects.
pty_slave_fd = open(name, O_RDWR | O_NOCTTY);
if (pty_slave_fd >= 0) {
struct termios t;
if (tcgetattr(pty_slave_fd, &t) == 0) {
cfmakeraw(&t);
tcsetattr(pty_slave_fd, TCSANOW, &t);
}
}
fcntl(pty_fd, F_SETFL, fcntl(pty_fd, F_GETFL) | O_NONBLOCK);
printf("Serial: RS-232 Pak on pty %s\n", name);
fflush(stdout);
return true;
}
void SerialPort::queue_rx(const uint8_t* p, size_t n) {
rx_queue.insert(rx_queue.end(), p, p + n);
}
void SerialPort::poll_pty() {
if (pty_fd < 0) return;
uint8_t buf[256];
ssize_t n = read(pty_fd, buf, sizeof(buf));
if (n > 0) queue_rx(buf, (size_t)n);
}
void SerialPort::got_tx_byte(uint8_t b, bool framing_ok, int frame) {
tx_count++;
if (!framing_ok) tx_framing_errors++;
tx_hist.push_back(b);
if (tx_hist.size() > HIST_MAX) tx_hist.erase(tx_hist.begin());
tx_line.push_back(b);
if (log_file)
fprintf(log_file, "%6d TX %02X%s\n", frame, b, framing_ok ? "" : " framing error");
if (pty_fd >= 0) {
ssize_t w = write(pty_fd, &b, 1);
(void)w;
}
}
uint8_t SerialPort::clock(uint8_t txd, uint8_t ctl_now, uint8_t cmd_now, int frame) {
ctl = ctl_now;
cmd = cmd_now;
// ---- TX: decode what the 6551 puts on the pin ---------------------
const long bclk = bit_clks(ctl);
switch (tx_phase) {
case 0:
if (tx_last && !txd) { tx_phase = 1; tx_timer = bclk / 2; }
break;
case 1: // middle of the start bit
if (--tx_timer <= 0) {
if (txd) tx_phase = 0; // glitch, not a start bit
else { tx_phase = 2; tx_timer = bclk; tx_bitn = 0; tx_shift = 0; }
}
break;
case 2: // data bits, LSB first
if (--tx_timer <= 0) {
tx_shift |= (uint16_t)(txd & 1) << tx_bitn;
tx_timer = bclk;
if (++tx_bitn == data_bits(ctl)) tx_phase = (cmd & 0x20) ? 3 : 4;
}
break;
case 3: // parity (not checked)
if (--tx_timer <= 0) { tx_phase = 4; tx_timer = bclk; }
break;
case 4: // stop bit
if (--tx_timer <= 0) {
got_tx_byte((uint8_t)tx_shift, txd != 0, frame);
tx_phase = 0;
}
break;
}
tx_last = txd;
// ---- RX: drive the pin, 8N1 at the far end's rate -------------------
if (++poll_timer >= 4096) { poll_timer = 0; poll_pty(); }
if (rx_timer > 0) rx_timer--;
if (rx_timer == 0) {
if (rx_bits_left == 0 && !rx_queue.empty()) {
uint8_t b = rx_queue.front();
rx_queue.pop_front();
rx_count++;
rx_hist.push_back(b);
if (rx_hist.size() > HIST_MAX) rx_hist.erase(rx_hist.begin());
rx_line.push_back(b);
if (log_file) fprintf(log_file, "%6d RX %02X\n", frame, b);
rx_frame = (uint16_t)(1u << 9) | ((uint16_t)b << 1); // start 0, data, stop 1
rx_bits_left = 10;
}
if (rx_bits_left > 0) {
// Each bit, the stop bit included, is held for a full bit time.
rx_level = rx_frame & 1;
rx_frame >>= 1;
rx_bits_left--;
rx_timer = line_clks();
} else {
rx_level = 1;
}
}
return rx_level;
}
void SerialPort::print_line(const char* dir, std::vector<uint8_t>& v, int frame) {
if (v.empty()) return;
if (print_bytes) {
for (size_t i = 0; i < v.size(); i += 16) {
char hex[16 * 3 + 1] = {0}, asc[17] = {0};
size_t n = std::min<size_t>(16, v.size() - i);
for (size_t j = 0; j < n; j++) {
uint8_t c = v[i + j];
snprintf(hex + j * 3, 4, "%02X ", c);
asc[j] = (c >= 0x20 && c < 0x7f) ? (char)c : '.';
}
printf("SERIAL %s %6d %-48s |%s|\n", dir, frame, hex, asc);
}
fflush(stdout);
}
v.clear();
}
void SerialPort::end_frame(int frame) {
print_line("TX", tx_line, frame);
print_line("RX", rx_line, frame);
}
+81
View File
@@ -0,0 +1,81 @@
#pragma once
//============================================================================
// RS-232 Pak (glb6551) line model for the CoCo3 sim.
//
// Works on the pins, not on the registers: TXD is decoded as the far end of
// the cable would see it, and RXD is driven bit by bit. So a byte is only
// logged as transmitted if the 6551 really shifted it out, at the baud rate
// it was really programmed for.
//
// Clocked once per clk_sys (57.272727 MHz). Bit timing follows
// rtl/UART_6551/uart_6551.v: a 1.8475 MHz enable (clk_sys / 31) feeds the
// divider; the 6551 samples at 16x the bit rate.
//
// Optional pty bridge: the slave side (/dev/ttysNNN) can be opened by a
// DriveWire server or FujiNet-PC, or by socat to reach a TCP one. Note the sim
// runs ~50x slower than real time, so the far end sees ~400 baud of real
// throughput whatever the programmed rate is.
//============================================================================
#include <cstdint>
#include <cstdio>
#include <deque>
#include <string>
#include <vector>
struct SerialPort {
// --- configuration -------------------------------------------------
bool print_bytes = true; // SERIAL TX/RX lines on stdout
FILE* log_file = nullptr; // --serial-log: one line per byte
// Rate the far end sends at, in clk_sys cycles per bit. 0 = the rate the
// 6551 transmits at, i.e. a peer configured to match. RXD is driven at this
// rate whatever the 6551's RECEIVER is clocked at, so a receiver-clock
// mismatch shows up as garbage, as it would on the cable.
long line_bit_clks = 0;
long line_clks() const { return line_bit_clks ? line_bit_clks : bit_clks(ctl); }
// --- state visible to the UI ----------------------------------------
std::string pty_name;
long tx_count = 0, rx_count = 0;
long tx_framing_errors = 0;
std::vector<uint8_t> tx_hist, rx_hist; // capped, for the Serial window
uint8_t ctl = 0, cmd = 0; // last seen 6551 registers
// Bits per word and clk_sys cycles per bit for a control/command value.
static int data_bits(uint8_t ctl) { return 8 - ((ctl >> 5) & 3); }
static long bit_clks(uint8_t ctl); // transmitter / internal generator
static long rx_bit_clks(uint8_t ctl); // receiver (CTL bit 4 picks the source)
static double baud(long clks);
bool open_pty();
void queue_rx(const uint8_t* p, size_t n);
// One clk_sys cycle. Returns the level to drive on RXD.
uint8_t clock(uint8_t txd, uint8_t ctl, uint8_t cmd, int frame);
// Flush the per-frame byte lines.
void end_frame(int frame);
private:
// TX decoder
int tx_phase = 0; // 0 idle, 1 start, 2 data, 3 parity, 4 stop
long tx_timer = 0;
int tx_bitn = 0;
uint16_t tx_shift = 0;
uint8_t tx_last = 1;
// RX driver
std::deque<uint8_t> rx_queue;
uint16_t rx_frame = 0; // bits to send, LSB first
int rx_bits_left = 0;
long rx_timer = 0;
uint8_t rx_level = 1;
// pty
int pty_fd = -1, pty_slave_fd = -1;
long poll_timer = 0;
// per-frame print buffers
std::vector<uint8_t> tx_line, rx_line;
void got_tx_byte(uint8_t b, bool framing_ok, int frame);
void poll_pty();
void print_line(const char* dir, std::vector<uint8_t>& v, int frame);
};
+571
View File
@@ -0,0 +1,571 @@
//============================================================================
// CoCo3 Verilator simulation wrapper
//
// Stands in for CoCo3.sv (the MiSTer top level) without the sys/ framework:
// no hps_io, no PLL, no video_mixer. sim_main.cpp drives the clocks and the
// ioctl/block-device/keyboard ports; everything between those and the core
// is wired the way CoCo3.sv wires it, with the OSD `status` word decoded
// here by the same expressions.
//
// Deliberate differences from CoCo3.sv:
// - CLK_114/57/28/14 come straight from sim_main instead of the PLL. The PLL
// makes them 114.545454 / 57.272727 / 28.636363 / 14.318181 MHz, all
// phase 0, i.e. exact /2 /4 /8 divisions of one clock, which is what
// sim_main produces -- all four change in the same eval, so there is no
// derived-clock race between domains. CLK_50M (rtc.sv, the UART) is
// approximated by sim_main with a phase accumulator.
// - rtl/sdram/sdram2.sv is replaced by verilator/rtl/sdram2.sv: the same
// controller with an SDR chip model hung off it instead of SDRAM_* pins.
// - hps_io's keyboard path is reproduced from its parts: ps2_key events are
// turned into scan-code bytes and pushed into MiSTer's own ps2_device
// (sys/hps_io.sv) clocked exactly as hps_io clocks it with PS2DIV(2400),
// so cocokey.v sees the same PS/2 serial stream as on hardware.
// - The VHDL entities are replaced by their Verilog conversions in this
// directory: rtl/coco_rom.v, rtl/coco_sram.v. VDAC.v's altsyncram becomes an
// equivalent registered dual-port RAM.
//============================================================================
`timescale 1ns / 1ps
module emu
(
input CLK_114,
input CLK_57, // clk_sys
input CLK_28,
input CLK_14,
input CLK_50M,
input RESET,
// The OSD status word, bit-for-bit as hps_io would present it.
input [63:0] status,
input [1:0] buttons,
// [7:0] scancode, [8] extended, [9] pressed, [10] toggles per event
input [10:0] ps2_key,
input [24:0] ps2_mouse,
input [31:0] joy1,
input [31:0] joy2,
input [15:0] joya1,
input [15:0] joya2,
input [64:0] RTC,
// HPS ioctl download
input ioctl_download,
input ioctl_wr,
input [24:0] ioctl_addr,
input [7:0] ioctl_dout,
input [7:0] ioctl_index,
output ioctl_wait,
// MiSTer block device (VDNUM 7): 0-1 SDC, 2-5 floppy, 6 cassette write.
// Widths match SimBlockDevice's member types.
input [15:0] img_mounted,
input img_readonly,
input [63:0] img_size,
output [31:0] sd_lba [7],
output [15:0] sd_rd,
output [15:0] sd_wr,
input [15:0] sd_ack,
input [8:0] sd_buff_addr,
input [7:0] sd_buff_dout,
output [7:0] sd_buff_din [7],
input sd_buff_wr,
output [7:0] VGA_R,
output [7:0] VGA_G,
output [7:0] VGA_B,
output VGA_HS,
output VGA_VS,
output VGA_HB,
output VGA_VB,
output CE_PIXEL, // coco3fpga PIX_CLK: a clk_sys enable; sample RGB/syncs on a clk_sys rising edge when high
output [15:0] AUDIO_L,
output [15:0] AUDIO_R,
// RS-232 Pak (glb6551 at $FF68-$FF6B). On MiSTer these are the UART_* pins
// of the sys framework (the FujiNet daemon's /dev/ttyS1); here sim_main
// decodes TXD and drives RXD. Idle is 1.
output uart_txd,
input uart_rxd,
output uart_rts,
output uart_dtr,
// ---- debug taps ----------------------------------------------------
// Hierarchical reads into the core; nothing here drives it.
output [15:0] dbg_pc,
output [7:0] dbg_a, dbg_b, dbg_cc, dbg_dp,
output [15:0] dbg_x, dbg_y, dbg_u, dbg_s,
output dbg_lic, // last instruction cycle
output [15:0] dbg_addr,
output [7:0] dbg_din, // data into the CPU
output [7:0] dbg_dout, // data out of the CPU
output dbg_rw, // 1 = read
output dbg_ena, // cpu_cycle_ena: the CPU advances on this
output dbg_irqn,
output dbg_firqn,
output dbg_reset, // CPU_RESET
output [7:0] dbg_gime_init0, // $FF90
output [2:0] dbg_speed, // assigned_turbo_speed
// ACIA / Multi-Pak state, for the serial trace
output dbg_rs232_en, // $FF68-$FF6B decoded to the 6551 this cycle
output [1:0] dbg_mpi_scs, // $FF7F SCS (I/O slot, 0 = slot 1)
output [1:0] dbg_mpi_cts, // $FF7F CTS (ROM slot)
output [7:0] dbg_acia_ctl, // 6551 control register (baud in [3:0])
output [7:0] dbg_acia_cmd // 6551 command register
);
// The OSD word as the core sees it. hps_io hands `status` over as a register;
// registering it here too keeps it off the top-level input path. Verilator
// re-evaluates everything combinational on a top-level input at EVERY eval,
// and status feeds the video pixel mux (artifact/colour-set options), so as a
// raw input it cost ~20% of the run time.
reg [63:0] status_q = 64'd0;
always @(posedge CLK_14) status_q <= status;
//////////////////////////////////////////////////////////////////
// status decode -- copied from CoCo3.sv
//////////////////////////////////////////////////////////////////
wire clk_sys = CLK_57;
wire [2:0] turbo_speed = status_q[34:32];
wire [2:0] assigned_turbo_speed;
wire [1:0] art = status_q[38:37];
wire [1:0] Auto_Mode = status_q[41:40];
wire AMW_ACK;
wire [1:0] mpi = status_q[13:12] + 1'b1;
wire CASS_REW_RECORD = status_q[14];
wire rs_swap = status_q[16];
wire cartint = status_q[19];
wire sg4v6 = status_q[21];
wire PHASE = status_q[18];
wire coldboot = status_q[22];
wire F_Turbo = status_q[24];
wire [2:0] Mem_Size = status_q[27:25];
wire SWAP_M_J = status_q[28];
wire display_debug = status_q[29];
wire UART_INPUT = status_q[30];
wire digitalJoy = status_q[23];
wire easter_egg = status_q[10];
reg [2:0] mpi_d = 2'b00;
reg first_mpi_chg = 1'b0;
reg mpi_reset = 1'b0;
always @(negedge CLK_14) begin
mpi_d <= mpi;
mpi_reset <= 1'b0;
if (~(mpi == mpi_d))
if (~first_mpi_chg)
first_mpi_chg <= 1'b1;
else
mpi_reset <= 1'b1;
end
reg [2:0] Mem_Size_d = 3'b000;
reg first_mem_chg = 1'b0;
reg mem_reset = 1'b0;
always @(negedge CLK_14) begin
Mem_Size_d <= Mem_Size;
mem_reset <= 1'b0;
if (~(Mem_Size == Mem_Size_d))
if (~first_mem_chg)
first_mem_chg <= 1'b1;
else
mem_reset <= 1'b1;
end
// Set bit 9 to swap serial ports...
wire [9:0] switch = { cartint,UART_INPUT,art,sg4v6,rs_swap,CASS_REW_RECORD,mpi,1'b0};
wire reset = RESET | status_q[0] | buttons[1];
//////////////////////////////////////////////////////////////////
// Joysticks -- copied from CoCo3.sv
//////////////////////////////////////////////////////////////////
wire [9:0] center_joystick_y1 = 8'd128 + joya1[15:8];
wire [9:0] center_joystick_x1 = 8'd128 + joya1[7:0];
wire [9:0] center_joystick_y2 = 8'd128 + joya2[15:8];
wire [9:0] center_joystick_x2 = 8'd128 + joya2[7:0];
wire [31:0] coco_joy1 = status_q[6] ? joy2 : joy1;
wire [31:0] coco_joy2 = status_q[6] ? joy1 : joy2;
wire [15:0] coco_ajoy1 = status_q[6] ? {center_joystick_x2[7:0],center_joystick_y2[7:0]} : {center_joystick_x1[7:0],center_joystick_y1[7:0]};
wire [15:0] coco_ajoy2 = status_q[6] ? {center_joystick_x1[7:0],center_joystick_y1[7:0]} : {center_joystick_x2[7:0],center_joystick_y2[7:0]};
//////////////////////////////////////////////////////////////////
// Keyboard: ps2_key -> PS/2 serial, the way hps_io produces it
//////////////////////////////////////////////////////////////////
reg clk_ps2 = 1'b0;
reg [11:0] ps2_div = 12'd0;
always @(posedge clk_sys) begin
ps2_div <= ps2_div + 1'd1;
if (ps2_div == 12'd2400) begin // hps_io PS2DIV
clk_ps2 <= ~clk_ps2;
ps2_div <= 12'd0;
end
end
// One ps2_key event becomes [E0] [F0] code. Main_MiSTer hands hps_io the same
// bytes one at a time; here they go into ps2_device's FIFO on consecutive
// clk_sys cycles.
