FujiNet Update.
Added slot1 transmit of $FF upon Cold Boot to Fujinet daemon. Fixed set / clear of CoCo3 SAM registers to work with both reads and writes.
This commit is contained in:
1 parent
bbbee96a30
commit
5e1b2e4c33
4 files changed
+387
-29
No files matched your search
+22
-4
@@ -6,12 +6,30 @@
|
|||||||
[done]
|
[done]
|
||||||
4. Routing RS-232 tx/rx lines to the SNAC port for initial serial debugging
|
4. Routing RS-232 tx/rx lines to the SNAC port for initial serial debugging
|
||||||
of Fuji-Net interface. [done - untested]
|
of Fuji-Net interface. [done - untested]
|
||||||
|
5. Added Fujinet support.
|
||||||
|
a) Install Fujinet [seperate instruction document]
|
||||||
|
a) Slot 1 is now Fujunet only support.
|
||||||
|
b) You will need HDBDos 'HDBDW3S3' which will be autoloaded if named
|
||||||
|
BOOT2.ROM. Tested with ver 1.5 SY6551 @ 115,200 baud.
|
||||||
|
c) In the Debug menu on the OSD 'Swap Mister Uart:' is set to RS CART.
|
||||||
|
'SWAP Uart to IO:' is set to 'Off'.
|
||||||
|
d) In the 'System' page of the OSD, 'Uart Mode' Should be set to 'Fujinet'
|
||||||
|
and the baud rate to '115,200'.
|
||||||
|
e) In slot 1 ONLY [Fujinet], a cold boot issued through the OSD will cause
|
||||||
|
a firewire reset command [$FF] to be transmitted to the Fujinet daemon
|
||||||
|
which will cause the Fujinet Config screem to come up after boot.
|
||||||
|
f) The SD drive in Fujinet is configured to the CoCo3 games area on the MiSTer
|
||||||
|
storage location.
|
||||||
|
6. A bug was fixed in that this core did not allow SAM registers to be set / cleared
|
||||||
|
by reads. This was fixed with the side effect of preventing older OS9 disks
|
||||||
|
from booting. [OS9 L1v1.02]. In the OSD Debug Menu, 'SAM Wrt Only Ena' should
|
||||||
|
be set to 'Off' for true CoCo3 compadibility. Turn it on if your old OS9
|
||||||
|
disks hang.
|
||||||
|
a) This fix has moved the RTC availibility to be moved to the config data.
|
||||||
|
(see manual for details)
|
||||||
|
|
||||||
To Do...
|
To Do...
|
||||||
1. Add Fuji-Net port.
|
1. Fix Castle of Tharoggad
|
||||||
2. Add Speech / Music cart
|
|
||||||
3. Fix Castle of Tharoggad
|
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
|
|||||||
@@ -36,4 +36,5 @@ set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_32K.vhd
|
|||||||
set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_8K.vhd
|
set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_8K.vhd
|
||||||
set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_16.vhd
|
set_global_assignment -name VHDL_FILE rtl/rom/coco_rom_16.vhd
|
||||||
set_global_assignment -name VHDL_FILE rtl/OVO.vhd
|
set_global_assignment -name VHDL_FILE rtl/OVO.vhd
|
||||||
|
set_global_assignment -name VERILOG_FILE rtl/UIM.v
|
||||||
set_global_assignment -name SDC_FILE rtl/CoCo3FPGA.sdc
|
set_global_assignment -name SDC_FILE rtl/CoCo3FPGA.sdc
|
||||||
@@ -0,0 +1,196 @@
|
|||||||
|
////////////////////////////////////////////////////////////////////////////////
|
||||||
|
// Project Name: CoCo3FPGA Version 5.0
|
||||||
|
// File Name: UIM.v
|
||||||
|
//
|
||||||
|
// CoCo3 in an FPGA
|
||||||
|
//
|
||||||
|
////////////////////////////////////////////////////////////////////////////////
|
||||||
|
//
|
||||||
|
////////////////////////////////////////////////////////////////////////////////
|
||||||
|
//
|
||||||
|
// Color Computer 3 compatible system on a chip
|
||||||
|
//
|
||||||
|
//
|
||||||
|
// Copyright (c) 2008 Gary Becker ([email protected])
|
||||||
|
//
|
||||||
|
// All rights reserved
|
||||||
|
//
|
||||||
|
// Redistribution and use in source and synthezised forms, with or without
|
||||||
|
// modification, are permitted provided that the following conditions are met:
|
||||||
|
//
|
||||||
|
// Redistributions of source code must retain the above copyright notice,
|
||||||
|
// this list of conditions and the following disclaimer.
