//============================================================================ // CoCo3 port to MiSTer // Copyright (c) 2019 Alan Steremberg - alanswx // // //============================================================================ module emu ( //Master input clock input CLK_50M, //Async reset from top-level module. //Can be used as initial reset. input RESET, //Must be passed to hps_io module inout [48:0] HPS_BUS, //Base video clock. Usually equals to CLK_SYS. output CLK_VIDEO, //Multiple resolutions are supported using different CE_PIXEL rates. //Must be based on CLK_VIDEO output CE_PIXEL, //Video aspect ratio for HDMI. Most retro systems have ratio 4:3. //if VIDEO_ARX[12] or VIDEO_ARY[12] is set then [11:0] contains scaled size instead of aspect ratio. output [12:0] VIDEO_ARX, output [12:0] VIDEO_ARY, output [7:0] VGA_R, output [7:0] VGA_G, output [7:0] VGA_B, output VGA_HS, output VGA_VS, output VGA_DE, // = ~(VBlank | HBlank) output VGA_F1, output [1:0] VGA_SL, output VGA_SCALER, // Force VGA scaler input [11:0] HDMI_WIDTH, input [11:0] HDMI_HEIGHT, output HDMI_FREEZE, `ifdef MISTER_FB // Use framebuffer in DDRAM (USE_FB=1 in qsf) // FB_FORMAT: // [2:0] : 011=8bpp(palette) 100=16bpp 101=24bpp 110=32bpp // [3] : 0=16bits 565 1=16bits 1555 // [4] : 0=RGB 1=BGR (for 16/24/32 modes) // // FB_STRIDE either 0 (rounded to 256 bytes) or multiple of pixel size (in bytes) output FB_EN, output [4:0] FB_FORMAT, output [11:0] FB_WIDTH, output [11:0] FB_HEIGHT, output [31:0] FB_BASE, output [13:0] FB_STRIDE, input FB_VBL, input FB_LL, output FB_FORCE_BLANK, `ifdef MISTER_FB_PALETTE // Palette control for 8bit modes. // Ignored for other video modes. output FB_PAL_CLK, output [7:0] FB_PAL_ADDR, output [23:0] FB_PAL_DOUT, input [23:0] FB_PAL_DIN, output FB_PAL_WR, `endif `endif output LED_USER, // 1 - ON, 0 - OFF. // b[1]: 0 - LED status is system status OR'd with b[0] // 1 - LED status is controled solely by b[0] // hint: supply 2'b00 to let the system control the LED. output [1:0] LED_POWER, output [1:0] LED_DISK, // I/O board button press simulation (active high) // b[1]: user button // b[0]: osd button output [1:0] BUTTONS, input CLK_AUDIO, // 24.576 MHz output [15:0] AUDIO_L, output [15:0] AUDIO_R, output AUDIO_S, // 1 - signed audio samples, 0 - unsigned output [1:0] AUDIO_MIX, // 0 - no mix, 1 - 25%, 2 - 50%, 3 - 100% (mono) //ADC inout [3:0] ADC_BUS, //SD-SPI output SD_SCK, output SD_MOSI, input SD_MISO, output SD_CS, input SD_CD, //High latency DDR3 RAM interface //Use for non-critical time purposes output DDRAM_CLK, input DDRAM_BUSY, output [7:0] DDRAM_BURSTCNT, output [28:0] DDRAM_ADDR, input [63:0] DDRAM_DOUT, input DDRAM_DOUT_READY, output DDRAM_RD, output [63:0] DDRAM_DIN, output [7:0] DDRAM_BE, output DDRAM_WE, //SDRAM interface with lower latency output SDRAM_CLK, output