Changes to fix Rs232 switch and add FijiNet
Fixed Rs-232 Physical/MiSTer Switch Fixed 6551 UART to support 115200 Added slot 1 config and extra ROM [boot2.rom] to support FujiNet. Cleaned up some suttle errors and compatibility with verilator
This commit is contained in:
1 parent
8b8cf72d1f
commit
bbbee96a30
6 files changed
+56
-12
No files matched your search
@@ -308,8 +308,15 @@ end
|
||||
assign TX_CLK = (CTL_REG[3:0] == 4'h0) ? XTAL_CLK_IN:
|
||||
TX_CLK_REG;
|
||||
|
||||
assign RX_CLK = (CTL_REG[4] == 1'b0) ? RX_CLK_IN:
|
||||
TX_CLK;
|
||||
//assign RX_CLK = (CTL_REG[4] == 1'b0) ? RX_CLK_IN:
|
||||
// TX_CLK;
|
||||
|
||||
// Receiver clock. CTL bit 4 = 0 selects the external RxC input, which used to
|
||||
// be the fixed 1.8475 MHz enable (115,200 baud): a program writing CTL=$0F
|
||||
// (19,200, bit 4 clear -- the FujiNet HDB-DOS L3 cart) then transmitted at
|
||||
// 19,200 but received at 115,200. RxC is taken from the baud generator
|
||||
// instead; for CTL[3:0]=0 that is the same 1.8475 MHz clock as before.
|
||||
assign RX_CLK = TX_CLK;
|
||||
|
||||
assign RESET_X = RESET_NX ? 1'b0:
|
||||
RESET_N;
|
||||
|
||||
+25
-3
@@ -328,6 +328,7 @@ wire FLASH_CE_S;
|
||||
|
||||
wire ENA_DSK;
|
||||
wire ENA_DISK2;
|
||||
wire ENA_SLT0;
|
||||
wire ENA_PAK;
|
||||
|
||||
wire HDD_EN;
|
||||
@@ -700,7 +701,7 @@ wire UART_RXD_I;
|
||||
assign UART_TXD = SWITCH[4]? coco_rs232_out:
|
||||
UART_TXD_I;
|
||||
|
||||
assign uart_input = SWITCH[8]? PROBE_I[1]:
|
||||
assign uart_input = ~SWITCH[8]? PROBE_I[1]:
|
||||
UART_RXD;
|
||||
|
||||
|
||||
@@ -801,10 +802,12 @@ assign FLASH_CE_S = ROM_SEL ? 1'b1:
|
||||
ENA_DISK2 ? 1'b1:
|
||||
ENA_PAK ? 1'b1:
|
||||
ENA_DSK ? 1'b1:
|
||||
ENA_SLT0 ? 1'b1:
|
||||
1'b0;
|
||||
|
||||
wire [7:0] COCO3_ROM_DATA;
|
||||
wire [7:0] COCO3_DISK_ROM_DATA;
|
||||
wire [7:0] COCO3_HDB_DISK_ROM_DATA;
|
||||
|
||||
localparam [1:0] BOOT0 = 2'd0;
|
||||
localparam [1:0] BOOT1 = 2'd1;
|
||||
@@ -815,6 +818,7 @@ localparam [5:0] BOOT = 6'd0;
|
||||
|
||||
wire COCO3_ROM_WRITE = (ioctl_index[7:0] == {BOOT0, BOOT}) & ioctl_wr;
|
||||
wire COCO3_DISKROM_WRITE = (ioctl_index[7:0] == {BOOT1, BOOT}) & ioctl_wr;
|
||||
wire COCO3_HDB_DISKROM_WRITE = (ioctl_index[7:0] == {BOOT2, BOOT}) & ioctl_wr;
|
||||
wire COCO3_CART_WRITE = (ioctl_index[5:0] == 6'd1) & ioctl_wr & !cart_lock;
|
||||
|
||||
reg rom_loaded = 1'b0;
|
||||
@@ -826,7 +830,7 @@ begin
|
||||
end
|
||||
|
||||
// A decision.
|
||||
// Looking at this logic it is fairly obvious that the 8Kx8 ROM is not needed.
|
||||
// Looking at this logic it is fairly obvious that the disk 8Kx8 ROM is not needed.
