//////////////////////////////////////////////////////////////////////////////// // Project Name: COCO3 Targeting MISTer // File Name: sdc_top.sv // // CoCo SDC TOP Controller for MISTer // //////////////////////////////////////////////////////////////////////////////// // // // CoCo SDC TOP Controller (sdc_top.sv) by Stan Hodge (stan.pda@gmail.com) // Copyright (c) 2022 by Stan Hodge (stan.pda@gmail.com) // // All rights reserved // Redistribution and use in source and synthezised forms, with or without // modification, are permitted provided that the following conditions are met: // // Redistributions of source code must retain the above copyright notice, // this list of conditions and the following disclaimer. // // Redistributions in synthesized form must reproduce the above copyright // notice, this list of conditions and the following disclaimer in the // documentation and/or other materials provided with the distribution. // // Neither the name of the author nor the names of other contributors may // be used to endorse or promote products derived from this software without // specific prior written permission. // // THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" // AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, // THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR // PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE // LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR // CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF // SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS // INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN // CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) // ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE // POSSIBILITY OF SUCH DAMAGE. // // Please report bugs to the author, but before you do so, please // make sure that this is not a derivative work and that // you have the latest version of this file. // // This is a full FDC controller for 2 floppy drives. It also has a 2 drive // cocosdc imbedded. When booting with a superfloppy, the floppy portion // of this controller will be shutdown and the normal 4 drive fdc will take // over dfc on a different mpi slot. // // Ver 2.00 Implemented with single 1793 ... // //////////////////////////////////////////////////////////////////////////////// //////////////////////////////////////////////////////////////////////////////// module sdc_top( input CLK, // clock input RESET_N, // async reset input [3:0] ADDRESS, // i/o port addr [extended for coco] input CLK_EN, input [7:0] DATA_IN, // data in output [7:0] DATA_HDD, // data out output HALT, // DMA request output NMI_09, // FDC host r/w handling input FF40_CLK, // FDC Write support input FF40_ENA, input SDC_EN_CS, // FDC Read Data support input WD1793_RD, input WD1793_WR_CTRL, // 1793 RD & WR control signal generation input WD1793_RD_CTRL, // SDC I/O input SDC_REG_W_ENA, input SDC_REG_READ, output ext_response, // SD block level interface input [1:0] img_mounted, // signaling that new image has been mounted input img_readonly, // mounted as read only. valid only for active bit in img_mounted input [63:0] img_size, // size of image in bytes. output [31:0] sd_lba[2], output [5:0] sd_blk_cnt[2], // number