Files
CoCo3_Plus_MiSTer/rtl/sdc.sv
shodge12 1da70a7929 Core changes and CSAVE support.
1.	Added support for cassette save.  To use: A) You have to have a file [anyname.cas]
	which is larger than needed.  B) Select the file through the UI Menu 'Save
	Cassette'.  C)Set 'Cass Rwd=0 / Rec=1' to 1. D) Issue your 'CSAVE "NAME"'
	E) When done, set 'Cass Rwd=0 / Rec=1' to 0 to complete the write.  The file can
	now be loaded or copied.  Note a dummy file of a specific size can be created in
	the MiSTer SSH shell in the /media/fat/games/coco3 with the command:
	'truncate -s 65536 tapefileame.cas'. [Note do NOT use over 65536 file length]
2.	Fixed serial interrupt [6551] to not be functional on slot 3 [carts].
3.	Modification of sys_top.v to override use of USER_IO for HDMI - so it can be used
	for logic analyzer debug.  This will only occur when `define	Config_Debug is
	enabled in config.v.
4.	Fixed MUGS of powerup issue occurring on some MiSTer units.
5.	Fixed incorrect application of GIME_IRQ on legacy interrupts.  Fixed race condition
	on reading IRQ status vs clearing the interrupt.
6.	Improved Castle of Tharoggad.  App now loads but locks as the graphics animate.  This
	change improved mmu usage through to CARTS.
7.	Builds now keep track of multiple builds in the same date.  It shows as V240512-001 in
	the menus.  Its also exposed to BASIC and a boot.vhd which can be enabled to autorun is
	supplied in the archive to show how it works.
8.	Additionally, on the boot.vhd disk, is a program which demonstrated how to load a font -
	IBMFONT.BAS. Run it and it maps a font much like the IBM font to the 80 column format.
	Also, a file called TESTRTC.BAS pulls the MiSTer RTC values exposed in BASIC to display
	a clock.
9.	Large improvement in the Timer function.  Code closer emulates COCO3 Timer. Fixes
	Sliphead cart.
10.	In the 20231023 release the wd1773 instances were reduced to 1 for the FDC and one for
	the FDC.  This saved space but introduced a bug when using multiple drives at the same
	time - like a copy command.  This change was removed and the copy command works again.

To Do...
1.	Add Speech / Music cart
2.	Fix Castle of Tharoggad
2024-05-14 23:00:16 -04:00

517 lines
12 KiB
Systemverilog

////////////////////////////////////////////////////////////////////////////////
// Project Name: COCO3 Targeting MISTer
// File Name: sdc.sv
//
// SD Controller for MISTer
//
////////////////////////////////////////////////////////////////////////////////
//
// Code based partily on work by Gary Becker
// Copyright (c) 2008 Gary Becker ([email protected])
//
// SD Controller (sdc.vs) by Stan Hodge ([email protected])
// Copyright (c) 2022 by Stan Hodge ([email protected])
//
// All rights reserved
// Redistribution and use in source and synthezised forms, with or without
// modification, are permitted provided that the following conditions are met:
//
// Redistributions of source code must retain the above copyright notice,
// this list of conditions and the following disclaimer.
//
// Redistributions in synthesized form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the distribution.
//
// Neither the name of the author nor the names of other contributors may
// be used to endorse or promote products derived from this software without
// specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
// THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
// PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
// CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
// POSSIBILITY OF SUCH DAMAGE.
//
// Please report bugs to the author, but before you do so, please
// make sure that this is not a derivative work and that
// you have the latest version of this file.