reg old_ps2_stb = 1'b0;
reg [1:0] kbd_seq = 2'd0;
reg kbd_ext, kbd_rel;
reg [7:0] kbd_code;
reg [7:0] kbd_data;
reg kbd_we = 1'b0;
always @(posedge clk_sys) begin
kbd_we <= 1'b0;
old_ps2_stb <= ps2_key[10];
if (kbd_seq == 2'd0 && old_ps2_stb != ps2_key[10]) begin
kbd_ext <= ps2_key[8];
kbd_rel <= ~ps2_key[9];
kbd_code <= ps2_key[7:0];
kbd_seq <= 2'd1;
end
else if (kbd_seq == 2'd1) begin
kbd_seq <= 2'd2;
if (kbd_ext) begin kbd_data <= 8'hE0; kbd_we <= 1'b1; end
end
else if (kbd_seq == 2'd2) begin
kbd_seq <= 2'd3;
if (kbd_rel) begin kbd_data <= 8'hF0; kbd_we <= 1'b1; end
end
else if (kbd_seq == 2'd3) begin
kbd_seq <= 2'd0;
kbd_data <= kbd_code;
kbd_we <= 1'b1;
end
end
wire ps2_kbd_clk;
wire ps2_kbd_data;
ps2_device keyboard
(
.clk_sys(clk_sys),
.wdata(kbd_data),
.we(kbd_we),
.ps2_clk(clk_ps2),
.ps2_clk_out(ps2_kbd_clk),
.ps2_dat_out(ps2_kbd_data),
.tx_empty(),
.ps2_clk_in(1'b1), // PS2WE=0: host never talks back
.ps2_dat_in(1'b1),
.rdata(),
.rd(1'b0)
);
//////////////////////////////////////////////////////////////////
// Core
//////////////////////////////////////////////////////////////////
wire Programmed_RESET_N;
wire Programmed_EE;
EE_Cold_Bt COCO3_EE_Cold_Bt (
.CLK(CLK_14),
.RESET(1'b0),
.Display_EE(easter_egg),
.Cold_Boot(AMW_ACK),
.RESET_to_COCO_N(Programmed_RESET_N),
.EE_to_COCO(Programmed_EE)
);
wire [15:0] audio_left;
wire [15:0] audio_right;
assign AUDIO_L = { audio_left[15:14], audio_left[13] ^ (status_q[17] ? casdout : 1'b0), audio_left[12:0]};
assign AUDIO_R = audio_right;
wire [7:0] r, g, b;
wire hblank, vblank, hs, vs, pix_clk;
wire [6:0] probe_o;
wire [71:0] Config_Data = {"SIMULATE", 8'h00};
wire [24:0] sdram_cpu_addr;
wire [15:0] sdram_dout;
wire [7:0] sdram_cpu_din;
wire sdram_cpu_req, sdram_cpu_rnw;
wire sdram_cpu_ack, sdram_vid_ack;
wire sdram_cpu_ready;
wire [24:0] sdram_vid_addr;
wire sdram_vid_req;
wire sdram_vid_ready;
wire sdram_busy;
wire [6:0] sd_rd_c, sd_wr_c;
wire [5:0] sd_blk_cnt [7];
assign sd_rd = {9'd0, sd_rd_c};
assign sd_wr = {9'd0, sd_wr_c};
wire clk_Q_out;
wire casdout;
wire cas_relay;
wire UART_TXD, UART_RTS, UART_DTR;
coco3fpga coco3 (
.CLK_50M(CLK_50M),
.CLK_114(CLK_114),
.CLK_57(CLK_57),
.CLK_28(CLK_28),
.CLK_14(CLK_14),
.COCO_RESET_N((~reset & Programmed_RESET_N)),
.RED_O(r),
.GREEN_O(g),
.BLUE_O(b),
.EE_N(Programmed_EE),
.PHASE(PHASE),
.H_SYNC(hs),
.V_SYNC(vs),
.HBLANK(hblank),
.VBLANK(vblank),
.PIX_CLK(pix_clk),
.ps2_clk(ps2_kbd_clk),
.ps2_data(ps2_kbd_data),
.ps2_mouse(ps2_mouse),
.joy_use_dpad(digitalJoy),
.joy1(coco_joy1[15:0]),
.joy2(coco_joy2[15:0]),
.joya1(coco_ajoy1),
.joya2(coco_ajoy2),
.SWAP_M_J(SWAP_M_J),
// R1, L2, R2, L1
.P_SWITCH(~{coco_joy2[4],coco_joy1[5],coco_joy2[5],coco_joy1[4]}),
.SWITCH(switch),
.SOUND_LEFT(audio_left),
.SOUND_RIGHT(audio_right),
.ioctl_addr(ioctl_addr),
.ioctl_data(ioctl_dout),
.ioctl_download(ioctl_download),
.ioctl_index({8'd0, ioctl_index}),
.ioctl_wr(ioctl_wr),
.sdram_sz(16'h8001), // SDRAM present, 32 MB
.img_mounted(img_mounted[6:0]),
.img_readonly(img_readonly),
.img_size(img_size),
.sd_lba(sd_lba),
.sd_blk_cnt(sd_blk_cnt),
.sd_rd(sd_rd_c),
.sd_wr(sd_wr_c),
.sd_ack(sd_ack[6:0]),
.sd_buff_addr(sd_buff_addr),
.sd_buff_dout(sd_buff_dout),
.sd_buff_din(sd_buff_din),
.sd_buff_wr(sd_buff_wr),
.GPIO(),
.PROBE_O(probe_o),
.PROBE_I(7'h7F), // SNAC (USER_IN) pins idle high
.clk_Q_out(clk_Q_out),
.casdout(casdout),
.cas_relay(cas_relay),
.sdram_cpu_addr(sdram_cpu_addr),
.sdram_dout(sdram_dout),
.sdram_cpu_din(sdram_cpu_din),
.sdram_cpu_req(sdram_cpu_req),
.sdram_cpu_rnw(sdram_cpu_rnw),
.sdram_cpu_ack(sdram_cpu_ack),
.sdram_cpu_ready(sdram_cpu_ready),
.sdram_vid_addr(sdram_vid_addr),
.sdram_vid_req(sdram_vid_req),
.sdram_vid_ack(sdram_vid_ack),
.sdram_vid_ready(sdram_vid_ready),
.sdram_busy(sdram_busy),
.turbo_speed(turbo_speed),
.assigned_turbo_speed(assigned_turbo_speed),
.RTC(RTC),
.AMW_Trigger(coldboot | mpi_reset | mem_reset),
.AMW_ACK(AMW_ACK),
.F_Turbo(F_Turbo),
.Mem_Size(Mem_Size),
.AUTO_MODE(Auto_Mode),
.Config_Data(Config_Data),
.Display_Debug(display_debug),
.UART_TXD(UART_TXD),
.UART_RXD(uart_rxd),
.UART_RTS(UART_RTS),
.UART_CTS(1'b0), // active low: always clear to send
.UART_DTR(UART_DTR),
.UART_DSR(1'b0)
);
sdram_32r8w coco3_sdram
(
.init(reset),
.clk(CLK_114),
.sdram_cpu_addr(sdram_cpu_addr),
.sdram_dout(sdram_dout),
.sdram_cpu_din(sdram_cpu_din),
.sdram_cpu_req(sdram_cpu_req),
.sdram_cpu_rnw(sdram_cpu_rnw),
.sdram_cpu_ack(sdram_cpu_ack),
.sdram_cpu_ready(sdram_cpu_ready),
.sdram_vid_addr(sdram_vid_addr),
.sdram_vid_req(sdram_vid_req),
.sdram_vid_ack(sdram_vid_ack),
.sdram_vid_ready(sdram_vid_ready),
.sdram_busy(sdram_busy)
);
//////////////////////////////////////////////////////////////////
// Cassette -- copied from CoCo3.sv
//////////////////////////////////////////////////////////////////
wire load_tape = ioctl_index == 2;
wire [15:0] ram_addr;
wire [7:0] ram_data_o;
reg ram_wr;
reg [15:0] ram_ad_buf;
always @(posedge clk_sys) begin
ram_wr <= ~(ioctl_wr & load_tape);
if (ioctl_download)
ram_ad_buf <= ioctl_addr[15:0];
else
ram_ad_buf <= ram_addr;
end
COCO_SRAM CC3_CAS1(
.CLK(clk_sys),
.ADDR(ram_ad_buf),
.R_W(ram_wr),
.DATA_I(ioctl_dout),
.DATA_O(ram_data_o)
);
cassette cassette(
.clk(clk_sys),
.Q(clk_Q_out),
.rewind(status_q[15]|~ram_wr),
.en(cas_relay),
.sdram_addr(ram_addr),
.sdram_data(ram_data_o),
.data(casdout)
);
assign ioctl_wait = 1'b0;
//////////////////////////////////////////////////////////////////
// Video out
//////////////////////////////////////////////////////////////////
assign VGA_R = r;
assign VGA_G = g;
assign VGA_B = b;
assign VGA_HS = hs;
assign VGA_VS = vs;
assign VGA_HB = hblank;
assign VGA_VB = vblank;
assign CE_PIXEL = pix_clk;
//////////////////////////////////////////////////////////////////
// Debug taps
//////////////////////////////////////////////////////////////////
assign dbg_pc = coco3.GLBCPU09.pc;
assign dbg_a = coco3.GLBCPU09.a;
assign dbg_b = coco3.GLBCPU09.b;
assign dbg_x = coco3.GLBCPU09.x;
assign dbg_y = coco3.GLBCPU09.y;
assign dbg_u = coco3.GLBCPU09.u;
assign dbg_s = coco3.GLBCPU09.s;
assign dbg_cc = coco3.GLBCPU09.cc;
assign dbg_dp = coco3.GLBCPU09.dp;
assign dbg_lic = coco3.GLBCPU09.LIC;
assign dbg_addr = coco3.ADDRESS;
assign dbg_din = coco3.DATA_IN;
assign dbg_dout = coco3.DATA_OUT;
assign dbg_rw = coco3.RW_N;
assign dbg_ena = coco3.cpu_cycle_ena;
assign dbg_irqn = coco3.CPU_IRQ_N;
assign dbg_firqn = coco3.CPU_FIRQ_N;
assign dbg_reset = coco3.CPU_RESET;
assign dbg_gime_init0 = {coco3.COCO1, coco3.MMU_EN, coco3.GIME_IRQ, coco3.GIME_FIRQ,
coco3.VEC_PAG_RAM, coco3.ST_SCS, coco3.ROM};
assign dbg_speed = assigned_turbo_speed;
assign uart_txd = UART_TXD;
assign uart_rts = UART_RTS;
assign uart_dtr = UART_DTR;
assign dbg_rs232_en = coco3.RS232_EN;
assign dbg_mpi_scs = coco3.MPI_SCS;
assign dbg_mpi_cts = coco3.MPI_CTS;
assign dbg_acia_ctl = coco3.RS232.CTL_REG;
assign dbg_acia_cmd = coco3.RS232.CMD_REG;
//////////////////////////////////////////////////////////////////
// FPGA power-up state
//
// Every register starts at 0 in this sim. Quartus does the same, EXCEPT for a
// register with an asynchronous set: it implements the set with NOT-gate
// push-back, so the register powers up at 1. Where that matters it is
// reproduced here.
//
// mc6809x NMILatched: active low (0 = NMI pending), in an
// `always @(negedge NMISample2 or posedge wNMIClear)` block whose async branch
// sets it. At 0 the CPU takes a phantom NMI on its first instruction -- the
// ORCC at the reset entry -- and vectors through $FFFC into uninitialised RAM.
//////////////////////////////////////////////////////////////////
initial coco3.GLBCPU09.NMILatched = 1'b1;
//////////////////////////////////////////////////////////////////
// +acia_any_slot (--acia-any-slot)
//
// coco3fpga.sv used to decode the RS-232 Pak at $FF68-$FF6B only when the
// Multi-Pak I/O select was slot 1 (MPI_SCS == 0), which the OSD cannot select,
// so a cart in slot 3 driving the 6551 -- HDB-DOS SY6551 for FujiNet -- talked
// to an empty bus. The RTL now decodes it in any slot, which makes this a no-op;
// it is kept for testing RTL from before that fix.
//////////////////////////////////////////////////////////////////
// The right-hand side of a procedural force is taken once, when the
// force executes (Verilator 5.044), so it is re-issued whenever the decode it follows
// changes. The net must also be `forceable` (sim.vlt) or the force is lost.
wire acia_any_slot_en = (coco3.ADDRESS[15:2] == 14'b11111111011010);
reg acia_any_slot = 1'b0;
initial acia_any_slot = $test$plusargs("acia_any_slot");
always @(acia_any_slot_en or acia_any_slot)
if (acia_any_slot) force coco3.RS232_EN = acia_any_slot_en;
endmodule
+4
View File
@@ -0,0 +1,4 @@
`verilator_config
// Nets sim.v overrides with `force` for --acia-any-slot. Without this Verilator
// folds RS232_EN into its users and the force has no effect.
forceable -module "coco3fpga" -var "RS232_EN"
File diff suppressed because it is too large. Load diff
File diff suppressed because it is too large. Load diff
@@ -0,0 +1,70 @@
#pragma once
// uncomment and modify defines under for customize ImGuiFileDialog
//#define MAX_FILE_DIALOG_NAME_BUFFER 1024
//#define MAX_PATH_BUFFER_SIZE 1024
//#define USE_EXPLORATION_BY_KEYS
// this mapping by default is for GLFW but you can use another
//#include <GLFW/glfw3.h>
// Up key for explore to the top
//#define IGFD_KEY_UP GLFW_KEY_UP
// Down key for explore to the bottom
//#define IGFD_KEY_DOWN GLFW_KEY_DOWN
// Enter key for open directory
//#define IGFD_KEY_ENTER GLFW_KEY_ENTER
// BackSpace for comming back to the last directory
//#define IGFD_KEY_BACKSPACE GLFW_KEY_BACKSPACE
// widget
// filter combobox width
//#define FILTER_COMBO_WIDTH 120.0f
// button widget use for compose path
//#define IMGUI_PATH_BUTTON ImGui::Button
// standard button
//#define IMGUI_BUTTON ImGui::Button
// locales string
//#define createDirButtonString "+"
//#define okButtonString " OK"
//#define cancelButtonString " Cancel"
//#define resetButtonString "R"
//#define drivesButtonString "Drives"
//#define searchString "Search"
//#define dirEntryString "[DIR] "
//#define linkEntryString "[LINK] "
//#define fileEntryString "[FILE] "
//#define fileNameString "File Name : "
//#define dirNameString "Directory Path :"
//#define buttonResetSearchString "Reset search"
//#define buttonDriveString "Drives"
//#define buttonResetPathString "Reset to current directory"
//#define buttonCreateDirString "Create Directory"
//#define OverWriteDialogTitleString "The file Already Exist !"
//#define OverWriteDialogMessageString "Would you like to OverWrite it ?"