|
||||||
|
//
|
||||||
|
// Redistributions in synthesized form must reproduce the above copyright
|
||||||
|
// notice, this list of conditions and the following disclaimer in the
|
||||||
|
// documentation and/or other materials provided with the distribution.
|
||||||
|
//
|
||||||
|
// Neither the name of the author nor the names of other contributors may
|
||||||
|
// be used to endorse or promote products derived from this software without
|
||||||
|
// specific prior written permission.
|
||||||
|
//
|
||||||
|
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
||||||
|
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
|
||||||
|
// THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
|
||||||
|
// PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE
|
||||||
|
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
|
||||||
|
// CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
|
||||||
|
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
|
||||||
|
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
|
||||||
|
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
||||||
|
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||||
|
// POSSIBILITY OF SUCH DAMAGE.
|
||||||
|
//
|
||||||
|
// Please report bugs to the author, but before you do so, please
|
||||||
|
// make sure that this is not a derivative work and that
|
||||||
|
// you have the latest version of this file.
|
||||||
|
//
|
||||||
|
//
|
||||||
|
////////////////////////////////////////////////////////////////////////////////
|
||||||
|
// Stan Hodge
|
||||||
|
//
|
||||||
|
// UART Injection Module by Stan Hodge 11/8/26
|
||||||
|
//
|
||||||
|
// This module uses the AMW_END chain to cause a $FF to be written to the 6551
|
||||||
|
// uart, then delay until that transmission has been made, then pass on the AMW_END.
|
||||||
|
// This only occurs in slot 1. In other slots, AMW_END_OUT = AMW_END_IN.
|
||||||
|
//
|
||||||
|
////////////////////////////////////////////////////////////////////////////////
|
||||||
|
|
||||||
|
|
||||||
|
module UIM(
|
||||||
|
input CLK,
|
||||||
|
input RESET_N,
|
||||||
|
|
||||||
|
input [1:0] MPI_SCS,
|
||||||
|
input PH_2,
|
||||||
|
|
||||||
|
input AMW_END_IN,
|
||||||
|
input ENABLE_IN,
|
||||||
|
input RW_N_IN,
|
||||||
|
|
||||||
|
input [1:0] ADDRESS_IN,
|
||||||
|
input [7:0] DATA_IN,
|
||||||
|
|
||||||
|
|
||||||
|
output AMW_END_OUT,
|
||||||
|
output ENABLE_OUT,
|
||||||
|
output RW_N_OUT,
|
||||||
|
|
||||||
|
output [1:0] ADDRESS_OUT,
|
||||||
|
output [7:0] DATA_OUT
|
||||||
|
|
||||||
|
);
|
||||||
|
|
||||||
|
////////////////////////////////////////////////////////////