//
////////////////////////////////////////////////////////////////////////////////
////////////////////////////////////////////////////////////////////////////////
module sdc(
input CLK, // clock
input RESET_N, // async reset
input [3:0] ADDRESS, // i/o port addr [extended for coco]
input [7:0] SDC_DATA_IN, // data in
output [7:0] SDC_READ_DATA, // data out
input SDC_EN, // SDC is active
input CLK_EN,
input SDC_WR,
input SDC_RD,
output reg sdc_HALT,
output reg ext_response,
output reg sdc_always,
// SD block level interface
output [31:0] sd_lba[2],
output reg [1:0] sd_rd,
output reg [1:0] sd_wr,
input [1:0] sd_ack,
// Drive descripters
input drive_wp[2],
input [1:0] drive_ready,
input [31:0] drive_size[2],
// SD byte level access. Signals for 2-PORT altsyncram.
input [8:0] sd_buff_addr,
input [7:0] sd_buff_dout,
output [7:0] sd_buff_din[2],
input sd_buff_wr
);
// Define Config features
`include "../rtl/config.sv"
reg [23:0] LSN;
reg [7:0] command;
reg [7:0] transfer_address;
reg new_cmd, new_cmd_d, cmd_done;
reg data_inc, run;
reg rxt_res_end;
reg transfer_clear;
reg [3:0] sdc_data_reg;
wire [7:0] sdc_status_reg = {sdc_data_reg, 4'h4};
enum int unsigned
{
state_idle = 0,
state_read = 1,
state_r1 = 2,
state_r1a = 3,
state_r2 = 4,
state_r3 = 5,
state_r4 = 6,
state_write = 7,
state_w1 = 8,
state_w1a = 9,
state_w2 = 10,
state_w3 = 11,
state_w4 = 12,
state_ext = 13,
state_e1 = 14,
state_e2 = 15
} state;
localparam ADRS_FF42 = 4'h2;
localparam ADRS_FF43 = 4'h3;
localparam ADRS_FF48 = 4'h8;
localparam ADRS_FF49 = 4'h9;
localparam ADRS_FF4A = 4'hA;
localparam ADRS_FF4B = 4'hB;
always @(negedge CLK or negedge RESET_N)
begin
if(!RESET_N)
begin
LSN <= 24'h000000;
command <= 8'h00;
new_cmd <= 1'b0;
data_inc <= 1'b0;
rxt_res_end <= 1'b0;
transfer_address <= 8'h00;
sdc_data_reg <= 4'h0;
end
else
begin
data_inc <= 1'b0;
rxt_res_end <= 1'b0;
if (cmd_done)
new_cmd <= 1'b0;
if (CLK_EN & SDC_WR) //Write
begin
case(ADDRESS)
ADRS_FF42: // $ff42
sdc_data_reg <= SDC_DATA_IN[7:4];
endcase
end
if (SDC_EN & CLK_EN & SDC_WR) //Write
begin
case(ADDRESS)
ADRS_FF48: // $ff48
begin
command <= SDC_DATA_IN;
transfer_address <= 8'h00;
new_cmd <= 1'b1;
end
ADRS_FF49: // $ff49
if (~run)
LSN[23:16] <= SDC_DATA_IN;
ADRS_FF4A: // $ff4A
begin
if (~run)
LSN[15:8] <= SDC_DATA_IN;
else
data_inc <= 1'b1;
end
ADRS_FF4B: // $ff4B
begin
if (~run)
LSN[7:0] <= SDC_DATA_IN;
else
begin
data_inc <= 1'b1;
end
end
endcase
end
if (CLK_EN & SDC_RD & (ADDRESS[3:1] == 3'b101) & (run)) // Read @ $ff4A / $ff4B
data_inc <= 1'b1;
if (CLK_EN & SDC_RD & (ADDRESS[3:0] == 4'b1001) & (~run)) // Read @ $ff49 [last of size data]
rxt_res_end <= 1'b1;
if (data_inc)
transfer_address <= transfer_address + 1'b1;
if (transfer_clear)
transfer_address <= 8'h00;
end
end
wire sdc_fail, sdc_ready, sdc_busy;
localparam CMD_READ = 5'b10000;
localparam CMD_WRITE = 5'b10100;