//#define OverWriteDialogConfirmButtonString "Confirm"
//#define OverWriteDialogCancelButtonString "Cancel"
// DateTimeFormat
// see strftime functionin <ctime> for customize
// "%Y/%m/%d %H:%M" give 2021:01:22 11:47
// "%Y/%m/%d %i:%M%p" give 2021:01:22 11:45PM
//#define DateTimeFormat "%Y/%m/%d %i:%M%p"
// theses icons will appear in table headers
//#define USE_CUSTOM_SORTING_ICON
//#define tableHeaderAscendingIcon "A|"
//#define tableHeaderDescendingIcon "D|"
//#define tableHeaderFileNameString " File name"
//#define tableHeaderFileTypeString " Type"
//#define tableHeaderFileSizeString " Size"
//#define tableHeaderFileDateTimeString " Date"
//#define USE_BOOKMARK
//#define bookmarkPaneWith 150.0f
//#define IMGUI_TOGGLE_BUTTON ToggleButton
//#define bookmarksButtonString "Bookmark"
//#define bookmarksButtonHelpString "Bookmark"
//#define addBookmarkButtonString "+"
//#define removeBookmarkButtonString "-"
+21
View File
@@ -0,0 +1,21 @@
The MIT License (MIT)
Copyright (c) 2014-2022 Omar Cornut
Permission is hereby granted, free of charge, to any person obtaining a copy
of this software and associated documentation files (the "Software"), to deal
in the Software without restriction, including without limitation the rights
to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
copies of the Software, and to permit persons to whom the Software is
furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all
copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
+78
View File
@@ -0,0 +1,78 @@
#
# Cross Platform Makefile
# Compatible with MSYS2/MINGW, Ubuntu 14.04.1 and Mac OS X
#
# You will need SDL2 (http://www.libsdl.org):
# Linux:
# apt-get install libsdl2-dev
# Mac OS X:
# brew install sdl2
# MSYS2:
# pacman -S mingw-w64-i686-SDL
#
#CXX = g++
#CXX = clang++
EXE = example_sdl_opengl2
SOURCES = main.cpp
SOURCES += ../imgui_impl_sdl.cpp ../imgui_impl_opengl2.cpp
SOURCES += ../../imgui.cpp ../../imgui_demo.cpp ../../imgui_draw.cpp ../../imgui_widgets.cpp
OBJS = $(addsuffix .o, $(basename $(notdir $(SOURCES))))
UNAME_S := $(shell uname -s)
CXXFLAGS = -I../ -I../../
CXXFLAGS += -g -Wall -Wformat
LIBS =
##---------------------------------------------------------------------
## BUILD FLAGS PER PLATFORM
##---------------------------------------------------------------------
ifeq ($(UNAME_S), Linux) #LINUX
ECHO_MESSAGE = "Linux"
LIBS += -lGL -ldl `sdl2-config --libs`
CXXFLAGS += `sdl2-config --cflags`
CFLAGS = $(CXXFLAGS)
endif
ifeq ($(UNAME_S), Darwin) #APPLE
ECHO_MESSAGE = "Mac OS X"
LIBS += -framework OpenGL -framework Cocoa -framework IOKit -framework CoreVideo `sdl2-config --libs`
LIBS += -L/usr/local/lib -L/opt/local/lib
CXXFLAGS += `sdl2-config --cflags`
CXXFLAGS += -I/usr/local/include -I/opt/local/include
CFLAGS = $(CXXFLAGS)
endif
ifeq ($(findstring MINGW,$(UNAME_S)),MINGW)
ECHO_MESSAGE = "MinGW"
LIBS += -lgdi32 -lopengl32 -limm32 `pkg-config --static --libs sdl2`
CXXFLAGS += `pkg-config --cflags sdl2`
CFLAGS = $(CXXFLAGS)
endif
##---------------------------------------------------------------------
## BUILD RULES
##---------------------------------------------------------------------
%.o:%.cpp
$(CXX) $(CXXFLAGS) -c -o $@ $<
%.o:../%.cpp
$(CXX) $(CXXFLAGS) -c -o $@ $<
%.o:../../%.cpp
$(CXX) $(CXXFLAGS) -c -o $@ $<
all: $(EXE)
@echo Build complete for $(ECHO_MESSAGE)
$(EXE): $(OBJS)
$(CXX) -o $@ $^ $(CXXFLAGS) $(LIBS)
clean:
rm -f $(EXE) $(OBJS)
+129
View File
@@ -0,0 +1,129 @@
2018-05-08 Toni Rönkkö
* Version 1.23.2: fixes bad scandir prototype.
2017-08-27 Toni Rönkkö
* Version 1.23: support readdir_r and scandir functions.
2017-07-18 Toni Rönkkö
* Created release branches v1.22 and v1.21 to Git. Published version
1.22 at softagalleria.net.
2016-09-11 Toni Rönkkö
* Version 1.22: added support for CMake. Thanks to Paul Fultz II.
2014-09-25 Toni Rönkkö
* Version 1.21: compiles correctly under Open Watcom. Thanks to
Virgil Banowetz for a patch!
2014-04-07 Toni Rönkkö
* Version 1.20.1: the zip file from the previous version did not open
correctly with Microsoft's compressed folders. Thanks to Alexandre
for info!
2014-03-17 Toni Ronkko
* Version 1.20: dirent.h compiles correctly in 64-bit architecture.
Thanks to Aaron Simmons!
2014-03-03 Toni Ronkko
* Version 1.13.2: define DT_LNK for compatibility with Unix
programs. Thanks to Joel Bruick for suggestion!
2013-01-27 Toni Ronkko
* Version 1.13.1: patch from Edward Berner fixes set_errno() on
Windows NT 4.0.
* Revised wcstombs() and mbstowcs() wrappers to make sure that they do
not write past their target string.
* PATH_MAX from windows.h includes zero terminator so there is no
need to add one extra byte to variables and structures.
2012-12-12 Toni Ronkko
* Version 1.13: use the traditional 8+3 file naming scheme if a file
name cannot be represented in the default ANSI code page. Now
compiles again with MSVC 6.0. Thanks to Konstantin Khomoutov for
testing.
2012-10-01 Toni Ronkko
* Version 1.12.1: renamed wide-character DIR structure _wDIR to
_WDIR (with capital W) in order to maintain compatibility with MingW.
2012-09-30 Toni Ronkko
* Version 1.12: define PATH_MAX and NAME_MAX. Added wide-character
variants _wDIR, _wdirent, _wopendir(), _wreaddir(), _wclosedir() and
_wrewinddir(). Thanks to Edgar Buerkle and Jan Nijtmans for ideas
and code.
* Now avoiding windows.h. This allows dirent.h to be integrated
more easily into programs using winsock. Thanks to Fernando
Azaldegui.
2011-03-15 Toni Ronkko
* Version 1.11: defined FILE_ATTRIBUTE_DEVICE for MSVC 6.0.
2010-08-11 Toni Ronkko
* Version 1.10: added d_type and d_namlen fields to dirent structure.
The former is especially useful for determining whether directory
entry represents a file or a directory. For more information, see
http://www.delorie.com/gnu/docs/glibc/libc_270.html
* Improved conformance to the standards. For example, errno is now
set properly on failure and assert() is never used. Thanks to Peter
Brockam for suggestions.
* Fixed a bug in rewinddir(): when using relative directory names,
change of working directory no longer causes rewinddir() to fail.
2009-12-15 John Cunningham
* Version 1.9: added rewinddir member function
2008-01-18 Toni Ronkko
* Version 1.8: Using FindFirstFileA and WIN32_FIND_DATAA to avoid
converting string between multi-byte and unicode representations.
This makes the code simpler and also allows the code to be compiled
under MingW. Thanks to Azriel Fasten for the suggestion.
2007-03-04 Toni Ronkko
* Bug fix: due to the strncpy_s() function this file only compiled in
Visual Studio 2005. Using the new string functions only when the
compiler version allows.
2006-11-02 Toni Ronkko
* Major update: removed support for Watcom C, MS-DOS and Turbo C to
simplify the file, updated the code to compile cleanly on Visual
Studio 2005 with both unicode and multi-byte character strings,
removed rewinddir() as it had a bug.
2006-08-20 Toni Ronkko
* Removed all remarks about MSVC 1.0, which is antiqued now.
Simplified comments by removing SGML tags.
2002-05-14 Toni Ronkko
* Embedded the function definitions directly to the header so that no
source modules need to be included in the Visual Studio project.
Removed all the dependencies to other projects so that this header
file can be used independently.
1998-05-28 Toni Ronkko
* First version.
+21
View File
@@ -0,0 +1,21 @@
The MIT License (MIT)
Copyright (c) 1998-2019 Toni Ronkko
Permission is hereby granted, free of charge, to any person obtaining a copy
of this software and associated documentation files (the "Software"), to deal
in the Software without restriction, including without limitation the rights
to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
copies of the Software, and to permit persons to whom the Software is
furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all
copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
+96
View File
@@ -0,0 +1,96 @@
# Dirent
Dirent is a C/C++ programming interface that allows programmers to retrieve
information about files and directories under Linux/UNIX. This project
provides Linux compatible Dirent interface for Microsoft Windows.
# Installation
Download the latest Dirent installation package from
[GitHub](https://github.com/tronkko/dirent/releases) and
unpack the installation file with 7-zip, for example. The installation
package contains dirent.h file as well as a few example programs and
tests.
## Install Dirent for All Programs
To make dirent.h available for all C/C++ programs, simply copy the
``include/dirent.h`` file to the system include directory. System include
directory contains header files such as assert.h and windows.h. In Visual
Studio 2008, for example, the system include may be found at
``C:\Program Files\Microsoft Visual Studio 9.0\VC\include``.
Everything you need is included in the single dirent.h file, and you can
start using Dirent immediately -- there is no need to add files to your
Visual Studio project.
## Embed Dirent into Your Own Project
If you wish to distribute dirent.h alongside with your own source code, then
copy ``include/dirent.h`` file to a new sub-directory within your project and
add that directory to include path on Windows while omitting the directory
under Linux/UNIX. This allows your project to be compiled against native
dirent.h on Linux/UNIX while substituting the functionality on Microsoft
Windows.
## Examples
The installation package contains four example programs:
Program | Purpose
-------- | -----------------------------------------------------------------
ls | List files in a directory, e.g. ls "c:\Program Files"
find | Find files in subdirectories, e.g. find "c:\Program Files\CMake"
updatedb | Build database of files in a drive, e.g. updatedb c:\
locate | Locate a file from database, e.g. locate notepad.exe
To build the example programs, first install [CMake](https://cmake.org/).
Then, with CMake installed, open command prompt and create a temporary
directory ``c:\temp\dirent`` for the build files as
```
c:\
mkdir temp
mkdir temp\dirent
cd temp\dirent
```
Generate build files as
```
cmake d:\dirent
```
where ``d:\dirent`` is the root directory of the Dirent package (containing
this README.md and LICENSE file).
Once CMake is finished, open Visual Studio, load the generated dirent.sln file
from the build directory and build the solution. Once the build completes, run
the example programs from the command prompt as
```
cd Debug
ls .
find .
updatedb c:\
locate cmd.exe
```
# Copying
Dirent may be freely distributed under the MIT license. See the
[LICENSE](LICENSE) file for details.
# Alternatives to Dirent
I ported Dirent to Microsoft Windows in 1998 when only a few alternatives
were available. However, the situation has changed since then and nowadays
both [Cygwin](http://www.cygwin.com) and [MingW](http://www.mingw.org)
allow you to compile a great number of UNIX programs in Microsoft Windows.
They both provide a full dirent API as well as many other UNIX APIs. MingW
can even be used for commercial applications!
File diff suppressed because it is too large. Load diff
+124
View File
@@ -0,0 +1,124 @@
//-----------------------------------------------------------------------------
// COMPILE-TIME OPTIONS FOR DEAR IMGUI
// Runtime options (clipboard callbacks, enabling various features, etc.) can generally be set via the ImGuiIO structure.
// You can use ImGui::SetAllocatorFunctions() before calling ImGui::CreateContext() to rewire memory allocation functions.
//-----------------------------------------------------------------------------
// A) You may edit imconfig.h (and not overwrite it when updating Dear ImGui, or maintain a patch/rebased branch with your modifications to it)
// B) or '#define IMGUI_USER_CONFIG "my_imgui_config.h"' in your project and then add directives in your own file without touching this template.
//-----------------------------------------------------------------------------
// You need to make sure that configuration settings are defined consistently _everywhere_ Dear ImGui is used, which include the imgui*.cpp
// files but also _any_ of your code that uses Dear ImGui. This is because some compile-time options have an affect on data structures.
// Defining those options in imconfig.h will ensure every compilation unit gets to see the same data structure layouts.
// Call IMGUI_CHECKVERSION() from your .cpp files to verify that the data structures your files are using are matching the ones imgui.cpp is using.
//-----------------------------------------------------------------------------
#pragma once
//---- Define assertion handler. Defaults to calling assert().
// If your macro uses multiple statements, make sure is enclosed in a 'do { .. } while (0)' block so it can be used as a single statement.
//#define IM_ASSERT(_EXPR) MyAssert(_EXPR)
//#define IM_ASSERT(_EXPR) ((void)(_EXPR)) // Disable asserts
//---- Define attributes of all API symbols declarations, e.g. for DLL under Windows
// Using Dear ImGui via a shared library is not recommended, because of function call overhead and because we don't guarantee backward nor forward ABI compatibility.
// DLL users: heaps and globals are not shared across DLL boundaries! You will need to call SetCurrentContext() + SetAllocatorFunctions()
// for each static/DLL boundary you are calling from. Read "Context and Memory Allocators" section of imgui.cpp for more details.
//#define IMGUI_API __declspec( dllexport )
//#define IMGUI_API __declspec( dllimport )
//---- Don't define obsolete functions/enums/behaviors. Consider enabling from time to time after updating to avoid using soon-to-be obsolete function/names.
//#define IMGUI_DISABLE_OBSOLETE_FUNCTIONS
//#define IMGUI_DISABLE_OBSOLETE_KEYIO // 1.87: disable legacy io.KeyMap[]+io.KeysDown[] in favor io.AddKeyEvent(). This will be folded into IMGUI_DISABLE_OBSOLETE_FUNCTIONS in a few versions.
//---- Disable all of Dear ImGui or don't implement standard windows.
// It is very strongly recommended to NOT disable the demo windows during development. Please read comments in imgui_demo.cpp.
//#define IMGUI_DISABLE // Disable everything: all headers and source files will be empty.
//#define IMGUI_DISABLE_DEMO_WINDOWS // Disable demo windows: ShowDemoWindow()/ShowStyleEditor() will be empty. Not recommended.
//#define IMGUI_DISABLE_METRICS_WINDOW // Disable metrics/debugger and other debug tools: ShowMetricsWindow() and ShowStackToolWindow() will be empty.
//---- Don't implement some functions to reduce linkage requirements.
//#define IMGUI_DISABLE_WIN32_DEFAULT_CLIPBOARD_FUNCTIONS // [Win32] Don't implement default clipboard handler. Won't use and link with OpenClipboard/GetClipboardData/CloseClipboard etc. (user32.lib/.a, kernel32.lib/.a)
//#define IMGUI_ENABLE_WIN32_DEFAULT_IME_FUNCTIONS // [Win32] [Default with Visual Studio] Implement default IME handler (require imm32.lib/.a, auto-link for Visual Studio, -limm32 on command-line for MinGW)
//#define IMGUI_DISABLE_WIN32_DEFAULT_IME_FUNCTIONS // [Win32] [Default with non-Visual Studio compilers] Don't implement default IME handler (won't require imm32.lib/.a)
//#define IMGUI_DISABLE_WIN32_FUNCTIONS // [Win32] Won't use and link with any Win32 function (clipboard, ime).
//#define IMGUI_ENABLE_OSX_DEFAULT_CLIPBOARD_FUNCTIONS // [OSX] Implement default OSX clipboard handler (need to link with '-framework ApplicationServices', this is why this is not the default).
//#define IMGUI_DISABLE_DEFAULT_FORMAT_FUNCTIONS // Don't implement ImFormatString/ImFormatStringV so you can implement them yourself (e.g. if you don't want to link with vsnprintf)
//#define IMGUI_DISABLE_DEFAULT_MATH_FUNCTIONS // Don't implement ImFabs/ImSqrt/ImPow/ImFmod/ImCos/ImSin/ImAcos/ImAtan2 so you can implement them yourself.
//#define IMGUI_DISABLE_FILE_FUNCTIONS // Don't implement ImFileOpen/ImFileClose/ImFileRead/ImFileWrite and ImFileHandle at all (replace them with dummies)
//#define IMGUI_DISABLE_DEFAULT_FILE_FUNCTIONS // Don't implement ImFileOpen/ImFileClose/ImFileRead/ImFileWrite and ImFileHandle so you can implement them yourself if you don't want to link with fopen/fclose/fread/fwrite. This will also disable the LogToTTY() function.