|
||||||
|
|
||||||
|
|
||||||
|
localparam UIM_START = 3'd0;
|
||||||
|
localparam UIM_F1 = 3'd1;
|
||||||
|
localparam UIM_F2 = 3'd2;
|
||||||
|
localparam UIM_F3 = 3'd3;
|
||||||
|
localparam UIM_F4 = 3'd4;
|
||||||
|
localparam UIM_F5 = 3'd5;
|
||||||
|
localparam UIM_F6 = 3'd6;
|
||||||
|
localparam UIM_ST_END = 3'd7;
|
||||||
|
|
||||||
|
reg [2:0] state;
|
||||||
|
reg mux,rw,ena,timer_ena, AMW_END_OUT_ST;
|
||||||
|
reg [13:0] timer;
|
||||||
|
|
||||||
|
assign ADDRESS_OUT = (mux == 1'b0) ? ADDRESS_IN:
|
||||||
|
2'b00;
|
||||||
|
|
||||||
|
assign DATA_OUT = (mux == 1'b0) ? DATA_IN:
|
||||||
|
8'b11111111;
|
||||||
|
|
||||||
|
assign RW_N_OUT = (mux == 1'b0) ? RW_N_IN:
|
||||||
|
rw;
|
||||||
|
|
||||||
|
assign ENABLE_OUT = (mux == 1'b0) ? ENABLE_IN:
|
||||||
|
ena;
|
||||||
|
|
||||||
|
assign AMW_END_OUT = (MPI_SCS == 2'b00) ? AMW_END_OUT_ST:
|
||||||
|
AMW_END_IN;
|
||||||
|
|
||||||
|
always @(negedge CLK or negedge RESET_N)
|
||||||
|
begin
|
||||||
|
if(!RESET_N)
|
||||||
|
begin
|
||||||
|
state <= UIM_START;
|
||||||
|
mux <= 1'b0;
|
||||||
|
rw <= 1'b1;
|
||||||
|
ena <= 1'b0;
|
||||||
|
timer <= 14'b00000000000000;
|
||||||
|
timer_ena <=1'b0;
|
||||||
|
AMW_END_OUT_ST <= 1'b0;
|
||||||
|
end
|
||||||
|
else
|
||||||
|
begin
|
||||||
|
|
||||||
|
if (timer_ena == 1'b1)
|
||||||
|
timer <= timer + 1'b1;
|
||||||
|
|
||||||
|
case(state)
|
||||||
|
|
||||||
|
UIM_START:
|
||||||
|
begin
|
||||||
|
if ((MPI_SCS == 2'b00) && (AMW_END_IN == 1'b1))
|
||||||
|
state <= UIM_F1;
|
||||||
|
end
|
||||||
|
|
||||||
|
UIM_F1:
|
||||||
|
begin
|
||||||
|
mux <= 1'b1;
|
||||||
|
state <= UIM_F2;
|
||||||
|
end
|
||||||
|
|
||||||
|
UIM_F2:
|
||||||
|
begin
|
||||||
|
ena <= 1'b1;
|
||||||
|
state <= UIM_F3;
|
||||||
|
end
|
||||||
|
|
||||||
|
UIM_F3:
|
||||||
|
begin
|
||||||
|
rw <= 1'b0;
|
||||||
|
state <= UIM_F4;
|
||||||
|
end
|
||||||
|
|
||||||
|
UIM_F4:
|
||||||
|
begin
|
||||||
|
if (PH_2)
|
||||||
|
begin
|
||||||
|
rw <= 1'b1;
|
||||||
|
state <= UIM_F5;
|
||||||
|
end
|
||||||
|
end
|
||||||
|
|
||||||
|
UIM_F5:
|
||||||
|
begin
|
||||||
|
ena <= 1'b0;
|
||||||
|
state <= UIM_F6;
|
||||||
|
end
|
||||||
|
|
||||||
|
UIM_F6:
|
||||||
|
begin
|
||||||
|
mux <= 1'b0;
|
||||||
|
timer_ena <= 1'b1;
|
||||||
|
state <= UIM_ST_END;
|
||||||
|
end
|
||||||
|
|
||||||
|
UIM_ST_END:
|
||||||
|
begin
|
||||||
|
if (timer[13] == 1'b1)
|
||||||
|
begin
|
||||||
|
AMW_END_OUT_ST <= 1'b1;
|
||||||
|
timer_ena <= 1'b0;
|
||||||
|
end
|
||||||
|
end
|
||||||
|
|
||||||
|
default:;
|
||||||
|
endcase
|
||||||
|
end
|
||||||
|
end
|
||||||
|
|
||||||
|
endmodule
|
||||||
+168
-25
@@ -106,7 +106,7 @@ input ps2_data,