of blocks-1, total size ((sd_blk_cnt+1)*(1<<(BLKSZ+7))) must be <= 16384! output reg [1:0] sd_rd, output reg [1:0] sd_wr, input [1:0] sd_ack, // SD byte level access. Signals for 2-PORT altsyncram. input [8:0] sd_buff_addr, input [7:0] sd_buff_dout, output [7:0] sd_buff_din[2], input sd_buff_wr ); wire [7:0] DRIVE_SEL_EXT; wire MOTOR; wire WRT_PREC; wire DENSITY; wire HALT_EN; // Diagnostics only //assign probe = {2'd0, HALT_EN_RST, sd_buff_wr, WR[0], RD[0], HALT_EN, HALT}; // Generate a 8.333 Mhz enable for the fdc... and control writes wire ena_8Mhz; wire [5:0] div_8mhz; assign ena_8Mhz = (div_8mhz == 6'd5) ? 1'b1: 1'b0; always@(negedge CLK or negedge RESET_N) begin if (~RESET_N) div_8mhz <= 6'd0; else begin if (ena_8Mhz) div_8mhz <= 6'd0; else div_8mhz <= div_8mhz + 6'd1; end end localparam SDC_MAGIC_CMD = 8'h43; wire sdc_always; wire [7:0] FF40_READ_VALUE = {HALT_EN, DRIVE_SEL_EXT[3], DENSITY, WRT_PREC, MOTOR, DRIVE_SEL_EXT[2:0]}; wire SDC_EN = ((FF40_READ_VALUE == SDC_MAGIC_CMD) | sdc_always); wire [7:0] SDC_READ_DATA; wire FF40_RD = ({SDC_EN_CS, ADDRESS[3:0]} == 5'b10000); //FDC read data path. =$ff40 or wd1793(s) assign DATA_HDD = (FF40_RD) ? FF40_READ_VALUE: (SDC_EN | ext_response) ? SDC_READ_DATA: (SDC_EN_CS & (ADDRESS[3:1] == 3'b001)) ? SDC_READ_DATA: // FF42 & FF43 (WD1793_RD) ? DATA_1793: //(1793[s]) 8'h00; wire [31:0] sdc_sd_lba[2]; wire [31:0] fdc_sd_lba[2]; wire [31:0] wd1793_sd_lba; wire [1:0] sdc_sd_rd; wire wd1793_sd_rd; wire [1:0] fdc_sd_rd; wire [1:0] sdc_sd_wr; wire [1:0] fdc_sd_wr; wire wd1793_sd_wr; wire [7:0] sdc_sd_buff_din[2]; wire [7:0] fdc_sd_buff_din[2]; wire [7:0] wd1793_sd_buff_din; wire wd1793_sd_ack; wire sdc_HALT; assign sd_lba[0:1] = SDC_EN ? sdc_sd_lba[0:1]: fdc_sd_lba[0:1]; assign fdc_sd_lba[0] = wd1793_sd_lba; assign fdc_sd_lba[1] = wd1793_sd_lba; assign sd_rd[1:0] = SDC_EN ? sdc_sd_rd[1:0]: fdc_sd_rd[1:0]; assign fdc_sd_rd[0] = (drive_index == 3'd1) ? wd1793_sd_rd: 1'b0; assign fdc_sd_rd[1] = (drive_index == 3'd2) ? wd1793_sd_rd: 1'b0; assign sd_wr[1:0] = SDC_EN ? sdc_sd_wr[1:0]: fdc_sd_wr[1:0]; assign fdc_sd_wr[0] = (drive_index == 3'd1) ? wd1793_sd_wr: 1'b0; assign fdc_sd_wr[1] = (drive_index == 3'd2) ? wd1793_sd_wr: 1'b0; assign sd_buff_din[0:1] = SDC_EN ? sdc_sd_buff_din[0:1]: fdc_sd_buff_din[0:1]; assign fdc_sd_buff_din[0] = wd1793_sd_buff_din; assign fdc_sd_buff_din[1] = wd1793_sd_buff_din; assign wd1793_sd_ack = (drive_index == 3'd1) ? sd_ack[0]: (drive_index == 3'd2) ? sd_ack[1]: sd_ack[0]; // default is drive 1 sdc coco_sdc( .CLK(CLK), // clock .RESET_N(RESET_N), // async reset .ADDRESS(ADDRESS), // i/o port addr [extended for coco] .SDC_DATA_IN(DATA_IN), // data in .SDC_READ_DATA(SDC_READ_DATA), // data out .SDC_EN(SDC_EN), // SDC is active [input to sdc] .CLK_EN(CLK_EN), .SDC_WR(SDC_REG_W_ENA), .SDC_RD(SDC_REG_READ), .sdc_HALT(sdc_HALT), .ext_response(ext_response), .sdc_always(sdc_always), // SD block level interface .sd_lba(sdc_sd_lba[0:1]), .sd_rd(sdc_sd_rd[1:0]), .sd_wr(sdc_sd_wr[1:0]), .sd_ack(sd_ack[1:0]), // Drive descripters .drive_wp(drive_wp), .drive_ready(drive_ready), .drive_size(drive_size[0:1]), // SD byte level access. Signals for 2-PORT altsyncram. .sd_buff_addr(sd_buff_addr), .sd_buff_dout(sd_buff_dout), .sd_buff_din(sdc_sd_buff_din[0:1]), .sd_buff_wr(sd_buff_wr) ); // $ff40 