//#define IMGUI_DISABLE_DEFAULT_ALLOCATORS // Don't implement default allocators calling malloc()/free() to avoid linking with them. You will need to call ImGui::SetAllocatorFunctions().
//#define IMGUI_DISABLE_SSE // Disable use of SSE intrinsics even if available
//---- Include imgui_user.h at the end of imgui.h as a convenience
//#define IMGUI_INCLUDE_IMGUI_USER_H
//---- Pack colors to BGRA8 instead of RGBA8 (to avoid converting from one to another)
//#define IMGUI_USE_BGRA_PACKED_COLOR
//---- Use 32-bit for ImWchar (default is 16-bit) to support unicode planes 1-16. (e.g. point beyond 0xFFFF like emoticons, dingbats, symbols, shapes, ancient languages, etc...)
//#define IMGUI_USE_WCHAR32
//---- Avoid multiple STB libraries implementations, or redefine path/filenames to prioritize another version
// By default the embedded implementations are declared static and not available outside of Dear ImGui sources files.
//#define IMGUI_STB_TRUETYPE_FILENAME "my_folder/stb_truetype.h"
//#define IMGUI_STB_RECT_PACK_FILENAME "my_folder/stb_rect_pack.h"
//#define IMGUI_DISABLE_STB_TRUETYPE_IMPLEMENTATION
//#define IMGUI_DISABLE_STB_RECT_PACK_IMPLEMENTATION
//---- Use stb_printf's faster implementation of vsnprintf instead of the one from libc (unless IMGUI_DISABLE_DEFAULT_FORMAT_FUNCTIONS is defined)
// Requires 'stb_sprintf.h' to be available in the include path. Compatibility checks of arguments and formats done by clang and GCC will be disabled in order to support the extra formats provided by STB sprintf.
// #define IMGUI_USE_STB_SPRINTF
//---- Use FreeType to build and rasterize the font atlas (instead of stb_truetype which is embedded by default in Dear ImGui)
// Requires FreeType headers to be available in the include path. Requires program to be compiled with 'misc/freetype/imgui_freetype.cpp' (in this repository) + the FreeType library (not provided).
// On Windows you may use vcpkg with 'vcpkg install freetype --triplet=x64-windows' + 'vcpkg integrate install'.
//#define IMGUI_ENABLE_FREETYPE
//---- Use stb_truetype to build and rasterize the font atlas (default)
// The only purpose of this define is if you want force compilation of the stb_truetype backend ALONG with the FreeType backend.
//#define IMGUI_ENABLE_STB_TRUETYPE
//---- Define constructor and implicit cast operators to convert back<>forth between your math types and ImVec2/ImVec4.
// This will be inlined as part of ImVec2 and ImVec4 class declarations.
/*
#define IM_VEC2_CLASS_EXTRA \
ImVec2(const MyVec2& f) { x = f.x; y = f.y; } \
operator MyVec2() const { return MyVec2(x,y); }
#define IM_VEC4_CLASS_EXTRA \
ImVec4(const MyVec4& f) { x = f.x; y = f.y; z = f.z; w = f.w; } \
operator MyVec4() const { return MyVec4(x,y,z,w); }
*/
//---- Use 32-bit vertex indices (default is 16-bit) is one way to allow large meshes with more than 64K vertices.
// Your renderer backend will need to support it (most example renderer backends support both 16/32-bit indices).
// Another way to allow large meshes while keeping 16-bit indices is to handle ImDrawCmd::VtxOffset in your renderer.
// Read about ImGuiBackendFlags_RendererHasVtxOffset for details.
//#define ImDrawIdx unsigned int
//---- Override ImDrawCallback signature (will need to modify renderer backends accordingly)
//struct ImDrawList;
//struct ImDrawCmd;
//typedef void (*MyImDrawCallback)(const ImDrawList* draw_list, const ImDrawCmd* cmd, void* my_renderer_user_data);
//#define ImDrawCallback MyImDrawCallback
//---- Debug Tools: Macro to break in Debugger
// (use 'Metrics->Tools->Item Picker' to pick widgets with the mouse and break into them for easy debugging.)
//#define IM_DEBUG_BREAK IM_ASSERT(0)
//#define IM_DEBUG_BREAK __debugbreak()
//---- Debug Tools: Have the Item Picker break in the ItemAdd() function instead of ItemHoverable(),
// (which comes earlier in the code, will catch a few extra items, allow picking items other than Hovered one.)
// This adds a small runtime cost which is why it is not enabled by default.
//#define IMGUI_DEBUG_TOOL_ITEM_PICKER_EX
//---- Debug Tools: Enable slower asserts
//#define IMGUI_DEBUG_PARANOID
//---- Tip: You can add extra functions within the ImGui:: namespace, here or in your own headers files.
/*
namespace ImGui
{
void MyFunction(const char* name, const MyMatrix44& v);
}
*/
File diff suppressed because it is too large. Load diff
File diff suppressed because it is too large. Load diff
File diff suppressed because it is too large. Load diff
File diff suppressed because it is too large. Load diff
+594
View File
@@ -0,0 +1,594 @@
// dear imgui: Renderer Backend for DirectX11
// This needs to be used along with a Platform Backend (e.g. Win32)
// Implemented features:
// [X] Renderer: User texture binding. Use 'ID3D11ShaderResourceView*' as ImTextureID. Read the FAQ about ImTextureID!
// [X] Renderer: Support for large meshes (64k+ vertices) with 16-bit indices.
// You can use unmodified imgui_impl_* files in your project. See examples/ folder for examples of using this.
// Prefer including the entire imgui/ repository into your project (either as a copy or as a submodule), and only build the backends you need.
// If you are new to Dear ImGui, read documentation from the docs/ folder + read the top of imgui.cpp.
// Read online: https://github.com/ocornut/imgui/tree/master/docs
// CHANGELOG
// (minor and older changes stripped away, please see git history for details)
// 2021-06-29: Reorganized backend to pull data from a single structure to facilitate usage with multiple-contexts (all g_XXXX access changed to bd->XXXX).
// 2021-05-19: DirectX11: Replaced direct access to ImDrawCmd::TextureId with a call to ImDrawCmd::GetTexID(). (will become a requirement)
// 2021-02-18: DirectX11: Change blending equation to preserve alpha in output buffer.
// 2019-08-01: DirectX11: Fixed code querying the Geometry Shader state (would generally error with Debug layer enabled).
// 2019-07-21: DirectX11: Backup, clear and restore Geometry Shader is any is bound when calling ImGui_ImplDX10_RenderDrawData. Clearing Hull/Domain/Compute shaders without backup/restore.
// 2019-05-29: DirectX11: Added support for large mesh (64K+ vertices), enable ImGuiBackendFlags_RendererHasVtxOffset flag.
// 2019-04-30: DirectX11: Added support for special ImDrawCallback_ResetRenderState callback to reset render state.
// 2018-12-03: Misc: Added #pragma comment statement to automatically link with d3dcompiler.lib when using D3DCompile().
// 2018-11-30: Misc: Setting up io.BackendRendererName so it can be displayed in the About Window.
// 2018-08-01: DirectX11: Querying for IDXGIFactory instead of IDXGIFactory1 to increase compatibility.
// 2018-07-13: DirectX11: Fixed unreleased resources in Init and Shutdown functions.
// 2018-06-08: Misc: Extracted imgui_impl_dx11.cpp/.h away from the old combined DX11+Win32 example.
// 2018-06-08: DirectX11: Use draw_data->DisplayPos and draw_data->DisplaySize to setup projection matrix and clipping rectangle.
// 2018-02-16: Misc: Obsoleted the io.RenderDrawListsFn callback and exposed ImGui_ImplDX11_RenderDrawData() in the .h file so you can call it yourself.
// 2018-02-06: Misc: Removed call to ImGui::Shutdown() which is not available from 1.60 WIP, user needs to call CreateContext/DestroyContext themselves.
// 2016-05-07: DirectX11: Disabling depth-write.
#include "imgui.h"
#include "imgui_impl_dx11.h"
// DirectX
#include <stdio.h>
#include <d3d11.h>
#include <d3dcompiler.h>
#ifdef _MSC_VER
#pragma comment(lib, "d3dcompiler") // Automatically link with d3dcompiler.lib as we are using D3DCompile() below.
#endif
// DirectX11 data
struct ImGui_ImplDX11_Data
{
ID3D11Device* pd3dDevice;
ID3D11DeviceContext* pd3dDeviceContext;
IDXGIFactory* pFactory;
ID3D11Buffer* pVB;
ID3D11Buffer* pIB;
ID3D11VertexShader* pVertexShader;
ID3D11InputLayout* pInputLayout;
ID3D11Buffer* pVertexConstantBuffer;
ID3D11PixelShader* pPixelShader;
ID3D11SamplerState* pFontSampler;
ID3D11ShaderResourceView* pFontTextureView;
ID3D11RasterizerState* pRasterizerState;
ID3D11BlendState* pBlendState;
ID3D11DepthStencilState* pDepthStencilState;
int VertexBufferSize;
int IndexBufferSize;
ImGui_ImplDX11_Data() { memset(this, 0, sizeof(*this)); VertexBufferSize = 5000; IndexBufferSize = 10000; }
};
struct VERTEX_CONSTANT_BUFFER
{
float mvp[4][4];
};
// Backend data stored in io.BackendRendererUserData to allow support for multiple Dear ImGui contexts
// It is STRONGLY preferred that you use docking branch with multi-viewports (== single Dear ImGui context + multiple windows) instead of multiple Dear ImGui contexts.
static ImGui_ImplDX11_Data* ImGui_ImplDX11_GetBackendData()
{
return ImGui::GetCurrentContext() ? (ImGui_ImplDX11_Data*)ImGui::GetIO().BackendRendererUserData : NULL;
}
// Functions
static void ImGui_ImplDX11_SetupRenderState(ImDrawData* draw_data, ID3D11DeviceContext* ctx)
{
ImGui_ImplDX11_Data* bd = ImGui_ImplDX11_GetBackendData();
// Setup viewport
D3D11_VIEWPORT vp;
memset(&vp, 0, sizeof(D3D11_VIEWPORT));
vp.Width = draw_data->DisplaySize.x;
vp.Height = draw_data->DisplaySize.y;
vp.MinDepth = 0.0f;
vp.MaxDepth = 1.0f;
vp.TopLeftX = vp.TopLeftY = 0;
ctx->RSSetViewports(1, &vp);
// Setup shader and vertex buffers
unsigned int stride = sizeof(ImDrawVert);
unsigned int offset = 0;
ctx->IASetInputLayout(bd->pInputLayout);
ctx->IASetVertexBuffers(0, 1, &bd->pVB, &stride, &offset);
ctx->IASetIndexBuffer(bd->pIB, sizeof(ImDrawIdx) == 2 ? DXGI_FORMAT_R16_UINT : DXGI_FORMAT_R32_UINT, 0);
ctx->IASetPrimitiveTopology(D3D11_PRIMITIVE_TOPOLOGY_TRIANGLELIST);
ctx->VSSetShader(bd->pVertexShader, NULL, 0);
ctx->VSSetConstantBuffers(0, 1, &bd->pVertexConstantBuffer);
ctx->PSSetShader(bd->pPixelShader, NULL, 0);
ctx->PSSetSamplers(0, 1, &bd->pFontSampler);
ctx->GSSetShader(NULL, NULL, 0);
ctx->HSSetShader(NULL, NULL, 0); // In theory we should backup and restore this as well.. very infrequently used..
ctx->DSSetShader(NULL, NULL, 0); // In theory we should backup and restore this as well.. very infrequently used..
ctx->CSSetShader(NULL, NULL, 0); // In theory we should backup and restore this as well.. very infrequently used..
// Setup blend state
const float blend_factor[4] = { 0.f, 0.f, 0.f, 0.f };
ctx->OMSetBlendState(bd->pBlendState, blend_factor, 0xffffffff);
ctx->OMSetDepthStencilState(bd->pDepthStencilState, 0);
ctx->RSSetState(bd->pRasterizerState);
}
// Render function
void ImGui_ImplDX11_RenderDrawData(ImDrawData* draw_data)
{
// Avoid rendering when minimized
if (draw_data->DisplaySize.x <= 0.0f || draw_data->DisplaySize.y <= 0.0f)
return;
ImGui_ImplDX11_Data* bd = ImGui_ImplDX11_GetBackendData();
ID3D11DeviceContext* ctx = bd->pd3dDeviceContext;
// Create and grow vertex/index buffers if needed
if (!bd->pVB || bd->VertexBufferSize < draw_data->TotalVtxCount)
{
if (bd->pVB) { bd->pVB->Release(); bd->pVB = NULL; }
bd->VertexBufferSize = draw_data->TotalVtxCount + 5000;
D3D11_BUFFER_DESC desc;
memset(&desc, 0, sizeof(D3D11_BUFFER_DESC));
desc.Usage = D3D11_USAGE_DYNAMIC;
desc.ByteWidth = bd->VertexBufferSize * sizeof(ImDrawVert);
desc.BindFlags = D3D11_BIND_VERTEX_BUFFER;
desc.CPUAccessFlags = D3D11_CPU_ACCESS_WRITE;
desc.MiscFlags = 0;
if (bd->pd3dDevice->CreateBuffer(&desc, NULL, &bd->pVB) < 0)
return;
}
if (!bd->pIB || bd->IndexBufferSize < draw_data->TotalIdxCount)
{
if (bd->pIB) { bd->pIB->Release(); bd->pIB = NULL; }
bd->IndexBufferSize = draw_data->TotalIdxCount + 10000;
D3D11_BUFFER_DESC desc;
memset(&desc, 0, sizeof(D3D11_BUFFER_DESC));
desc.Usage = D3D11_USAGE_DYNAMIC;
desc.ByteWidth = bd->IndexBufferSize * sizeof(ImDrawIdx);
desc.BindFlags = D3D11_BIND_INDEX_BUFFER;
desc.CPUAccessFlags = D3D11_CPU_ACCESS_WRITE;
if (bd->pd3dDevice->CreateBuffer(&desc, NULL, &bd->pIB) < 0)
return;
}
// Upload vertex/index data into a single contiguous GPU buffer
D3D11_MAPPED_SUBRESOURCE vtx_resource, idx_resource;
if (ctx->Map(bd->pVB, 0, D3D11_MAP_WRITE_DISCARD, 0, &vtx_resource) != S_OK)
return;
if (ctx->Map(bd->pIB, 0, D3D11_MAP_WRITE_DISCARD, 0, &idx_resource) != S_OK)
return;
ImDrawVert* vtx_dst = (ImDrawVert*)vtx_resource.pData;
ImDrawIdx* idx_dst = (ImDrawIdx*)idx_resource.pData;
for (int n = 0; n < draw_data->CmdListsCount; n++)
{
const ImDrawList* cmd_list = draw_data->CmdLists[n];
memcpy(vtx_dst, cmd_list->VtxBuffer.Data, cmd_list->VtxBuffer.Size * sizeof(ImDrawVert));
memcpy(idx_dst, cmd_list->IdxBuffer.Data, cmd_list->IdxBuffer.Size * sizeof(ImDrawIdx));
vtx_dst += cmd_list->VtxBuffer.Size;
idx_dst += cmd_list->IdxBuffer.Size;
}
ctx->Unmap(bd->pVB, 0);
ctx->Unmap(bd->pIB, 0);
// Setup orthographic projection matrix into our constant buffer
// Our visible imgui space lies from draw_data->DisplayPos (top left) to draw_data->DisplayPos+data_data->DisplaySize (bottom right). DisplayPos is (0,0) for single viewport apps.