|
|||||||
|
|
||||||
input [24:0] ps2_mouse,
|
input [24:0] ps2_mouse,
|
||||||
|
|
||||||
input Display_Debug,
|
input SAM_WO,
|
||||||
|
|
||||||
// RS-232
|
// RS-232
|
||||||
output UART_TXD,
|
output UART_TXD,
|
||||||
@@ -698,6 +698,7 @@ assign BUTTON_N[3:0] = {COCO_RESET_N, 2'b1,EE_N};
|
|||||||
wire UART_TXD_I;
|
wire UART_TXD_I;
|
||||||
wire UART_RXD_I;
|
wire UART_RXD_I;
|
||||||
|
|
||||||
|
|
||||||
assign UART_TXD = SWITCH[4]? coco_rs232_out:
|
assign UART_TXD = SWITCH[4]? coco_rs232_out:
|
||||||
UART_TXD_I;
|
UART_TXD_I;
|
||||||
|
|
||||||
@@ -1024,7 +1025,7 @@ always @(negedge clk_sys or negedge RESET_N)
|
|||||||
begin
|
begin
|
||||||
if(!RESET_N)
|
if(!RESET_N)
|
||||||
begin
|
begin
|
||||||
Build_Info_Count <= 4'b0000;
|
Build_Info_Count <= 5'b00000;
|
||||||
Build_Info <= 8'h00;
|
Build_Info <= 8'h00;
|
||||||
Build_Info_Read <= 1'b0;
|
Build_Info_Read <= 1'b0;
|
||||||
Build_Info_Read_Delay <= 1'b0;
|
Build_Info_Read_Delay <= 1'b0;
|
||||||
@@ -1070,6 +1071,25 @@ begin
|
|||||||
4'd13:
|
4'd13:
|
||||||
Build_Info <= (Version_Lo + BOARD_TYPE);
|
Build_Info <= (Version_Lo + BOARD_TYPE);
|
||||||
|
|
||||||
|
// RTC Moved here so not to collide with SAM reads
|
||||||
|
|
||||||
|
4'd14:
|
||||||
|
Build_Info <= {3'b000, CENT};
|
||||||
|
4'd15:
|
||||||
|
Build_Info <= {1'b0, YEAR};
|
||||||
|
4'd16:
|
||||||
|
Build_Info <= {4'b0000, MNTH};
|
||||||
|
4'd17:
|
||||||
|
Build_Info <= {3'b000, DMTH};
|
||||||
|
4'd18:
|
||||||
|
Build_Info <= {5'b00000, DWK};
|
||||||
|
4'd19:
|
||||||
|
Build_Info <= {3'b000, HOUR};
|
||||||
|
4'd20:
|
||||||
|
Build_Info <= {2'b00, MIN};
|
||||||
|
4'd21:
|
||||||
|
Build_Info <= {2'b00, SEC};
|
||||||
|
|
||||||
default:
|
default:
|
||||||
Build_Info <= 8'h00;
|
Build_Info <= 8'h00;
|
||||||
endcase
|
endcase
|
||||||
@@ -1171,16 +1191,6 @@ assign DATA_IN =
|
|||||||
(ADDRESS == 16'hFFBD) ? {2'b00, PALETTE[13][5:0]}:
|
(ADDRESS == 16'hFFBD) ? {2'b00, PALETTE[13][5:0]}:
|
||||||
(ADDRESS == 16'hFFBE) ? {2'b00, PALETTE[14][5:0]}:
|
(ADDRESS == 16'hFFBE) ? {2'b00, PALETTE[14][5:0]}:
|
||||||
(ADDRESS == 16'hFFBF) ? {2'b00, PALETTE[15][5:0]}:
|
(ADDRESS == 16'hFFBF) ? {2'b00, PALETTE[15][5:0]}:
|
||||||
(ADDRESS == 16'hFFC0) ? {3'b000, CENT}:
|
|
||||||
(ADDRESS == 16'hFFC1) ? {1'b0, YEAR}:
|
|
||||||
(ADDRESS == 16'hFFC2) ? {4'h0, MNTH}:
|
|
||||||
(ADDRESS == 16'hFFC3) ? {3'b000, DMTH}:
|
|
||||||
(ADDRESS == 16'hFFC4) ? {5'b00000, DWK}:
|
|
||||||
(ADDRESS == 16'hFFC5) ? {3'b000, HOUR}:
|
|
||||||
(ADDRESS == 16'hFFC6) ? {2'b00, MIN}:
|
|
||||||
(ADDRESS == 16'hFFC7) ? {2'b00, SEC}:
|
|
||||||
|
|
||||||
(ADDRESS == 16'hFFD9) ? {5'h00, RATE_PGM}:
