Sim: follow the 20260927 release
- sim.v: the coco3fpga ports changed (RED_O/GREEN_O/BLUE_O, PROBE_O/PROBE_I, Display_Debug) and so did the switch word (rs_swap, UART_INPUT, and the cart interrupt option on SWITCH[9]); mirror CoCo3.sv. SNAC inputs idle high. - rtl/ovo.v: Verilog translation of the new rtl/OVO.vhd overlay; the Makefile drops the removed Mister_Video_GIMEX.v. - PIX_CLK is now a clk_sys enable, high 2 of every 4 cycles, fed to the mixer's ce_pix. Capture video as video_mixer.sv does: on a clk_sys rising edge, one pixel per rising edge of the enable. - New reference screenshots: the release's video timing moves the picture about 2 pixels; text checks unchanged. - Commit tests/dw_boot.sh, which the dw_boot* ignore pattern was hiding. Co-Authored-By: Claude Opus 5.5 (1M context) <[email protected]>
This commit is contained in:
1 parent
50d76dd489
commit
9e70212e87
12 files changed
+184
-19
No files matched your search
+13
-8
@@ -80,7 +80,7 @@ module emu
|
||||
output VGA_VS,
|
||||
output VGA_HB,
|
||||
output VGA_VB,
|
||||
output CE_PIXEL, // = PIX_CLK (CLK_14); sample on its rising edge
|
||||
output CE_PIXEL, // coco3fpga PIX_CLK: a clk_sys enable; sample RGB/syncs on a clk_sys rising edge when high
|
||||
|
||||
output [15:0] AUDIO_L,
|
||||
output [15:0] AUDIO_R,
|
||||
@@ -141,7 +141,8 @@ wire AMW_ACK;
|
||||
|
||||
wire [1:0] mpi = status_q[13:12] + 1'b1;
|
||||
wire CASS_REW_RECORD = status_q[14];
|
||||
wire cartint = status_q[16];
|
||||
wire rs_swap = status_q[16];
|
||||
wire cartint = status_q[19];
|
||||
wire sg4v6 = status_q[21];
|
||||
|
||||
wire PHASE = status_q[18];
|
||||
@@ -151,6 +152,8 @@ wire coldboot = status_q[22];
|
||||
wire F_Turbo = status_q[24];
|
||||
wire [2:0] Mem_Size = status_q[27:25];
|
||||
wire SWAP_M_J = status_q[28];
|
||||
wire display_debug = status_q[29];
|
||||
wire UART_INPUT = status_q[30];
|
||||
|
||||
wire digitalJoy = status_q[23];
|
||||
wire easter_egg = status_q[10];
|
||||
@@ -184,7 +187,7 @@ always @(negedge CLK_14) begin
|
||||
end
|
||||
|
||||
// Set bit 9 to swap serial ports...
|
||||
wire [9:0] switch = { 2'b10,art,sg4v6,cartint,CASS_REW_RECORD,mpi,1'b0};
|
||||
wire [9:0] switch = { cartint,UART_INPUT,art,sg4v6,rs_swap,CASS_REW_RECORD,mpi,1'b0};
|
||||
|
||||
wire reset = RESET | status_q[0] | buttons[1];
|
||||
|
||||
@@ -292,7 +295,7 @@ assign AUDIO_R = audio_right;
|
||||
|
||||
wire [7:0] r, g, b;
|
||||
wire hblank, vblank, hs, vs, pix_clk;
|
||||
wire [31:0] probe;
|
||||
wire [6:0] probe_o;
|
||||
|
||||
wire [71:0] Config_Data = {"SIMULATE", 8'h00};
|
||||
|
||||
@@ -327,9 +330,9 @@ coco3fpga coco3 (
|
||||
|
||||
.COCO_RESET_N((~reset & Programmed_RESET_N)),
|
||||
|
||||
.RED(r),
|
||||
.GREEN(g),
|
||||
.BLUE(b),
|
||||
.RED_O(r),
|
||||
.GREEN_O(g),
|
||||
.BLUE_O(b),
|
||||
|
||||
.EE_N(Programmed_EE),
|
||||
.PHASE(PHASE),
|
||||
@@ -382,7 +385,8 @@ coco3fpga coco3 (
|
||||
|
||||
.GPIO(),
|
||||
|
||||
.PROBE(probe),
|
||||
.PROBE_O(probe_o),
|
||||
.PROBE_I(7'h7F), // SNAC (USER_IN) pins idle high
|
||||
.clk_Q_out(clk_Q_out),
|
||||
.casdout(casdout),
|
||||
.cas_relay(cas_relay),
|
||||
@@ -414,6 +418,7 @@ coco3fpga coco3 (
|
||||
.Mem_Size(Mem_Size),
|
||||
.AUTO_MODE(Auto_Mode),
|
||||
.Config_Data(Config_Data),
|
||||
.Display_Debug(display_debug),
|
||||
|
||||
.UART_TXD(UART_TXD),
|
||||
.UART_RXD(uart_rxd),
|
||||
|
||||
Reference in new issue
Block a user