|
||||
// Physically (bus wise) it sits in the same place as the CART rom and is obviously
|
||||
// smaller. I have made these changes at least twice during the development of
|
||||
// this code. While it works and saves the resources of a 8kx8 sram, it does not
|
||||
@@ -857,9 +861,21 @@ COCO_ROM_8K CC3_DISK_ROM(
|
||||
.WRITE(COCO3_DISKROM_WRITE)
|
||||
);
|
||||
|
||||
// DOS Cart for slot 1
|
||||
|
||||
COCO_ROM_8K CC3_HDB_DISK_ROM(
|
||||
.ADDR(FLASH_ADDRESS[12:0]),
|
||||
.DATA(COCO3_HDB_DISK_ROM_DATA),
|
||||
.CLK(~clk_sys),
|
||||
.WR_ADDR(ioctl_addr[12:0]),
|
||||
.WR_DATA(ioctl_data[7:0]),
|
||||
.WRITE(COCO3_HDB_DISKROM_WRITE)
|
||||
);
|
||||
|
||||
|
||||
assign FLASH_DATA = ENA_PAK ? CART_DATA:
|
||||
(ENA_DSK || ENA_DISK2) ? COCO3_DISK_ROM_DATA:
|
||||
ENA_SLT0 ? COCO3_HDB_DISK_ROM_DATA:
|
||||
COCO3_ROM_DATA;
|
||||
|
||||
|
||||
@@ -874,6 +890,9 @@ COCO_ROM_CART CC3_ROM_CART(
|
||||
|
||||
wire SDC_EN_CS;
|
||||
|
||||
assign ENA_SLT0 = ({CART_SEL, MPI_CTS} == 3'b100) ? 1'b1: // Disk C000-DFFF Slot 1
|
||||
1'b0;
|
||||
|
||||
assign ENA_DISK2 = ({CART_SEL, MPI_CTS} == 3'b101) ? 1'b1: // Alternative Disk controller ROM up to 32K
|
||||
1'b0;
|
||||
|
||||
@@ -899,7 +918,10 @@ assign SDC_EN_CS = ({MPI_SCS, ADDRESS[15:5]} == 13'b0111111111010) ? 1'b1:
|
||||
//assign RS232_EN = ({MPI_SCS, ADDRESS[15:2]} == 16'b0011111111011010) ? 1'b1: //FF68-FF6B - Now in slot 1
|
||||
// 1'b0 ;
|
||||
|
||||
assign RS232_EN = ({MPI_SCS[0], ADDRESS[15:2]} == 15'b111111111011010) ? 1'b1: //FF68-FF6B - Now in slot 2 and 4
|
||||
//assign RS232_EN = ({MPI_SCS[0], ADDRESS[15:2]} == 15'b111111111011010) ? 1'b1: //FF68-FF6B - Now in slot 2 and 4
|
||||
// 1'b0;
|
||||
|
||||
assign RS232_EN = (ADDRESS[15:2] == 14'b11111111011010) ? 1'b1: //FF68-FF6B - Now in all slots
|
||||
1'b0;
|
||||
|
||||
assign SLOT3_HW = ({SWITCH[2:1], ADDRESS[15:5]} == 13'b1011111111010) ? 1'b1: // FF40-FF5F Ensure this only appears in slot 3 PHYSICALLY
|
||||
|
||||
@@ -84,6 +84,11 @@ reg [8:0] read_count;
|
||||
reg [4:0] state;
|
||||
reg second_write;
|
||||
reg init_offset_a0;
|
||||
// End-of-line test for the fetch being requested, registered in state_start.
|
||||
// read_count only changes on SDRAM_VID_ACK, so this equals the old in-line
|
||||
// compare; it takes the 9-bit compare off the ACK -> VID_READ_OFFSET path,
|
||||
// which missed timing at 114 MHz.
|
||||
reg last_fetch;
|
||||
reg [4:0] a0_delay;
|
||||
|
||||
localparam state_pre_start = 4'd0;
|
||||
@@ -161,6 +166,7 @@ begin
|
||||
SDRAM_VID_REQ <= 1'b1;
|
||||
state <= state_wait_accept;
|
||||
init_offset_a0 <= PHY_VID_ADD[1];
|
||||
last_fetch <= (read_count >= WORD_END_COUNT);
|
||||
end
|
||||
end
|
||||
|
||||
@@ -170,7 +176,8 @@ begin
|
||||
begin
|
||||
SDRAM_VID_REQ <= 1'b0;
|
||||
|
||||
if (read_count >= WORD_END_COUNT)
|
||||
// if (read_count >= WORD_END_COUNT)
|
||||
if (last_fetch)
|
||||
begin
|
||||
read_count <= 9'h000;
|
||||
state <= state_done;
|
||||
|
||||
+8
-2
@@ -99,6 +99,7 @@ reg [1:0] wd_size_code;
|
||||
wire [7:0] buff_dout;
|
||||
reg [1:0] sd_block = 0;
|
||||
reg format;
|
||||
reg buff_wr;
|
||||
generate
|
||||
if(RWMODE) begin
|
||||
wd1793_dpram sbuf
|
||||
@@ -115,7 +116,6 @@ generate
|
||||
.wren_b(wre & buff_wr & (addr == A_DATA) & ~scan_active),
|
||||
.q_b(buff_dout)
|
||||
);
|
||||
reg buff_wr;
|
||||
end else begin
|
||||
assign buff_dout = 0;
|
||||
assign sd_buff_din = 0;
|
||||
@@ -788,13 +788,19 @@ wire[10:0] edsk_next = ((edsk_addr + 1'd1) >= edsk_size) ? 11'd0 : edsk_addr + 1
|
||||
|
||||
reg [7:0] spt_size = 0;
|
||||
|
||||
// spt_addr is assigned from the always block above, outside the
|
||||
// `generate if(EDSK)` scope it used to be declared in. Quartus tolerates that,
|
||||
// but Verilator rejects it ("Can't find definition of variable: 'spt_addr'"),
|
||||
// so it lives at module scope, next to spt_size. No behavioural change.
|
||||
reg [7:0] spt_addr;
|
||||
|
||||
generate
|
||||
if(EDSK) begin
|
||||
wire [7:0] scan_data = RWMODE ? buff_dout : input_data;
|
||||
reg [53:0] edsk[1992];
|
||||
reg [7:0] spt[166];
|
||||
|
||||
reg [7:0] spt_addr;
|
||||
// reg [7:0] spt_addr;
|
||||
always @(posedge clk_sys) begin
|
||||
{edsk_track,edsk_side,edsk_trackf,edsk_sidef,edsk_sector,edsk_sizecode,edsk_offset} <= edsk[edsk_addr];
|
||||
edsk_spt <= spt[spt_addr];
|
||||
|
||||
Reference in new issue
Block a user