{
D3D11_MAPPED_SUBRESOURCE mapped_resource;
if (ctx->Map(bd->pVertexConstantBuffer, 0, D3D11_MAP_WRITE_DISCARD, 0, &mapped_resource) != S_OK)
return;
VERTEX_CONSTANT_BUFFER* constant_buffer = (VERTEX_CONSTANT_BUFFER*)mapped_resource.pData;
float L = draw_data->DisplayPos.x;
float R = draw_data->DisplayPos.x + draw_data->DisplaySize.x;
float T = draw_data->DisplayPos.y;
float B = draw_data->DisplayPos.y + draw_data->DisplaySize.y;
float mvp[4][4] =
{
{ 2.0f/(R-L), 0.0f, 0.0f, 0.0f },
{ 0.0f, 2.0f/(T-B), 0.0f, 0.0f },
{ 0.0f, 0.0f, 0.5f, 0.0f },
{ (R+L)/(L-R), (T+B)/(B-T), 0.5f, 1.0f },
};
memcpy(&constant_buffer->mvp, mvp, sizeof(mvp));
ctx->Unmap(bd->pVertexConstantBuffer, 0);
}
// Backup DX state that will be modified to restore it afterwards (unfortunately this is very ugly looking and verbose. Close your eyes!)
struct BACKUP_DX11_STATE
{
UINT ScissorRectsCount, ViewportsCount;
D3D11_RECT ScissorRects[D3D11_VIEWPORT_AND_SCISSORRECT_OBJECT_COUNT_PER_PIPELINE];
D3D11_VIEWPORT Viewports[D3D11_VIEWPORT_AND_SCISSORRECT_OBJECT_COUNT_PER_PIPELINE];
ID3D11RasterizerState* RS;
ID3D11BlendState* BlendState;
FLOAT BlendFactor[4];
UINT SampleMask;
UINT StencilRef;
ID3D11DepthStencilState* DepthStencilState;
ID3D11ShaderResourceView* PSShaderResource;
ID3D11SamplerState* PSSampler;
ID3D11PixelShader* PS;
ID3D11VertexShader* VS;
ID3D11GeometryShader* GS;
UINT PSInstancesCount, VSInstancesCount, GSInstancesCount;
ID3D11ClassInstance *PSInstances[256], *VSInstances[256], *GSInstances[256]; // 256 is max according to PSSetShader documentation
D3D11_PRIMITIVE_TOPOLOGY PrimitiveTopology;
ID3D11Buffer* IndexBuffer, *VertexBuffer, *VSConstantBuffer;
UINT IndexBufferOffset, VertexBufferStride, VertexBufferOffset;
DXGI_FORMAT IndexBufferFormat;
ID3D11InputLayout* InputLayout;
};
BACKUP_DX11_STATE old = {};
old.ScissorRectsCount = old.ViewportsCount = D3D11_VIEWPORT_AND_SCISSORRECT_OBJECT_COUNT_PER_PIPELINE;
ctx->RSGetScissorRects(&old.ScissorRectsCount, old.ScissorRects);
ctx->RSGetViewports(&old.ViewportsCount, old.Viewports);
ctx->RSGetState(&old.RS);
ctx->OMGetBlendState(&old.BlendState, old.BlendFactor, &old.SampleMask);
ctx->OMGetDepthStencilState(&old.DepthStencilState, &old.StencilRef);
ctx->PSGetShaderResources(0, 1, &old.PSShaderResource);
ctx->PSGetSamplers(0, 1, &old.PSSampler);
old.PSInstancesCount = old.VSInstancesCount = old.GSInstancesCount = 256;
ctx->PSGetShader(&old.PS, old.PSInstances, &old.PSInstancesCount);
ctx->VSGetShader(&old.VS, old.VSInstances, &old.VSInstancesCount);
ctx->VSGetConstantBuffers(0, 1, &old.VSConstantBuffer);
ctx->GSGetShader(&old.GS, old.GSInstances, &old.GSInstancesCount);
ctx->IAGetPrimitiveTopology(&old.PrimitiveTopology);
ctx->IAGetIndexBuffer(&old.IndexBuffer, &old.IndexBufferFormat, &old.IndexBufferOffset);
ctx->IAGetVertexBuffers(0, 1, &old.VertexBuffer, &old.VertexBufferStride, &old.VertexBufferOffset);
ctx->IAGetInputLayout(&old.InputLayout);
// Setup desired DX state
ImGui_ImplDX11_SetupRenderState(draw_data, ctx);
// Render command lists
// (Because we merged all buffers into a single one, we maintain our own offset into them)
int global_idx_offset = 0;
int global_vtx_offset = 0;
ImVec2 clip_off = draw_data->DisplayPos;
for (int n = 0; n < draw_data->CmdListsCount; n++)
{
const ImDrawList* cmd_list = draw_data->CmdLists[n];
for (int cmd_i = 0; cmd_i < cmd_list->CmdBuffer.Size; cmd_i++)
{
const ImDrawCmd* pcmd = &cmd_list->CmdBuffer[cmd_i];
if (pcmd->UserCallback != NULL)
{
// User callback, registered via ImDrawList::AddCallback()
// (ImDrawCallback_ResetRenderState is a special callback value used by the user to request the renderer to reset render state.)
if (pcmd->UserCallback == ImDrawCallback_ResetRenderState)
ImGui_ImplDX11_SetupRenderState(draw_data, ctx);
else
pcmd->UserCallback(cmd_list, pcmd);
}
else
{
// Project scissor/clipping rectangles into framebuffer space
ImVec2 clip_min(pcmd->ClipRect.x - clip_off.x, pcmd->ClipRect.y - clip_off.y);
ImVec2 clip_max(pcmd->ClipRect.z - clip_off.x, pcmd->ClipRect.w - clip_off.y);
if (clip_max.x <= clip_min.x || clip_max.y <= clip_min.y)
continue;
// Apply scissor/clipping rectangle
const D3D11_RECT r = { (LONG)clip_min.x, (LONG)clip_min.y, (LONG)clip_max.x, (LONG)clip_max.y };
ctx->RSSetScissorRects(1, &r);
// Bind texture, Draw
ID3D11ShaderResourceView* texture_srv = (ID3D11ShaderResourceView*)pcmd->GetTexID();
ctx->PSSetShaderResources(0, 1, &texture_srv);
ctx->DrawIndexed(pcmd->ElemCount, pcmd->IdxOffset + global_idx_offset, pcmd->VtxOffset + global_vtx_offset);
}
}
global_idx_offset += cmd_list->IdxBuffer.Size;
global_vtx_offset += cmd_list->VtxBuffer.Size;
}
// Restore modified DX state
ctx->RSSetScissorRects(old.ScissorRectsCount, old.ScissorRects);
ctx->RSSetViewports(old.ViewportsCount, old.Viewports);
ctx->RSSetState(old.RS); if (old.RS) old.RS->Release();
ctx->OMSetBlendState(old.BlendState, old.BlendFactor, old.SampleMask); if (old.BlendState) old.BlendState->Release();
ctx->OMSetDepthStencilState(old.DepthStencilState, old.StencilRef); if (old.DepthStencilState) old.DepthStencilState->Release();
ctx->PSSetShaderResources(0, 1, &old.PSShaderResource); if (old.PSShaderResource) old.PSShaderResource->Release();
ctx->PSSetSamplers(0, 1, &old.PSSampler); if (old.PSSampler) old.PSSampler->Release();
ctx->PSSetShader(old.PS, old.PSInstances, old.PSInstancesCount); if (old.PS) old.PS->Release();
for (UINT i = 0; i < old.PSInstancesCount; i++) if (old.PSInstances[i]) old.PSInstances[i]->Release();
ctx->VSSetShader(old.VS, old.VSInstances, old.VSInstancesCount); if (old.VS) old.VS->Release();
ctx->VSSetConstantBuffers(0, 1, &old.VSConstantBuffer); if (old.VSConstantBuffer) old.VSConstantBuffer->Release();
ctx->GSSetShader(old.GS, old.GSInstances, old.GSInstancesCount); if (old.GS) old.GS->Release();
for (UINT i = 0; i < old.VSInstancesCount; i++) if (old.VSInstances[i]) old.VSInstances[i]->Release();
ctx->IASetPrimitiveTopology(old.PrimitiveTopology);
ctx->IASetIndexBuffer(old.IndexBuffer, old.IndexBufferFormat, old.IndexBufferOffset); if (old.IndexBuffer) old.IndexBuffer->Release();
ctx->IASetVertexBuffers(0, 1, &old.VertexBuffer, &old.VertexBufferStride, &old.VertexBufferOffset); if (old.VertexBuffer) old.VertexBuffer->Release();
ctx->IASetInputLayout(old.InputLayout); if (old.InputLayout) old.InputLayout->Release();
}
static void ImGui_ImplDX11_CreateFontsTexture()
{
// Build texture atlas
ImGuiIO& io = ImGui::GetIO();
ImGui_ImplDX11_Data* bd = ImGui_ImplDX11_GetBackendData();
unsigned char* pixels;
int width, height;
io.Fonts->GetTexDataAsRGBA32(&pixels, &width, &height);
// Upload texture to graphics system
{
D3D11_TEXTURE2D_DESC desc;
ZeroMemory(&desc, sizeof(desc));
desc.Width = width;
desc.Height = height;
desc.MipLevels = 1;
desc.ArraySize = 1;
desc.Format = DXGI_FORMAT_R8G8B8A8_UNORM;
desc.SampleDesc.Count = 1;
desc.Usage = D3D11_USAGE_DEFAULT;
desc.BindFlags = D3D11_BIND_SHADER_RESOURCE;
desc.CPUAccessFlags = 0;
ID3D11Texture2D* pTexture = NULL;
D3D11_SUBRESOURCE_DATA subResource;
subResource.pSysMem = pixels;
subResource.SysMemPitch = desc.Width * 4;
subResource.SysMemSlicePitch = 0;
bd->pd3dDevice->CreateTexture2D(&desc, &subResource, &pTexture);
IM_ASSERT(pTexture != NULL);
// Create texture view
D3D11_SHADER_RESOURCE_VIEW_DESC srvDesc;
ZeroMemory(&srvDesc, sizeof(srvDesc));
srvDesc.Format = DXGI_FORMAT_R8G8B8A8_UNORM;
srvDesc.ViewDimension = D3D11_SRV_DIMENSION_TEXTURE2D;
srvDesc.Texture2D.MipLevels = desc.MipLevels;
srvDesc.Texture2D.MostDetailedMip = 0;
bd->pd3dDevice->CreateShaderResourceView(pTexture, &srvDesc, &bd->pFontTextureView);
pTexture->Release();
}
// Store our identifier
io.Fonts->SetTexID((ImTextureID)bd->pFontTextureView);
// Create texture sampler
{
D3D11_SAMPLER_DESC desc;
ZeroMemory(&desc, sizeof(desc));
desc.Filter = D3D11_FILTER_MIN_MAG_MIP_LINEAR;
desc.AddressU = D3D11_TEXTURE_ADDRESS_WRAP;
desc.AddressV = D3D11_TEXTURE_ADDRESS_WRAP;
desc.AddressW = D3D11_TEXTURE_ADDRESS_WRAP;
desc.MipLODBias = 0.f;
desc.ComparisonFunc = D3D11_COMPARISON_ALWAYS;
desc.MinLOD = 0.f;
desc.MaxLOD = 0.f;
bd->pd3dDevice->CreateSamplerState(&desc, &bd->pFontSampler);
}
}
bool ImGui_ImplDX11_CreateDeviceObjects()
{
ImGui_ImplDX11_Data* bd = ImGui_ImplDX11_GetBackendData();
if (!bd->pd3dDevice)
return false;
if (bd->pFontSampler)
ImGui_ImplDX11_InvalidateDeviceObjects();
// By using D3DCompile() from <d3dcompiler.h> / d3dcompiler.lib, we introduce a dependency to a given version of d3dcompiler_XX.dll (see D3DCOMPILER_DLL_A)
// If you would like to use this DX11 sample code but remove this dependency you can:
// 1) compile once, save the compiled shader blobs into a file or source code and pass them to CreateVertexShader()/CreatePixelShader() [preferred solution]
// 2) use code to detect any version of the DLL and grab a pointer to D3DCompile from the DLL.
// See https://github.com/ocornut/imgui/pull/638 for sources and details.
// Create the vertex shader
{
static const char* vertexShader =
"cbuffer vertexBuffer : register(b0) \
{\
float4x4 ProjectionMatrix; \
};\
struct VS_INPUT\
{\
float2 pos : POSITION;\
float4 col : COLOR0;\
float2 uv : TEXCOORD0;\
};\
\
struct PS_INPUT\
{\
float4 pos : SV_POSITION;\
float4 col : COLOR0;\
float2 uv : TEXCOORD0;\
};\
\
PS_INPUT main(VS_INPUT input)\
{\
PS_INPUT output;\
output.pos = mul( ProjectionMatrix, float4(input.pos.xy, 0.f, 1.f));\
output.col = input.col;\
output.uv = input.uv;\
return output;\
}";
ID3DBlob* vertexShaderBlob;
if (FAILED(D3DCompile(vertexShader, strlen(vertexShader), NULL, NULL, NULL, "main", "vs_4_0", 0, 0, &vertexShaderBlob, NULL)))
return false; // NB: Pass ID3DBlob* pErrorBlob to D3DCompile() to get error showing in (const char*)pErrorBlob->GetBufferPointer(). Make sure to Release() the blob!
if (bd->pd3dDevice->CreateVertexShader(vertexShaderBlob->GetBufferPointer(), vertexShaderBlob->GetBufferSize(), NULL, &bd->pVertexShader) != S_OK)
{
vertexShaderBlob->Release();
return false;
}
// Create the input layout
D3D11_INPUT_ELEMENT_DESC local_layout[] =
{
{ "POSITION", 0, DXGI_FORMAT_R32G32_FLOAT, 0, (UINT)IM_OFFSETOF(ImDrawVert, pos), D3D11_INPUT_PER_VERTEX_DATA, 0 },
{ "TEXCOORD", 0, DXGI_FORMAT_R32G32_FLOAT, 0, (UINT)IM_OFFSETOF(ImDrawVert, uv), D3D11_INPUT_PER_VERTEX_DATA, 0 },
{ "COLOR", 0, DXGI_FORMAT_R8G8B8A8_UNORM, 0, (UINT)IM_OFFSETOF(ImDrawVert, col), D3D11_INPUT_PER_VERTEX_DATA, 0 },
};
if (bd->pd3dDevice->CreateInputLayout(local_layout, 3, vertexShaderBlob->GetBufferPointer(), vertexShaderBlob->GetBufferSize(), &bd->pInputLayout) != S_OK)
{
vertexShaderBlob->Release();
return false;
}
vertexShaderBlob->Release();
// Create the constant buffer
{
D3D11_BUFFER_DESC desc;
desc.ByteWidth = sizeof(VERTEX_CONSTANT_BUFFER);
desc.Usage = D3D11_USAGE_DYNAMIC;
desc.BindFlags = D3D11_BIND_CONSTANT_BUFFER;
desc.CPUAccessFlags = D3D11_CPU_ACCESS_WRITE;
desc.MiscFlags = 0;
bd->pd3dDevice->CreateBuffer(&desc, NULL, &bd->pVertexConstantBuffer);
}
}
// Create the pixel shader
{
static const char* pixelShader =
"struct PS_INPUT\
{\
float4 pos : SV_POSITION;\
float4 col : COLOR0;\
float2 uv : TEXCOORD0;\
};\
sampler sampler0;\
Texture2D texture0;\
\
float4 main(PS_INPUT input) : SV_Target\
{\
float4 out_col = input.col * texture0.Sample(sampler0, input.uv); \
return out_col; \
}";
ID3DBlob* pixelShaderBlob;
if (FAILED(D3DCompile(pixelShader, strlen(pixelShader), NULL, NULL, NULL, "main", "ps_4_0", 0, 0, &pixelShaderBlob, NULL)))
return false; // NB: Pass ID3DBlob* pErrorBlob to D3DCompile() to get error showing in (const char*)pErrorBlob->GetBufferPointer(). Make sure to Release() the blob!