SDRAM_CKE, output [12:0] SDRAM_A, output [1:0] SDRAM_BA, inout [15:0] SDRAM_DQ, output SDRAM_DQML, output SDRAM_DQMH, output SDRAM_nCS, output SDRAM_nCAS, output SDRAM_nRAS, output SDRAM_nWE, `ifdef MISTER_DUAL_SDRAM //Secondary SDRAM //Set all output SDRAM_* signals to Z ASAP if SDRAM2_EN is 0 input SDRAM2_EN, output SDRAM2_CLK, output [12:0] SDRAM2_A, output [1:0] SDRAM2_BA, inout [15:0] SDRAM2_DQ, output SDRAM2_nCS, output SDRAM2_nCAS, output SDRAM2_nRAS, output SDRAM2_nWE, `endif input UART_CTS, output UART_RTS, input UART_RXD, output UART_TXD, output UART_DTR, input UART_DSR, // Open-drain User port. // 0 - D+/RX // 1 - D-/TX // 2..6 - USR2..USR6 // Set USER_OUT to 1 to read from USER_IN. input [6:0] USER_IN, output [6:0] USER_OUT, input OSD_STATUS ); //`define SOUND_DBG //assign CE_PIXEL=1; //assign {UART_RTS, UART_TXD, UART_DTR} = 0; assign {SD_SCK, SD_MOSI, SD_CS} = 'Z; //assign USER_OUT = '1; assign {DDRAM_CLK, DDRAM_BURSTCNT, DDRAM_ADDR, DDRAM_DIN, DDRAM_BE, DDRAM_RD, DDRAM_WE} = 0; assign ADC_BUS = 'Z; //assign {SDRAM_DQ, SDRAM_A, SDRAM_BA, SDRAM_CLK, SDRAM_CKE, SDRAM_DQML, SDRAM_DQMH, SDRAM_nWE, SDRAM_nCAS, SDRAM_nRAS, SDRAM_nCS} = 'Z; assign BUTTONS = 0; assign VGA_F1 = 0; //assign USER_OUT = '1; assign LED_USER = ioctl_download; assign LED_DISK = 0; assign LED_POWER = 0; assign VGA_SCALER = 0; assign HDMI_FREEZE = 0; wire [1:0] ar = status[9:8]; assign VIDEO_ARX = (!ar) ? 12'd4 : (ar - 1'd1); assign VIDEO_ARY = (!ar) ? 12'd3 : 12'd0; `include "build_id.v" localparam CONF_STR = { "COCO3;UART19200:9600:4800:2400:1200:300;", "-;", //"OCD,Multi-Pak Slot,Orch 90,ECB / Cart,Disk;", "OCD,Multi-Pak Slot,(Slot3) ECB /Cart,(Slot 4) Disk;", "-;", "H2S0,DSKVHD,Load Disk Drive 0;", "H2S1,DSKVHD,Load Disk Drive 1;", "H2S2,DSK,Load Disk Drive 2;", "H2S3,DSK,Load Disk Drive 3;", "-;", "H1F1,CCC,Load Cartridge;", "-;", "F2,CAS,Load Cassette;", "TF,Stop & Rewind;", "OH,Monitor Tape Sound,No,Yes;", "-;", "P1,Video Settings;", "P1-;", "P1-, -= Video Settings =-;", "P1-;", "P1O89,Aspect ratio,Original,Full Screen,[ARC1],[ARC2];", "P1O35,Scandoubler Fx,None,HQ2x,CRT 25%,CRT 50%,CRT 75%;", "P1OL,Artifact Color,Off - SG4,On - SG6;", "P1OI,Artifact Color Set,0,1;", "-;", "P2,Debug Menu;", "P2-;", "P2-, -= Debug Menu =-;", "P2-;", "P2F3,BIN,Load COCO Font;", "P2OG,Cart Interrupt Disabled,OFF,ON;", //P2O?,Force Disk 0 DS,Off,On;" //P2O?,Force Disk 1 DS,Off,On;" "-;", "ON,D-Pad Joystick emu,No,Yes;", "O6,Swap Joysticks,Off,On;", "RA,Easter Egg;", "-;", "OO,Force Turbo,No,Yes;", "OJK,Turbo Speed,1.78 Mhz,3.58 Mhz,7.16 Mhz, NA;", "OPR,Memory Size,512K,1M,2M,16M;", "-;", "RM,Cold Boot;", "R0,Reset;", "J,Button1,Button2;", "jn,A,B;", "V,v",`BUILD_DATE }; //////////////////// CLOCKS /////////////////// wire clk_sys; assign clk_sys=CLK_57; wire pll_locked, pll2_locked; wire CLK_114, CLK_57, CLK_28, CLK_14; pll