Files
CoCo3_Plus_MiSTer/rtl/sdc_top.sv
shodge12 7e58577658 2023 - 5.1 init...
CTF = Compile Time Feature...

1.	Interrupt system restored to previous code - improved compadibility.
2.	Changed to cycle accurate 6809 (Greg Miller) at speeds up to 9.56Mhz. [CTF]
3.	Recoded sdc and fdc to only have one instance of the wd1773.
4.	Re-added software disable in sdc [Ext 'g'].
5.	Recoded Cartridge bank switching to only exist when MiSTer slot 3 is selected. [removed soft multipak select]
6.	Moved CoCo Hardware RS-232 from always existing to only existing in multipak slot 1.
7.	Changed ADRS (SDS sig) decoding to = FF40-FF5f per hardware.
8.	Fixed coding problem in os9 driver llcocosdc to work with MPI properly. [CTF]
9.	Set default disk size to constant $555555 to fix os9 redirect problem. [CTF]
10	Disabled GART [GIMEX hardware DMA] to prevent OS9 from detecting GIMEX. [CTF]
11	Corrected missing begin statement in master timing loop.
12.	Fixed Donkey King DAPD issue in Tom Mix program [DPAD now moved joysticks to limits under dpad
13. Fixed incorrect addressing of FE00-FEFF for CARTs which gets PITFALL and RAMPAGE working
To Do
0.	Update framework
2023-10-23 19:35:57 -04:00

520 lines
14 KiB
Systemverilog

////////////////////////////////////////////////////////////////////////////////
// Project Name: COCO3 Targeting MISTer
// File Name: sdc_top.sv
//
// CoCo SDC TOP Controller for MISTer
//
////////////////////////////////////////////////////////////////////////////////
//
//
// CoCo SDC TOP Controller (sdc_top.sv) by Stan Hodge ([email protected])
// Copyright (c) 2022 by Stan Hodge ([email protected])
//
// All rights reserved
// Redistribution and use in source and synthezised forms, with or without
// modification, are permitted provided that the following conditions are met:
//
// Redistributions of source code must retain the above copyright notice,
// this list of conditions and the following disclaimer.
//
// Redistributions in synthesized form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the distribution.
//
// Neither the name of the author nor the names of other contributors may
// be used to endorse or promote products derived from this software without
// specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
// THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
// PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
// CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
// POSSIBILITY OF SUCH DAMAGE.
//
// Please report bugs to the author, but before you do so, please
// make sure that this is not a derivative work and that
// you have the latest version of this file.
//
// This is a full FDC controller for 2 floppy drives. It also has a 2 drive
// cocosdc imbedded. When booting with a superfloppy, the floppy portion
// of this controller will be shutdown and the normal 4 drive fdc will take
// over dfc on a different mpi slot.
//
// Ver 2.00 Implemented with single 1793 ...
//
////////////////////////////////////////////////////////////////////////////////
////////////////////////////////////////////////////////////////////////////////
module sdc_top(
input CLK, // clock
input RESET_N, // async reset
input [3:0] ADDRESS, // i/o port addr [extended for coco]
input CLK_EN,
input [7:0] DATA_IN, // data in
output [7:0] DATA_HDD, // data out
output HALT, // DMA request
output NMI_09,
// FDC host r/w handling
input FF40_CLK, // FDC Write support
input FF40_ENA,
input SDC_EN_CS, // FDC Read Data support
input WD1793_RD,
input WD1793_WR_CTRL, // 1793 RD & WR control signal generation
input WD1793_RD_CTRL,
// SDC I/O
input SDC_REG_W_ENA,
input SDC_REG_READ,
output ext_response,
// SD block level interface
input [1:0] img_mounted, // signaling that new image has been mounted
input img_readonly, // mounted as read only. valid only for active bit in img_mounted
input [63:0] img_size, // size of image in bytes.
output [31:0] sd_lba[2],
output [5:0] sd_blk_cnt[2], // number of blocks-1, total size ((sd_blk_cnt+1)*(1<<(BLKSZ+7))) must be <= 16384!
output reg [1:0] sd_rd,
output reg [1:0] sd_wr,
input [1:0] sd_ack,
// SD byte level access. Signals for 2-PORT altsyncram.