if (bd->pd3dDevice->CreatePixelShader(pixelShaderBlob->GetBufferPointer(), pixelShaderBlob->GetBufferSize(), NULL, &bd->pPixelShader) != S_OK)
{
pixelShaderBlob->Release();
return false;
}
pixelShaderBlob->Release();
}
// Create the blending setup
{
D3D11_BLEND_DESC desc;
ZeroMemory(&desc, sizeof(desc));
desc.AlphaToCoverageEnable = false;
desc.RenderTarget[0].BlendEnable = true;
desc.RenderTarget[0].SrcBlend = D3D11_BLEND_SRC_ALPHA;
desc.RenderTarget[0].DestBlend = D3D11_BLEND_INV_SRC_ALPHA;
desc.RenderTarget[0].BlendOp = D3D11_BLEND_OP_ADD;
desc.RenderTarget[0].SrcBlendAlpha = D3D11_BLEND_ONE;
desc.RenderTarget[0].DestBlendAlpha = D3D11_BLEND_INV_SRC_ALPHA;
desc.RenderTarget[0].BlendOpAlpha = D3D11_BLEND_OP_ADD;
desc.RenderTarget[0].RenderTargetWriteMask = D3D11_COLOR_WRITE_ENABLE_ALL;
bd->pd3dDevice->CreateBlendState(&desc, &bd->pBlendState);
}
// Create the rasterizer state
{
D3D11_RASTERIZER_DESC desc;
ZeroMemory(&desc, sizeof(desc));
desc.FillMode = D3D11_FILL_SOLID;
desc.CullMode = D3D11_CULL_NONE;
desc.ScissorEnable = true;
desc.DepthClipEnable = true;
bd->pd3dDevice->CreateRasterizerState(&desc, &bd->pRasterizerState);
}
// Create depth-stencil State
{
D3D11_DEPTH_STENCIL_DESC desc;
ZeroMemory(&desc, sizeof(desc));
desc.DepthEnable = false;
desc.DepthWriteMask = D3D11_DEPTH_WRITE_MASK_ALL;
desc.DepthFunc = D3D11_COMPARISON_ALWAYS;
desc.StencilEnable = false;
desc.FrontFace.StencilFailOp = desc.FrontFace.StencilDepthFailOp = desc.FrontFace.StencilPassOp = D3D11_STENCIL_OP_KEEP;
desc.FrontFace.StencilFunc = D3D11_COMPARISON_ALWAYS;
desc.BackFace = desc.FrontFace;
bd->pd3dDevice->CreateDepthStencilState(&desc, &bd->pDepthStencilState);
}
ImGui_ImplDX11_CreateFontsTexture();
return true;
}
void ImGui_ImplDX11_InvalidateDeviceObjects()
{
ImGui_ImplDX11_Data* bd = ImGui_ImplDX11_GetBackendData();
if (!bd->pd3dDevice)
return;
if (bd->pFontSampler) { bd->pFontSampler->Release(); bd->pFontSampler = NULL; }
if (bd->pFontTextureView) { bd->pFontTextureView->Release(); bd->pFontTextureView = NULL; ImGui::GetIO().Fonts->SetTexID(NULL); } // We copied data->pFontTextureView to io.Fonts->TexID so let's clear that as well.
if (bd->pIB) { bd->pIB->Release(); bd->pIB = NULL; }
if (bd->pVB) { bd->pVB->Release(); bd->pVB = NULL; }
if (bd->pBlendState) { bd->pBlendState->Release(); bd->pBlendState = NULL; }
if (bd->pDepthStencilState) { bd->pDepthStencilState->Release(); bd->pDepthStencilState = NULL; }
if (bd->pRasterizerState) { bd->pRasterizerState->Release(); bd->pRasterizerState = NULL; }
if (bd->pPixelShader) { bd->pPixelShader->Release(); bd->pPixelShader = NULL; }
if (bd->pVertexConstantBuffer) { bd->pVertexConstantBuffer->Release(); bd->pVertexConstantBuffer = NULL; }
if (bd->pInputLayout) { bd->pInputLayout->Release(); bd->pInputLayout = NULL; }
if (bd->pVertexShader) { bd->pVertexShader->Release(); bd->pVertexShader = NULL; }
}
bool ImGui_ImplDX11_Init(ID3D11Device* device, ID3D11DeviceContext* device_context)
{
ImGuiIO& io = ImGui::GetIO();
IM_ASSERT(io.BackendRendererUserData == NULL && "Already initialized a renderer backend!");
// Setup backend capabilities flags
ImGui_ImplDX11_Data* bd = IM_NEW(ImGui_ImplDX11_Data)();
io.BackendRendererUserData = (void*)bd;
io.BackendRendererName = "imgui_impl_dx11";
io.BackendFlags |= ImGuiBackendFlags_RendererHasVtxOffset; // We can honor the ImDrawCmd::VtxOffset field, allowing for large meshes.
// Get factory from device
IDXGIDevice* pDXGIDevice = NULL;
IDXGIAdapter* pDXGIAdapter = NULL;
IDXGIFactory* pFactory = NULL;
if (device->QueryInterface(IID_PPV_ARGS(&pDXGIDevice)) == S_OK)
if (pDXGIDevice->GetParent(IID_PPV_ARGS(&pDXGIAdapter)) == S_OK)
if (pDXGIAdapter->GetParent(IID_PPV_ARGS(&pFactory)) == S_OK)
{
bd->pd3dDevice = device;
bd->pd3dDeviceContext = device_context;
bd->pFactory = pFactory;
}
if (pDXGIDevice) pDXGIDevice->Release();
if (pDXGIAdapter) pDXGIAdapter->Release();
bd->pd3dDevice->AddRef();
bd->pd3dDeviceContext->AddRef();
return true;
}
void ImGui_ImplDX11_Shutdown()
{
ImGui_ImplDX11_Data* bd = ImGui_ImplDX11_GetBackendData();
IM_ASSERT(bd != NULL && "No renderer backend to shutdown, or already shutdown?");
ImGuiIO& io = ImGui::GetIO();
ImGui_ImplDX11_InvalidateDeviceObjects();
if (bd->pFactory) { bd->pFactory->Release(); }
if (bd->pd3dDevice) { bd->pd3dDevice->Release(); }
if (bd->pd3dDeviceContext) { bd->pd3dDeviceContext->Release(); }
io.BackendRendererName = NULL;
io.BackendRendererUserData = NULL;
IM_DELETE(bd);
}
void ImGui_ImplDX11_NewFrame()
{
ImGui_ImplDX11_Data* bd = ImGui_ImplDX11_GetBackendData();
IM_ASSERT(bd != NULL && "Did you call ImGui_ImplDX11_Init()?");
if (!bd->pFontSampler)
ImGui_ImplDX11_CreateDeviceObjects();
}
+26
View File
@@ -0,0 +1,26 @@
// dear imgui: Renderer Backend for DirectX11
// This needs to be used along with a Platform Backend (e.g. Win32)
// Implemented features:
// [X] Renderer: User texture binding. Use 'ID3D11ShaderResourceView*' as ImTextureID. Read the FAQ about ImTextureID!
// [X] Renderer: Support for large meshes (64k+ vertices) with 16-bit indices.
// You can use unmodified imgui_impl_* files in your project. See examples/ folder for examples of using this.
// Prefer including the entire imgui/ repository into your project (either as a copy or as a submodule), and only build the backends you need.
// If you are new to Dear ImGui, read documentation from the docs/ folder + read the top of imgui.cpp.
// Read online: https://github.com/ocornut/imgui/tree/master/docs
#pragma once
#include "imgui.h" // IMGUI_IMPL_API
struct ID3D11Device;
struct ID3D11DeviceContext;
IMGUI_IMPL_API bool ImGui_ImplDX11_Init(ID3D11Device* device, ID3D11DeviceContext* device_context);
IMGUI_IMPL_API void ImGui_ImplDX11_Shutdown();
IMGUI_IMPL_API void ImGui_ImplDX11_NewFrame();
IMGUI_IMPL_API void ImGui_ImplDX11_RenderDrawData(ImDrawData* draw_data);
// Use if you want to reset your rendering device without losing Dear ImGui state.
IMGUI_IMPL_API void ImGui_ImplDX11_InvalidateDeviceObjects();
IMGUI_IMPL_API bool ImGui_ImplDX11_CreateDeviceObjects();
+258
View File
@@ -0,0 +1,258 @@
// dear imgui: Renderer Backend for OpenGL2 (legacy OpenGL, fixed pipeline)
// This needs to be used along with a Platform Backend (e.g. GLFW, SDL, Win32, custom..)
// Implemented features:
// [X] Renderer: User texture binding. Use 'GLuint' OpenGL texture identifier as void*/ImTextureID. Read the FAQ about ImTextureID!
// You can copy and use unmodified imgui_impl_* files in your project. See examples/ folder for examples of using this.
// If you are new to Dear ImGui, read documentation from the docs/ folder + read the top of imgui.cpp.
// Read online: https://github.com/ocornut/imgui/tree/master/docs
// **DO NOT USE THIS CODE IF YOUR CODE/ENGINE IS USING MODERN OPENGL (SHADERS, VBO, VAO, etc.)**
// **Prefer using the code in imgui_impl_opengl3.cpp**
// This code is mostly provided as a reference to learn how ImGui integration works, because it is shorter to read.
// If your code is using GL3+ context or any semi modern OpenGL calls, using this is likely to make everything more
// complicated, will require your code to reset every single OpenGL attributes to their initial state, and might
// confuse your GPU driver.
// The GL2 code is unable to reset attributes or even call e.g. "glUseProgram(0)" because they don't exist in that API.
// CHANGELOG
// (minor and older changes stripped away, please see git history for details)
// 2021-01-03: OpenGL: Backup, setup and restore GL_SHADE_MODEL state, disable GL_STENCIL_TEST and disable GL_NORMAL_ARRAY client state to increase compatibility with legacy OpenGL applications.
// 2020-01-23: OpenGL: Backup, setup and restore GL_TEXTURE_ENV to increase compatibility with legacy OpenGL applications.
// 2019-04-30: OpenGL: Added support for special ImDrawCallback_ResetRenderState callback to reset render state.
// 2019-02-11: OpenGL: Projecting clipping rectangles correctly using draw_data->FramebufferScale to allow multi-viewports for retina display.
// 2018-11-30: Misc: Setting up io.BackendRendererName so it can be displayed in the About Window.
// 2018-08-03: OpenGL: Disabling/restoring GL_LIGHTING and GL_COLOR_MATERIAL to increase compatibility with legacy OpenGL applications.
// 2018-06-08: Misc: Extracted imgui_impl_opengl2.cpp/.h away from the old combined GLFW/SDL+OpenGL2 examples.
// 2018-06-08: OpenGL: Use draw_data->DisplayPos and draw_data->DisplaySize to setup projection matrix and clipping rectangle.
// 2018-02-16: Misc: Obsoleted the io.RenderDrawListsFn callback and exposed ImGui_ImplOpenGL2_RenderDrawData() in the .h file so you can call it yourself.
// 2017-09-01: OpenGL: Save and restore current polygon mode.
// 2016-09-10: OpenGL: Uploading font texture as RGBA32 to increase compatibility with users shaders (not ideal).
// 2016-09-05: OpenGL: Fixed save and restore of current scissor rectangle.
#include "imgui.h"
#include "imgui_impl_opengl2.h"
#if defined(_MSC_VER) && _MSC_VER <= 1500 // MSVC 2008 or earlier
#include <stddef.h> // intptr_t
#else
#include <stdint.h> // intptr_t
#endif
// Include OpenGL header (without an OpenGL loader) requires a bit of fiddling
#if defined(_WIN32) && !defined(APIENTRY)
#define APIENTRY __stdcall // It is customary to use APIENTRY for OpenGL function pointer declarations on all platforms. Additionally, the Windows OpenGL header needs APIENTRY.
#endif
#if defined(_WIN32) && !defined(WINGDIAPI)
#define WINGDIAPI __declspec(dllimport) // Some Windows OpenGL headers need this
#endif
#if defined(__APPLE__)
#define GL_SILENCE_DEPRECATION
#include <OpenGL/gl.h>
#else
#include <GL/gl.h>
#endif
// OpenGL Data
static GLuint g_FontTexture = 0;
// Functions
bool ImGui_ImplOpenGL2_Init()
{
// Setup backend capabilities flags
ImGuiIO& io = ImGui::GetIO();
io.BackendRendererName = "imgui_impl_opengl2";
return true;
}
void ImGui_ImplOpenGL2_Shutdown()
{
ImGui_ImplOpenGL2_DestroyDeviceObjects();
}
void ImGui_ImplOpenGL2_NewFrame()
{
if (!g_FontTexture)
ImGui_ImplOpenGL2_CreateDeviceObjects();
}
static void ImGui_ImplOpenGL2_SetupRenderState(ImDrawData* draw_data, int fb_width, int fb_height)
{
// Setup render state: alpha-blending enabled, no face culling, no depth testing, scissor enabled, vertex/texcoord/color pointers, polygon fill.
glEnable(GL_BLEND);
glBlendFunc(GL_SRC_ALPHA, GL_ONE_MINUS_SRC_ALPHA);
//glBlendFuncSeparate(GL_SRC_ALPHA, GL_ONE_MINUS_SRC_ALPHA, GL_ONE, GL_ONE_MINUS_SRC_ALPHA); // In order to composite our output buffer we need to preserve alpha
glDisable(GL_CULL_FACE);
glDisable(GL_DEPTH_TEST);
glDisable(GL_STENCIL_TEST);
glDisable(GL_LIGHTING);
glDisable(GL_COLOR_MATERIAL);
glEnable(GL_SCISSOR_TEST);
glEnableClientState(GL_VERTEX_ARRAY);
glEnableClientState(GL_TEXTURE_COORD_ARRAY);
glEnableClientState(GL_COLOR_ARRAY);
glDisableClientState(GL_NORMAL_ARRAY);
glEnable(GL_TEXTURE_2D);
glPolygonMode(GL_FRONT_AND_BACK, GL_FILL);
glShadeModel(GL_SMOOTH);
glTexEnvi(GL_TEXTURE_ENV, GL_TEXTURE_ENV_MODE, GL_MODULATE);
// If you are using this code with non-legacy OpenGL header/contexts (which you should not, prefer using imgui_impl_opengl3.cpp!!),
// you may need to backup/reset/restore other state, e.g. for current shader using the commented lines below.
// (DO NOT MODIFY THIS FILE! Add the code in your calling function)
// GLint last_program;
// glGetIntegerv(GL_CURRENT_PROGRAM, &last_program);
// glUseProgram(0);
// ImGui_ImplOpenGL2_RenderDrawData(...);
// glUseProgram(last_program)
// There are potentially many more states you could need to clear/setup that we can't access from default headers.
// e.g. glBindBuffer(GL_ARRAY_BUFFER, 0), glDisable(GL_TEXTURE_CUBE_MAP).
// Setup viewport, orthographic projection matrix
// Our visible imgui space lies from draw_data->DisplayPos (top left) to draw_data->DisplayPos+data_data->DisplaySize (bottom right). DisplayPos is (0,0) for single viewport apps.
glViewport(0, 0, (GLsizei)fb_width, (GLsizei)fb_height);
glMatrixMode(GL_PROJECTION);
glPushMatrix();
glLoadIdentity();
glOrtho(draw_data->DisplayPos.x, draw_data->DisplayPos.x + draw_data->DisplaySize.x, draw_data->DisplayPos.y + draw_data->DisplaySize.y, draw_data->DisplayPos.y, -1.0f, +1.0f);
glMatrixMode(GL_MODELVIEW);
glPushMatrix();
glLoadIdentity();
}
// OpenGL2 Render function.
// Note that this implementation is little overcomplicated because we are saving/setting up/restoring every OpenGL state explicitly.
