FujiNet Update.

Added slot1 transmit of $FF upon Cold Boot to Fujinet daemon.  Fixed set / clear of CoCo3 SAM registers to work with both reads and writes.
This commit is contained in:
shodge12 committed 2026-11-10 20:22:47 -05:00
1 parent bbbee96a30
commit 5e1b2e4c33
4 files changed
+387 -29

No files matched your search

+196
View File
@@ -0,0 +1,196 @@
////////////////////////////////////////////////////////////////////////////////
// Project Name: CoCo3FPGA Version 5.0
// File Name: UIM.v
//
// CoCo3 in an FPGA
//
////////////////////////////////////////////////////////////////////////////////
//
////////////////////////////////////////////////////////////////////////////////
//
// Color Computer 3 compatible system on a chip
//
//
// Copyright (c) 2008 Gary Becker ([email protected])
//
// All rights reserved
//
// Redistribution and use in source and synthezised forms, with or without
// modification, are permitted provided that the following conditions are met:
//
// Redistributions of source code must retain the above copyright notice,
// this list of conditions and the following disclaimer.
//
// Redistributions in synthesized form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the distribution.
//
// Neither the name of the author nor the names of other contributors may
// be used to endorse or promote products derived from this software without
// specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
// THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
// PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
// CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
// POSSIBILITY OF SUCH DAMAGE.
//
// Please report bugs to the author, but before you do so, please
// make sure that this is not a derivative work and that
// you have the latest version of this file.
//
//
////////////////////////////////////////////////////////////////////////////////
// Stan Hodge
//
// UART Injection Module by Stan Hodge 11/8/26
//
// This module uses the AMW_END chain to cause a $FF to be written to the 6551
// uart, then delay until that transmission has been made, then pass on the AMW_END.
// This only occurs in slot 1. In other slots, AMW_END_OUT = AMW_END_IN.
//
////////////////////////////////////////////////////////////////////////////////
module UIM(
input CLK,
input RESET_N,
input [1:0] MPI_SCS,
input PH_2,
input AMW_END_IN,
input ENABLE_IN,
input RW_N_IN,
input [1:0] ADDRESS_IN,
input [7:0] DATA_IN,
output AMW_END_OUT,
output ENABLE_OUT,
output RW_N_OUT,
output [1:0] ADDRESS_OUT,
output [7:0] DATA_OUT
);
////////////////////////////////////////////////////////////
localparam UIM_START = 3'd0;
localparam UIM_F1 = 3'd1;
localparam UIM_F2 = 3'd2;
localparam UIM_F3 = 3'd3;
localparam UIM_F4 = 3'd4;
localparam UIM_F5 = 3'd5;
localparam UIM_F6 = 3'd6;
localparam UIM_ST_END = 3'd7;
reg [2:0] state;
reg mux,rw,ena,timer_ena, AMW_END_OUT_ST;
reg [13:0] timer;
assign ADDRESS_OUT = (mux == 1'b0) ? ADDRESS_IN:
2'b00;
assign DATA_OUT = (mux == 1'b0) ? DATA_IN:
8'b11111111;
assign RW_N_OUT = (mux == 1'b0) ? RW_N_IN:
rw;
assign ENABLE_OUT = (mux == 1'b0) ? ENABLE_IN:
ena;
assign AMW_END_OUT = (MPI_SCS == 2'b00) ? AMW_END_OUT_ST:
AMW_END_IN;
always @(negedge CLK or negedge RESET_N)
begin
if(!RESET_N)
begin
state <= UIM_START;
mux <= 1'b0;
rw <= 1'b1;
ena <= 1'b0;
timer <= 14'b00000000000000;
timer_ena <=1'b0;
AMW_END_OUT_ST <= 1'b0;
end
else
begin
if (timer_ena == 1'b1)
timer <= timer + 1'b1;
case(state)
UIM_START:
begin
if ((MPI_SCS == 2'b00) && (AMW_END_IN == 1'b1))
state <= UIM_F1;
end
UIM_F1:
begin
mux <= 1'b1;
state <= UIM_F2;
end
UIM_F2:
begin
ena <= 1'b1;
state <= UIM_F3;
end
UIM_F3:
begin
rw <= 1'b0;
state <= UIM_F4;
end
UIM_F4:
begin
if (PH_2)
begin
rw <= 1'b1;
state <= UIM_F5;
end
end
UIM_F5:
begin
ena <= 1'b0;
state <= UIM_F6;
end
UIM_F6:
begin
mux <= 1'b0;
timer_ena <= 1'b1;
state <= UIM_ST_END;
end
UIM_ST_END:
begin
if (timer[13] == 1'b1)
begin
AMW_END_OUT_ST <= 1'b1;
timer_ena <= 1'b0;
end
end
default:;
endcase
end
end
endmodule