//////////////////////////////////////////////////////////////////////////////// // Project Name: CoCo3FPGA Version 5.0 // File Name: UIM.v // // CoCo3 in an FPGA // //////////////////////////////////////////////////////////////////////////////// // //////////////////////////////////////////////////////////////////////////////// // // Color Computer 3 compatible system on a chip // // // Copyright (c) 2008 Gary Becker (gary_l_becker@yahoo.com) // // All rights reserved // // Redistribution and use in source and synthezised forms, with or without // modification, are permitted provided that the following conditions are met: // // Redistributions of source code must retain the above copyright notice, // this list of conditions and the following disclaimer. // // Redistributions in synthesized form must reproduce the above copyright // notice, this list of conditions and the following disclaimer in the // documentation and/or other materials provided with the distribution. // // Neither the name of the author nor the names of other contributors may // be used to endorse or promote products derived from this software without // specific prior written permission. // // THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" // AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, // THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR // PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE // LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR // CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF // SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS // INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN // CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) // ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE // POSSIBILITY OF SUCH DAMAGE. // // Please report bugs to the author, but before you do so, please // make sure that this is not a derivative work and that // you have the latest version of this file. // // //////////////////////////////////////////////////////////////////////////////// // Stan Hodge // // UART Injection Module by Stan Hodge 11/8/26 // // This module uses the AMW_END chain to cause a $FF to be written to the 6551 // uart, then delay until that transmission has been made, then pass on the AMW_END. // This only occurs in slot 1. In other slots, AMW_END_OUT = AMW_END_IN. // //////////////////////////////////////////////////////////////////////////////// module UIM( input CLK, input RESET_N, input [1:0] MPI_SCS, input PH_2, input AMW_END_IN, input ENABLE_IN, input RW_N_IN, input [1:0] ADDRESS_IN, input [7:0] DATA_IN, output AMW_END_OUT, output ENABLE_OUT, output RW_N_OUT, output [1:0] ADDRESS_OUT, output [7:0] DATA_OUT ); //////////////////////////////////////////////////////////// localparam UIM_START = 3'd0; localparam UIM_F1 = 3'd1; localparam UIM_F2 = 3'd2; localparam UIM_F3 = 3'd3; localparam UIM_F4 = 3'd4; localparam UIM_F5 = 3'd5; localparam UIM_F6 = 3'd6; localparam UIM_ST_END = 3'd7; reg [2:0] state; reg mux,rw,ena,timer_ena, AMW_END_OUT_ST; reg [13:0] timer; assign ADDRESS_OUT = (mux == 1'b0) ? ADDRESS_IN: 2'b00; assign DATA_OUT = (mux == 1'b0) ? DATA_IN: 8'b11111111; assign RW_N_OUT = (mux == 1'b0) ? RW_N_IN: rw; assign ENABLE_OUT = (mux == 1'b0) ? ENABLE_IN: ena; assign AMW_END_OUT = (MPI_SCS == 2'b00) ? AMW_END_OUT_ST: AMW_END_IN; always @(negedge CLK or negedge RESET_N) begin if(!RESET_N) begin state <= UIM_START; mux <= 1'b0; rw <= 1'b1; ena <= 1'b0; timer <= 14'b00000000000000; timer_ena <=1'b0; AMW_END_OUT_ST <= 1'b0; end else begin if (timer_ena == 1'b1) timer <= timer + 1'b1; case(state) UIM_START: begin if ((MPI_SCS == 2'b00) && (AMW_END_IN == 1'b1)) state <= UIM_F1; end UIM_F1: begin mux <= 1'b1; state <= UIM_F2; end UIM_F2: begin ena <= 1'b1; state <= UIM_F3; end UIM_F3: begin rw <= 1'b0; state <= UIM_F4; end UIM_F4: begin if (PH_2) begin rw <= 1'b1; state <= UIM_F5; end end UIM_F5: begin ena <= 1'b0; state <= UIM_F6; end UIM_F6: begin mux <= 1'b0; timer_ena <= 1'b1; state <= UIM_ST_END; end UIM_ST_END: begin if (timer[13] == 1'b1) begin AMW_END_OUT_ST <= 1'b1; timer_ena <= 1'b0; end end default:; endcase end end endmodule