pll ( .refclk(CLK_50M), .rst(0), .outclk_0(CLK_114), .outclk_1(CLK_57), .outclk_2(CLK_28), .outclk_3(CLK_14), .locked(pll2_locked) ); /////////////////////////////////////////////////// wire [31:0] status; wire [1:0] buttons; wire forced_scandoubler; wire direct_video; wire ioctl_download; wire [7:0] ioctl_index; wire ioctl_wr; wire [24:0] ioctl_addr; wire [7:0] ioctl_data; wire [10:0] ps2_key; wire [31:0] joy1, joy2; wire [15:0] joya1, joya2; wire [21:0] gamma_bus; assign CLK_VIDEO = clk_sys; wire [64:0] RTC; // SD - 4 drives 512 size blocks [the wd1793 translates to a 256 byte sector size] hps_io #(.CONF_STR(CONF_STR),.PS2DIV(2400), .VDNUM(4), .BLKSZ(2)) hps_io ( .clk_sys(clk_sys), // .clk_sys(CLK_50M), (SRH) .HPS_BUS(HPS_BUS), .buttons(buttons), .status(status), .status_menumask({ (mpi != 2'b11), (mpi != 2'b10),direct_video}), .forced_scandoubler(forced_scandoubler), .RTC(RTC), .gamma_bus(gamma_bus), .direct_video(direct_video), .ioctl_download(ioctl_download), .ioctl_wr(ioctl_wr), .ioctl_addr(ioctl_addr), .ioctl_dout(ioctl_data), .ioctl_index(ioctl_index), // SD block level interface .img_mounted(img_mounted), // signaling that new image has been mounted .img_readonly(img_readonly), // mounted as read only. valid only for active bit in img_mounted .img_size(img_size), // size of image in bytes. .sd_lba(sd_lba), .sd_blk_cnt(sd_blk_cnt), // number of blocks-1, total size ((sd_blk_cnt+1)*(1<<(BLKSZ+7))) must be <= 16384! .sd_rd(sd_rd), .sd_wr(sd_wr), .sd_ack(sd_ack), // SD byte level access. Signals for 2-PORT altsyncram. .sd_buff_addr(sd_buff_addr), .sd_buff_dout(sd_buff_dout), .sd_buff_din(sd_buff_din), .sd_buff_wr(sd_buff_wr), .joystick_0(joy1), .joystick_1(joy2), .joystick_l_analog_0(joya1), .joystick_l_analog_1(joya2), .ps2_key(ps2_key), .ps2_kbd_clk_out ( ps2_kbd_clk ), .ps2_kbd_data_out ( ps2_kbd_data ) ); // SD block level interface wire [3:0] img_mounted; wire img_readonly; wire [63:0] img_size; wire [31:0] sd_lba[4]; wire [3:0] sd_blk_cnt[4]; wire [3:0] sd_rd; wire [3:0] sd_wr; wire [3:0] sd_ack; // SD byte level access. Signals for 2-PORT altsyncram. wire [8:0] sd_buff_addr; wire [7:0] sd_buff_dout; wire [7:0] sd_buff_din[4]; wire sd_buff_wr; wire [9:0] center_joystick_y1 = 8'd128 + joya1[15:8]; wire [9:0] center_joystick_x1 = 8'd128 + joya1[7:0]; wire [9:0] center_joystick_y2 = 8'd128 + joya2[15:8]; wire [9:0] center_joystick_x2 = 8'd128 + joya2[7:0]; wire vclk; wire [31:0] coco_joy1 = status[6] ? joy2 : joy1; wire [31:0] coco_joy2 = status[6] ? joy1 : joy2; wire [15:0] coco_ajoy1 = status[6] ? {center_joystick_x2[7:0],center_joystick_y2[7:0]} : {center_joystick_x1[7:0],center_joystick_y1[7:0]}; wire [15:0] coco_ajoy2 = status[6] ? {center_joystick_x1[7:0],center_joystick_y1[7:0]} : {center_joystick_x2[7:0],center_joystick_y2[7:0]}; wire ps2_kbd_clk; wire ps2_kbd_data; wire hblank, vblank; wire hs, vs; wire pix_clk; wire [2:0] scale = status[5:3]; wire [2:0] sl = scale ? scale - 1'd1 : 3'd0; wire scandoubler = (scale || forced_scandoubler); assign VGA_SL = sl[1:0]; wire freeze_sync; video_mixer #(.GAMMA(1)) video_mixer ( .