Add Verilator simulation (ImGui + headless)
verilator/ runs the core on the host with the shared FM-7 / Apple-IIgs sim framework: windowed (ImGui/SDL2) or --headless, typing on a frame schedule, screenshots, text-screen dump, 6809 disassembly trace, floppy/SDC/cart/cassette, and RS-232 Pak serial debugging (TXD decoder, RXD driver, pty bridge, ACIA trace) with a minimal DriveWire server and a script to run the real FujiNet daemon against the sim. See verilator/README.md. - The VHDL the build uses (ROMs, RAMs, font) is converted to Verilog in verilator/rtl/; the VHDL CPU is not instantiated (CoCo3_CYC_ACC_6809). - sdram2.sv is simulated with its own controller logic and an SDR chip model. - run_tests.sh: boot, keyboard, disk, WIDTH 80 and HSCREEN tests, judged on the text screen and byte-for-byte against test-ref/ screenshots. rtl/wd1793.sv: spt_addr and buff_wr are declared at module scope instead of inside generate blocks. They are assigned outside those blocks; Quartus accepted it, Verilator rejected spt_addr and silently split buff_wr into a separate net. No change on the FPGA (FM-7 made the same fix). Co-Authored-By: Claude Opus 5.5 (1M context) <[email protected]>
This commit is contained in:
1 parent
aae1ceabf1
commit
874f4f3083
79 files changed
+81058
-2
No files matched your search
@@ -0,0 +1,81 @@
|
||||
#pragma once
|
||||
//============================================================================
|
||||
// RS-232 Pak (glb6551) line model for the CoCo3 sim.
|
||||
//
|
||||
// Works on the pins, not on the registers: TXD is decoded as the far end of
|
||||
// the cable would see it, and RXD is driven bit by bit. So a byte is only
|
||||
// logged as transmitted if the 6551 really shifted it out, at the baud rate
|
||||
// it was really programmed for.
|
||||
//
|
||||
// Clocked once per clk_sys (57.272727 MHz). Bit timing follows
|
||||
// rtl/UART_6551/uart_6551.v: a 1.8475 MHz enable (clk_sys / 31) feeds the
|
||||
// divider; the 6551 samples at 16x the bit rate.
|
||||
//
|
||||
// Optional pty bridge: the slave side (/dev/ttysNNN) can be opened by a
|
||||
// DriveWire server or FujiNet-PC, or by socat to reach a TCP one. Note the sim
|
||||
// runs ~50x slower than real time, so the far end sees ~400 baud of real
|
||||
// throughput whatever the programmed rate is.
|
||||
//============================================================================
|
||||
|
||||
#include <cstdint>
|
||||
#include <cstdio>
|
||||
#include <deque>
|
||||
#include <string>
|
||||
#include <vector>
|
||||
|
||||
struct SerialPort {
|
||||
// --- configuration -------------------------------------------------
|
||||
bool print_bytes = true; // SERIAL TX/RX lines on stdout
|
||||
FILE* log_file = nullptr; // --serial-log: one line per byte
|
||||
// Rate the far end sends at, in clk_sys cycles per bit. 0 = the rate the
|
||||
// 6551 transmits at, i.e. a peer configured to match. RXD is driven at this
|
||||
// rate whatever the 6551's RECEIVER is clocked at, so a receiver-clock
|
||||
// mismatch shows up as garbage, as it would on the cable.
|
||||
long line_bit_clks = 0;
|
||||
long line_clks() const { return line_bit_clks ? line_bit_clks : bit_clks(ctl); }
|
||||
|
||||
// --- state visible to the UI ----------------------------------------
|
||||
std::string pty_name;
|
||||
long tx_count = 0, rx_count = 0;
|
||||
long tx_framing_errors = 0;
|
||||
std::vector<uint8_t> tx_hist, rx_hist; // capped, for the Serial window
|
||||
uint8_t ctl = 0, cmd = 0; // last seen 6551 registers
|
||||
|
||||
// Bits per word and clk_sys cycles per bit for a control/command value.
|
||||
static int data_bits(uint8_t ctl) { return 8 - ((ctl >> 5) & 3); }
|
||||
static long bit_clks(uint8_t ctl); // transmitter / internal generator
|
||||
static long rx_bit_clks(uint8_t ctl); // receiver (CTL bit 4 picks the source)
|
||||
static double baud(long clks);
|
||||
|
||||
bool open_pty();
|
||||
void queue_rx(const uint8_t* p, size_t n);
|
||||
|
||||
// One clk_sys cycle. Returns the level to drive on RXD.
|
||||
uint8_t clock(uint8_t txd, uint8_t ctl, uint8_t cmd, int frame);
|
||||
|
||||
// Flush the per-frame byte lines.
|
||||
void end_frame(int frame);
|
||||
|
||||
private:
|
||||
// TX decoder
|
||||
int tx_phase = 0; // 0 idle, 1 start, 2 data, 3 parity, 4 stop
|
||||
long tx_timer = 0;
|
||||
int tx_bitn = 0;
|
||||
uint16_t tx_shift = 0;
|
||||
uint8_t tx_last = 1;
|
||||
// RX driver
|
||||
std::deque<uint8_t> rx_queue;
|
||||
uint16_t rx_frame = 0; // bits to send, LSB first
|
||||
int rx_bits_left = 0;
|
||||
long rx_timer = 0;
|
||||
uint8_t rx_level = 1;
|
||||
// pty
|
||||
int pty_fd = -1, pty_slave_fd = -1;
|
||||
long poll_timer = 0;
|
||||
// per-frame print buffers
|
||||
std::vector<uint8_t> tx_line, rx_line;
|
||||
|
||||
void got_tx_byte(uint8_t b, bool framing_ok, int frame);
|
||||
void poll_pty();
|
||||
void print_line(const char* dir, std::vector<uint8_t>& v, int frame);
|
||||
};
|
||||
Reference in new issue
Block a user