|
|
||||||
|
|
||||||
(ADDRESS == 16'hFFEF) ? Build_Info:
|
(ADDRESS == 16'hFFEF) ? Build_Info:
|
||||||
8'hAA;
|
8'hAA;
|
||||||
@@ -1225,7 +1235,7 @@ wire AMW_EN;
|
|||||||
wire AMW_Ready;
|
wire AMW_Ready;
|
||||||
wire AMW_End;
|
wire AMW_End;
|
||||||
|
|
||||||
assign AMW_ACK = AMW_End;
|
//assign AMW_ACK = AMW_End;
|
||||||
|
|
||||||
AMW coco_AMW (
|
AMW coco_AMW (
|
||||||
.CLK(clk_sys),
|
.CLK(clk_sys),
|
||||||
@@ -3553,19 +3563,125 @@ begin
|
|||||||
end
|
end
|
||||||
else
|
else
|
||||||
begin
|
begin
|
||||||
if(ADDRESS == 16'hFFE8)
|
// Register reads
|
||||||
|
if (~SAM_WO)
|
||||||
|
begin
|
||||||
|
case (ADDRESS)
|
||||||
|
16'hFFC0:
|
||||||
|
begin
|
||||||
|
V[0] <= 1'b0;
|
||||||
|
end
|
||||||
|
16'hFFC1:
|
||||||
|
begin
|
||||||
|
V[0] <= 1'b1;
|
||||||
|
end
|
||||||
|
16'hFFC2:
|
||||||
|
begin
|
||||||
|
V[1] <= 1'b0;
|
||||||
|
end
|
||||||
|
16'hFFC3:
|
||||||
|
begin
|
||||||
|
V[1] <= 1'b1;
|
||||||
|
end
|
||||||
|
16'hFFC4:
|
||||||
|
begin
|
||||||
|
V[2] <= 1'b0;
|
||||||
|
end
|
||||||
|
16'hFFC5:
|
||||||
|
begin
|
||||||
|
V[2] <= 1'b1;
|
||||||
|
end
|
||||||
|
16'hFFC6:
|
||||||
|
begin
|
||||||
|
VERT[0] <= 1'b0;
|
||||||
|
end
|
||||||
|
16'hFFC7:
|
||||||
|
begin
|
||||||
|
VERT[0] <= 1'b1;
|
||||||
|
end
|
||||||
|
16'hFFC8:
|
||||||
|
begin
|
||||||
|
VERT[1] <= 1'b0;
|
||||||
|
end
|
||||||
|
16'hFFC9:
|
||||||
|
begin
|
||||||
|
VERT[1] <= 1'b1;
|
||||||
|
end
|
||||||
|
16'hFFCA:
|
||||||
|
begin
|
||||||
|
VERT[2] <= 1'b0;
|
||||||
|
end
|
||||||
|
16'hFFCB:
|
||||||
|
begin
|
||||||
|
VERT[2] <= 1'b1;
|
||||||
|
end
|
||||||
|
16'hFFCC:
|
||||||
|
begin
|
||||||
|
VERT[3] <= 1'b0;
|
||||||
|
end
|
||||||
|
16'hFFCD:
|
||||||
|
begin
|
||||||
|
VERT[3] <= 1'b1;
|
||||||
|
end
|
||||||
|
16'hFFCE:
|
||||||
|
begin
|
||||||
|
VERT[4] <= 1'b0;
|
||||||
|
end
|
||||||
|
16'hFFCF:
|
||||||
|
begin
|
||||||
|
VERT[4] <= 1'b1;
|
||||||
|
end
|
||||||
|
16'hFFD0:
|
||||||
|
begin
|
||||||
|
VERT[5] <= 1'b0;
|
||||||
|
end
|
||||||
|
16'hFFD1:
|
||||||
|
begin
|
||||||
|
VERT[5] <= 1'b1;
|
||||||
|
end
|
||||||
|
16'hFFD2:
|
||||||
|
begin
|
||||||
|
VERT[6] <= 1'b0;
|
||||||
|
end
|
||||||
|
16'hFFD3:
|
||||||
|
begin
|
||||||
|
VERT[6] <= 1'b1;
|
||||||
|
end
|
||||||
|
16'hFFD8:
|
||||||
|
begin
|
||||||
|
RATE <= 1'b0;
|
||||||
|
RATE_PGM <= 3'b010;
|
||||||
|
end
|
||||||
|
16'hFFD9:
|
||||||
|
begin
|
||||||
|
RATE <= 1'b1;
|
||||||
|
RATE_PGM <= 3'b010; // Normal Turbo
|
||||||
|
end
|
||||||
|
16'hFFDE:
|
||||||
|
begin
|
||||||
|
RAM <= 1'b0;
|
||||||
|
end
|
||||||
|
16'hFFDF:
|
||||||
|
begin
|
||||||
|
RAM <= 1'b1;
|
||||||
|
end
|
||||||
|
endcase
|