*, .CLK_VIDEO(clk_sys), .ce_pix(pix_clk), .hq2x(scale==1), .R(r), .G(g), .B(b), // Positive pulses. .HSync(hs), .VSync(vs), .HBlank(hblank), .VBlank(vblank) ); // // wire Programmed_RESET_N; wire Programmed_EE; EE_Cold_Bt COCO3_EE_Cold_Bt ( .CLK(CLK_14), .Display_EE(easter_egg), // from MISTer subsystem .Cold_Boot(AMW_ACK), // from AMW system .RESET_to_COCO_N(Programmed_RESET_N), // RESET_N to the coco3 [logically AND'ed to top reset] .EE_to_COCO(Programmed_EE) // Easter Egg to the coco3 ); wire [15:0] audio_left; assign AUDIO_L = { audio_left[15:14], audio_left[13] ^ (status[17] ? casdout : 1'b0),audio_left[12:0]}; //assign AUDIO_R = AUDIO_L; assign AUDIO_S = 0; assign AUDIO_MIX = 0; wire [7:0] r; wire [7:0] g; wire [7:0] b; wire easter_egg = ~status[10]; wire [31:0] probe; assign USER_OUT[6:0] = probe[6:0]; coco3fpga coco3 ( // CLOCKS .CLK_50M(CLK_50M), .CLK_114(CLK_114), .CLK_57(CLK_57), .CLK_28(CLK_28), .CLK_14(CLK_14), // Reset .COCO_RESET_N((~reset & Programmed_RESET_N)), .RED(r), .GREEN(g), .BLUE(b), .EE_N(Programmed_EE), .PHASE(PHASE), .H_SYNC(hs), .V_SYNC(vs), .HBLANK(hblank), .VBLANK(vblank), .PIX_CLK(pix_clk), // PS/2 .ps2_clk(ps2_kbd_clk), .ps2_data(ps2_kbd_data), .joy_use_dpad(digitalJoy), .joy1(coco_joy1), .joy2(coco_joy2), .joya1(coco_ajoy1), .joya2(coco_ajoy2), // R1, L2, R2, L1 .P_SWITCH(~{coco_joy2[4],coco_joy1[5],coco_joy2[5],coco_joy1[4]}), .SWITCH(switch), .SOUND_OUT(cocosound), .SOUND_LEFT(audio_left), .SOUND_RIGHT(AUDIO_R), // Removed offset addition .ioctl_addr(ioctl_addr), .ioctl_data(ioctl_data), .ioctl_download(ioctl_download), .ioctl_index(ioctl_index), .ioctl_wr(ioctl_wr), // SD block level interface .img_mounted(img_mounted), // signaling that new image has been mounted .img_readonly(img_readonly), // mounted as read only. valid only for active bit in img_mounted .img_size(img_size), // size of image in bytes. .sd_lba(sd_lba), .sd_blk_cnt(sd_blk_cnt), // number of blocks-1, total size ((sd_blk_cnt+1)*(1<<(BLKSZ+7))) must be <= 16384! .sd_rd(sd_rd), .sd_wr(sd_wr), .sd_ack(sd_ack), // SD byte level access. Signals for 2-PORT altsyncram. .sd_buff_addr(sd_buff_addr), .sd_buff_dout(sd_buff_dout), .sd_buff_din(sd_buff_din), .sd_buff_wr(sd_buff_wr), .PROBE(probe[31:0]), .clk_Q_out(clk_Q_out), .casdout( casdout), .cas_relay(cas_relay), // SDRAM .sdram_cpu_addr(sdram_cpu_addr), .sdram_dout(sdram_dout), .sdram_cpu_din(sdram_cpu_din), .sdram_cpu_req(sdram_cpu_req), .sdram_cpu_rnw(sdram_cpu_rnw), .sdram_cpu_ack(sdram_cpu_ack), .sdram_cpu_ready(sdram_cpu_ready), .sdram_vid_addr(sdram_vid_addr[24:0]), .sdram_vid_req(sdram_vid_req), .sdram_vid_ack(sdram_vid_ack), .sdram_vid_ready(sdram_vid_ready), .sdram_busy(sdram_busy), .turbo_speed(turbo_speed), .RTC(RTC), .AMW_Trigger(coldboot | mpi_reset | mem_reset), .AMW_ACK(AMW_ACK), .F_Turbo(F_Turbo), .Mem_Size(Mem_Size), .UART_TXD(UART_TXD), .UART_RXD(UART_RXD), .UART_RTS(UART_RTS), .UART_CTS(UART_CTS), .UART_DTR(UART_DTR), .UART_DSR(UART_DSR) ); wire [5:0] cocosound; wire [1:0] turbo_speed = status[20:19]; wire AMW_ACK; wire cpu_speed = status[11]; wire [1:0] mpi = (status[13:12]==2'b00) ? 2'b10: 2'b11; wire video=status[14]; wire cartint=status[16]; wire sg4v6 = status[21]; wire PHASE = status[18]; wire coldboot = status[22]; wire F_Turbo = status[24]; wire [2:0] Mem_Size = status[27:25]; wire digitalJoy = status[23]; reg [2:0] mpi_d = 2'b00; reg first_mpi_chg = 1'b0; reg mpi_reset = 1'b0; always @ (negedge CLK_14) begin mpi_d <= mpi; mpi_reset <= 1'b0; if (~(mpi == mpi_d)) if (~first_mpi_chg) first_mpi_chg <= 1'b1; else mpi_reset <= 1'b1; end reg [2:0] Mem_Size_d = 3'b000; reg first_mem_chg = 1'b0; reg mem_reset = 1'b0; always @ (negedge CLK_14) begin Mem_Size_d <= Mem_Size; mem_reset <= 1'b0; if (~(Mem_Size == Mem_Size_d)) if (~first_mem_chg) first_mem_chg <= 1'b1; else mem_reset <= 1'b1; end // Set bit 9 to swap serial ports... wire [9:0] switch = { 4'b1000,sg4v6,cartint,video,mpi,cpu_speed} ; wire reset = RESET | status[0] | buttons[1]; //wire reset = buttons[1]; wire clk_Q_out; wire [24:0] sdram_cpu_addr; //wire [31:0] sdram_ldout; wire [15:0] sdram_dout; wire [7:0] sdram_cpu_din; wire sdram_cpu_req, sdram_cpu_rnw; wire sdram_cpu_ack, sdram_vid_ack; wire sdram_cpu_ready; wire [24:0] sdram_vid_addr; wire sdram_vid_req; wire sdram_vid_ready; wire sdram_busy; sdram_32r8w coco3_sdram ( .*, .init(reset), .clk(CLK_114), .sdram_cpu_addr(sdram_cpu_addr[24:0]), // .sdram_ldout(sdram_ldout), .sdram_dout(sdram_dout), .sdram_cpu_din(sdram_cpu_din), .sdram_cpu_req(sdram_cpu_req), .sdram_cpu_rnw(sdram_cpu_rnw), .sdram_cpu_ack(sdram_cpu_ack), .sdram_cpu_ready(sdram_cpu_ready), .sdram_vid_addr(sdram_vid_addr[24:0]), .sdram_vid_req(sdram_vid_req), .sdram_vid_ack(sdram_vid_ack), .sdram_vid_ready(sdram_vid_ready), .sdram_busy(sdram_busy) ); wire casdout; wire cas_relay; wire load_tape = ioctl_index == 2; wire [15:0] ram_addr; wire [7:0] ram_data_o; wire ram_rd; wire ram_wr; wire [15:0] ram_ad_buf; always @(posedge clk_sys) begin ram_wr <= ~(ioctl_wr & load_tape); if (ioctl_download) ram_ad_buf <= ioctl_addr[15:0]; else ram_ad_buf <= ram_addr; end COCO_SRAM CC3_CAS1( .CLK(clk_sys), .ADDR(ram_ad_buf), .R_W(ram_wr), .DATA_I(ioctl_data), .DATA_O(ram_data_o) ); cassette cassette( .clk(clk_sys), .Q(clk_Q_out), .rewind(status[15]|~ram_wr), .en(cas_relay), .sdram_addr(ram_addr), .sdram_data(ram_data_o), .sdram_rd(ram_rd), // Not connected for sram .data(casdout) ); endmodule