input [8:0] sd_buff_addr,
input [7:0] sd_buff_dout,
output [7:0] sd_buff_din[2],
input sd_buff_wr
);
wire [7:0] DRIVE_SEL_EXT;
wire MOTOR;
wire WRT_PREC;
wire DENSITY;
wire HALT_EN;
// Diagnostics only
//assign probe = {2'd0, HALT_EN_RST, sd_buff_wr, WR[0], RD[0], HALT_EN, HALT};
// Generate a 8.333 Mhz enable for the fdc... and control writes
wire ena_8Mhz;
wire [5:0] div_8mhz;
assign ena_8Mhz = (div_8mhz == 6'd5) ? 1'b1: 1'b0;
always@(negedge CLK or negedge RESET_N)
begin
if (~RESET_N) div_8mhz <= 6'd0;
else
begin
if (ena_8Mhz)
div_8mhz <= 6'd0;
else
div_8mhz <= div_8mhz + 6'd1;
end
end
localparam SDC_MAGIC_CMD = 8'h43;
wire sdc_always;
wire [7:0] FF40_READ_VALUE = {HALT_EN, DRIVE_SEL_EXT[3], DENSITY, WRT_PREC, MOTOR, DRIVE_SEL_EXT[2:0]};
wire SDC_EN = ((FF40_READ_VALUE == SDC_MAGIC_CMD) | sdc_always);
wire [7:0] SDC_READ_DATA;
wire FF40_RD = ({SDC_EN_CS, ADDRESS[3:0]} == 5'b10000);
//FDC read data path. =$ff40 or wd1793(s)
assign DATA_HDD =
(FF40_RD) ? FF40_READ_VALUE:
(SDC_EN | ext_response) ? SDC_READ_DATA:
(SDC_EN_CS & (ADDRESS[3:1] == 3'b001)) ? SDC_READ_DATA: // FF42 & FF43
(WD1793_RD) ? DATA_1793: //(1793[s])
8'h00;
wire [31:0] sdc_sd_lba[2];
wire [31:0] fdc_sd_lba[2];
wire [31:0] wd1793_sd_lba;
wire [1:0] sdc_sd_rd;
wire wd1793_sd_rd;
wire [1:0] fdc_sd_rd;
wire [1:0] sdc_sd_wr;
wire [1:0] fdc_sd_wr;
wire wd1793_sd_wr;
wire [7:0] sdc_sd_buff_din[2];
wire [7:0] fdc_sd_buff_din[2];
wire [7:0] wd1793_sd_buff_din;
wire wd1793_sd_ack;
wire sdc_HALT;
assign sd_lba[0:1] = SDC_EN ? sdc_sd_lba[0:1]:
fdc_sd_lba[0:1];
assign fdc_sd_lba[0] = wd1793_sd_lba;
assign fdc_sd_lba[1] = wd1793_sd_lba;
assign sd_rd[1:0] = SDC_EN ? sdc_sd_rd[1:0]:
fdc_sd_rd[1:0];
assign fdc_sd_rd[0] = (drive_index == 3'd1) ? wd1793_sd_rd:
1'b0;
assign fdc_sd_rd[1] = (drive_index == 3'd2) ? wd1793_sd_rd:
1'b0;
assign sd_wr[1:0] = SDC_EN ? sdc_sd_wr[1:0]:
fdc_sd_wr[1:0];
assign fdc_sd_wr[0] = (drive_index == 3'd1) ? wd1793_sd_wr:
1'b0;
assign fdc_sd_wr[1] = (drive_index == 3'd2) ? wd1793_sd_wr:
1'b0;
assign sd_buff_din[0:1] = SDC_EN ? sdc_sd_buff_din[0:1]:
fdc_sd_buff_din[0:1];
assign fdc_sd_buff_din[0] = wd1793_sd_buff_din;
assign fdc_sd_buff_din[1] = wd1793_sd_buff_din;
assign wd1793_sd_ack = (drive_index == 3'd1) ? sd_ack[0]:
(drive_index == 3'd2) ? sd_ack[1]:
sd_ack[0]; // default is drive 1
sdc coco_sdc(
.CLK(CLK), // clock
.RESET_N(RESET_N), // async reset
.ADDRESS(ADDRESS), // i/o port addr [extended for coco]
.SDC_DATA_IN(DATA_IN), // data in
.SDC_READ_DATA(SDC_READ_DATA), // data out
.SDC_EN(SDC_EN), // SDC is active [input to sdc]
.CLK_EN(CLK_EN),
.SDC_WR(SDC_REG_W_ENA),
.SDC_RD(SDC_REG_READ),
.sdc_HALT(sdc_HALT),
.ext_response(ext_response),
.sdc_always(sdc_always),
// SD block level interface
.sd_lba(sdc_sd_lba[0:1]),
.sd_rd(sdc_sd_rd[1:0]),
.sd_wr(sdc_sd_wr[1:0]),
.sd_ack(sd_ack[1:0]),
// Drive descripters
.drive_wp(drive_wp),
.drive_ready(drive_ready),
.drive_size(drive_size[0:1]),
// SD byte level access. Signals for 2-PORT altsyncram.