control register [part 1] wire [3:0] DRIVE_SEL_EXT_PRE = {DATA_IN[6] // Side Select , DATA_IN[2:0]}; // ONLY 2 drives (DS) reg [2:0] drive_index; // SD blk system is a array of 4 systems - one for each drive. // 'drive_index' identifies which controller is addressd. // drive 1-2 for the sdc is denoted as 1 , 2 [0 is no drive selected] always @(negedge FF40_CLK or negedge RESET_N) begin if(!RESET_N) begin DRIVE_SEL_EXT <= 8'h00; MOTOR <= 1'b0; WRT_PREC <= 1'b0; DENSITY <= 1'b0; drive_index <= 3'd0; end else begin if (FF40_ENA) begin DRIVE_SEL_EXT <= {4'b0000, DRIVE_SEL_EXT_PRE}; MOTOR <= DATA_IN[3]; // Turn on motor, not used here just checked, 0=MotorOff 1=MotorOn WRT_PREC <= DATA_IN[4]; // Write Precompensation, not used here DENSITY <= DATA_IN[5]; // Density, not used here just checked case(DRIVE_SEL_EXT_PRE) 4'b0010: drive_index <= 3'd2; 4'b0001: drive_index <= 3'd1; 4'b1010: drive_index <= 3'd2; 4'b1001: drive_index <= 3'd1; 4'b1011: // This is what the Magic Number $43 does so we select a non-active drive drive_index <= 3'd0; 4'b1000: // This is no drive with DS = illegal drive drive_index <= 3'd0; 4'b0000: // This is no drive (maybe 0 in ff40) = illegal drive drive_index <= 3'd0; default: drive_index <= 3'd0; endcase end end end // $ff40 control register [part 2] always @(negedge FF40_CLK or negedge HALT_EN_RST) begin if(!HALT_EN_RST) begin HALT_EN <= 1'b0; end else begin if (FF40_ENA) begin HALT_EN <= DATA_IN[7]; // Normal Halt enable, 0=Disabled 1=Enabled if (sdc_always) HALT_EN <= 1'b0; end end end // Control signals for the wd1793 wire selected_DRQ; wire selected_INTRQ; wire WR; wire RD; wire RD_E; wire HALT_EN_RST; wire [7:0] DATA_1793; reg read; reg write; reg read_d; reg write_d; reg [7:0] DATA_IN_L; reg r_w_active; reg clk_8Mhz_enable_found; reg read1; reg write1; reg [1:0] ADDRESS_L; assign RD = (read || RD_E); // Even with no drive selected allow read to the controller // The idea here is to "stretch" the CPU read and write signals to ensure we catch a 8 mhz enable. // For writes we will buffer the data out to ensure it does not go away. // For reads it is expected that data is available asynchronusly at the cpu rate and the only reason to catch a // 8Mhz edge is to update pointer and misc flags. // This is very nasty code and will likely only work with the present CPU timing. // It is heavily dependant on address and write data being available just after // the previous cycle. wire wd1793_r_w_sync_rst = RESET_N; always @(negedge CLK or negedge wd1793_r_w_sync_rst) begin if(!wd1793_r_w_sync_rst) begin read_d <= 1'b0; write_d <= 1'b0; r_w_active <= 1'b0; clk_8Mhz_enable_found <= 1'b0; WR <= 1'b0; RD_E <= 1'b0; read1 <= 1'b0; write1 <= 1'b0; read <= 1'b0; write <= 1'b0; end else begin // synchronizers read1 <= WD1793_RD_CTRL & ~SDC_EN; read <= read1; write1 <= WD1793_WR_CTRL & ~SDC_EN; write <= write1; // delays for edge detection read_d <= read; write_d <= write; if ((read1 & ~read) | (write1 & ~write)) begin // Latch Address & Data ADDRESS_L <= ADDRESS[1:0]; DATA_IN_L <= DATA_IN; end // Synchronus rising edge of write if ((write == 1'b1) && (write_d == 1'b0)) begin // Set Write r_w_active <= 1'b1; WR <= 1'b1; end // Synchronus rising