localparam CMD_EXT = 5'b11000;
reg wr_cmd;
reg ack_d;
reg [23:0] response_reg;
wire end_ack = ~sd_ack[l_drive] & ack_d;
reg l_drive, buffer_upper;
reg time_clr;
reg [13:0] delay_time;
always @(negedge CLK or negedge RESET_N)
begin
if(!RESET_N)
begin
state <= state_idle;
sdc_ready <= 1'b0;
sdc_busy <= 1'b0;
sd_rd[0] <= 1'b0;
sd_rd[1] <= 1'b0;
sd_wr[0] <= 1'b0;
sd_wr[1] <= 1'b0;
sd_lba[0] <= 32'h00000000;
sd_lba[1] <= 32'h00000000;
run <= 1'b0;
cmd_done <= 1'b0;
wr_cmd <= 1'b0;
ack_d <= 1'b0;
transfer_clear <= 1'b0;
sdc_fail <= 1'b0;
ext_response <= 1'b0;
response_reg <= 24'h000000;
sdc_always <= 1'b0;
sdc_HALT <= 1'b0;
l_drive <= 1'b0;
buffer_upper <= 1'b0;
time_clr <= 1'b1;
delay_time <= 14'b00000000000000;
end
else
begin
new_cmd_d <= new_cmd;
cmd_done <= 1'b0;
ack_d <= sd_ack[l_drive];
delay_time <= delay_time + 1'b1;
if (time_clr)
delay_time <= 14'b00000000000000;
if (rxt_res_end) // If we read ff4b then we've read the ext_response
ext_response <= 1'b0;
case(state)
state_idle:
begin
sdc_busy <= 1'b0;
sdc_ready <= 1'b0;
run <= 1'b0;
wr_cmd <= 1'b0;
time_clr <= 1'b1;
transfer_clear <= 1'b1;
if (new_cmd & ~new_cmd_d)
if (command[7:3] == CMD_READ)
begin
state <= state_read;
end
else if (command[7:3] == CMD_WRITE)
begin
state <= state_read;
end
else if (command[7:3] == CMD_EXT)
begin
state <= state_ext;
end
else // no valid command found
begin
cmd_done <= 1'b1;
sdc_fail <= 1'b1;
end
end
state_read:
begin
sdc_busy <= 1'b1;
buffer_upper <= LSN[0];
l_drive <= command[0];
ext_response <= 1'b0; // If we have not read the ext_response by now we are not going too
transfer_clear <= 1'b0;
run <= 1'b1;
if (command[7:3] == CMD_WRITE)
wr_cmd <= 1'b1;
// Issue sda read command...
if (~command[0]) // This reference to the drive must be to the command register as l_drive has not yet updated
sd_lba[0] <= {8'h00, 1'b0, LSN[23:1]};
else
sd_lba[1] <= {8'h00, 1'b0, LSN[23:1]};
state <= state_r1;
end
state_r1:
begin
sd_rd[l_drive] <= 1'b1;
state <= state_r1a;
end
state_r1a:
if (sd_ack[l_drive])
begin
sd_rd[l_drive] <= 1'b0;
state <= state_r3;
end
state_r3:
begin
if (sd_ack[l_drive] & sd_buff_wr & (sd_buff_addr == 9'b111111111)) // wait for the last ack
begin
sdc_ready <= 1'b1;
if (wr_cmd)
state <= state_write;
else
state <= state_r4;
end
end
state_r4:
begin
if ((transfer_address == 8'hff) & CLK_EN & SDC_RD & (ADDRESS[3:1] == 3'b101)) // wait for the last read
begin
cmd_done <= 1'b1;
sdc_ready <= 1'b0;
sdc_busy <= 1'b0;
state <= state_idle;
end
end
state_write:
begin
if ((transfer_address == 8'hff) & CLK_EN & SDC_WR & (ADDRESS[3:1] == 3'b101)) // wait for the last write
begin
state <= state_w1;
end
end
state_w1:
begin
sdc_HALT <= 1'b1;
sd_wr[l_drive] <= 1'b1;
state <= state_w1a;
end
state_w1a:
if (sd_ack[l_drive])
begin
sd_wr[l_drive] <= 1'b0;
state <= state_w3;
end
state_w3:
begin
time_clr <= 1'b1;
if (end_ack) // wait for the end of ack...