.sd_buff_addr(sd_buff_addr),
.sd_buff_dout(sd_buff_dout),
.sd_buff_din(sdc_sd_buff_din[0:1]),
.sd_buff_wr(sd_buff_wr)
);
// $ff40 control register [part 1]
wire [3:0] DRIVE_SEL_EXT_PRE = {DATA_IN[6] // Side Select
, DATA_IN[2:0]}; // ONLY 2 drives (DS)
reg [2:0] drive_index;
// SD blk system is a array of 4 systems - one for each drive.
// 'drive_index' identifies which controller is addressd.
// drive 1-2 for the sdc is denoted as 1 , 2 [0 is no drive selected]
always @(negedge FF40_CLK or negedge RESET_N)
begin
if(!RESET_N)
begin
DRIVE_SEL_EXT <= 8'h00;
MOTOR <= 1'b0;
WRT_PREC <= 1'b0;
DENSITY <= 1'b0;
drive_index <= 3'd0;
end
else
begin
if (FF40_ENA)
begin
DRIVE_SEL_EXT <= {4'b0000, DRIVE_SEL_EXT_PRE};
MOTOR <= DATA_IN[3]; // Turn on motor, not used here just checked, 0=MotorOff 1=MotorOn
WRT_PREC <= DATA_IN[4]; // Write Precompensation, not used here
DENSITY <= DATA_IN[5]; // Density, not used here just checked
case(DRIVE_SEL_EXT_PRE)
4'b0010:
drive_index <= 3'd2;
4'b0001:
drive_index <= 3'd1;
4'b1010:
drive_index <= 3'd2;
4'b1001:
drive_index <= 3'd1;
4'b1011: // This is what the Magic Number $43 does so we select a non-active drive
drive_index <= 3'd0;
4'b1000: // This is no drive with DS = illegal drive
drive_index <= 3'd0;
4'b0000: // This is no drive (maybe 0 in ff40) = illegal drive
drive_index <= 3'd0;
default:
drive_index <= 3'd0;
endcase
end
end
end
// $ff40 control register [part 2]
always @(negedge FF40_CLK or negedge HALT_EN_RST)
begin
if(!HALT_EN_RST)
begin
HALT_EN <= 1'b0;
end
else
begin
if (FF40_ENA)
begin
HALT_EN <= DATA_IN[7]; // Normal Halt enable, 0=Disabled 1=Enabled
if (sdc_always)
HALT_EN <= 1'b0;
end
end
end
// Control signals for the wd1793
wire selected_DRQ;
wire selected_INTRQ;
wire WR;
wire RD;
wire RD_E;
wire HALT_EN_RST;
wire [7:0] DATA_1793;
reg read;
reg write;
reg read_d;
reg write_d;
reg [7:0] DATA_IN_L;
reg r_w_active;
reg clk_8Mhz_enable_found;
reg read1;
reg write1;
reg [1:0] ADDRESS_L;
assign RD = (read || RD_E); // Even with no drive selected allow read to the controller
// The idea here is to "stretch" the CPU read and write signals to ensure we catch a 8 mhz enable.
// For writes we will buffer the data out to ensure it does not go away.
// For reads it is expected that data is available asynchronusly at the cpu rate and the only reason to catch a
// 8Mhz edge is to update pointer and misc flags.
// This is very nasty code and will likely only work with the present CPU timing.
// It is heavily dependant on address and write data being available just after
// the previous cycle.
wire wd1793_r_w_sync_rst = RESET_N;
always @(negedge CLK or negedge wd1793_r_w_sync_rst)
begin
if(!wd1793_r_w_sync_rst)
begin
read_d <= 1'b0;
write_d <= 1'b0;
r_w_active <= 1'b0;
clk_8Mhz_enable_found <= 1'b0;
WR <= 1'b0;
RD_E <= 1'b0;
read1 <= 1'b0;
write1 <= 1'b0;
read <= 1'b0;
write <= 1'b0;
end
else
begin
// synchronizers
read1 <= WD1793_RD_CTRL & ~SDC_EN;
read <= read1;
write1 <= WD1793_WR_CTRL & ~SDC_EN;
write <= write1;
// delays for edge detection
read_d <= read;
write_d <= write;
if ((read1 & ~read) | (write1 & ~write))
begin
// Latch Address & Data
ADDRESS_L <= ADDRESS[1:0];
DATA_IN_L <= DATA_IN;
end
// Synchronus rising edge of write
if ((write == 1'b1) && (write_d == 1'b0))
begin
// Set Write
r_w_active <= 1'b1;
WR <= 1'b1;
end
// Synchronus rising edge of read
if ((read == 1'b1) && (read_d == 1'b0))
begin
r_w_active <= 1'b1;
RD_E <= 1'b1;
end
// Clears
if (ena_8Mhz && r_w_active)
clk_8Mhz_enable_found <= 1'b1;
// 1 50Mhz clock later...