edge of read if ((read == 1'b1) && (read_d == 1'b0)) begin r_w_active <= 1'b1; RD_E <= 1'b1; end // Clears if (ena_8Mhz && r_w_active) clk_8Mhz_enable_found <= 1'b1; // 1 50Mhz clock later... if (clk_8Mhz_enable_found) begin clk_8Mhz_enable_found <= 1'b0; r_w_active <= 1'b0; WR <= 1'b0; RD_E <= 1'b0; end end end // NMI from disk controller assign NMI_09 = ~SDC_EN & DENSITY & selected_INTRQ; // Send NMI if Double Density (Halt Mode) // HALT from disk controller assign HALT = (~SDC_EN & HALT_EN & ~selected_DRQ) | sdc_HALT; assign HALT_EN_RST = RESET_N & ~selected_INTRQ; // From controller schematic // The SD_BLK interface and thus the wd1793 will allways transfer 1 blk. This is blk qty - 1 per spec. assign sd_blk_cnt[1] = 6'd0; assign sd_blk_cnt[0] = 6'd0; reg drive_wp[2]; reg [1:0] drive_ready = 2'b00; reg [1:0] double_sided = 2'b00; reg [31:0] drive_size[2]; wire [31:0] selected_drive_size; wire selected_drive_ready, selected_drive_wp, selected_double_sided; // As drives are mounted in MISTer this logic saves the write protect and generates ready for // changing drives to the wd1793. // This can also get the disk size to properly handle DS drives - TBD // Reset of drive wp to a default of 1 removed because of persistance. // Drive 0 always @(negedge img_mounted[0]) begin drive_wp[0] <= img_readonly; drive_ready[0] <= 1'b1; drive_size[0] <= img_size[31:0]; //Size / 256 on [31:8] double_sided[0]<= (img_size > 64'd368600) & (img_size < 64'd740000);//20'd368640; end // Drive 1 always @(negedge img_mounted[1]) begin drive_wp[1] <= img_readonly; drive_ready[1] <= 1'b1; drive_size[1] <= img_size[31:0]; //Size / 256 on [31:8] double_sided[1]<= (img_size > 64'd368600) & (img_size < 64'd740000);//20'd368640; end assign selected_drive_size = (drive_index == 3'd1) ? drive_size[0]: (drive_index == 3'd2) ? drive_size[1]: drive_size[0]; // default is drive 1 assign selected_drive_wp = (drive_index == 3'd1) ? drive_wp[0]: (drive_index == 3'd2) ? drive_wp[1]: drive_wp[0]; // default is drive 1 assign selected_double_sided= (drive_index == 3'd1) ? double_sided[0]: (drive_index == 3'd2) ? double_sided[1]: double_sided[0]; // default is drive 1 assign selected_drive_ready = (drive_index == 3'd1) ? drive_ready[0]: (drive_index == 3'd2) ? drive_ready[1]: drive_ready[0]; // default is drive 1 wd1793 #(1,0) coco_wd1793_sdc ( .clk_sys(~CLK), .ce(ena_8Mhz), .reset(~RESET_N), .io_en(1'b1), .rd(RD), .wr(WR), .addr(ADDRESS_L[1:0]), .din(DATA_IN_L), .dout(DATA_1793), .drq(selected_DRQ), .intrq(selected_INTRQ), .img_mounted(1'b0), // Not used when using _override .img_mounted_overide(1'b1), // Load img_size and layout on each clock .img_size(selected_drive_size[19:0]), .sd_lba(wd1793_sd_lba), .sd_rd(wd1793_sd_rd), .sd_wr(wd1793_sd_wr), .sd_ack(wd1793_sd_ack), .sd_buff_addr(sd_buff_addr), .sd_buff_dout(sd_buff_dout), .sd_buff_din(wd1793_sd_buff_din), .sd_buff_wr(sd_buff_wr), .wp(selected_drive_wp), .size_code(3'd5), // 5 is 18 sector x 256 bits COCO standard .layout(~selected_double_sided), // 0 = Track-Side-Sector, 1 - Side-Track-Sector .side(selected_double_sided & DRIVE_SEL_EXT[3]), .ready(selected_drive_ready), .input_active(0), // Section not used .input_addr(0), .input_data(0), .input_wr(0), .buff_din(0) ); endmodule