// This is in order to be able to run within an OpenGL engine that doesn't do so.
void ImGui_ImplOpenGL2_RenderDrawData(ImDrawData* draw_data)
{
// Avoid rendering when minimized, scale coordinates for retina displays (screen coordinates != framebuffer coordinates)
int fb_width = (int)(draw_data->DisplaySize.x * draw_data->FramebufferScale.x);
int fb_height = (int)(draw_data->DisplaySize.y * draw_data->FramebufferScale.y);
if (fb_width == 0 || fb_height == 0)
return;
// Backup GL state
GLint last_texture; glGetIntegerv(GL_TEXTURE_BINDING_2D, &last_texture);
GLint last_polygon_mode[2]; glGetIntegerv(GL_POLYGON_MODE, last_polygon_mode);
GLint last_viewport[4]; glGetIntegerv(GL_VIEWPORT, last_viewport);
GLint last_scissor_box[4]; glGetIntegerv(GL_SCISSOR_BOX, last_scissor_box);
GLint last_shade_model; glGetIntegerv(GL_SHADE_MODEL, &last_shade_model);
GLint last_tex_env_mode; glGetTexEnviv(GL_TEXTURE_ENV, GL_TEXTURE_ENV_MODE, &last_tex_env_mode);
glPushAttrib(GL_ENABLE_BIT | GL_COLOR_BUFFER_BIT | GL_TRANSFORM_BIT);
// Setup desired GL state
ImGui_ImplOpenGL2_SetupRenderState(draw_data, fb_width, fb_height);
// Will project scissor/clipping rectangles into framebuffer space
ImVec2 clip_off = draw_data->DisplayPos; // (0,0) unless using multi-viewports
ImVec2 clip_scale = draw_data->FramebufferScale; // (1,1) unless using retina display which are often (2,2)
// Render command lists
for (int n = 0; n < draw_data->CmdListsCount; n++)
{
const ImDrawList* cmd_list = draw_data->CmdLists[n];
const ImDrawVert* vtx_buffer = cmd_list->VtxBuffer.Data;
const ImDrawIdx* idx_buffer = cmd_list->IdxBuffer.Data;
glVertexPointer(2, GL_FLOAT, sizeof(ImDrawVert), (const GLvoid*)((const char*)vtx_buffer + IM_OFFSETOF(ImDrawVert, pos)));
glTexCoordPointer(2, GL_FLOAT, sizeof(ImDrawVert), (const GLvoid*)((const char*)vtx_buffer + IM_OFFSETOF(ImDrawVert, uv)));
glColorPointer(4, GL_UNSIGNED_BYTE, sizeof(ImDrawVert), (const GLvoid*)((const char*)vtx_buffer + IM_OFFSETOF(ImDrawVert, col)));
for (int cmd_i = 0; cmd_i < cmd_list->CmdBuffer.Size; cmd_i++)
{
const ImDrawCmd* pcmd = &cmd_list->CmdBuffer[cmd_i];
if (pcmd->UserCallback)
{
// User callback, registered via ImDrawList::AddCallback()
// (ImDrawCallback_ResetRenderState is a special callback value used by the user to request the renderer to reset render state.)
if (pcmd->UserCallback == ImDrawCallback_ResetRenderState)
ImGui_ImplOpenGL2_SetupRenderState(draw_data, fb_width, fb_height);
else
pcmd->UserCallback(cmd_list, pcmd);
}
else
{
// Project scissor/clipping rectangles into framebuffer space
ImVec4 clip_rect;
clip_rect.x = (pcmd->ClipRect.x - clip_off.x) * clip_scale.x;
clip_rect.y = (pcmd->ClipRect.y - clip_off.y) * clip_scale.y;
clip_rect.z = (pcmd->ClipRect.z - clip_off.x) * clip_scale.x;
clip_rect.w = (pcmd->ClipRect.w - clip_off.y) * clip_scale.y;
if (clip_rect.x < fb_width && clip_rect.y < fb_height && clip_rect.z >= 0.0f && clip_rect.w >= 0.0f)
{
// Apply scissor/clipping rectangle
glScissor((int)clip_rect.x, (int)(fb_height - clip_rect.w), (int)(clip_rect.z - clip_rect.x), (int)(clip_rect.w - clip_rect.y));
// Bind texture, Draw
glBindTexture(GL_TEXTURE_2D, (GLuint)(intptr_t)pcmd->TextureId);
glDrawElements(GL_TRIANGLES, (GLsizei)pcmd->ElemCount, sizeof(ImDrawIdx) == 2 ? GL_UNSIGNED_SHORT : GL_UNSIGNED_INT, idx_buffer);
}
}
idx_buffer += pcmd->ElemCount;
}
}
// Restore modified GL state
glDisableClientState(GL_COLOR_ARRAY);
glDisableClientState(GL_TEXTURE_COORD_ARRAY);
glDisableClientState(GL_VERTEX_ARRAY);
glBindTexture(GL_TEXTURE_2D, (GLuint)last_texture);
glMatrixMode(GL_MODELVIEW);
glPopMatrix();
glMatrixMode(GL_PROJECTION);
glPopMatrix();
glPopAttrib();
glPolygonMode(GL_FRONT, (GLenum)last_polygon_mode[0]); glPolygonMode(GL_BACK, (GLenum)last_polygon_mode[1]);
glViewport(last_viewport[0], last_viewport[1], (GLsizei)last_viewport[2], (GLsizei)last_viewport[3]);
glScissor(last_scissor_box[0], last_scissor_box[1], (GLsizei)last_scissor_box[2], (GLsizei)last_scissor_box[3]);
glShadeModel(last_shade_model);
glTexEnvi(GL_TEXTURE_ENV, GL_TEXTURE_ENV_MODE, last_tex_env_mode);
}
bool ImGui_ImplOpenGL2_CreateFontsTexture()
{
// Build texture atlas
ImGuiIO& io = ImGui::GetIO();
unsigned char* pixels;
int width, height;
io.Fonts->GetTexDataAsRGBA32(&pixels, &width, &height); // Load as RGBA 32-bit (75% of the memory is wasted, but default font is so small) because it is more likely to be compatible with user's existing shaders. If your ImTextureId represent a higher-level concept than just a GL texture id, consider calling GetTexDataAsAlpha8() instead to save on GPU memory.
// Upload texture to graphics system
GLint last_texture;
glGetIntegerv(GL_TEXTURE_BINDING_2D, &last_texture);
glGenTextures(1, &g_FontTexture);
glBindTexture(GL_TEXTURE_2D, g_FontTexture);
glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_MIN_FILTER, GL_LINEAR);
glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_MAG_FILTER, GL_LINEAR);
glPixelStorei(GL_UNPACK_ROW_LENGTH, 0);
glTexImage2D(GL_TEXTURE_2D, 0, GL_RGBA, width, height, 0, GL_RGBA, GL_UNSIGNED_BYTE, pixels);
// Store our identifier
io.Fonts->SetTexID((ImTextureID)(intptr_t)g_FontTexture);
// Restore state
glBindTexture(GL_TEXTURE_2D, last_texture);
return true;
}
void ImGui_ImplOpenGL2_DestroyFontsTexture()
{
if (g_FontTexture)
{
ImGuiIO& io = ImGui::GetIO();
glDeleteTextures(1, &g_FontTexture);
io.Fonts->SetTexID(0);
g_FontTexture = 0;
}
}
bool ImGui_ImplOpenGL2_CreateDeviceObjects()
{
return ImGui_ImplOpenGL2_CreateFontsTexture();
}
void ImGui_ImplOpenGL2_DestroyDeviceObjects()
{
ImGui_ImplOpenGL2_DestroyFontsTexture();
}
+31
View File
@@ -0,0 +1,31 @@
// dear imgui: Renderer Backend for OpenGL2 (legacy OpenGL, fixed pipeline)
// This needs to be used along with a Platform Backend (e.g. GLFW, SDL, Win32, custom..)
// Implemented features:
// [X] Renderer: User texture binding. Use 'GLuint' OpenGL texture identifier as void*/ImTextureID. Read the FAQ about ImTextureID!
// You can copy and use unmodified imgui_impl_* files in your project. See examples/ folder for examples of using this.
// If you are new to Dear ImGui, read documentation from the docs/ folder + read the top of imgui.cpp.
// Read online: https://github.com/ocornut/imgui/tree/master/docs
// **DO NOT USE THIS CODE IF YOUR CODE/ENGINE IS USING MODERN OPENGL (SHADERS, VBO, VAO, etc.)**
// **Prefer using the code in imgui_impl_opengl3.cpp**
// This code is mostly provided as a reference to learn how ImGui integration works, because it is shorter to read.
// If your code is using GL3+ context or any semi modern OpenGL calls, using this is likely to make everything more
// complicated, will require your code to reset every single OpenGL attributes to their initial state, and might
// confuse your GPU driver.
// The GL2 code is unable to reset attributes or even call e.g. "glUseProgram(0)" because they don't exist in that API.
#pragma once
#include "imgui.h" // IMGUI_IMPL_API
IMGUI_IMPL_API bool ImGui_ImplOpenGL2_Init();
IMGUI_IMPL_API void ImGui_ImplOpenGL2_Shutdown();
IMGUI_IMPL_API void ImGui_ImplOpenGL2_NewFrame();
IMGUI_IMPL_API void ImGui_ImplOpenGL2_RenderDrawData(ImDrawData* draw_data);
// Called by Init/NewFrame/Shutdown
IMGUI_IMPL_API bool ImGui_ImplOpenGL2_CreateFontsTexture();
IMGUI_IMPL_API void ImGui_ImplOpenGL2_DestroyFontsTexture();
IMGUI_IMPL_API bool ImGui_ImplOpenGL2_CreateDeviceObjects();
IMGUI_IMPL_API void ImGui_ImplOpenGL2_DestroyDeviceObjects();
+377
View File
@@ -0,0 +1,377 @@
// dear imgui: Platform Backend for SDL2
// This needs to be used along with a Renderer (e.g. DirectX11, OpenGL3, Vulkan..)
// (Info: SDL2 is a cross-platform general purpose library for handling windows, inputs, graphics context creation, etc.)
// (Requires: SDL 2.0. Prefer SDL 2.0.4+ for full feature support.)
// Implemented features:
// [X] Platform: Mouse cursor shape and visibility. Disable with 'io.ConfigFlags |= ImGuiConfigFlags_NoMouseCursorChange'.
// [X] Platform: Clipboard support.
// [X] Platform: Keyboard arrays indexed using SDL_SCANCODE_* codes, e.g. ImGui::IsKeyPressed(SDL_SCANCODE_SPACE).
// [X] Platform: Gamepad support. Enabled with 'io.ConfigFlags |= ImGuiConfigFlags_NavEnableGamepad'.
// Missing features:
// [ ] Platform: SDL2 handling of IME under Windows appears to be broken and it explicitly disable the regular Windows IME. You can restore Windows IME by compiling SDL with SDL_DISABLE_WINDOWS_IME.
// You can copy and use unmodified imgui_impl_* files in your project. See examples/ folder for examples of using this.
// If you are new to Dear ImGui, read documentation from the docs/ folder + read the top of imgui.cpp.
// Read online: https://github.com/ocornut/imgui/tree/master/docs
// CHANGELOG
// (minor and older changes stripped away, please see git history for details)
// 2021-03-22: Rework global mouse pos availability check listing supported platforms explicitly, effectively fixing mouse access on Raspberry Pi. (#2837, #3950)
// 2020-05-25: Misc: Report a zero display-size when window is minimized, to be consistent with other backends.
// 2020-02-20: Inputs: Fixed mapping for ImGuiKey_KeyPadEnter (using SDL_SCANCODE_KP_ENTER instead of SDL_SCANCODE_RETURN2).
// 2019-12-17: Inputs: On Wayland, use SDL_GetMouseState (because there is no global mouse state).
// 2019-12-05: Inputs: Added support for ImGuiMouseCursor_NotAllowed mouse cursor.
// 2019-07-21: Inputs: Added mapping for ImGuiKey_KeyPadEnter.
// 2019-04-23: Inputs: Added support for SDL_GameController (if ImGuiConfigFlags_NavEnableGamepad is set by user application).
// 2019-03-12: Misc: Preserve DisplayFramebufferScale when main window is minimized.
// 2018-12-21: Inputs: Workaround for Android/iOS which don't seem to handle focus related calls.
// 2018-11-30: Misc: Setting up io.BackendPlatformName so it can be displayed in the About Window.
// 2018-11-14: Changed the signature of ImGui_ImplSDL2_ProcessEvent() to take a 'const SDL_Event*'.
// 2018-08-01: Inputs: Workaround for Emscripten which doesn't seem to handle focus related calls.
// 2018-06-29: Inputs: Added support for the ImGuiMouseCursor_Hand cursor.
// 2018-06-08: Misc: Extracted imgui_impl_sdl.cpp/.h away from the old combined SDL2+OpenGL/Vulkan examples.
// 2018-06-08: Misc: ImGui_ImplSDL2_InitForOpenGL() now takes a SDL_GLContext parameter.
// 2018-05-09: Misc: Fixed clipboard paste memory leak (we didn't call SDL_FreeMemory on the data returned by SDL_GetClipboardText).
// 2018-03-20: Misc: Setup io.BackendFlags ImGuiBackendFlags_HasMouseCursors flag + honor ImGuiConfigFlags_NoMouseCursorChange flag.
// 2018-02-16: Inputs: Added support for mouse cursors, honoring ImGui::GetMouseCursor() value.
// 2018-02-06: Misc: Removed call to ImGui::Shutdown() which is not available from 1.60 WIP, user needs to call CreateContext/DestroyContext themselves.
// 2018-02-06: Inputs: Added mapping for ImGuiKey_Space.
// 2018-02-05: Misc: Using SDL_GetPerformanceCounter() instead of SDL_GetTicks() to be able to handle very high framerate (1000+ FPS).
// 2018-02-05: Inputs: Keyboard mapping is using scancodes everywhere instead of a confusing mixture of keycodes and scancodes.
// 2018-01-20: Inputs: Added Horizontal Mouse Wheel support.
// 2018-01-19: Inputs: When available (SDL 2.0.4+) using SDL_CaptureMouse() to retrieve coordinates outside of client area when dragging. Otherwise (SDL 2.0.3 and before) testing for SDL_WINDOW_INPUT_FOCUS instead of SDL_WINDOW_MOUSE_FOCUS.
// 2018-01-18: Inputs: Added mapping for ImGuiKey_Insert.
// 2017-08-25: Inputs: MousePos set to -FLT_MAX,-FLT_MAX when mouse is unavailable/missing (instead of -1,-1).
// 2016-10-15: Misc: Added a void* user_data parameter to Clipboard function handlers.
#include "imgui.h"
#include "imgui_impl_sdl.h"
// SDL
#include <SDL.h>
#include <SDL_syswm.h>
#if defined(__APPLE__)
#include "TargetConditionals.h"
#endif
#define SDL_HAS_CAPTURE_AND_GLOBAL_MOUSE SDL_VERSION_ATLEAST(2,0,4)
#define SDL_HAS_VULKAN SDL_VERSION_ATLEAST(2,0,6)
// Data
static SDL_Window* g_Window = NULL;
static Uint64 g_Time = 0;
static bool g_MousePressed[3] = { false, false, false };
static SDL_Cursor* g_MouseCursors[ImGuiMouseCursor_COUNT] = {};
static char* g_ClipboardTextData = NULL;
static bool g_MouseCanUseGlobalState = true;
static const char* ImGui_ImplSDL2_GetClipboardText(void*)
{
if (g_ClipboardTextData)
SDL_free(g_ClipboardTextData);
g_ClipboardTextData = SDL_GetClipboardText();
return g_ClipboardTextData;
}
static void ImGui_ImplSDL2_SetClipboardText(void*, const char* text)
{
SDL_SetClipboardText(text);
}
// You can read the io.WantCaptureMouse, io.WantCaptureKeyboard flags to tell if dear imgui wants to use your inputs.
// - When io.WantCaptureMouse is true, do not dispatch mouse input data to your main application.
// - When io.WantCaptureKeyboard is true, do not dispatch keyboard input data to your main application.
// Generally you may always pass all inputs to dear imgui, and hide them from your application based on those two flags.