begin
state <= state_w4;
end
end
state_w4:
begin
time_clr <= 1'b0;
if (delay_time[13]) // wait for .1ms...
begin
sdc_HALT <= 1'b0;
wr_cmd <= 1'b0;
cmd_done <= 1'b1;
sdc_ready <= 1'b0;
sdc_busy <= 1'b0;
state <= state_idle;
end
end
state_ext:
begin
if (LSN[23:16] == 8'H51) // This is q [Query]
begin
sdc_busy <= 1'b1;
state <= state_e1;
end
else if (LSN[23:16] == 8'H67) // This is g [Disable FDC emulation] [Used by OS9]
begin
cmd_done <= 1'b1;
sdc_always <= 1'b1; // Disable floppy
state <= state_idle;
end
else
begin
cmd_done <= 1'b1; // All other ext commands...
sdc_fail <= 1'b1;
state <= state_idle;
end
end
state_e1:
begin
ext_response <= 1'b1;
`ifdef CoCo3_sdc_override_size
// response_reg <= 24'h555555; // This fixes a redirect error in OS9EOU - Value=no hardware
response_reg <= 24'h404040; // This fixes a redirect error in OS9EOU - Value=no hardware
`else
response_reg <= drive_size[l_drive][31:8]; // This returns the correct size of the mounted drive in sectors
`endif
state <= state_e2;
end
state_e2:
begin
sdc_busy <= 1'b0;
cmd_done <= 1'b1;
state <= state_idle;
end
endcase
end
end
wire [7:0] hd_buff_data;
wire [7:0] sd_buf_out;
// Both drives cannot be executing a read or write at the same time. Both use the same sd sector buffer
assign sd_buff_din[0] = sd_buf_out;
assign sd_buff_din[1] = sd_buf_out;
sdc_dpram hd_buff
(
.clock(CLK),
.address_a(sd_buff_addr),
.data_a(sd_buff_dout),
.wren_a(sd_buff_wr & sd_ack[l_drive]),
.q_a(sd_buf_out),
.address_b({buffer_upper, transfer_address}),
.data_b(SDC_DATA_IN),
.wren_b(SDC_EN & CLK_EN & SDC_WR & (ADDRESS[3:1] == 3'b101)),
.q_b(hd_buff_data)
);
wire [7:0] sdc_status;
assign sdc_status = {sdc_fail, drive_wp[l_drive], 1'b0, ~drive_ready[l_drive], 2'b00, sdc_ready, sdc_busy};
assign SDC_READ_DATA = (ADDRESS == ADRS_FF42) ? {sdc_data_reg, 4'h0}:
(ADDRESS == ADRS_FF43) ? sdc_status_reg:
(ADDRESS == ADRS_FF48) ? sdc_status:
(ADDRESS == ADRS_FF49) ? response_reg[23:16]:
((ADDRESS == ADRS_FF4A) & ~ext_response) ? hd_buff_data:
((ADDRESS == ADRS_FF4A) & ext_response) ? response_reg[15:8]:
((ADDRESS == ADRS_FF4B) & ~ext_response) ? hd_buff_data:
((ADDRESS == ADRS_FF4B) & ext_response) ? response_reg[7:0]:
8'h00;
endmodule
module sdc_dpram
(
input clock,
input [8:0] address_a,
input [7:0] data_a,
input wren_a,
output reg [7:0] q_a,
input [8:0] address_b,
input [7:0] data_b,
input wren_b,
output reg [7:0] q_b
);
logic [7:0] ram[0:511];
always_ff@(posedge clock) begin
if(wren_a) begin
ram[address_a] <= data_a;
q_a <= data_a;
end else begin
q_a <= ram[address_a];
end
end
always_ff@(posedge clock) begin
if(wren_b) begin
ram[address_b] <= data_b;
q_b <= data_b;
end else begin
q_b <= ram[address_b];
end
end
endmodule