if (clk_8Mhz_enable_found)
begin
clk_8Mhz_enable_found <= 1'b0;
r_w_active <= 1'b0;
WR <= 1'b0;
RD_E <= 1'b0;
end
end
end
// NMI from disk controller
assign NMI_09 = ~SDC_EN & DENSITY & selected_INTRQ; // Send NMI if Double Density (Halt Mode)
// HALT from disk controller
assign HALT = (~SDC_EN & HALT_EN & ~selected_DRQ) | sdc_HALT;
assign HALT_EN_RST = RESET_N & ~selected_INTRQ; // From controller schematic
// The SD_BLK interface and thus the wd1793 will allways transfer 1 blk. This is blk qty - 1 per spec.
assign sd_blk_cnt[1] = 6'd0;
assign sd_blk_cnt[0] = 6'd0;
reg drive_wp[2];
reg [1:0] drive_ready = 2'b00;
reg [1:0] double_sided = 2'b00;
reg [31:0] drive_size[2];
wire [31:0] selected_drive_size;
wire selected_drive_ready, selected_drive_wp, selected_double_sided;
// As drives are mounted in MISTer this logic saves the write protect and generates ready for
// changing drives to the wd1793.
// This can also get the disk size to properly handle DS drives - TBD
// Reset of drive wp to a default of 1 removed because of persistance.
// Drive 0
always @(negedge img_mounted[0])
begin
drive_wp[0] <= img_readonly;
drive_ready[0] <= 1'b1;
drive_size[0] <= img_size[31:0]; //Size / 256 on [31:8]
double_sided[0]<= (img_size > 64'd368600) & (img_size < 64'd740000);//20'd368640;
end
// Drive 1
always @(negedge img_mounted[1])
begin
drive_wp[1] <= img_readonly;
drive_ready[1] <= 1'b1;
drive_size[1] <= img_size[31:0]; //Size / 256 on [31:8]
double_sided[1]<= (img_size > 64'd368600) & (img_size < 64'd740000);//20'd368640;
end
assign selected_drive_size = (drive_index == 3'd1) ? drive_size[0]:
(drive_index == 3'd2) ? drive_size[1]:
drive_size[0]; // default is drive 1
assign selected_drive_wp = (drive_index == 3'd1) ? drive_wp[0]:
(drive_index == 3'd2) ? drive_wp[1]:
drive_wp[0]; // default is drive 1
assign selected_double_sided= (drive_index == 3'd1) ? double_sided[0]:
(drive_index == 3'd2) ? double_sided[1]:
double_sided[0]; // default is drive 1
assign selected_drive_ready = (drive_index == 3'd1) ? drive_ready[0]:
(drive_index == 3'd2) ? drive_ready[1]:
drive_ready[0]; // default is drive 1
wd1793 #(1,0) coco_wd1793_sdc
(
.clk_sys(~CLK),
.ce(ena_8Mhz),
.reset(~RESET_N),
.io_en(1'b1),
.rd(RD),
.wr(WR),
.addr(ADDRESS_L[1:0]),
.din(DATA_IN_L),
.dout(DATA_1793),
.drq(selected_DRQ),
.intrq(selected_INTRQ),
.img_mounted(1'b0), // Not used when using _override
.img_mounted_overide(1'b1), // Load img_size and layout on each clock
.img_size(selected_drive_size[19:0]),
.sd_lba(wd1793_sd_lba),
.sd_rd(wd1793_sd_rd),
.sd_wr(wd1793_sd_wr),
.sd_ack(wd1793_sd_ack),
.sd_buff_addr(sd_buff_addr),
.sd_buff_dout(sd_buff_dout),
.sd_buff_din(wd1793_sd_buff_din),
.sd_buff_wr(sd_buff_wr),
.wp(selected_drive_wp),
.size_code(3'd5), // 5 is 18 sector x 256 bits COCO standard
.layout(~selected_double_sided), // 0 = Track-Side-Sector, 1 - Side-Track-Sector
.side(selected_double_sided & DRIVE_SEL_EXT[3]),
.ready(selected_drive_ready),
.input_active(0), // Section not used
.input_addr(0),
.input_data(0),
.input_wr(0),
.buff_din(0)
);
endmodule