// If you have multiple SDL events and some of them are not meant to be used by dear imgui, you may need to filter events based on their windowID field.
bool ImGui_ImplSDL2_ProcessEvent(const SDL_Event* event)
{
ImGuiIO& io = ImGui::GetIO();
switch (event->type)
{
case SDL_MOUSEWHEEL:
{
if (event->wheel.x > 0) io.MouseWheelH += 1;
if (event->wheel.x < 0) io.MouseWheelH -= 1;
if (event->wheel.y > 0) io.MouseWheel += 1;
if (event->wheel.y < 0) io.MouseWheel -= 1;
return true;
}
case SDL_MOUSEBUTTONDOWN:
{
if (event->button.button == SDL_BUTTON_LEFT) g_MousePressed[0] = true;
if (event->button.button == SDL_BUTTON_RIGHT) g_MousePressed[1] = true;
if (event->button.button == SDL_BUTTON_MIDDLE) g_MousePressed[2] = true;
return true;
}
case SDL_TEXTINPUT:
{
io.AddInputCharactersUTF8(event->text.text);
return true;
}
case SDL_KEYDOWN:
case SDL_KEYUP:
{
int key = event->key.keysym.scancode;
IM_ASSERT(key >= 0 && key < IM_ARRAYSIZE(io.KeysDown));
io.KeysDown[key] = (event->type == SDL_KEYDOWN);
io.KeyShift = ((SDL_GetModState() & KMOD_SHIFT) != 0);
io.KeyCtrl = ((SDL_GetModState() & KMOD_CTRL) != 0);
io.KeyAlt = ((SDL_GetModState() & KMOD_ALT) != 0);
#ifdef _WIN32
io.KeySuper = false;
#else
io.KeySuper = ((SDL_GetModState() & KMOD_GUI) != 0);
#endif
return true;
}
}
return false;
}
static bool ImGui_ImplSDL2_Init(SDL_Window* window)
{
g_Window = window;
// Setup backend capabilities flags
ImGuiIO& io = ImGui::GetIO();
io.BackendFlags |= ImGuiBackendFlags_HasMouseCursors; // We can honor GetMouseCursor() values (optional)
io.BackendFlags |= ImGuiBackendFlags_HasSetMousePos; // We can honor io.WantSetMousePos requests (optional, rarely used)
io.BackendPlatformName = "imgui_impl_sdl";
// Keyboard mapping. Dear ImGui will use those indices to peek into the io.KeysDown[] array.
io.KeyMap[ImGuiKey_Tab] = SDL_SCANCODE_TAB;
io.KeyMap[ImGuiKey_LeftArrow] = SDL_SCANCODE_LEFT;
io.KeyMap[ImGuiKey_RightArrow] = SDL_SCANCODE_RIGHT;
io.KeyMap[ImGuiKey_UpArrow] = SDL_SCANCODE_UP;
io.KeyMap[ImGuiKey_DownArrow] = SDL_SCANCODE_DOWN;
io.KeyMap[ImGuiKey_PageUp] = SDL_SCANCODE_PAGEUP;
io.KeyMap[ImGuiKey_PageDown] = SDL_SCANCODE_PAGEDOWN;
io.KeyMap[ImGuiKey_Home] = SDL_SCANCODE_HOME;
io.KeyMap[ImGuiKey_End] = SDL_SCANCODE_END;
io.KeyMap[ImGuiKey_Insert] = SDL_SCANCODE_INSERT;
io.KeyMap[ImGuiKey_Delete] = SDL_SCANCODE_DELETE;
io.KeyMap[ImGuiKey_Backspace] = SDL_SCANCODE_BACKSPACE;
io.KeyMap[ImGuiKey_Space] = SDL_SCANCODE_SPACE;
io.KeyMap[ImGuiKey_Enter] = SDL_SCANCODE_RETURN;
io.KeyMap[ImGuiKey_Escape] = SDL_SCANCODE_ESCAPE;
io.KeyMap[ImGuiKey_KeyPadEnter] = SDL_SCANCODE_KP_ENTER;
io.KeyMap[ImGuiKey_A] = SDL_SCANCODE_A;
io.KeyMap[ImGuiKey_C] = SDL_SCANCODE_C;
io.KeyMap[ImGuiKey_V] = SDL_SCANCODE_V;
io.KeyMap[ImGuiKey_X] = SDL_SCANCODE_X;
io.KeyMap[ImGuiKey_Y] = SDL_SCANCODE_Y;
io.KeyMap[ImGuiKey_Z] = SDL_SCANCODE_Z;
io.SetClipboardTextFn = ImGui_ImplSDL2_SetClipboardText;
io.GetClipboardTextFn = ImGui_ImplSDL2_GetClipboardText;
io.ClipboardUserData = NULL;
// Load mouse cursors
g_MouseCursors[ImGuiMouseCursor_Arrow] = SDL_CreateSystemCursor(SDL_SYSTEM_CURSOR_ARROW);
g_MouseCursors[ImGuiMouseCursor_TextInput] = SDL_CreateSystemCursor(SDL_SYSTEM_CURSOR_IBEAM);
g_MouseCursors[ImGuiMouseCursor_ResizeAll] = SDL_CreateSystemCursor(SDL_SYSTEM_CURSOR_SIZEALL);
g_MouseCursors[ImGuiMouseCursor_ResizeNS] = SDL_CreateSystemCursor(SDL_SYSTEM_CURSOR_SIZENS);
g_MouseCursors[ImGuiMouseCursor_ResizeEW] = SDL_CreateSystemCursor(SDL_SYSTEM_CURSOR_SIZEWE);
g_MouseCursors[ImGuiMouseCursor_ResizeNESW] = SDL_CreateSystemCursor(SDL_SYSTEM_CURSOR_SIZENESW);
g_MouseCursors[ImGuiMouseCursor_ResizeNWSE] = SDL_CreateSystemCursor(SDL_SYSTEM_CURSOR_SIZENWSE);
g_MouseCursors[ImGuiMouseCursor_Hand] = SDL_CreateSystemCursor(SDL_SYSTEM_CURSOR_HAND);
g_MouseCursors[ImGuiMouseCursor_NotAllowed] = SDL_CreateSystemCursor(SDL_SYSTEM_CURSOR_NO);
// Check and store if we are on a SDL backend that supports global mouse position
// ("wayland" and "rpi" don't support it, but we chose to use a white-list instead of a black-list)
const char* sdl_backend = SDL_GetCurrentVideoDriver();
const char* global_mouse_whitelist[] = { "windows", "cocoa", "x11", "DIVE", "VMAN" };
g_MouseCanUseGlobalState = false;
for (int n = 0; n < IM_ARRAYSIZE(global_mouse_whitelist); n++)
if (strncmp(sdl_backend, global_mouse_whitelist[n], strlen(global_mouse_whitelist[n])) == 0)
g_MouseCanUseGlobalState = true;
#ifdef _WIN32
SDL_SysWMinfo wmInfo;
SDL_VERSION(&wmInfo.version);
SDL_GetWindowWMInfo(window, &wmInfo);
io.ImeWindowHandle = wmInfo.info.win.window;
#else
(void)window;
#endif
return true;
}
bool ImGui_ImplSDL2_InitForOpenGL(SDL_Window* window, void* sdl_gl_context)
{
(void)sdl_gl_context; // Viewport branch will need this.
return ImGui_ImplSDL2_Init(window);
}
bool ImGui_ImplSDL2_InitForVulkan(SDL_Window* window)
{
#if !SDL_HAS_VULKAN
IM_ASSERT(0 && "Unsupported");
#endif
return ImGui_ImplSDL2_Init(window);
}
bool ImGui_ImplSDL2_InitForD3D(SDL_Window* window)
{
#if !defined(_WIN32)
IM_ASSERT(0 && "Unsupported");
#endif
return ImGui_ImplSDL2_Init(window);
}
bool ImGui_ImplSDL2_InitForMetal(SDL_Window* window)
{
return ImGui_ImplSDL2_Init(window);
}
void ImGui_ImplSDL2_Shutdown()
{
g_Window = NULL;
// Destroy last known clipboard data
if (g_ClipboardTextData)
SDL_free(g_ClipboardTextData);
g_ClipboardTextData = NULL;
// Destroy SDL mouse cursors
for (ImGuiMouseCursor cursor_n = 0; cursor_n < ImGuiMouseCursor_COUNT; cursor_n++)
SDL_FreeCursor(g_MouseCursors[cursor_n]);
memset(g_MouseCursors, 0, sizeof(g_MouseCursors));
}
static void ImGui_ImplSDL2_UpdateMousePosAndButtons()
{
ImGuiIO& io = ImGui::GetIO();
// Set OS mouse position if requested (rarely used, only when ImGuiConfigFlags_NavEnableSetMousePos is enabled by user)
if (io.WantSetMousePos)
SDL_WarpMouseInWindow(g_Window, (int)io.MousePos.x, (int)io.MousePos.y);
else
io.MousePos = ImVec2(-FLT_MAX, -FLT_MAX);
int mx, my;
Uint32 mouse_buttons = SDL_GetMouseState(&mx, &my);
io.MouseDown[0] = g_MousePressed[0] || (mouse_buttons & SDL_BUTTON(SDL_BUTTON_LEFT)) != 0; // If a mouse press event came, always pass it as "mouse held this frame", so we don't miss click-release events that are shorter than 1 frame.
io.MouseDown[1] = g_MousePressed[1] || (mouse_buttons & SDL_BUTTON(SDL_BUTTON_RIGHT)) != 0;
io.MouseDown[2] = g_MousePressed[2] || (mouse_buttons & SDL_BUTTON(SDL_BUTTON_MIDDLE)) != 0;
g_MousePressed[0] = g_MousePressed[1] = g_MousePressed[2] = false;
#if SDL_HAS_CAPTURE_AND_GLOBAL_MOUSE && !defined(__EMSCRIPTEN__) && !defined(__ANDROID__) && !(defined(__APPLE__) && TARGET_OS_IOS)
SDL_Window* focused_window = SDL_GetKeyboardFocus();
if (g_Window == focused_window)
{
if (g_MouseCanUseGlobalState)
{
// SDL_GetMouseState() gives mouse position seemingly based on the last window entered/focused(?)
// The creation of a new windows at runtime and SDL_CaptureMouse both seems to severely mess up with that, so we retrieve that position globally.
// Won't use this workaround on SDL backends that have no global mouse position, like Wayland or RPI
int wx, wy;
SDL_GetWindowPosition(focused_window, &wx, &wy);
SDL_GetGlobalMouseState(&mx, &my);
mx -= wx;
my -= wy;
}
io.MousePos = ImVec2((float)mx, (float)my);
}
// SDL_CaptureMouse() let the OS know e.g. that our imgui drag outside the SDL window boundaries shouldn't e.g. trigger the OS window resize cursor.
// The function is only supported from SDL 2.0.4 (released Jan 2016)
bool any_mouse_button_down = ImGui::IsAnyMouseDown();
SDL_CaptureMouse(any_mouse_button_down ? SDL_TRUE : SDL_FALSE);
#else
if (SDL_GetWindowFlags(g_Window) & SDL_WINDOW_INPUT_FOCUS)
io.MousePos = ImVec2((float)mx, (float)my);
#endif
}
static void ImGui_ImplSDL2_UpdateMouseCursor()
{
ImGuiIO& io = ImGui::GetIO();
if (io.ConfigFlags & ImGuiConfigFlags_NoMouseCursorChange)
return;
ImGuiMouseCursor imgui_cursor = ImGui::GetMouseCursor();
if (io.MouseDrawCursor || imgui_cursor == ImGuiMouseCursor_None)
{
// Hide OS mouse cursor if imgui is drawing it or if it wants no cursor
SDL_ShowCursor(SDL_FALSE);
}
else
{
// Show OS mouse cursor
SDL_SetCursor(g_MouseCursors[imgui_cursor] ? g_MouseCursors[imgui_cursor] : g_MouseCursors[ImGuiMouseCursor_Arrow]);
SDL_ShowCursor(SDL_TRUE);
}
}
static void ImGui_ImplSDL2_UpdateGamepads()
{
ImGuiIO& io = ImGui::GetIO();
memset(io.NavInputs, 0, sizeof(io.NavInputs));
if ((io.ConfigFlags & ImGuiConfigFlags_NavEnableGamepad) == 0)
return;
// Get gamepad
SDL_GameController* game_controller = SDL_GameControllerOpen(0);
if (!game_controller)
{
io.BackendFlags &= ~ImGuiBackendFlags_HasGamepad;
return;
}
// Update gamepad inputs
#define MAP_BUTTON(NAV_NO, BUTTON_NO) { io.NavInputs[NAV_NO] = (SDL_GameControllerGetButton(game_controller, BUTTON_NO) != 0) ? 1.0f : 0.0f; }
#define MAP_ANALOG(NAV_NO, AXIS_NO, V0, V1) { float vn = (float)(SDL_GameControllerGetAxis(game_controller, AXIS_NO) - V0) / (float)(V1 - V0); if (vn > 1.0f) vn = 1.0f; if (vn > 0.0f && io.NavInputs[NAV_NO] < vn) io.NavInputs[NAV_NO] = vn; }
const int thumb_dead_zone = 8000; // SDL_gamecontroller.h suggests using this value.
MAP_BUTTON(ImGuiNavInput_Activate, SDL_CONTROLLER_BUTTON_A); // Cross / A
MAP_BUTTON(ImGuiNavInput_Cancel, SDL_CONTROLLER_BUTTON_B); // Circle / B
MAP_BUTTON(ImGuiNavInput_Menu, SDL_CONTROLLER_BUTTON_X); // Square / X
MAP_BUTTON(ImGuiNavInput_Input, SDL_CONTROLLER_BUTTON_Y); // Triangle / Y
MAP_BUTTON(ImGuiNavInput_DpadLeft, SDL_CONTROLLER_BUTTON_DPAD_LEFT); // D-Pad Left
MAP_BUTTON(ImGuiNavInput_DpadRight, SDL_CONTROLLER_BUTTON_DPAD_RIGHT); // D-Pad Right
MAP_BUTTON(ImGuiNavInput_DpadUp, SDL_CONTROLLER_BUTTON_DPAD_UP); // D-Pad Up
MAP_BUTTON(ImGuiNavInput_DpadDown, SDL_CONTROLLER_BUTTON_DPAD_DOWN); // D-Pad Down
MAP_BUTTON(ImGuiNavInput_FocusPrev, SDL_CONTROLLER_BUTTON_LEFTSHOULDER); // L1 / LB
MAP_BUTTON(ImGuiNavInput_FocusNext, SDL_CONTROLLER_BUTTON_RIGHTSHOULDER); // R1 / RB
MAP_BUTTON(ImGuiNavInput_TweakSlow, SDL_CONTROLLER_BUTTON_LEFTSHOULDER); // L1 / LB
MAP_BUTTON(ImGuiNavInput_TweakFast, SDL_CONTROLLER_BUTTON_RIGHTSHOULDER); // R1 / RB
MAP_ANALOG(ImGuiNavInput_LStickLeft, SDL_CONTROLLER_AXIS_LEFTX, -thumb_dead_zone, -32768);
MAP_ANALOG(ImGuiNavInput_LStickRight, SDL_CONTROLLER_AXIS_LEFTX, +thumb_dead_zone, +32767);
MAP_ANALOG(ImGuiNavInput_LStickUp, SDL_CONTROLLER_AXIS_LEFTY, -thumb_dead_zone, -32767);
MAP_ANALOG(ImGuiNavInput_LStickDown, SDL_CONTROLLER_AXIS_LEFTY, +thumb_dead_zone, +32767);
io.BackendFlags |= ImGuiBackendFlags_HasGamepad;
#undef MAP_BUTTON
#undef MAP_ANALOG
}
void ImGui_ImplSDL2_NewFrame(SDL_Window* window)
{
ImGuiIO& io = ImGui::GetIO();
IM_ASSERT(io.Fonts->IsBuilt() && "Font atlas not built! It is generally built by the renderer backend. Missing call to renderer _NewFrame() function? e.g. ImGui_ImplOpenGL3_NewFrame().");
// Setup display size (every frame to accommodate for window resizing)
int w, h;
int display_w, display_h;
SDL_GetWindowSize(window, &w, &h);
if (SDL_GetWindowFlags(window) & SDL_WINDOW_MINIMIZED)
w = h = 0;
SDL_GL_GetDrawableSize(window, &display_w, &display_h);
io.DisplaySize = ImVec2((float)w, (float)h);
if (w > 0 && h > 0)
io.DisplayFramebufferScale = ImVec2((float)display_w / w, (float)display_h / h);
// Setup time step (we don't use SDL_GetTicks() because it is using millisecond resolution)
static Uint64 frequency = SDL_GetPerformanceFrequency();
Uint64 current_time = SDL_GetPerformanceCounter();
io.DeltaTime = g_Time > 0 ? (float)((double)(current_time - g_Time) / frequency) : (float)(1.0f / 60.0f);
g_Time = current_time;
ImGui_ImplSDL2_UpdateMousePosAndButtons();
ImGui_ImplSDL2_UpdateMouseCursor();
// Update game controllers (if enabled and available)
ImGui_ImplSDL2_UpdateGamepads();
}
Loaded 100 of 142 files, more files were not shown because too many files have changed in this diff. Show more