||||||
|
end
|
||||||
|
|
||||||
|
case (ADDRESS)
|
||||||
|
|
||||||
|
16'hFFE8:
|
||||||
begin
|
begin
|
||||||
if(GART_INC[1])
|
if(GART_INC[1])
|
||||||
GART_READ <= GART_READ + 1'b1;
|
GART_READ <= GART_READ + 1'b1;
|
||||||
end
|
end
|
||||||
else
|
|
||||||
|
16'hFFE9:
|
||||||
begin
|
begin
|
||||||
if(ADDRESS == 16'hFFE9)
|
if(GART_INC[1])
|
||||||
begin
|
GART_READ <= GART_READ + 1'b1;
|
||||||
if(GART_INC[1])
|
|
||||||
GART_READ <= GART_READ + 1'b1;
|
|
||||||
end
|
|
||||||
end
|
end
|
||||||
|
endcase
|
||||||
end
|
end
|
||||||
end
|
end
|
||||||
end
|
end
|
||||||
@@ -4240,6 +4356,33 @@ begin
|
|||||||
end
|
end
|
||||||
|
|
||||||
|
|
||||||
|
UIM UIM_COCO3(
|
||||||
|
.CLK(clk_sys),
|
||||||
|
.RESET_N(RESET_N),
|
||||||
|
|
||||||
|
.MPI_SCS(MPI_SCS),
|
||||||
|
.PH_2(PH_2),
|
||||||
|
|
||||||
|
.AMW_END_IN(AMW_End),
|
||||||
|
.ENABLE_IN(RS232_EN),
|
||||||
|
.RW_N_IN(RW_N),
|
||||||
|
|
||||||
|
.ADDRESS_IN(ADDRESS[1:0]),
|
||||||
|
.DATA_IN(DATA_OUT),
|
||||||
|
|
||||||
|
.AMW_END_OUT(AMW_ACK),
|
||||||
|
.ENABLE_OUT(RS232_EN_ST),
|
||||||
|
.RW_N_OUT(RW_N_ST),
|
||||||
|
|
||||||
|
.ADDRESS_OUT(ADDRESS_ST),
|
||||||
|
.DATA_OUT(DATA_OUT_ST)
|
||||||
|
);
|
||||||
|
|
||||||
|
wire RS232_EN_ST;
|
||||||
|
wire RW_N_ST;
|
||||||
|
wire [1:0] ADDRESS_ST;
|
||||||
|
wire [7:0] DATA_OUT_ST;
|
||||||
|
|
||||||
// RS232PAK UART
|
// RS232PAK UART
|
||||||
glb6551 RS232(
|
glb6551 RS232(
|
||||||
.RESET_N(RESET_N),
|
.RESET_N(RESET_N),
|
||||||
@@ -4248,12 +4391,12 @@ glb6551 RS232(
|
|||||||
.RX_CLK_IN(CLK_6551_EN), // These are now enables
|
.RX_CLK_IN(CLK_6551_EN), // These are now enables
|
||||||
.XTAL_CLK_IN(CLK_6551_EN),
|
.XTAL_CLK_IN(CLK_6551_EN),
|
||||||
.PH_2(PH_2),
|
.PH_2(PH_2),
|
||||||
.DI(DATA_OUT),
|
.DI(DATA_OUT_ST),
|
||||||
.DO(DATA_RS232),
|
.DO(DATA_RS232),
|
||||||
.IRQ(SER_IRQ),
|
.IRQ(SER_IRQ),
|
||||||
.CS({1'b0, RS232_EN}),
|
.CS({1'b0, RS232_EN_ST}),
|
||||||
.RW_N(RW_N),
|
.RW_N(RW_N_ST),
|
||||||
.RS(ADDRESS[1:0]),
|
.RS(ADDRESS_ST[1:0]),
|
||||||
.TXDATA_OUT(UART_TXD_I),
|
.TXDATA_OUT(UART_TXD_I),
|
||||||
.RXDATA_IN(UART_RXD_I),
|
.RXDATA_IN(UART_RXD_I),
|
||||||
.RTS(UART_RTS),
|
.RTS(UART_RTS),
|
||||||
@@ -4320,7 +4463,7 @@ ovo #(.COLS(32), .LINES(23)) NOROMOVO
|
|||||||
.i_Hcount({1'b0, PIXEL_COUNT[10:1]}),
|
.i_Hcount({1'b0, PIXEL_COUNT[10:1]}),
|
||||||
.i_VCount(LINE),
|
.i_VCount(LINE),
|
||||||
.o_r(CN_R),
|
.o_r(CN_R),
|
||||||
.ena(Display_Debug || ((!rom_loaded) && SEC[0])),
|
.ena((!rom_loaded) && SEC[0]),
|
||||||
.in0(NOrom1),
|
.in0(NOrom1),
|
||||||
.in1(NOrom2)
|
.in1(NOrom2)
|
||||||
);
|
);
|
||||||
|
|||||||
Reference in new issue
Block a user